ktm 300 2 stroke colour diagram

You search Auto repair manual PDF ktm 300 2 stroke colour diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ktm 300 2 stroke colour diagram Direct Download speed 5282 Kb/s

  ktm 300 2 stroke colour diagram Full Version speed 6162 Kb/s



KTM 250/ 300/ 380 SX,MXC,EXC ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 12-11-2010

download
Repair manual KTM 250 / 300 / 380 Art No 3206004 -E 2-2C main jet jet needle jet needle air control screw idle adjusting screw idle jet throttle valve Idling range A Operation with closed throttle valve. This range is influenced by the position of the air control screw 1 and the idle adjusting screw 2 . Only make adjustments when the engine is hot. To this end, slightly increase the idling speed of the engine by means of the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Create a round and stable engine speed using the air control screw (basic position of the air control screw = open by 1.5 turns). Then adjust to the normal idling speed by means of the idle adjusting screw. Opening up B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer. Full throttle range D Operation with the throttle fully open (flat out). This range is influenced by the main jet and the jet needle. If the porcelain of the new spark plug is found to have a very bright or white coating or if the engine rings, after a short distance of riding flat out, a larger main jet is required. If the porcelain is dark brown or black with soot the main jet must be replaced by a smaller one. mixture too rich: too much fuel in proportion to air mixture too lean: not enough fuel in proportion to air 1 2 OPERATING RANGES OF THE CARBURETOR 2-3C Carburetor adjustment Basic information on the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95 MOZ). Mixing ratio 2-stroke motor oil : super fuel 1:40 – 1:60. Basic information on a change of the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB:

Incoming search terms:

KYMCO MAXXER 300/ 250 MONGOOSE 300/ 250 SERVICE MANUAL

0

Filed Under (Kymco) by admin on 26-10-2010

download
apply or add designated greases and lubricants to the specified lubrication points. ÑAfter reassembly, check all parts for proper tightening and operation. ÑWhen two persons work together, pay attention to the mutual working safety. ÑDisconnect the battery negative (-) terminal before operation. ÑWhen using a spanner or other tools, make sure not to damage the motorcycle surface. ÑAfter operation, check all connecting points, fasteners, and lines for proper connection and installation. ÑWhen connecting the battery, the positive (+) terminal must be connected first. ÑAfter connection, apply grease to the battery terminals. ÑTerminal caps shall be installed securely. 1 . GENERAL INFORMATION 1-6 ATV 300/250 ÑIf the fuse is burned out, find the cause and repair it. Replace it with a new one according to the specified capacity. ÑAfter operation, terminal caps shall be installed securely. ÑWhen taking out the connector, the lock on the connector shall be released before operation. ÑHold the connector body when connecting or disconnecting it. ÑDo not pull the connector wire. ÑCheck if any connector terminal is bending, protruding or loose. Confirm Capacity 1 . GENERAL INFORMATION 1-7 ATV 300/250 ÑThe connector shall be inserted completely. ÑIf the double connector has a lock, lock it at the correct position. ÑCheck if there is any loose wire

Incoming search terms:

KTM EXC Enduro & SX Motocross REPAIR MANUAL

0

Filed Under (KTM) by admin on 06-03-2012

download
Thanks to a history of competition successes, particularly in off-road racing, KTM motorcycles enjoy a large and loyal following. Established in 1953, KTM (from Kraftfahrzeuge Trunkenpolz Mattighofen where founder, Hans Trunkenpolz, had his engineering works) went through difficult times in the early 1990s. After a takeover, the Austrian company emerged as KTM Sportmotorcycle AG and has gone from strength to strength in recent years. Mainstay of their range are their Enduro and Motocross models, the EXC and SX, and these are covered in the latest new manual from Haynes. Models covered are the 250, 400, 450, 520 and 525 EXC and SX with 4-stroke sohc engines, 2000 to 2007. Information has also been included on the SMR Supermoto versions and MXC/XC derivatives. Haynes Manuals for cars and motorcycles are so popular that 150 million have been sold worldwide. Lay them end-to-end and they would circle the globe at the equator! The new manual begins with essential pre-ride checks, competition prep and routine maintenance tasks before moving on to more major repairs. There are comprehensive, fully illustrated, instructions for overhauling the engine, transmission, brakes, suspension and electrical system. Useful reference pages include colour wiring diagrams, fault-finding charts and a comprehensive section on tools and workshop tips. Because all Haynes Manuals are based on a complete stripdown and rebuild, not only are the procedures written from first-hand experience, but there is information about special tools required for each job, and its complexity, plus Haynes tips for saving time and money. The new Haynes KTM EXC Enduro & SX Motocross Manual is the only complete manual for owners of these motorcycles.

Incoming search terms:

KTM 125 EXC, EXC SIXDAYS 200 XC, XC-W, EXC 250 XC, XC-W, EXC, EXCSIXDAYS 300 XC, XC-W, EXC-E, EXC-ESIXDAYS OWNER'S MANUAL 2008

0

Filed Under (KTM) by admin on 02-12-2010

download
Chassis number The chassis number is stamped on the right side of the steering head tube. Enter this number in the field on page no 1. Engine number, engine type The engine number and the engine type are stamped into the left side of the engine below the engine sprocket. Enter this number on page 1. Clutch lever The clutch lever [1] is located on the left side of the handlebars. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hand brake lever The hand brake lever [2] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [B] can be used to change the basic position of the hand brake lever (see maintenance work on chassis and engine). OPERATION INSTRUMENTS » 1 2 A B
ENGLISH 6 OPERATION INSTRUMENTS » TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions. SPEED display mode / H (service hours) Only the SPEED / H and SPEED / ODO display modes are activated in the condition at delivery. SPEED/H is displayed whenever the display is activated and the front wheel is not turning. It automatically changes to the SPEED/ODO display mode as soon as the front wheel starts turning. SPEED displays the speed. H displays the engine’s service hours. The service hour counter starts to count as soon as you start the engine. The displayed figure cannot be changed. Service intervals are indicated in service hours for some KTM offroad motorcycles, making the service hour counter a very practical function. SPEED / ODO display mode (odometer) The SPEED/ODO mode displays the speed and the total distance traveled. The display automatically changes to the SPEED/H display mode when the front wheel stops turning. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. changes to the next display mode The electronic speedometer has a number of display modes (functions) that you can also activate (reveal) (see: Activating and deactivating display modes).
ENGLISH 7 OPERATION INSTRUMENTS » SPEED / LAP (lap time) display mode You can use the manual stop watch to stop and store up to 10 lap times, which you can view in the LAP/LAP display mode (see below). LAP displays the lap times in hours, minutes and seconds. + button Starts and stops the stop watch, lap time is not reset to 0 – button Stops the stop watch, stores the lap time and restarts the stop watch again. The time is reset to 0. A total of 10 lap times can be stored. If the lap time continues to run after you press the – button, all 10 memory locations are occupied.To clear all of the stored lap times, hold the button for 3 seconds in the SPEED/LAP mode.Up to 10 lap times can be stored in this way. briefly press buttonChanges to the next display mode.If no lap time is stored or the motorcycle is driving, the LAP/LAP mode will be skipped. hold button 3 secs. Clears all LAP figures SPEED / CLK (time) display mode CLK displays the time in hours, minutes and seconds. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. set the clock menu To set the clock, see „Setting the clock”. Activating and deactivating display modes In the display mode SPEED/H, press and hold the button for 3 seconds to access the SETUP menu. The active functions will be displayed. The blinking function can be activated by pressing the + button and deactivated by pressing the – button. Press and hold the button 3 seconds to store the settings. If no button is pressed for 20 seconds, the setting will be stored automatically and the display will return to the SPEED/H mode. + button activates the blinking display – button deactivates the blinking display briefly press buttonchanges to the next display without changing any settings hold button 3 secs. starts the SETUP stores the settings and changes to the SPEED/H mode

Incoming search terms:

KTM 250/300/380 SX,MXC,EXC ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 19-11-2010

download
Carburetor adjustment Basic information on the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95 MOZ). Mixing ratio 2-stroke motor oil : super fuel 1:40 – 1:60. Basic information on a change of the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. Checking the setting of the TVC system The function of the TVC system is checked with the engine running. This test checks the start of advance and the end of advance. -For this, remove the left control cover. -Connect a rev counter (either to the ignition cable or to the blue/white cable in the electronics box, depending on the rev counter design). -Start engine, accelerate gently and observe when the TVC system starts to advance (tooth segment creeps upwards) Bleeding of the hydraulic clutch -Take off cover together with rubber bellows. -At the slave cylinder of the clutch, remove the bleeder nipple 2 . It its place, mount the bleeder syringe 3 which is filled with SAE 10 hydraulic oil

2008 KTM Model Engine Oil Recommendation Chart

0

Filed Under (KTM) by admin on 24-11-2010

download
2008 Model Type Recommended Engine Oil Type Quantity SPORTMINICYCLES AC 50 SX MINI Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L SPORTMINICYCLES LC 50 SX JUNIOR Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 50 SX Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 65 SX Motorex Top Speed 4T 15W50 0.5L SX 2 STROKE 85 SX Motorex Top Speed 4T 15W50 0.5 L 105 SX Motorex Top Speed 4T 15W50 0.5 L 125 SX Motorex Top Speed 4T 15W50 0.7 L 144 SX Motorex Top Speed 4T 15W50 0.7 L 250 SX Motorex Top Speed 4T 15W50 0.7 L SX 4 STROKE 250 SX-F Motorex Power Synt 4T 10W50 1.1 L 450 SX-F Motorex Power Synt 4T 10W50 1.35 L 505 SX-F Motorex Power Synt 4T 10W50 1.35 L CROSS COUNTRY 2 STROKE 65 XC Motorex Top Speed 4T 15W50 0.5L 85 XC Motorex Top Speed 4T 15W50 0.5L 105 XC Motorex Top Speed 4T 15W50 0.5 L 200 XC Motorex Top Speed 4T 15W50 0.7 L
200 XC-W Motorex Top Speed 4T 15W50 0.7 L 250 XC Motorex Top Speed 4T 15W50 0.7 L 250 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L 300 XC Motorex Top Speed 4T 15W50 0.7 L 300 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L CROSS COUNTRY 4 STROKE 250 XC-F Motorex Power Synt 4T 10W50 1.1 L 250 XC-F-W Motorex Power Synt 4T 10W50 1.1 L 450 XC-F Motorex Power Synt 4T 10W50 1.35 L 450 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 505 XC-F Motorex Power Synt 4T 10W50 1.35 L 530 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L ENDURO RACING 450 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 530 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L SUPERMOTO LC4 690 Supermoto Motorex Power Synt 4T 10W60 Approx. 2.0 L SPORT ATV 450 XC Motorex Power Synt 4T 10W50 2.0 L 525 XC Motorex Power Synt 4T 10W50 2.0 L LC8 950 Super Enduro (R) Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure S Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke R Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L

Incoming search terms:

KTM 125 SX, EXC 200 EXC, XC, XC-W 250 SX, EXC, XC, XC-W 300 EXC, XC, XC-W OWNER'S MANUAL

0

Filed Under (KTM) by admin on 27-11-2010

download
Short circuit button (SX) The short circuit button [1] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Combination switch (EXC) The light switch has 2, respectively 3 switch positions. [A] = Light off (this function is not available in all models) [B] = Low beam on [C] = High beam on You may use button [2] to actuate the horn. The red short circuit button [3] serves to switch off the engine. Leave the switch pressed until the engine stops. Headlamp switch (XC-W) In this model the headlamp is switched on with the pull switch [4] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Emergency OFF switch (Australia) The emergency OFF switch [5] is located next to the throttle grip. Primarily designed as safety or emergency OFF switch, it should normally not be in its activated state. In this position, the ignition circuit is shorted; if the engine is running, it will stall immediately, if it is at standstill, it will not start. In this position, the ignition circuit is enabled; the engine should start. 1 2 3 5 A B C 4
ENGLISH 12 Filler cap To open it: turn filler cap counter-clockwise. To close it: put filler cap back on and tighten it by turning it clockwise. Install tank breather hose [1] without kinks. Filler cap (XC, XC-W) To open the filler cap: Turn the filler cap 45 ° counter-clockwise. To close the filler cap: Put the filler cap on and turn it 45 ° clockwise. Fuel tap OFF In this position the fuel tap is closed. No fuel can flow to the carbure- tor. ON During operation the twist grip must be turned to ON. This means that the fuel can flow to the carburetor. With the twist grip in this position the tank will be emptied until only the reserve is left. RES The reserve tank cannot be tapped until the rotating handle is turned to the RES position. Fill the tank as soon as possible and remember to turn the rotating handle back to the ON position so that you will have backup fuel next time, too. Reserve of the 8.5 l tank . . . . . . 1.3 l (0.32 USgallons) Reserve of the 10 l tank . . . . . .1.7 l (0.45 USgallons

KTM 125/ 200/ 250/ 300 SX, MXC, EXC SERVICE MANUAL

0

Filed Under (KTM) by admin on 28-11-2010

download
Compression damping of shock absorber (MXC, EXC) The compression damping (during compression) can be adjusted for the MXC and EXC shock absorbers (Mono Compression Control). The degree of damping can be adjusted by turning adjusting screw 1 with a screwdriver. Turning in a clockwise direction will increase the damping, turning in a counterclockwise direction will decrease the damping. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X757…………..17 clicks Type White Power 1218X759…………..17 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . NEVER TRY TO TAKE THE SHOCK ABSORBER APART OR TO DO ANY MAINTEN – ANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 2 CONNECTION (24 MM ). Rebound damping of shock absorber (SX, MXC, EXC) By using the adjusting screw 3 , the degree of damping of the rebound can be adjusted. Turn the knob to the right side to increase damping, turn it to the left side to reduce damping during rebounding. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X756…………..28 clicks Type White Power 1218X757…………..28 clicks Type White Power 1218X759…………..26 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . N EVERTRYTOTAKETHESHOCKABSORBERAPARTORTODOANYMAINTE – NANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 4 CONNECTION (15 MM )

Incoming search terms:

KTM KINETO TRACKING MOUNT – MODEL K433 Installation and Removal Manual

0

Filed Under (KTM) by admin on 30-01-2012

download
the KTM meets the needs of a wide variety of test range and scientific applications:  On-board operator, or remote analog or digital control  Payloads up to 1200 pounds (unmanned) or 600 pounds (manned)  Mission configuration with four (manned) or six (unmanned) payload positions  Complete turnkey systems available  Detailed installation documentation FIELD-PROVEN RUGGED AND RELIABLE The KTM consistently demonstrates its performance and durability:  Weather tight seals designed to withstand harsh range environments  The KTM’s direct drive axis design delivers smooth, jitterfree tracking to ensure precise Time, Space and Position Information (TSPI)  Self-contained and trailer-mounted, the KTM is quickly and easily deployed via highway and unimproved roads to remote tracking sites  Digital Control System (DCS) that guarentees system reliability WHEN THE RANGES REQUIRED PRECISE AND RELIABLE OPTICAL TRACKING MOUNTS, THEY SELECTED THE BRASHEAR KINETO TRACKING MOUNT MORE THAN 150 TIMES. Recognized Standard for Tracking Systems Worldwide THE KTM DIGITAL CONTROL SYSTEM (DCS) INCLUDES:  High speed communication via an Ethernet interface to provide remote operation  Advanced servo loop control to optimize tracking performance  Built-in error correction to ensure precision tracking accuracy  Versatile chassis architecture that accommodates additional PC104 cards suchas an “Automatic Video Tracker” (AVT) to satisfy specific customer requirements and missions

Incoming search terms:

2009 GAS GAS TXT PRO TECHNICAL SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Gas Gas) by admin on 28-11-2010

download
ENGINE 2 stroke, single cylinder, direct reed valve crankcase induction. Liquid cooled. 125 cc. engine Cylinder size 124,8 cc. Bore and stroke 54 x 54.5 mm. 200 cc. engine Cylinder size 175,3 cc. Bore and stroke 64 x 54,5 mm. 250 cc. engine Cylinder size 247,7 cc. Bore and stroke 72,5 x 60 mm. 280 cc. engine Cylinder size 272,2 cc. Bore and stroke 76 x 60 mm. 300 cc. engine Cylinder size 294,1 cc. Bore and stroke 79 x 60 mm. Carburettor, diameter of the diffusor 26 Lubrication system Mixture (50:1)(2%) Ignition system Digital magnetic flywheel CDI TRANSMISSION Transmission type 6 gears, Four / Six system by GAS GAS* (Patented). Clutch type Hydraulic command, 1/3 discs, variable progressive with diaphragm system by GAS GAS* (Patented). Driving system By chain Gear ratio 1st. 2,996 (35x27x28/16x24x23) 2nd. 2,571 (36/14) 3th. 2,187 (35/16) 4st. 2,112 (36x23x24/14x28x24) 5st. 1,125 (27/24) 6th. 0,821 (23/28)
-11- Primary reduction ratio 2,777 (75/27) Final reduction ratio 3,818 (42/11) Overall drive ratio 8,704 (6th. gear) Transmission oil Capacity 550 cc. Type 10W40 API SF o SG. FRAME Type Tubular profile made with Cr-Mo. Tyres Front 2,75 x 21″ Trial Rear 4,00 x 18″ Trial tubeless. Suspension Front Adjustable tele-hydraulic fork ø 40 mm. (125 / 200). Adjustable tele-hydraulic fork ø 40 mm with aluminium bars (250 / 280 / 300) Rear Variable progressive system with mono-shock multiadjustable. Suspension stroke Front 177 mm. Rear 164 mm. Front fork oil SAE 5. Front fork oil level ø 40 mm.(125 / 200) 180 mm. air chamber steel bar ø 40 mm. (250 / 280 / 300) 160 mm. air chamber aluminium bar BRAKES Type Disc brake. Disc diameter Front ø185 mm. 4 piston calipers. Rear ø150 mm. 2 piston calipers. DIMENSIONS Overall height 1180 mm. Overall width 820 mm. Seat height 650 mm. Ground clearance 315 mm. Wheelbase 1330 mm. Fuel tank capacity 3,1 liters.

Incoming search terms:

Incoming search terms: