kndi atv instructions

You search Auto repair manual PDF kndi atv instructions, if there are search results will appear below. If search results do not exist, please search by others keyword.



  kndi atv instructions Direct Download speed 5282 Kb/s

  kndi atv instructions Full Version speed 6162 Kb/s



KYMCO MXU 375 ATV WINCH MOUNT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kymco) by admin on 26-10-2010

download
WINCH MOUNT INSTALLATION INSTRUCTIONS 1. Remove molded plastic bumper guard from the ATV. 2. Mount the winch mount weldment (Item 1) to the ATV as shown below. 3. Mount the roller hawse to the winch mount weldment as shown above. 4
4. Mount the winch to the winch mount weldment and route the winch cable through the rollers. (Installer may need to remove rollers to allow cable end to pass through). 5. Wire the winch according to the manufacturer instructions. 6. Re-install the molded plastic bumper guard. 5 *CAUTION BE AWARE OF WHEN THE CABLE STOP CONTACTS THE ROLLER HAWSE AS CABLE IS WOUND IN. FAILURE TO RELEASE MAY CAUSE DAMAGE TO WINCH PARTS OR TO THE ATV. When using the winch to raise and lower a blade a cable stop must be installed. Carefully raise the blade until the top of the push tube’s are no closer than 1″ anywhere on the ATV. Place the Cable Stop onto the Winch Cable up against the Winch Hawse. Secure the Cable Stop to the Winch Cable using the Cable Clamp Assembly as shown in the pictures below.

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
REMOVAL 1. Refer to the owner’s manual and follow the instructions to disarm the security system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. For All Models except 2002-2003 Touring and 2003- Later Softail: Refer to the owner’s manual and follow the instructions to disconnect the battery, negative (-) cable first or remove the main fuse. For 2002-2003 Touring and 2003-Later Softail Models: Remove seat following the instructions in the service manual and disconnect the battery, negative (-) cable first. Save seat hardware for installation. INSTALLATION 2002-2006 VRSCA, VRSCB, VRSCD Models 1. Open the seat. 2. See Figure 1. Remove the splash guard (mud flap) nuts. 3. See Figure 2. Lower the mud flap from the installed position and allow it to rest on the rear tire 3. Slide the siren into place on the left side of the electrical caddy so the sounder disc (6) faces out. 4. Refer to the owner’s manual and follow the instructions to install the main fuse. 5. Align the barbed studs on the side cover with the grommets in the frame and push side cover firmly into place. 6. Install the left side saddlebag per the instructions in the owner’s manual. 2003 and later Softail Models EXCEPT FXCW/C 1. Remove the right side saddlebag (if equipped) per the instructions in the owner’s manual. NOTE The siren connector is installed on an electrical panel under the rear fender on all Softail models. The rear of the motorcycle may have to be raised slightly to allow removal of the splash guard. 2. Remove the two bolts at the bottom of the splash guard. Bend the upper right corner of the splash guard toward the rear tire and lift upward to unhook the splash guard from the tab on the rear fork. Remove the guard from beneath the fender. 2 1 3 is01316 1. Siren mounting area 2. Siren connector [142B] 3. Harness clip Figure 16. Siren Connector (Softail Models EXCEPT FXCW/C) (Rear Fender View with Rear Wheel Removed) 3. See Figure 16. Remove the siren connector [142B] (2) from the receptacle in the siren mounting area (1) of the electrical panel. 4. See Figure 17. Insert security siren (1) connector [142B] into the siren box receptacle until the connector latches securely. 5. Orient the siren (1) as shown, with the harness connector (2) toward the bottom and the sounder disc (5) facing out. Carefully snap the siren into the electrical panel. 6. Insert the siren harness lead (4) into the harness clip (3) to keep the harness clear of other components. 7. If necessary, secure the connector wiring to the electrical panel wiring with a cable strap (not provided). 8. Hook the slot at the top of the splash guard over the tab on the rear fork and install the guard with the two screws removed earlier. Tighten securely. 9. Install the right side saddlebag (if equipped) per the instructions in the owner’s manual. 10. Refer to the owner’s manual and follow the instructions given to connect the battery cables or install the main fuse

Incoming search terms:

2002 Kawasaki 360 ATV WINCH ACCESSORY INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
1. Remove the two 8mm bolts that attach the front bumper assembly to the ATV frame see figure 3. 2. Place Winch mounting plate (A1) into position and fasten the two bent down tabs to the ATV frame using the two 8mm bolts removed in step one, see figure 4, and figure 5. Do not tighten fully at this time. 3. Attach the front of the mounting plate using four 1/4-20 u- bolts (B1), eight lock washers (B2), and eight 1/4-20 hex nuts (B3), see figure 6. 4. Tighten all fastners for the mounting kit at this time. 5. Place winch into position behind the mounting plate. Attach the top two feet of the winch using two 5/16-18 hex cap screws and lock washer. These fasteners will be found in the hardware kit that came with the winch. Note: The winch has floating nuts in its feet. In some instances, a nut may be moved off to one side making it impossible to screw a bolt in. If this becomes the case, take a screwdriver and center the floating nut in the winch to the bolt hole opening. Now attach the bolt through the Winch Plate and into the winch. 6. If using a Cast Hawse Fairlead: It may be neccasary to remove the cast hawse fairlead from the fairlead mounting plate that came with the winch.

Incoming search terms:

Baja BA 250 ATV OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 26-11-2010

download
FUEL AND OIL FUEL Proper fuel is very important for the engine. Ensure there is no dust, dirt, or water which has mixed in the fuel. Use regular unleaded gasoline with an octane number 90 or higher. ENGINE OIL Your 250cc ATV has a four-stroke engine. Please use oil as described in the chart below. By using prescribe oil, you will realize the best lubrication for engine. Use the chart to select a viscosity rating based on the temperature range in your area. NOTE: In very cold weather (below 5°F (-15°C), use SAE10W-30 for good starting and smooth operation. SAE 10W-30 SAE 20W-40 ENGINE TEMP. °C °F -30 -22 40 104 -10 14 0 32 10 50 20 68 30 86 -20 4 FUEL AND OIL 8 LOCATION OF LABELS Read and follow all of the warnings labels on your ATV. Make sure you understand all the labels. Keep the labels on the ATV. Do not remove them for any reason. If a label comes off or becomes difficult to read, you should get a replacement by contacting BAJA INC. 1 – Red Light – Reverse indicator Light illuminates when ATV is in Reverse. 2 – Green Light – Neutral indicator Light illuminates when ATV is in Neutral. 3 – Ignition key switch – Turn right (CW) “RUN”, Turn left (CCW) “OFF”. ATV will only start when ignition key is turned to the “RUN” position. Make sure ignition key switch is in the “OFF” position when not in use

Incoming search terms:

Honda, Polaris (2000 and older) ATV Thumb Warmer Installation Instructions

0

Filed Under (Honda) by admin on 15-12-2011

download
Hi/Low Switch Installation Choose a location for the switch, which is convenient and has sufficient rear clearance for the electrical connections and is within 18″ of a voltage-controlled wire (a wire in the lighting circuit). Drill a 1/2″ (13mm) hole and install the switch from the back. Leave the strain relief nut on the switch. On the front install the Hi/Low indicator tab and secure the switch and tab using the metal nut. The amount of switch barrel protruding can be adjusted by moving the strain relief nut. Wire Routing and Connections Route the electric cord along the handlebar to switchmarea and secure with supplied tie wraps, electrical tape, or both. Cut and strip to proper length. Attach a ground wire of sufficient length to go from the red wire to a good ground. WARNING: Lead wire slack in the area of the throttle must be neither excessive nor tight. Ensure no binding occurs when the throttle is open fully.,Soldering connections is the most durable method, but the following will provide years of service. Attach the 1/4″ female slip-on connectors to the white and blue wires and #10 ring terminal to warmer leads as shown in Figure 2. (A crimping tool works best, but a Vise Grips or pliers will work). Figure 2. Switch Connections (Option B) Connect the single yellow or red wire to a regulated (lighting) circuit using Option A (ATV has a switch in a lighting circuit with a 1/4″ tab) or Option B: Option B: Locate a power wire (usually yellow) leading to a headlight, taillight, or dash light (Figure 2). Using the red tap connector, place this power wire into the continuous channel and insert the red wire (do not strip insulation) completely to stop in the second channel. Make the connection by squeezing (w/pliers) the metal contact until flush with the top of the connector. Close the hinged cover until latched. Complete connections to switch and ground circuit.

Honda 300 2×4 Lift Kit Installation Instructions

0

Filed Under (Honda) by admin on 11-12-2011

download
This product is designed for us e on ATVs on which additional ground clearance and fender clearance is desired. It is designed for utility type, slower-speed use on relatively flat terrain in deep mud or snow. Although we have many thousands of satisfied lift kit customers and over 400 franchised dealers selling and installing lift kits, purchasers should be aware that use of this product may increase the frequency of required maintenance, part wear, and will raise the center of gravity on your ATV increasing risk of roll-over on side hills, ditches or other steep terrain. We recommend that wider tires and/or wheel spacers be used to achieve a wider stance and to improve stability of the ATV. Riders should be advised that the handling characteristics of a taller ATV are different and require extra care when riding on side hills or off-camber situations. If you further raise the center of gravity by adding heavy loads to racks or seats, the ATV must be operated with care, at slower speeds or on relatively flat ground. Operation of an ATV with or without a lift kit, while or shortly after consuming alcohol or drugs, subjects the rider to the risk of serious bodily harm or possible death. This is compounded if the rider does not wear an approved helmet and other safety gear. High Lifter urges that all approved safety gear be worn when riding an ATV. If this is not what you expected, or is not consistent with your intended use, you should return the product immediately to the seller, before installation, for a refund of the purchase price; less any fees. After installation, product is warranted for 90 days for defects in workmanship and materials. Warranty is limited to refund of the purchase price or replacement of the kit, at the seller’s option.

Kawasaki Prairie 360,650,700 ATV PLOW Plow Mounting Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Mount Installation Note: There are different hole locations on the plow mount depending on the bike model. For Prairie 360 use the middle hole locations (B), for Prairie 650 and Twin Peaks 700 use hole locations (A) on mounting plate, as shown in Figure 1. Figure 1 Hole Locations WARN INDUSTRIES PAGE 3 67954 Rev A3 To install the plow mount to the underside of the vehicle install the front two U-bolts PN 60869, and loosely tighten the 5/16″ nuts. Pull the plow mount back in the furthest position and then fully tighten, as shown in Figure 2. For the Kawasaki Prairie 360 use the second set of U-bolts PN 61262 and securely tighten around the frame in hole location (B) . For Kawasaki Prairie 650 and Suzuki Twin Peaks 700 drill a 3/8″ hole through the aluminum skid plate, using the plow mount as a template, as shown in Figure 3. Repeat the same process on the other side. After both holes are drilled attach the mounting plate with the second set of U-bolts PN 61262 and securely tighten around the frame in hole location (A) . Tighten all fasteners securely. Torque 5/16″ Bolts: 20ft. lb.

Incoming search terms:

Kawasaki 650/360 Prairie Lift Kit Installation and removal Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Place jack under center of ATV front end and lift until front wheels clear the ground. Be careful to support ATV properly so that it is securely supported but so that A-arms and shocks can droop to full extension. 2) Remove front wheels. 3) Remove or loosen front plastic. 4) Remove C-clip and nut at the top of the strut. 5) Screw bracket “A” on top of strut to the same torque specifications as the nut. 6) Place the top adapter “A” through the top of the strut mount, and screw the original nut on the top of bracket “A” securing it to the strut mount. Tighten this nut to the required manufacturer specifications and replace the factory C-clip. 7) Repeat the procedure for the other side. 8) Install the wheels, torque wheel lug nuts to manufacturer’s specifications, lower and remove jack. Check for clearance problems or misalignment. Rear Lift 1) Place jack under ATV at the rear of the bottom skid plate and lift until the weight is off of the suspension. Be careful to secure the ATV properly so as not to fall off the jack. 2) Remove the bottom of the shock from the shock mount on the axle. 3) After removing the shock, jack the ATV up 1″-2″ further. 4) Place Bracket “B” between the shock and shock mount with the notched out ends facing downward. Insert stock bolt to secure bracket “B” to the shock mount and the shock. Fasten nut. 5) Insert the new 12x75mm Bolt to the top of bracket “B” and the shock eyelet and secure with a new 12mm nut. 6) Tighten all nuts and bolts to manufacturer’s torque specifications. 7) Install the wheels, torque wheel lug nuts to manufacturer’s specifications, lower and remove jack. Check for clearance problems or misalignment.

HARLEY DAVIDSON CHROME FORK SLIDERS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
REMOVAL 1. Support the motorcycle so the front end is off the floor and the forks are fully extended. 2. Remove the front fender, front brake caliper(s) and front wheel according to instructions found in the Chassis section of the appropriate service manual. NOTE On some models other parts will also need to be removed to access the front forks. See the service manual. 3. For All Models EXCEPT Touring: Drain and remove the front forks. See the service manual. 4. For Touring models equipped with air-adjustable suspension: Bleed the air-adjustable suspension according to the instructions in the appropriate service manual. Wear safety glasses or goggles when servicing fork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) 5. For 2000 and Later Models EXCEPT Touring: See Figure 1. Using a piece of dental floss (or similar material) in a back and forth motion, loosen reflector from fork slider at both ends. Rotate reflector from side-to-side until it can be removed. Save reflector for future use. See Figure 2. Repeat procedure on the opposite side fork slider. Peel off any excess adhesive from both reflectors . Surface must be clean for installation. 6. Disassemble the front fork tubes according to instructions in the service manual. INSTALLATION NOTES The chrome fork sliders included in this kit install in the same manner as the original equipment parts. Refer to the service manual for proper installation procedures. Prior to installation of this kit, check the bores of the new chrome sliders to be certain they are free of dirt and debris or damage to the new sliders may occur. 1. Assemble the front fork tubes, replacing worn seals, bushings or other items as needed. NOTE Do not use an impact wrench to tighten the drain screws. Use of an impact wrench may damage the screws. 2. Tighten the drain screws: •Early Models with 39 mm forks (see Figure 2): Tighten to 13-17 in-lbs (1.5-1.9 Nm) •Early Models with 41 mm forks (see Figure 2): Tighten to 52-78 in-lbs (5.8-8.8 Nm) •Later Models (see Figure 3): Tighten to 52-78 in-lbs (5.8- 8.8 Nm) 3. Fill with TYPE E FORK OIL (99884-80) according to the instructions in the service manual. 4. Install the front fork and any parts that were removed to access the front forks. Install the front fender, wheel and caliper(s) according to instructions in the service manual. 5. For Touring models equipped with air-adjustable suspension: Refill the air-adjustable suspension system after assembly according to the service manual instruc- tions

HARLEY DAVIDSON CENTER-MOUNTED LICENSE PLATE BRACKET KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (-) battery cable. Retain all seat mounting hardware. 2. Remove rear fender and side-mounted license plate bracket following the instructions in the Service Manual. INSTALLATION 1. Assemble and install the rear fender and the center- mounted license plate bracket following the instructions in the Service Manual. 2. Connect the license plate lamp connector following the instructions in the Service Manual. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 3. Install the seat and connect the negative (-) battery cable following the instructions in the Service Manual.

Incoming search terms: