kymco mxu 500 spark plug location

You search Auto repair manual PDF kymco mxu 500 spark plug location, if there are search results will appear below. If search results do not exist, please search by others keyword.



  kymco mxu 500 spark plug location Direct Download speed 5282 Kb/s

  kymco mxu 500 spark plug location Full Version speed 6162 Kb/s



SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

SANYANG HD 125/ 200 Specifications And SERVICE MANUAL

0

Filed Under (Sym) by admin on 24-11-2010

download
heck and adjustment Fault condition Probable causes Loosen carburetor drain bolt to check if there is gasoline inside the carburetor Fuel supplied tom carburetor sufficient No fuel is supplied to carburetor Remove spark plug, install it into spark plug cap, and perform a spark test against engine ground. Perform cylinder compression pressure test. Check if sparks Weak sparks, no spark at all Low compression pressure or no pressure Re-start by following the starting procedures No ignition There are some signs of ignition, nut engine can not be started Remove the spark plug again and check it. Remove carburetor after 30 minutes and connect a hose onto fuel rich circuit. Then blow the hose with air Dry spark plug Wet spark plug Blowing in normal Blowing clogged 1. No fuel in fuel tank 2. Check if the pipes, fuel tank to carburetor and intake vacuum, are clogged. 3. Float valve clogged 4. Lines in fuel tank evaporation system clogged 5. Malfunction of fuel pump 6. Loosen or damaged fuel pump vacuum hose 7. Fuel filter clogged 1. Malfunction of spark plug 2. Spark plug foul 3. Malfunction of CDI set 4. Malfunction of AC generator 5. Ignition coil is in open or short circuit 6. Ignition coil leads open or short circuit 7. Malfunction of main switch 1. Piston ring seized 2. Malfunction of cylinder valves 3. Worn cylinder and piston ring 4. Cylinder gasket leak 5. Sand hole in compression parts 1. Malfunction of throttle valve operation 2. Air sucked into intake manifold 3. Incorrect ignition timing 1. Fuel level in carburetor too high 2. Malfunction of throttle valve operation 3. Throttle valve opening too wid

KYMCO MXU 500 SPECIFICATION AND OWNER'S MANUAL

0

Filed Under (Kymco) by admin on 12-11-2010

download
OFF ON (1) CONTROL FUNCTIONS 17 (1) Ignition switch (2) Key IGNITION SWITCH ON: Functions oft he respective switch positions areas follows: The key cannot be removed. Theenginecanbe started. OFF: “”: All electrical circuits are switched off except hazard light. The key can be removed in this position. All electrical circuits are switched on. The ignitions witch is ON while the position light and taillightwill light. All electrical circuits are switched on. Theenginecanbe started. The key cannot be removed. 18 INSTRUMENTS AND INDICATOR (1) Multi-function display (2) (3) (5) (6) Low-range indicator light”L” (7) High-range indicator light”H” (8) Neutral indicator light”N” (9) Reverse indicator light”N: (10) Park indicator light”P” (11) (12) Right turn signal indicator High beam indicator (4) Coolant temperature warning indicator Set button Mode button Left turn signal indicator (11) (2) (3) (4) (5) (8) (1) Multi-function display The display includes the following functions: Speedometer Odometer/Tripmeter Digital clock 2WD/4WDindicator Fuel gauge (2) Right turn signal indicator Flashes when the right turn signal operates. (3) High beam indicator The ignition switch is at the”"position, the high beam indicator will light when the headlight switch to select High beam () . Both left and right turn signal indicator will flash at the meantime when the hazard switch is operated and turn signal switch is turned off. NOTE: (12) (1) (7) (6) (9) (10) TRIP ODO mile kmPM 2WD 4WD SET MODE PRNHL
19 (4) Coolant temperature warning indicator When the coolant temperature reachesa specified level, this indicator comes onto warn that the coolant temperature is too hot. If the indicator comes on during operation, stopt he engine as soon as it is safe to do so and allow the engine to cooldown for about 10 minutes. (5) Set button This button is used to select ODO, TRIP A andT RIPB. This button is also used to adjust the time and reset the tripmeter. (6) Low-range indicator light”L” This indicator light comes on when the drive select lever is in the”L”position. (7) High-range indicator light”H” This indicator light comes on when the drive select lever is in the”H”position. (8) Neutral indicator light”N” This indicator light comes on when the drive select lever is in the”N”position

Incoming search terms:

HARLEY DAVIDSON V-Series California Engine Owner's Manual

0

Filed Under (Harley Davidson) by admin on 28-11-2010

download
During Break-In At 50 Miles (80 Kilometers): 1- Change engine oil and filter. 2- Inspect for fuel and oil leaks. 3- Inspect air cleaner element and service as required. 4- Check tightness of exterior fasteners, except head bolts. Engine Maintenance at 500 Miles (800 Kilometers): 1- Change engine oil and filter. 2- Inspect for fuel and oil leaks. 3- Inspect air cleaner element and service as required. 4- Check tightness of exterior fasteners, except head bolts. 5- Check operation of enrichment device and throttle controls. 6- Check engine idle speed. 7- Check tightness of engine mounts. Regular Service Intervals Regular lubrication and maintenance will help keep your new S&S engine operating at peak performance. The following table presents the required service schedule for normal operating conditions. Failure to complete the required engine maintenance can result in engine damage and an increase in emissions. Please refer to the motorcycle owner’s manual for any additional required chassis maintenance. Engine Service Intervals Item Interval Engine Oil & Filter Change at 50, 500, 2,500 miles (80, 800, 4,000 kilometers), every 2,500 miles (4,000 kilometers) thereafter1 Air Cleaner Element Inspect at 50 and 500 miles (80 and 800 kilometers), every 2,500 miles (4,000 kilometers) thereafter2 Tappet Oil Screen Inspect every 2,500 miles (4,000 kilometers). Replace every 5,000 miles (8,000 kilometers). Petcock, Lines, & Fittings, Vacuum Lines Inspect at 50 and 500 miles (80 and 800 kilometers), every 2,500 miles (4,000 kilometers) thereafter. Fuel Tank Filter Screen & In-Line Fuel Filter (If used) Inspect every 5,000 miles (8,000 kilometers). Engine Idle Speed Adjust as required. Operation of Throttle & Enrichment Device ControlsInspect at 500 miles (800 kilometers) and every 2,500 miles (4,000 kilometers) thereafter. Spark Plugs Inspect every 5,000 miles (8,000 kilometers). Replace every 10,000 miles (16,000 kilometers) or as needed. Ignition Timing Inspect every 5,000 miles (8,000 kilometers). Engine Mounts Inspect at 500 miles (800 kilometers) and every 5,000 miles (8,000 kilometers) thereafter. External Fasteners Except Engine Head Bolts Re-torque at 500 miles (800 kilometers) and every 5,000 miles (8,000 kilometers) thereafter. 1- S&S recommends that petroleum-based oil not specifically formulated for motorcycles should be changed every 1,000 miles (1,600 kilometers) after the break-in period. 2- Replace more frequently if required or if engine is operated in a dusty environment.

Incoming search terms:

Honda VT1100 Shadow Guide Plug Patch Repair Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
Find the guide plug.bn The guide plug is shown in the shop manual with the engine removed from the frame and the left crankcase cover removed. (You’ll find this illustration in the “ELECTRIC STARTER/STARTER CLUTCH” chapter in the “STARTER DRIVEN GEAR/STARTER CLUTCH REMOVAL” section.) It’s a little bit harder to find it on the bike. Start by following the yardstick to see where the guide plug is on my bike. To find it on your bike, lie on the ground (or, preferably a mechanics creeper) next to the bike (without the yardstick) and peek under the shift lever and over the frame There it is, just barely visible from the side of the bike. Here’s what a new one looks like: 2. Clean the guide plug and crankcase. From the front of the bike, clean the guide plug and crankcase with brake cleaner in a VERY focused spray. Let the cleaner evaporate before moving to the next step. Page 4 Rev: Draft 5/20/2007 Page 4 of 5 3. Reposition the guide plug. a. From the side of the bike, use the yardstick (or a long screwdriver if you prefer) to gently push the guide plug back into the crankcase. (Note the JB Weld from the previous patch operation.) b. From the front of the bike, gently push upward on the bottom of the upper tab (as shown below) or the bottom of the forward tab to rotate the guide plug into the proper position while maintaining pressure with the yardstick

Incoming search terms:

Kymco MXU 250 WINCH MOUNTING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kymco) by admin on 26-10-2010

download
Begin by placing winch in freespool. Support the winch so that it will stand upright on the workbench, Fig. 1. This will ensure that the winch drivetrain will not be dislocated during disassembly. 2. Remove the two lower cap screws and nuts. Next remove the two upper cap screws, Fig. 2. Figure 2: Remove Cap Screws Figure 1: Position the Winch Upright Lower Cap Screws Upper Cap Screws Freespool Lever Position 3 Lift the gear housing straight up off the gears. Take care not to disturb the gear set. 4. Rotate the gear housing clockwise 90 degrees and place back down over the gear set. It may take slight twisting motion to have the housing align and drop over the gear set. 5. Align holes and replace hardware securing the endhousing back on the winch. Torque bolts to 45 in-lbs. The winch is now ready to be installed. Figure 3: Lift Gear Housing Figure 5: Reinstall Hardware Figuere 4: Rotate and Replace Gear Housing Rotate and Lower IV. Kymco MXU 250 Installation 1. Begin by removing the plastic bumper located on the front of the ATV. Remove the four front bolts and two bolts securing the bumper on the back side, Fig. 6. 2. Set the bumper aside. Save the fasteners to reinstall the bumper.

Incoming search terms:

HARLEY DAVIDSON GLOSS BLACK HEAD BOLT COVERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
This kit fits 1992 and later Evolution 1340 and XL models and 1999 and later Twin Cam-equipped models. INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Remove spark plugs. 2. See Figure 1. Install head bolt covers (1), on head bolts (3), secure using setscrew (2) and Allen wrench included with kit. To prevent setscrews from falling into the spark plug holes, start threading the setscrews into the covers before placing them over the head bolts. Position cover on head bolt so that when spark plug is reinstalled setscrew is hidden from view but accessible with Allen wrench. Do not tighten setscrews on high points of bolts. 3. Reinstall spark plugs. Tighten spark plugs to 11-18 ftlbs (15-24 Nm) . If a torque wrench is not available, finger- tighten spark plug and then, using a spark plug wrench, tighten plug an additional 1/4 turn. 4. Readjust setscrew tightness after motor has operated at full operating temperature and then cooled. 2 1 3 is 001586 1. Head bolt cover 2. Setscrew 3. Head bolt Figure 1. Head Bolt Cover Installation

Incoming search terms:

KYMCO MXU 300/ 250 SPECIFICATION AND OWNER'S MANUAL

0

Filed Under (Kymco) by admin on 12-11-2010

download
FRAMES ERIAL NUMBER The frames erial number is stamped on the front oft he frame. (1) Frame serial number (2) Engine serial number 11 (1) (2) (01) Rear brake lever (03) Front brake lever (04) Right front turn signal light (02) Headlights/Position lights (05) Steering handlebar lock (06) Left front turn signal light 12 PARTS LOCATION (01) (02) (02) (03) (04) (05) (06) (07) Right rear turn signal light (08) Ta illights/Stoplights (11) Exhaust system (12) Trailer hitch (13) License light (14) Battery (09) Instrument and indicators (10) Left rear turn signal light (09) (08) (08) (10) (07) 13 (14) (13) (11) (12) 14 (15) Drive select lever Tool kit (19) Reservoir water tank (20) Brake pedal fluid reservoir (16) Fuel valve (17) Seat (18) (16) (15) (18) (17) (19) (20) 15 (21) ) Choke knob (23) Recoil starter Exhaust system (22 (23) (22) (21) (24) Front brake lever ) Front cargo rack (26) Front brake fluid reservoir (27) Ignition switch (28) Rear (29) Accessory socket seat (30) Rear brake lever (31) (32) Leftfootpeg /Parking brake (25 brake fluid reservoir Headlight dimmer switch Starter button Hazard switch Turn signal switch Horn switch (33) Fuel fill cap (34) Throttle lever (35) Rightfootpeg (36) Rear brake pedal 16 (33) (34) (32) (31) (35) (36) (24) (25) (26) (27) (28) (29) (30) NOTE: Themachineyou have purchased may differ slightly from those shown in the figures of this manual. (37) Rear cargo rack ) Flagpole bracket (38

Incoming search terms:

HONDA CB650/ 750F/ 900F/ 1100F/ GL1100 Spark Unit Set Installation Manual

0

Filed Under (Honda) by admin on 05-04-2011

download
INSTALLATION INSTRUCTIONS: 1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the seat and/or petrol tank to gain access to the original spark units (if fitted); these are normally fitted under the seat between the top frame tubing. Each of these units consists of a small alloy metal box with sleeved wires terminated by a small connector (coupler). They also have a mounting tab with a single fixing hole. 3. On four cylinder machines there will be two units, normally mounted back to back; one for cylinders 1&4 and one for cylinders 2&3. 4. For safety, disconnect the battery. 5. Unplug the couplers from each of the units. Undo the fixings and remove the units. 6. Fit the new spark units in the place of the old ones or find a suitable alternative, close to the connectors. Secure the units to the frame or mounting platform using the supplied tie-straps and adhesive mounting base (if required). If required, a thin sheet of rubber or double-sided tape can be used to keep the units in position. Do not completely wrap the units in foam rubber. 7. Push the wiring harness plugs into the new spark unit socket connectors; they will only fit one way. Reconnect the battery. 8. If you are rewiring the machine or do not have the standard wiring harness, the spark unit wire colours & functions are as follows: GREEN Ö GROUND (0 VOLTS) BLACK/WHITE Ö IGNITION SUPPLY (+12 VOLTS) VIA ENGINE STOP SWITCH YELLOW Ö IGNITION COIL OUTPUT (TO COIL —) WHITE Ö PULSE GENERATOR (WHITE RING) BLUE Ö PULSE GENERATOR (UNMARKED) There are two pulse generators, one for cylinders 1&4 and one for cylinders 2&3. The left hand one is normally for cylinders 1&4 (see fig.1). There are two wires of the same colour coming from each pulse generator, one of these wires is normally marked with a white band. The pulse generator wire with the white band connects to the white wire from the corresponding spark unit, the other pulse generator wire connects to the blue wire on the corresponding spark unit. If the white band is missing, this is normally the upper wire coming from the pulse generator. 9. Refit the seat and tank (if removed earlier). 10. Fitting is now complete, although for best results you may wish to verify the ignition timing, see the following guide

Incoming search terms:

KYMCO MXU 375 ATV WINCH MOUNT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kymco) by admin on 26-10-2010

download
WINCH MOUNT INSTALLATION INSTRUCTIONS 1. Remove molded plastic bumper guard from the ATV. 2. Mount the winch mount weldment (Item 1) to the ATV as shown below. 3. Mount the roller hawse to the winch mount weldment as shown above. 4
4. Mount the winch to the winch mount weldment and route the winch cable through the rollers. (Installer may need to remove rollers to allow cable end to pass through). 5. Wire the winch according to the manufacturer instructions. 6. Re-install the molded plastic bumper guard. 5 *CAUTION BE AWARE OF WHEN THE CABLE STOP CONTACTS THE ROLLER HAWSE AS CABLE IS WOUND IN. FAILURE TO RELEASE MAY CAUSE DAMAGE TO WINCH PARTS OR TO THE ATV. When using the winch to raise and lower a blade a cable stop must be installed. Carefully raise the blade until the top of the push tube’s are no closer than 1″ anywhere on the ATV. Place the Cable Stop onto the Winch Cable up against the Winch Hawse. Secure the Cable Stop to the Winch Cable using the Cable Clamp Assembly as shown in the pictures below.

Incoming search terms:

Incoming search terms: