klr 650 idle adjustment

You search Auto repair manual PDF klr 650 idle adjustment, if there are search results will appear below. If search results do not exist, please search by others keyword.



  klr 650 idle adjustment Direct Download speed 5282 Kb/s

  klr 650 idle adjustment Full Version speed 6162 Kb/s



Ural carburetors Installation and idle adjustment

0

Filed Under (Ural) by admin on 02-11-2010

download
1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

2008 KAWASAKI KL650A8F: KLR 650 General And Tuning Engine Specifications

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
Engine Type 4-stroke, Inline, 1-cylinder, DOHC, Liquid cooled Displacement 651 cc Bore x Stroke 100.0 x 83.0 mm Compression Ratio 9.8:1 Maximum Torque 36.9 lb-ft at 5,500 rpm Carburetor Keihin CVK40, Constant velocity, Diaphragm-type Ignition System Magneto CDI (Rotor) Ignition Advance Electronic Crankshaft Rotation Clockwise from ignition (RH) side Cylinder Material Aluminum alloy with ferrous sleeves Fuel Min 91 Research/87 Avg. Oct. Unleaded OK Coolant 50% distilled water/50% ethylene glycol base antifreeze —Capacity 1.05 L (1.1 qt.) —Level Level with radiator filler neck. Transmission Clutch Type Wet, Multi-disc, Manual Transmission 5-speed, Constant mesh, Return shift Shift Pattern(Bottom up) 1-N-2-3-4-5 Gear Ratios —1st 2.27 (34/15) —2nd 1.44 (26/18) —3rd 1.14 (25/22) —4th 0.95 (21/22) —5th 0.79 (19/24) Primary Ratio 2.28 (75/33) Final Ratio 2.87 (43/15) Overall Ratio (Top Gear) 5.157 Chassis Wheelbase 1,480 mm (58.3 in.) Seat Height 890 mm (35.0 in.) Ground Clearance 210 mm (8.3 in.) Dry Weight 175 kg (386 lb.) Fuel Tank Capacity 22.1 L (5.8 gal.) Tire Size —Front 90/90-21 54S —Rear 130/80-17 65S Brake Type —Front Single Hydraulic Disc —Rear Single Hydraulic Disc Brake Size —Front 254 mm Effective Diameter —Rear 212 mm Effective Diameter Wheel Travel —Front 206 mm (7.9 in.) —Rear 185 mm (7.3 in.) Model Identification Year & Model ’08 KL650A8F:KLR 650 Color 1. Blue 21 (S8) 2. KMT. Candy Lime Green (175) 3. Sunbeam Red (H1) VIN Range JKAKLEE1 * 8DA00101 — Engine No. Range KL650AE007501— Engine No. Location RH top crankcase, below carburetor Tuning Specifications Engine Valve Clearance (Cold) Intake: 0.10-0.20 mm Exhaust: 0.15-0.25mm —Adjustment Method Shim on tappet Spark Plug NGK DPR8EA-9 or ND X24EPR-U9 —Gap 0.8-0.9 mm Ignition Timing 10.0° BTDC (“F” mark) at 1300 rpm 30.0° BTDC (In double marks) at 3300 rpm Pilot Screw Sealed—not adjustable Idle Speed 1300 ±100 rpm Engine Oil API SE, SF, or SG, API SH or SJ of JASO MA Class, 10w40 —w/Filter Change 2.5 L —No Filter Change 1.7 L —Level On center stand, wait 5 min, middle of window —Pressure (Hot) 2.0-2.5 kg/cm2 at 4,000 rpm, 90° C Chassis Fork Oil SAE 10W20 —Capacity 581 – 589 cc dry —Level 170 ±2 mm (fork compressed, spring removed) Fork Air Pressure (Cold) 0.0 kg/cm2 , max 2.5 kg/cm2 Tire Pressure (Cold) —Front 22 psi, change for course and rider preference —Rear 22 psi, change for course and rider preference Drive Chain Slack 35-45 mm (on center stand, tightest point, STD)

Incoming search terms:

Single-Cylinder BMW G 650 X Model Series

0

Filed Under (BMW) by admin on 16-11-2010

download
introducing the new range of single-cylinder models, BMW Motorrad is broadening its model line-up with a clear focus on additional target groups. Proceeding from the same technical foundation, the Company has created three new motorcycles absolutely different in their features and characteristics: the G 650 Xchallenge Hard Enduro, G 650 Xmoto Street Moto, and the G 650 Xcountry Scrambler. With their outstanding product substance, their purist looks, and their exceptionally sporting riding characteristics, these single-cylinder models are filling attractive niches in the market. And through their low unladen weight of less than 160 kg or 353 lb according to the DIN standard, they offer dynamic performance for both the connoisseur and the sports-minded rider. Market launch of the new G 650 X model series is planned in good time for the beginning of the season in spring 2007. These new machines with the smallest engines in the BMW model range offer particularly the young and young-at-heart motorcycle rider exactly the right entry into the world of BMW motorcycles, but are not entry-level bikes in the conventional sense of the word: On the contrary, the G 650 Xchallenge Hard Enduro will thrill the customer who wishes to really benefit from the enormous offroad potential of his machine. The G 650 Xmoto Street Moto, in turn, with its very impressive active riding qualities, offers the genuine enthusiast a new dimension in riding pleasure. The G 650 Xcountry Scrambler, finally, stands for carefree riding pleasure and nimble performance both on the road and off the beaten track. Indeed, this unique machine is able to meet all kinds of requirements and offer virtually all riding qualities ranging from city use via country roads and small, winding lanes, all the way to offroad tracks presenting the most challenging requirements. The G 650 Xcountry therefore conveys the classic but relaxed feeling of riding a genuine Scrambler as well as the concept of “wandering” on your motorcycle into today’s world in a most modern style. And last but certainly not least, riding pleasure is guaranteed under all conditions and in every situation, since the G 650 Xcountry offers the same outstanding engine and running gear qualities as its two very sporting “sister models

Incoming search terms:

Kawasaki KLR-650 465 Series Single Shock Supplement

0

Filed Under (Kawasaki) by admin on 13-02-2011

download
Mount the shock as you would your stock shock per your authorized shop manual (with the rebound adjustment at the bottom) noting the following: n As you mount the shock, feed the Remote Adjustable Pre-Load adjuster through the opening between the main-frame and sub-frame on the left side of the bike. n Do not loosen or attempt to rotate the line between the shock and the adjuster. n Make sure the shock rebound adjustment is facing the right side of the motorcycle and the pressure valve is facing forward. n On 1987-2007 models ONLY , install the supplied 3.5mm thick spacers – one on each side of the shock clevis ( see figure 3 ). Do not install these spacers on 2008-2010 models. n Tighten shock bolts to the proper torque specifications (refer to your manual). n Mount the adjuster to the supplied mounting bracket using the supplied M6- 1.0X8mm SHCS fasteners and torque them to 80-90 in/lbs (9-10 N-m). Then mount the bracket to the bike using the two rear footrest mounting bolts – sandwiching the mounting bracket between the rear footrest mount and the frame tabs (as shown in figure 4) . Using the supplied zip-ties, secure the hydraulic line away from any moving parts or heat sources. n To adjust the ride height, simply turn the adjuster knob clockwise (looking at it from the back of the bike) to increase the height and counterclockwise to reduce it. See main instructions for procedure of achieving optimum ride heigh

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

2008 KAWASAKI KLR 650 REAR LINE INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 13-01-2011

download
The OEM brake line for your bike was routed behind / under the caliper. This caused the line to loop around the caliper. Your Galfer brake line is cut shorter so it can be routed down the swing arm and into the “C” clip pictured. This eliminates the extra hose that could get caught on a bush, tree, rock, etc. New Galfer “C” clip must be installed with the new hose using the existing stock bolt.

KAWASAKI KLR 650 SADDLEBAG INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 24-10-2010

download
INSTALLATION INSTRUCTIONS Place the saddlebags on the rear of the seat. Adjust the velcro connections over the seat as necessary. Thread the rear strap as seen in photo 1. and connect the buckles. Cinch and tuck the excess webbing as necessary. Thread the front strap down and through the foot guard as seen in photo 2. ® 5-7-07 WARRANTY INFORMATION Your new Kawasaki accessory is guaranteed to be free from defects in material and workmanship for 90 days from date of purchase. CARE & CLEANING Do not carry sharp or pointed objects. Maximum Weight-5 lbs. (2.2 kg.) Each bag Be sure the saddlebags do not interfere with any operarating or wiring components. Photo 1. Photo 2. ISK57003100/R1

Kawasaki KLR 650 Fork Brace Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Place your motorcycle on its center stand or appropriate support stand. Slide up fork boot (if applicable) from fork leg. 2. Remove the two outer caps (6mm x 16mm bolts), and slightly loosen the inner bridge mounting bolts (6mm x 50mm bolts). 3. Position the Fork Brace assembly, so it is level side to side. Then fasten the outer caps on each side making sure it is resting all the way down on the fork tubes. The spacers provide MUST be used for adequate tire clearance. 4. Now check the bridge if it is free of tension. Move your front forks through the suspension travel. 5. Tighten the inner bridge bolts securely, and then collapse the forks completely to check for interference with any accessories or fender. Make sure you have nothing causing your suspension to bind. Slip your fork boots over the Fork Brace. Installation is now complete. Double check all nuts and bolts for tightness. Recheck all nuts and bolts after a short test ride. Periodically check bolts as part of your pre-ride inspection. * WARNING: Ride stability and handling will be greatly improved with Fork Brace, provided your motorcycle complies with the manufactures specifications. BE SURE that the front tire is properly inflated and balanced, and not out-of-round. Check to see that front and rear suspension air pressure and oil levels are correct. Failure to comply with any or all set standards may adversely affect the handling of your motorcycle

Incoming search terms:

Kawasaki KLR 650 Hydraulic Clutch Installation Manual

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Now, the clutch safety interlock switch. The picture above shows the safety switch contacts. Once you removed the 2 screws holding it to the stock lever, you will need to cut the copper plate on the switch. There are 3 wires: Green, Black with yellow and Blue. You do not use the green wire. You will need to attach the supplied terminals to the remaining wires and slip the supplied rubber boot over them as you attach them to the hydraulic clutch lever. In the photos, the boot is installed and also removed, and with my finger, I am pointing to its location. I did not bother to install the clutch interlock switch and removed the wiring harness completely, but unplugging it from the connector behind the instrument panel. Next, you must remove the clutch cable from the lever in order to pass the cable under the steering head he picture above shows the attachment at the clutch actuator Once the clutch cable is removed from the lever, remove the bolt holding it at on the engine case and disconnect the clutch cable from the pivot. The easiest way to do this is to pull out the clutch pivot assembly and the long “spike” out of the clutch plate hole. (It only goes back in one way, so you can’t mess it up.) he picture above shows that the routing is the same as the original clutch cable. With the hydraulic clutch assembly, pass the stainless steel braided line to the clutch “pivot” point at the engine casing. Attach the clutch cable to the “pivot” while it is removed from the engine, then insert the “spike” into the clutch plates hole (it can only go in one way).

Adjusting the Pekar K68 for Dnepr or Ural

0

Filed Under (Tips and Review) by admin on 11-11-2010

download
1. Make sure the ignition timing is correct 2. Adjust the valves as necessary to ensure proper operation 3. Run the engine to warm it up a bit 4. Adjust the float setting. To do this, remove the carburetors (leave the throttle cables attached), remove the bowl and turn the carburetor upside down (fuel will spill). The float should look like this: Adjust as necessary by bending the float support (#37 in Figure 1). Reinstall Installation and idle adjustment 1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns. * Starting using the K68′s (cold weather) 1. Verify fuel flow. Apply choke (pull 52 in Fig1). 2. Using the ticklers (13) allow fuel to enter the bowl until fuel drains from (14) 3. With the ignition off, kick 1 or 2 times 4. Turn ignition on, and as soon as engine is warmed up (maybe sooner) push choke mechanisms to open choke Idle Adjustment (engine running and warm) 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

Incoming search terms: