kawasaki mule fuse panel 4010

You search Auto repair manual PDF kawasaki mule fuse panel 4010, if there are search results will appear below. If search results do not exist, please search by others keyword.





HARLEY DAVIDSON DASH PANEL EXTENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION 1. Remove the seat. 2. See Figure 1. Loosen the two socket head screws on the instrument panel console. Raise the console enough to access the two pushnuts holding the upper end of the leather insert. Remove and discard the pushnuts using pliers or a blade-type screwdriver. 3. Remove and discard the phillips head screw (3) and washer (4) securing the lower portion of the leather insert to the fuel tank. Remove the leather insert and discard it. 4. Obtain the dash panel extension (1) and the dash panel extension trim (2) from kit. Place the dash panel extension on the dash panel extension trim making sure the panel is centered and fits cleanly into the lips on both sides of the trim. 5. Gently lift up on the rear of the instrument panel console and install the dash panel extension with the rubber dash panel extension trim underneath, butting the two together. Make sure the rubber dash panel extension trim is aligned with the dash panel extension. Finger tighten the two socket head screws to hold down the instrument panel temporarily in place. NOTE The console rubber trim from a stock vehicle may need to be trimmed slightly to assure proper fit. NOTE When performing the next step, note that proper alignment is achieved when space is eliminated between the instrument panel console and/or between the dash panel extension trim piece and the fuel tank. Due to variances in fuel tank and instrument panel console fitments, the foam pads are used on “as needed” basis to achieve proper alignment. It may be necessary to experiment a few times using various combinations of pads to achieve the desired alignment. In some cases, pads may not be necessary while in others, it may be necessary to use all with one stacked above another. 6. Observe the overall fitment of the panels over the tank and determine whether the foam pads will be necessary to achieve the desired alignment. 7. If necessary, remove the dash panel extension assembly. Peel the adhesive backing and install the needed foam pads (5) to the raised areas extending from the front of the dash panel extension as shown. Re-install the panel. 8. When the proper alignment between the new kit and the fuel tank is achieved, tighten the rear mounting screw (3) with the washer (4) to the speed nut located on the tab at the rear of the fuel tank. 9. Tighten to 18-24 in-lbs (2.0-2.7 Nm). 10. Tighten the instrument panel console?s two socket head screws to 18-24 in-lbs (2.0-2.7 Nm). 11. Install the seat

Incoming search terms:

YAMAHA FJR1300N PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 17-12-2010

download
Always keep the battery charged. Storing a discharged battery can cause permanent battery damage. ● To charge a sealed-type (MF) battery, a special (constant- voltage) battery charger is required. Using a conventional battery charger will damage the battery. If you do not have access to a sealed-type (MF) battery charger, have a Yamaha dealer charge your battery. EAU04076* Replacing the fuses The fuse box, which contains the fuses for the individual circuits, is located under panel D. The fuel injection system fuse box is located under panel D. The main fuse box is also located under panel D, beside the battery. (See page 6-7 for panel removal and installation procedures.) If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. 1. Fuel injection system fuse 2. Spare fuel injection system fuse 1. Headlight fuse 2. Signaling system fuse 3. Ignition fuse 4. Windshield motor fuse 5. Radiator fan fuse 6. Backup fuse (odometer and clock) 7. Spare fuse (〈 4)
PERIODIC MAINTENANCE AND MINOR REPAIR 6-31 6 EC000103 CAUTION: Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive damage to the electrical system and possibly a fire. 3. Turn the key to “ON” and turn on the electrical circuit in question to check if the device operates. 4. If the fuse immediately blows again, have a Yamaha dealer check the electrical system. EAU04099 Replacing a headlight bulb This motorcycle is equipped with quartz bulb headlights. If a headlight bulb burns out, replace it as follows. 1. Remove panel B (if replacing the left headlight bulb) or panel C (if replacing the right headlight bulb). (See page 6-7 for panel removal and installation procedures.) 2. Disconnect the headlight coupler, and then remove the headlight bulb cove

Incoming search terms:

HARLEY DAVIDSON LEATHER FUEL TANK PANEL INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION Softail Models NOTE Generic leather tank panel shown for illustration purposes. 1. Refer to Owner’s manual for removal of seat. 2 3 1 is00927 1. Instrument panel 2. Nut 3. Masking tape Figure 1. Leather Fuel Tank Panel Installed 2. See Figure 1. Remove nut (2) securing instrument panel (1). Gently lift instrument panel up and turn it so stock fuel tank panel front end is uncovered. 3. Place a shop towel under instrument panel and set instrument panel on fuel tank. 4. See Figure 2. Remove lower mounting screw and washer (1) and retain for reinstallation. 5. Lay leather tank panel on tank in desired position. 6. Install screw and washer saved in Step 4 into hole on tank panel. Tighten screw finger tight. 1 is02467 1. Save screw and nut for reinstallation Figure 2. Softail Tank Panel Installs With Original Screw And Nut 7. See Figure 1. Install instrument panel (1) and tighten nut (2) to 8 ft-lb (11 Nm) . 8. Tighten lower mounting screw. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 9. Install seat on the motorcycle by inserting the tab at front of seat into slot at the rear of fuel tank. Secure seat to fender with screw. INSTALLATION FXDWG and FXDC NOTE Generic leather tank panel shown for illustration purposes. 1. Refer to Owner’s manual for removal of seat. 2. 1993-2003 Models: Figure 1. Remove nut (2) securing instrument panel (1). Gently lift instrument panel up and turn it so stock fuel tank panel front end is uncovered. 2004 and later Models: See Figure 4.

Incoming search terms:

Harley-Davidson FLH Accent Panel Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1 Install Accent Panels Note: See hardware list on Page 4 for usage and descriptions. 1.1 Elevate the rear of the vehicle and support with jack stands under the rear differential tubes. 1.2 Remove the rear wheels 1.3 Remove the passenger foot rests. 1.4 Remove front fairing (for wiring later in installation) . 1.5 Install cross brace and frame clamps to frame in the approximate position shown in Figure 1. 1.6 Note orientation of cross brace (Figure 2). Flat side of the brace against bottom of frame tubes. Outboard tabs up and to the rear of the vehicle. 1.7 Leave the bolts loose to allow the bracket’s position to be adjusted later in installation. 1.8 Install front brackets to vehicle between the frame and crash bars as shown, using the supplied hardware (the left side bracket is longer than the right. Figure 3 1.9 Leave the bolts loose to allow the bracket’s position to be adjusted later in installation. 1.10 Position the accent panel to vehicle. Figure 4 1.11 Install supplied hardware to front and cross brackets. Figure 5 &Figure 6 1.12 Leave the bolts loose to allow the accent panel’s position to be adjusted later in installation. 1.13 If not already preinstalled to your accent panel, install rubber bead edge molding between trike body (fender) and accent panel. Bead edge molding 1.14 Clamp the accent panel to the body (fender). Check position of accent panel and ensure proper positioning of bead edge molding. 1.15 Four holes will be drilled though body (fender) and accent panel in the approximate positions shown (both left and right accent panels). Figure 8 Note: Hole location dimension in Figure 8 are approximations. Your drill location may and can vary. Note: Hole position should be as high an possible on the accent panel, allowing space to install hardware 1.16 With accent panel and bead edge molding properly positioned and clamped to body (fender), Drill the two outboard holes in the approximate position shown from inside the fender well through mounting surface of accent panel. Note: Drill outboard hole first and install hardware to reduce risk of accidental movement. Figure 9 1.17 Drill remaining two inboard holes from the accent panel mounting surface through the body (fender). Figure 10 1.18 With both left and right accent panels installed, tighten all hardware at the left and right front mounting positions. 1.19 Trim off excess bead edge molding. 1.20 With left and right front mounting secure, check position and alignment of cross bar and accent panel mid mounts and tighten all hardware. 1.21 With fairing removed, crimp supplied xxx to the black, purple and blues wires of the vehicle’s turn signal wire loom. 1.22 Crimp one of the supplied male spade connectors to the end each wire from the accent panel. 1.23 Connect wiring as indicated in Table 1 below. Accent Panel Wire Color Vehicle Turn Signal Loom Wire Color Yellow Purple (Signal) Orange Blue (Running) Black Black (Ground) Table 1

Kawasaki Mule Roof 600, 610 and 4010 Trans Crew, Roof Installation Manual

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
INSTALLTION INSTRUCTIONS – Mule 600/610 (4010 Trans skip to pg 4) 1. Place Roof Panel on top of UTV Roll cage and center front to back, and left to right. 2. Using Figure 1 Below – place UTV Roof Mounting Brackets around roll cage bar and using a marker, mark the position of the holes needed in the roof for each Roof Mounting bracket . Figure 1 Copyright 2007 DiamondBack Automotive Accessories, Inc. Page 3 3. Next, remove the roof from the roll cage and using a drill with 1/4″ bit, drill holes using the marks as a guide. 4. Cut (4) 3″ strips of adhesive foam and apply to roof in where mounting brackets are positioned to prevent roof rattling once mounted. Foam should run in the direction of the roll cage as shown in Figure 1 above. 5. Next, reposition the roof on the roll cage according to step 1. 6. Prior to attaching the roof mount brackets, cut the remaining adhesive foam in half and apply one section to the roof in the center of the roof where roof and each roll cage bar meet as shown in Figures 1 above. If additional tape is required to prevent rattling it can be purchased from any hardware store as window sealant foam tape. 7. Next, attach the roof mount brackets according to Figure 2. Use channel locks or pliers to hold top of carriage bolt and turn nut with 7/16″ socket.

Incoming search terms:

Kawasaki Teryx 750 Roof / Windshield Kit Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
2. Installation iii) Adhere high density foam gasket to top portion of hood using marker line as centerline guide to ensure windshield panel will sit squarely onto foam after installation. If desired, install small edge trim to side edges of windshield panel and cut to suit. (Steps not shown) iv) Re-install windshield panel onto vehicle. Fasten panel with (6) #10-32 x 3/4″ Lg. screws and nyloc nuts (Fig.4) ensuring windshield panel sits firmly onto foam strip. v) Install and position roof panel onto vehicle allowing for equal spacing on either side of widshield panel edges. Once centered, carefully transfer upper windshield panel holes onto roof panel using a ¼” drill bit. (Fig. 5) NOTE: To prevent excessive rattling noise during operation, install foam strips between roof and rollcage contact points at this time. vi) Fasten roof panel to windshield panel using (6) ¼-20 x 5/8″ screws, washers and nyloc nuts (Fig.6).

Kawasaki Mule Lift Kit Installation Manual

0

Filed Under (Kawasaki) by admin on 04-05-2012

download
Front Lift Installation 1. Ensuring that the parking brake is set, place jack under center of the Mule front end and lift until front wheels clear the ground. Be careful to support Mule properly so that it is secure, but so that the A-arms and struts can droop to full extension. 2. Remove front wheels. 3. If applicable, remove the heater to allow access to the strut mount behind the heater coil. Heater 4. Starting with the left side (driver side), remove the cotter pin and castle nut that secures the strut to the strut mount. Castle Nut & Pen 5. Push bolt through the bolthole, taking care not to damage the brake line that is attached to the bolt. If you are having difficulty removing the bolt, you may have to remove the brake lines that are attached to the front brakes. In this case refer to owners manual for removing brake lines. Screwdriver NOTE: Keep in mind that if you remove the brake lines you must bleed your brakes according to operator’s manual. 6. Once the bottom of the strut has been loosened, then unbolt the top of the strut. The nuts securing the top strut can be located in the dash of the Mule on the left and right sides. In most cases these nuts are easily accessible, but you may have to remove the glove box or heater coils, depending on the model and options purchased with the Mule.

Incoming search terms:

APRILIA FUTURA LEFT FRONT PANEL Installation Instructions

0

Filed Under (Aprilia) by admin on 26-10-2010

download
STEP #1 Remove the left side panel & seat. STEP #2 Mount the socket. STEP #3 Route wires starting at the battery and finishing at the bracket. STEP #4 Attach the wires to the socket and test. STEP #5 Look over your work. STEP #6 Put everything you took off back on. Detailed Instruction: STEP #1 – Remove the seat & the left side fairing. See the Aprilia service manual. STEP #2 – Drill a 18mm hole into the panel (11/16″ hole saw recommended and is available on our site) where shown [A]. There is plenty of room for the knee of a tall rider. An alternate position is show at [E]. There is no need to completely remove the front fairing, just unscrew the bolt under the left handgrip; the panel will flex enough to work behind it. Watch the clearance behind the panel; make sure the socket has room. Attach the socket to the panel; use a dab of Silicone on the socket and jam nut after assembly. Important: Do NOT use Loctite or over-tighten. STEP #3 – Disconnect the battery ground & positive connections. Install the fuse in the fuse-holder. Mount the fuse-holder to the round cross tube [B]. Route the harness up on the inside of the frame piggyback with the seat release cable. The harness can be inserted in the same clip that the seat- release cable uses [F]. Use wire ties to secure it from touching the engine. Connect the red wire to the positive battery posts [C]. The red rubber boot may need to be notched to allow the wire to exit. Connect the ground connection under bolt [D]. Run the black wire along the inside of the frame rail, then pass under the frame rail near the attachment point. STEP #4 -The center terminal is plus and the outer ring is negative (see dwg below). Apply either dielectric grease or Vaseline to terminals. Connect the red wire to the POSITIVE terminal and the black wire to the NEGATIVE terminal. Use a voltmeter to check if the polarity is correct

Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Upgrading the Suspension on the Kawasaki ER6-F/ N

0

Filed Under (Kawasaki) by admin on 30-11-2010

download
Top fork is as removed. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Before removing the fork from the clamps on the yokes I loosened the fork top. Before removing the fork top the fork-slider was placed in a vice and the bottom bolt loosened….. … before finally being removed with the fork upside down. Because the springs were still in situ this gave sufficient tension on the damper-rod to prevent it from turning and allow the bolt to be removed. When I turned the fork the right-way up to remove the fork-top I did it over a container to catch the oil. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource All the OE components that will no longer be required. Left to right. Fork-top, spacer tube, washer, spring, damper-rod. Bottom bolts get re-used. Old and new, laid-out for comparison. The damper unit, minus spring and fork-top, drops inside the stanchion and slider. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Then the bolt goes back in, as tight as possible, to secure it. Top fork is done, second one awaits. Note the spring seat on the right, just below the spring. This drops over the damping rod after the oil has been added. The small locking-nut screws over the threaded part of the damping-rod next, all the way to the bottom. Spring drops in and then the fork-top screws on to the damping-rod as well, all the way down to the lock-nut which is used to secure it. At this point the stanchion is extended to the fork-top which is screwed in. Job done.

Incoming search terms:

YAMAH FJR PERIODIC MAINTENANCE AND MINOR REPAIR MANUAL

0

Filed Under (Yamaha) by admin on 22-11-2010

download
Battery The battery is located under panel D. (See page 6-7 for panel removal and installation procedures.) This motorcycle is equipped with a sealed-type (MF) battery, which does not require any maintenance. There is no need to check the electrolyte or to add distilled water. To charge the battery Have a Yamaha dealer charge the battery as soon as possible if it seems to have discharged. Keep in mind that the battery tends to discharge more quickly if the motorcycle is equipped with optional electrical accessories. EW000116 WARNING ● Electrolyte is poisonous and dangerous since it contains sulfuric acid, which causes severe burns. Avoid any contact with skin, eyes or clothing and always shield your eyes when working near batteries. In case of contact, administer the following FIRST AID. •EXTERNAL: Flush with plenty of water. •INTERNAL: Drink large quantities of water or milk and immediately call a physician. •EYES: Flush with water for 15minutes and seek prompt medical attention. ● Batteries produce explosive hydrogen gas. Therefore, keep sparks, flames, cigarettes, etc., away from the battery and provide sufficient ventilation when charging it in an enclosed space. ● KEEP THIS AND ALL BATTERIES OUT OF THE REACH OF CHILDREN. To store the battery 1. If the motorcycle will not be used for more than one month, remove the battery, fully charge it, and then place it in a cool, dry place. 2. If the battery will be stored for more than two months, check it at least once a month and fully charge it if necessary. 3. Fully charge the battery before in- stallation Replacing the fuses The fuse box, which contains the fuses for the individual circuits, is located under panel D. The fuel injection system fuse box is located under panel D. The main fuse box is also located under panel D, beside the battery. (See page 6-7 for panel removal and installation procedures.) If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage.

Incoming search terms: