le ft handed thread on compe nsator sprocket 2002 harley

You search Auto repair manual PDF le ft handed thread on compe nsator sprocket 2002 harley, if there are search results will appear below. If search results do not exist, please search by others keyword.



  le ft handed thread on compe nsator sprocket 2002 harley Direct Download speed 5282 Kb/s

  le ft handed thread on compe nsator sprocket 2002 harley Full Version speed 6162 Kb/s



HARLEY DAVIDSON CHROME BELT SPROCKET COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation 1. Remove rear wheel. Refer to the applicable Service Manual for the proper removal procedure. 2. Remove bolts and washers from sprocket. •If you intend to install Acorn Nut and Stud Kit (Part No. 91734-85), refer to that Instruction Sheet at this time (please note that this Acorn Nut and Stud Kit does not fit Sportster (XL) models). •If you do not intend to install Acorn Nut and Stud Kit (Part No. 91734-85), retain bolts and washers for reassembly. Proceed to Step 3. 3. Position sprocket cover so that its mounting holes align with the holes in the sprocket. NOTE There is only one position which allows each hole in the cover to align with a hole in the sprocket. If replacement bolts, washers, or nuts are required, use only genuine Harley-Davidson parts specified for your particular model. Aftermarket fasteners can adversely affect performance, which could result in death or serious injury. NOTE • See Harley-Davidson service manual for proper torque val- ues; •Aftermarket fasteners may not have the specific property requirements to perform properly. 4. Install bolts with washers through holes in sprocket cover and sprocket, and into threaded holes in wheel hub. Depending on the tensile strength grade of the bolts in your particular application, tighten bolts in a crosswise pattern to one of the torque values listed in the following table: 5. Refer to the applicable Service Manual for the proper procedure and perform the following: •Install axle. •Align belt. •Adjust belt tension. •Tighten rear axle nut to 60 – 65 ft-lbs torque. 6. Check sprocket for radial runout (eccentricity). If runout is visible, mark outer edge of sprocket at the location of runout. Loosen sprocket bolts and tap the marked location with a rubber mallet. Tighten sprocket bolts in a crosswise pattern to the applicable torque specified in Step 4.

Incoming search terms:

HARLEY DAVIDSON DYNA SPROCKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
1991-1992 Dyna models: Screw (5) 3739A 1993-1995 FXDL, 1995 FXD and FXDS, all 1997-1999 Dyna models: Screw (5) 3730A 1993-1995 FXDWG and all 1996 Dyna models: Screw (5) 3769 1991-2005 Dyna models: Washer (5) 6516HW 2000-2006 Dyna models: Screw, with lock patch (5) 3737A 2006 Dyna models: Screw, with lock patch (5) 3873 2007 and later Dyna models: Screw, with lock patch (5) 3109 The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) Kit Contents There are no Service Parts available with this kit. INSTALLATION NOTES The cotter pin or spring clip for the rear axle nut must be replaced during assembly and is available for purchase from a Harley-Davidson dealer. The five sprocket mounting screws must be replaced when replacing the sprocket. Remove existing sprocket according to service manual instructions. Remove all residual threadlocking agent from fastener holes using an appropriate thread chasing device and compressed air.

Incoming search terms:

HARLEY DAVIDSON CHROME SPROCKET HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
INSTALLATION For 1991 through 1996 XL with Laced Wheels For 1993 through 1996 Softail with Laced Wheels For 1993 through 1997 Dyna with Laced Wheels 1. Remove the rear wheel. Refer to REAR WHEEL REMOVAL in the Service Manual. 2. Remove all stock sprocket mounting screws, washers and locknuts. 3. Place a new chrome washer onto the threads of each new chrome screw from the kit. Install the sprocket onto the wheel. 4. See Figure 1. Obtain new original equipment locknuts and install on the screws. See Figure 2. Tighten all screws in the sequence shown to 45-55 ft-lbs (61-75 Nm). 5. Install the rear wheel. See REAR WHEEL INSTALLATION in the service manual. Verify the correct axle alignment and check belt deflection per service manual instructions INSTALLATION For 1997 and Later XL with Laced Wheels For 1997 through 1999 Softail with Laced Wheels For 1998 through 1999 Dyna with Laced Wheels For ALL Models with Cast Wheels 1. Remove the rear wheel. Refer to REAR WHEEL REMOVAL in the Service Manual. 2. Remove all stock sprocket mounting screws and washers. 3. Place a new chrome washer onto the threads of each new chrome screw from the kit. Apply 2-3 drops of Loctite 262 (red) to the screw threads, and install the sprocket onto the wheel. Tighten all sprocket screws finger-tight. 4. See Figure 3. Tighten the bolts in the sequence shown to 23 ft-lbs (31.2 Nm). NOTE If 23 ft-lbs (31.2 Nm) is reached before screw is fully seated, remove screw and examine screw and wheel for thread damage. Replace screw or wheel if threads are damaged. 5. After all screws have been tightened to 23 ft-lbs (31.2 Nm), mark a straight line, with a grease pencil, on all sprocket screw heads continuing the line over onto the sprocket. 1 4 2 5 3 30 is04009 Figure 3. Tightening Sequence (Later Laced Wheels and All Cast Wheels) 6. Mark a second line at 30° clockwise from the lines on the sprocket at each screw. NOTE For best results, use Snap-on Torque Angle Gauge TA360 or equivalent. 7. Using the marks as a guide, and using the tightening sequence shown in Figure 3+, turn each screw an additional 1/12 turn or 30° clockwise. 8. Install the rear wheel. See REAR WHEEL INSTALLATION in the service manual. Verify the correct axle alignment and check belt deflection per service manual instructions

Incoming search terms:

Harley-Davidson BAKER COMPENSATING SPROCKET INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-04-2012

download
1) Remove the primary chain case cover. Refer to your Factory Service Manual for this procedure. 2) Remove the compensating sprocket nut with a 1-1/2″ socket. A ½” impact gun is best for this task. *) Remove the 1-3/16″ clutch nut. This is a left handed nut so loosen it by turning it in the clockwise direction (as viewed from the left side of the motorcycle). 4) With one hand on the compensating sprocket and one on the clutch assembly, remove the primary drive assembly (compensating sprocket, primary chain, tensioner assembly, and clutch as shown in figure a and set it on a clean surface. 5) Flip the adjuster shoe bracket on the chain tensioner assembly. figure b shows the stock orientation of the adjuster show and bracket. Figure C shows the adjuster show bracket flipped 180°. To flip the shoe bracket, remove the two ¼-28×2 bolts that hold the bracket assembly together. This will allow you to separate the chain tensioner assembly components from the primary chain. Flip the bracket around as shown in figure c . PAGE 4 Figure B Figure A BAKER COMPENSATING SPROCKET INSTALLATION INSTRUCTIONS 6) install the new compensating sprocket, chain, and clutch onto the motor sprocket shaft and the transmission input shaft. The flipped chain tensioner assembly (as shown in figure c ) is not ‘captured’ on the primary chain like the stock configuration. Loosely install the chain tensioner assembly onto the anchor plate bolt. Tighten the compensating sprocket nut to 157+ 7 ft-lbs and the clutch hub nut to 75+ 5 ft-lbs using red Loctite on the threads.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL SPROCKET KIT INSTALLATION NOTES

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
NORMAL TOOTH WARRANTY This extended warranty applies only to the normal wear that will occur to the tooth profile geometry on the rear belt sprocket. Normal wear is considered wear that occurs when the protective hard coating has worn away exposing the underlying aluminum, changing the profile of the sprocket tooth significantly. Warranty is for five years from date of purchase with unlimited mileage. Warranty claims will require a dated receipt showing proof of purchase from an authorized Harley-Davidson Dealer. Warranty only applies to original purchaser of the sprocket. Original owners name must appear on the receipt. All applications of the sprocket require installation of upper and lower original equipment belt guard, or Harley-Davidson accessory belt guards where applicable. Warranty is voided if these items are not installed. Excessive chips found in the tooth profile due to abnormal riding conditions will void warranty. Occasional chips in the tooth are to be considered normal and should not be considered a warranty issue. Decorative external chrome carries the standard parts and accessories 90 day warranty. Staking the flange on the backside of the sprocket will pierce through the chrome, this is to be considered a normal process and should not be considered an issue. All warranty claims must be pursued through your authorized Harley-Davidson Dealer

HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

Harley-Davidson CHAIN DRIVE INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 15-04-2012

download
1) Assemble & install the chain tensioner assembly over the primary chain as shown in figure 1. 2) Install the compensator sprocket with extender & spacer (numbers 5, 6, & 7, FIG 2)(#7 is not included in this kit), primary chain, chain tensioner, and clutch basket simultaneously onto the motor drive shaft & transmission main shaft. Rotate the chain drive slightly as needed to allow the splines to line-up. 3) Install the chain tensioner nut loosely on the chain tensioner bolt. 4) Install the sliding cam onto the compensator sprocket, & slide the compensating sprocket cover-assembly (#3) over the cam. 5) Apply 2 drops of Rivera “Red” thread-lock on the threads of the motor drive shaft, & install the motor nut loosely with the fingers at this time. The hex spacer (#7) and spacer (#2) as seen in fig.2 are not provided in Rivera Engineering’s chain drive kit. These components are required with some applications, and can be purchased from your local Harley-Davidson dealer. FIG 2 6) Apply 2 drops of Rivera “red” thread-lock on the threads of the transmission main-shaft and loosely install the clutch hub nut (left hand threads). 7) Place the HD “Primary Drive Locking Tool” HD-41214 on the primary chain as shown in figure XXX and tighten the motor sprocket nut to 150-165 foot-pounds. 8)Turn the locking tool 180 degrees and move it to the clutch sprocket. Tighten the clutch hub nut to 70-80 foot pounds (left- hand thread). Adjust chain tension so that the top strand has 5/8″- to-7/8″ of up and down play (cold drive train). Tighten the center bolt nut to 21-29 foot pounds of torque.

Incoming search terms:

HARLEY DAVIDSON REAR THUNDERSTAR WHEELS INSTALLATION, MAINTENANCE AND CLEANING

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Refer to the service manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from a Harley-Davidson dealer. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. See Figure 1. Install valve stem assembly (E) on wheel. Refer to the service manual. 3. Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the appropriate service parts table. Refer to the service manual. NOTES Install the primary bearing first, following the instructions in the service manual and using the WHEEL BEARING REMOVER/INSTALLER. The machined grooves in the hub face indicate the primary bearing side. 4. Install rear wheel (1), stock axle, and stock spacers to motorcycle. Refer to the service manual. MAINTENANCE AND CLEANING NOTE This wheel assembly includes plugs that have been installed in the openings between the brake disc mounting holes on one side of the wheel and in the compensator bowl of the 16×5 inch wheel. Missing or damaged plugs can be replaced using Wheel Plug Kit (44459-04) or individual plug (43871-09 – 16×5 inch wheel). Chrome parts must be maintained regularly so they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

HARLEY DAVIDSON REAR ROAD WINDER WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 1 and Service Parts Tables. INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Refer to the service manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from you dealer. See your dealer for the correct part number for your model motorcycle. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. See Figure 1. Install valve stem assembly (E) on wheel. Refer to the service manual. 3. Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the appropriate service parts table. Refer to the service manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The machined grooves in the hub face indicate the primary bearing side. 4. Install rear wheel (1), stock axle and stock spacers to motorcycle. Refer to the service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

HARLEY DAVIDSON STREAMLINER FOOTPEG KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
NORMAL TOOTH WARRANTY This extended warranty applies only to the normal wear that will occur to the tooth profile geometry on the rear belt sprocket. Normal wear is considered wear that occurs when the protective hard coating has worn away exposing the underlying aluminum, changing the profile of the sprocket tooth significantly. Warranty is for five years from date of purchase with unlimited mileage. Warranty claims will require a dated receipt showing proof of purchase from an authorized Harley-Davidson Dealer. Warranty only applies to original purchaser of the sprocket. Original owners name must appear on the receipt. All applications of the sprocket require installation of upper and lower original equipment belt guard, or Harley-Davidson accessory belt guards where applicable. Warranty is voided if these items are not installed. Excessive chips found in the tooth profile due to abnormal riding conditions will void warranty. Occasional chips in the tooth are to be considered normal and should not be considered a warranty issue. Decorative external chrome carries the standard parts and accessories 90 day warranty. Staking the flange on the backside of the sprocket will pierce through the chrome, this is to be considered a normal process and should not be considered an issue. All warranty claims must be pursued through your authorized Harley-Davidson Dealer

Incoming search terms: