ktm bendix starter motor

You search Auto repair manual PDF ktm bendix starter motor, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ktm bendix starter motor Direct Download speed 5282 Kb/s

  ktm bendix starter motor Full Version speed 6162 Kb/s



KTM Starter Gear Maintenance Instructions

0

Filed Under (KTM) by admin on 26-11-2010

download
Checking the electric starter motor for wear -Check Bendix 1 for smooth operation and signs of wear. -Check the sprocket of the electric starter for wear and radial clearance. -Replace O-ring 2 of the electric starter. -Replace gasket 3 . -Check starter idler gear 4 for smooth operation and wear, check that the bearing bushings are seated firmly. Electric starter motor – checking for and adjusting play -Mount the electric starter and the starter idler gear. -Mount the tighten cover 5 . -Move starter idler gear 4 back and forth in the direction of rotation, the maximum play may not exceed half the width of a tooth. -If play is larger, cover 5 must be removed and as many shims 6 with a thickness of 0.10 mm as necessary must be added to eliminate all play. Then remove one shim again. -Check the play again; the maximum play may not exceed more than half of the width of a tooth. 1 2 3 4 5 4 5 6

Incoming search terms:

HARLEY DAVIDSON XL STARTER MOTOR COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation 1. Remove exhaust system according to Service Manual instructions. 2. See Figure 1. Remove the outer primary screw shown and retain it for reinstallation. 3. See Service Parts Illustration. Insert the thread cleaning screw (9), through the primary cover and the crankcase until the full screw diameter protrudes through the crankcase. Remove any debris from from the tip of the thread cleaning screw. Remove thread forming screw and discard. NOTE If thread cleaning screw binds in crankcase hole, remove thread cleaning screw and chase threads with 1/4 – 20 tap. 4. Install set screw (8) from outer primary side using the wrench provided. Set screw should extend past the crankcase approximately .375″. 5. With wrench in set screw to prevent rotation, install the backplate over the set screw and fasten with the 1/4-20 nylock nut (5). 6. Reinstall the primary cover screw saved in Step 1. Torque to 80-110 in-lbs (9-12 Nm). 7. Remove the the oil hose clamp from the starter stud. Do not remove the clamp from the hoses. 8. Replace the original equipment starter stud with stud (7) provided. Torque to 39-65 in-lbs (4-7 Nm). 9. Install bracket (2) over stud (7) and fasten with #10-24 nylock nut (6). Rotate bracket until the tab on the bracket rests on starter motor. 10. Install oil hose clamp onto bracket (2) using one of the #10-24 screws (4). Tuck the hoses down as far as possible without contacting the drive belt or kinking the hose. Contacting the drive belt or kinking the hose may cause damage to the hoses or powertrain. 11. Install the cover (1) to the backplate (3) and bracket (2) using four of the #10-24 screws (4) with the wrench provided. The cover should fit inboard of the gear cover and partially on top of the sprocket cover. Start the bracket screw first, then follow with the (3) backplate screws. 12. Reinstall exhaust system according to Service Manual Instructions

Incoming search terms:

2006 KTM 250 SX-F 250 EXC RACING 400 EXC RACING 450 SX, XC, EXC RACING 525 SX, XC, EXC RACING, REPAIR MANUAL

0

Filed Under (KTM) by admin on 05-05-2012

download
Hot start lever (250 SX-F) If you pull the red hot start lever [1] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a „lean” fuel-air mixture of the type needed for hot starts.
ENGLISH 7 OPERATION INSTRUMENTS » Headlamp switch (EXCUSA) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button (EXC) Pushing the black starter button [2] will actuate the E-starter. Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 2 3 4 5 6 Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on

Incoming search terms:

2007 KTM 250 XC-F, XCF-W, EXC-F 400 XC-W, EXC RACING 450 XC, XC-W, EXC RACING 525 XC, XC-W, EXC RACING 525 XC DESERT RACING INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 05-02-2012

download
Headlamp switch (XC-W) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button Pushing the black starter button [2] will actuate the E-starter. Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on. ENGLISH 7 2 Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 3 4 5 6 1 OPERATION INSTRUMENTS » ENGLISH 8 TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode

Incoming search terms:

2008 KTM 250 SX-F 250 XC-F, XCF-W 250 EXC-F, EXC-F SIX DAYS INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 22-10-2010

download
Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). 1 A Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. 2 Headlamp switch (XCF-W) In this model the headlamp is switched on with the pull switch [5] . 5 Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right
OPERATION INSTRUMENTS » ENGLISH 7 1 2 3 4 5 Starter button Pushing the red starter button [1] will actuate the E-starter. Emergency OFF switch (EXC-F Australia) The red emergency-OFF switch [2] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [3] will actuate the E-starter. Indicator lamps The green control lamp [4] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [5] lights up when the high beam is on. TEST All of the display segments briefly light up for the display function test. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions

Incoming search terms:

1995 Camry WIPER MOTOR CIRCUIT BREAKER INSPECTION PROCEDURE

0

Filed Under (Toyota Manuals) by admin on 15-10-2011

download
INSPECTION PROCEDURE: Inspect the Wiper Fuse. Verify there is power and ground to the Wiper Motor on all speeds (including “Intermittent” or “Mist” if applicable). After verifying power and ground to the Wiper Motor, follow the procedure below to prevent unnecessary Wiper Motor replacement because of a temporary open in the Wiper Motor Circuit Breaker. 1) Disconnect the Wiper Motor Harness Connector. 2) Wait (10) minutes before checking continuity. 3) Check the continuity of the motor with an ohmmeter. REPRESENTATIVE CHECKING PROCEDURE: NOTE: Continuity check can be performed between either the low speed or high speed terminal and the ground terminal of the wiper motor. The standard resistance of a good wiper motor is approximately 1.5 to 4.5 ohm

Incoming search terms:

KTM ATV 525 XC specification

0

Filed Under (KTM) by admin on 12-11-2010

download
Engine ] Pure power for Enduro enthusiasts. The power of the 525 XC is the indisputable benchmark in the ATV Enduro sector. Its acceleration and top speed cast a shadow over all its predecessors. Variable ignition curves and perfect maintenance features like simple valve play adjustment and the removable clutch cover are even further highlights of the XC engine that make the KTM Enduro quads so superior. First Oil Filling for all KTM Engines. [ CarburEttor ] The Keihin carburettor, which has been proven multiple times in racing, with 39 mm and the Throttle Positioning System guarantees a uniform, forceful power delivery in all speed ranges. It ensures an unrivalled response behavior and perfect service-friendliness at all times. [ StartEr ] Packed in a space-saving manner into the free space behind the cylinder head, the small, light electric starter motor is ready for use. It brings every KTM ATV up to speed reliably and comfortably even when racing becomes hectic. [ rEar SuSPENSIoN ] Premium-quality ÖHLINS suspension components specially designed for tough Enduro use are provided as standard – both at the front and the rear. Easy to adjust, they guarantee optimal tuning for the most varied of terrains. Another highlight: the front and rear spring travel of 275 mm and 272 mm respectively is 100 % trend-setting for an Enduro ATV! [ alumINIum SubFramE ] The rear subframe is made of aluminium and is extremely light and easy to remove. [ FramE ] The lightweight, extremely durable frame sets the benchmark in the quad racing segment and is made of high-strength, powder-coated Chromoly steel. [ haNDlEbar ] An ultra-durable tapered aluminium Magura® handlebar comes standard that is four-position adjustable to suit your preferred ergonomics. Further highlights are the functional and individually adjustable operating levers for brake and hydraulic clutch. In addition, the chassis has an integrated mount for a steering damper – available as a PowerPart accessory. [ CurvED raDIator ] Best cooling by means of its curved shape and the resulting maximized surface area. [ rImS / tIrES ] MAXXIS Razr tyres on light, stable DWT aluminium rims. [ ExhauSt ] The powerful XC silencer is made of light-weight aluminium.

Incoming search terms:

Commonwealth of Massachusetts Registry of Motor Vehicles Motorcycle Manual

0

Filed Under (Tips and Review) by admin on 18-11-2010

download
DEFINITIONS MOTORCYCLE Any motor vehicle having a seat or saddle for the rider that is designed to travel with no more than three wheels contacting the ground, including any bicycle with a motor or driving wheels attached. MOTORIZED BICYCLE A pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty (30) miles per hour (mph) . OPERATION OF MOTORIZED BICYCLES Under Massachusetts law, mopeds fall into the category of “motorized bicycles”(with or without pedals) and are therefore regulated by the Registrar of Motor Vehicles. Individuals must have a valid learner’s permit or driver’s license to operate a motorized bicycle or moped. Mopeds must have automatic transmissions and cylinder capacities of no more than 50 cubic centimeters. In addition, mopeds must meet all federal motor vehicle safety standards and have maximum speeds of no more than 30 mph. The following limitations apply:  Individuals may not operate at speeds greater than 25 mph;  Individuals may not operate on state highways or limited- access roads with signs prohibiting bicycles;  Individuals may not operate on off-street recreational paths;  Individuals may use bicycle lanes along roadways;  Individuals must use the proper hand signals before stopping or turning;  Individuals and their passengers must wear United States Department of Transportation (US DOT) approved helmets when operating;  Individuals may not carry passengers while operating on a permit.

Incoming search terms:

KTM KINETO TRACKING MOUNT – MODEL K433 Installation and Removal Manual

0

Filed Under (KTM) by admin on 30-01-2012

download
the KTM meets the needs of a wide variety of test range and scientific applications:  On-board operator, or remote analog or digital control  Payloads up to 1200 pounds (unmanned) or 600 pounds (manned)  Mission configuration with four (manned) or six (unmanned) payload positions  Complete turnkey systems available  Detailed installation documentation FIELD-PROVEN RUGGED AND RELIABLE The KTM consistently demonstrates its performance and durability:  Weather tight seals designed to withstand harsh range environments  The KTM’s direct drive axis design delivers smooth, jitterfree tracking to ensure precise Time, Space and Position Information (TSPI)  Self-contained and trailer-mounted, the KTM is quickly and easily deployed via highway and unimproved roads to remote tracking sites  Digital Control System (DCS) that guarentees system reliability WHEN THE RANGES REQUIRED PRECISE AND RELIABLE OPTICAL TRACKING MOUNTS, THEY SELECTED THE BRASHEAR KINETO TRACKING MOUNT MORE THAN 150 TIMES. Recognized Standard for Tracking Systems Worldwide THE KTM DIGITAL CONTROL SYSTEM (DCS) INCLUDES:  High speed communication via an Ethernet interface to provide remote operation  Advanced servo loop control to optimize tracking performance  Built-in error correction to ensure precision tracking accuracy  Versatile chassis architecture that accommodates additional PC104 cards suchas an “Automatic Video Tracker” (AVT) to satisfy specific customer requirements and missions

Incoming search terms:

2001 YAMAHA TDM900 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 20-11-2010

download
CHECKING THE SWITCHES ELEC EAS00731 ELECTRICAL CHECKING THE SWITCHES Check each switch for damage or wear, proper connections, and also for continuity between the terminals. Refer to “CHECKING SWITCH CONTINUITY”. Damage/wear Repair or replace. Improperly connected Properly connect. Incorrect continuity reading Replace the switch. -3- ELECTRIC STARTING SYSTEM ELEC EAS00755 ELECTRIC STARTING SYSTEM CIRCUIT DIAGRAM -4- ELECTRIC STARTING SYSTEM ELEC 4 Main fuse 5 Battery 7 Starter relay 8 Starter motor 9 Main switch 12 Starting circuit cut-off relay 13 Sidestand switch 14 Neutral switch 49 Clutch switch 59 Engine stop switch 60 Start switch 61 Ignition fuse -5- ELECTRIC STARTING SYSTEM ELEC EAS00756 STARTING CIRCUIT CUT-OFF SYSTEM OPERATION If the engine stop switch is set to “” and the main switch is set to “ON” (both switches are closed), the starter motor can only operate if at least one of the following conditions is met: The transmission is in neutral (the neutral switch is closed). The clutch lever is pulled to the handlebar (the clutch switch is closed) and the side- stand is up (the sidestand switch is closed). The starting circuit cut-off relay prevents the starter motor from operating when neither of these conditions has been met. In this instance, the starting circuit cut-off relay is open so current cannot reach the starter motor. When at least one of the above conditions has been met the starting circuit cut-off relay is closed and the engine can be started by pressing the starter switch. WHEN THE TRANSMISSION IS IN NEUTRAL WHEN THE SIDESTAND IS UP AND THE CLUTCH LEVER IS PULLED TO THE HANDLEBAR 4. Starting circuit cut-off relay Disconnect the starting circuit cut-off relay from the wire harness. Connect the pocket tester (Ω 1) and battery (12 V) to the starting circuit cut-off relay terminals as shown. YES NO Replace the starting circuit cut-off relay. Does the starting circuit cut-off relay have continuity between blue/white and black? EAS00759 Continuity Tester positive probe sky blue Tester negative probe blue/yellow No conti- nuity 1 2 1 3 Tester positive probe sky blue Tester negative probe black/yellow Battery positive terminal red/black Battery negative terminal black/yellow 1 2 Tester positive prove blue/white Tester negative prove black 3 4 5. Starting circuit cut-off relay (diode) Disconnect the starting circuit cut-off relay from the wire harness. Connect the pocket tester (Ω 1) to the starting circuit cut-off relay terminals as shown. Measure the starting circuit cut-off relay for continuity as follows. Tester positive probe blue/green Tester negative probe blue/yellow 4 3 Tester positive probe black/yellow Tester negative probe sky blue 2 1 Tester positive probe blue/yellow Tester negative probe sky blue 3 1 Tester positive probe blue/yellow Tester negative probe blue/green 3 4 When you switch the tester’s positive and negative probes, the readings in the above chart will be reversed. Are the testing readings correct? YES NO Replace the starting circuit cut-off relay. NOTE: EAS00760

Incoming search terms:

Incoming search terms: