left blinker not working 2004 harley sportster

You search Auto repair manual PDF left blinker not working 2004 harley sportster, if there are search results will appear below. If search results do not exist, please search by others keyword.





HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

Incoming search terms:

HARLEY DAVIDSON BLADE FRONT WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. or FXSTD: Discard tapered spacer. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. 2. See Figure 2. Install valve stem assembly (L) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the machined groove on the hub face is the primary bearing side for all kits except Kits 41681-07 and 40818-08. For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle. • For 2006 and later FXDWG Models: When correctly installed, the tire will be 0.08-0.2 in (2-5 mm) off of center, compared to the fender. • For 2007 and later FX Softail and 2008 and later FXDWG Models: The left side of the wheel is the primary bearing side. • For 2006 and earlier FX Softail and 2007 and earlier FXDWG Models: The right side of the wheel is the primary bearing side. For Kit 40818-08: • Proper installation of this kit requires the separate purchase of two floating brake discs (44343-01 for 2004 – 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel has machined DOT markings to identify it as the primary bearing side. • For 2008 and later Touring: Install bearing shim (43903- 08) under the primary bearing. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. 4. For FLSTC and FLSTN Models: Install wheel kit and right hand wheel spacer provided in installation kit. Refer to FRONT WHEEL in service manual. For FXSTD Models: Install wheel kit, stock wheel spacer and right side wheel spacer provided in installation kit in place of the tapered spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install wheel kit, stock wheel spacers and spacer provided in installation kit between the left side wheel spacer and the left fork. For all other models: Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual. 5. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to verify that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

Harley Davidson Sportster 4 Piston Rear Brake Caliper installation Manual

0

Filed Under (Harley Davidson) by admin on 02-04-2012

download
Installing Rear Caliper – Sportster Models Removing The Stock Brakes SPORTSTER REAR BRAKE SYSTEM 84 & UP MODELS The basic steps are the same to install a PM rear brake caliper kit on any of the late model Harley Davidson “swingarm” style motorcycles; all require the removal of the rear wheel. Using a suitable lift, raise the motorcycle high enough off the ground to allow you to remove the rear wheel assembly. PHOTO 2 W a r n i n g Center the motorcycle on the lift so that it will not fall while you are working on it. Photo 2: Remove the rear brake caliper assembly by unscrewing the 2 caliper mounting bolts that go through the caliper into the caliper mounting bracket. Lift the caliper up and off the mounting bracket and brake rotor, move the caliper back out of your working area. Don’t remove the brake line from the caliper yet; you will do this just before you are ready to hook it up to the new caliper. The brake pads are held into the caliper mounting bracket by 2 spring clips; slide the brake pads out of the mounting bracket and remove the retaining springs. PHOTO 3 Remove Cotter pin and rear axle nut, slide rear axle completely out. Photo 3: Remove nut from Right rear shock and rotate belt guard up. Slide belt off of pulley and roll rear wheel back 6 – 8″. Photo 4: Remove original caliper bracket from swingarm

Harley Davidson 2004-Up Sportster EZ-Steer Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Installation Notes • Remove front fender, wheel, brake caliper, and fork tubes. • Remove all components attached to stock triple clamps, then the triple clamps themselves. • Remove upper and lower bearings including race. • Install new steering stem bearing races into neck. • Install new upper steering stem bearing with seal into neck. • Install Top and Bottom triple clamps into neck and snug steering stem bolt with washer. • Remove fork tube cap from both forks. • Install fork extensions with o-ring into fork tubes and tighten until fully seated. • Install fork tube caps with o-rings and tighten (see torque table). • Slide fork tubes into triple clamps until the top of each tube cap extends 0.42-0.50 in. above top surface of upper triple clamp. • Tighten 3/8-16 x 1.5″ bolts on upper triple clamp (see torque table). • Tighten steering stem bolt (see torque table). • Tighten pinch bolts on lower triple clamp (see torque table). • Install front wheel assembly and front brake caliper. • Install front fender. Item # Part Description Torque Spec (Lb. Ft.) – Fork Tube Cap 22-58 8 Bolt, Steering Stem, SP 30-35 11 3/8 – 16 X 1.5″ Socket Head Cap Screw 30-35 EZ-Steer Maintenance The bearings in your EZ-Steer rake kit are normal wear items, not subject to replacement under Champion’s one year Limited Warranty for the product. Failure to follow your motorcycle manufacturer’s recommendations for periodic OEM triple-tree maintenance will accelerate the wear on these bearings. Checking/adjustment of the steering stem nut torque with the front end lifted, in accordance with your motorcycle manufacturer’s recommendations, is important to reliable bearing service. Windshield Notes Please note that this EZ-Steer kit accommodates all known windshield types with the exception of a minor modification to Quick Release Compact Windshield, example part no. 58063-04. You will need to oblong the lower bolt holes as shown in figure

2004 HARLEY DAVIDSON SPORTSTER XL, XL CUSTOM TANK BRA KIT Installation Instructions

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
1. See Figure 1. Beginning at the front of the tank, position the elastic strap over front edge of fuel tank against frame backbone making sure elastic strap does not pinch off fuel tank vent tube located underneath left side of tank. When properly positioned, strap will run down front of tank and along bottom toward rear of tank. Adjust, if necessary. Pull bra to the rear of tank and fit bra snugly around rear of tank. When performing the following step, route the elastic strap and steel “S’ hook between the main wiring harness and the frame backbone. If the strap is not routed between the main harness and frame backbone, the “S” hook could eventually cut into the main harness wiring causing electrical system failure which could result in death or serious injury. 2. Position the rear elastic strap around the frame backbone making sure the strap and “S” hook, when fastened, pass between the main wiring harness and frame backbone. 3. Smooth out any wrinkles in bra.

2004 Harley Davidson Micro Tach Tachometer Installation Instructions

0

Filed Under (Harley Davidson) by admin on 26-03-2012

download
Tachometer Installation Instructions for 2004+ Harley Davidson Sportster Custom Look for other model instructions online at www.speedwayinstruments.com Introduction: Installation of the Speedway Instruments microTach+ TM tachometer Tachometer requires some basic mechanical skills, including removing decorative covers, cutting protective tubing around wires, and using suitcase splice connectors to splice existing wiring harness. These actions may void your warranty, and if done incorrectly may cause damage to your motorcycle. Only you know your capabilities, if you do not feel capable of making modification please have a qualified motorcycle technician install it. Speedway Instruments, LLC is not responsible for damage to your motorcycle due to improper installation. These instructions utilize a 2004 Harley Davidson XL1200C motorcycle as basis for the all descriptions and pictures. Variations in location, color and procedure may be required for different year and make. Please refer to the Service manual to confirm the proper color and location of wires. Please make sure you have the proper service manual and tools before starting the installation. 1. Turn ignition off and disconnect Battery. 2. Determine a mounting position. Each motorcycle is unique and the microTach+TM tachometer is small enough to be placed in many different locations to provide an attractive appearance and vital engine status. Possible locations are: a. Front Brake Reservior b. Top handle bar clamp

HARLEY DAVIDSON HARDWARE/ TURN SIGNAL RELOCATION KIT FOR SPORTSTER LEATHER SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
Installation Instructions for 79052-04 and 79073-04 Do not exceed 7 lbs (3.17 kg) maximum load in each saddlebag. Additional weight can affect a motorcycle’s stability, handling characteristics, and safe operating speed which may lead to an accident resulting in death or serious injury. NOTE A pick tool (Snap-on TT600-3) will be required for 1996 and later models for removing and reinstalling a multi-lock amp con- nector. NOTE A Service Manual for your vehicle is available from your Harley- Davidson Dealer. Installation – Hugger Models Only (1994-1997) To perform the following steps for Hugger Models only, fender and frame must be sufficiently supported, as both shocks will need to be removed at the same time. An improperly supported vehicle could result in death or serious injury. A Service Manual is needed to install this kit. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson Dealer perform the installation. Improper installation of this kit could result in death or serious injury. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove seat, sissy bar and sideplate, if applicable. Retain hardware for reinstallation. Disconnect battery, negative cable first. 2. Properly support motorcycle under frame to prepare for removal of right and left shocks. 3. Remove rear buttonhead screw on each side of fender. 4. See Figure 1. With rear fender and frame securely supported, remove left and right shocks by removing upper nut (2), washer(s) (3) and shock cover (4). Remove bolt (6), washer (7) and locknut (8) at lower shock mount. Remove shock

2001 – 2004 Camry, Highlander, Solara & 2004

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
2004 model year Camry, Highlander, Solara and 2004 model year RAV4 vehicles with the 2AZ-FE engine may exhibit squealing and/or rattling noises coming from the engine compartment during vehicle operation especially after a cold soak. The belt tensioner assembly has been improved to correct this condition. 2001 – 2004 model year Camry, Highlander and Solara vehicles equipped with 2AZ-FE engines produced BEFORE the Production Change Effective VINs shown below. 2004 model year RAV4 vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE LINE PRODUCTION CHANGE EFFECTIVE VIN TMMK Line 1 4T1BE3#K#4U358206 Camry TMMK Line 2 4T1BE3#K#4U914052 y 2AZFE Tsutsumi JTDBE3#K#40296732 Highlander 2AZ-FE TMK JTE#D2#A#40100501 Solara TMMK 4T1CE3#P#4U914074 RAV4 Tahara JTE#D2#V#40029797 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 16620-28010 16620-28011 Tensioner Assembly, V-ribbed Belt 1 OP CODE DESCRIPTION TIME OFP T1 T2 EG8001 R & R Accessory Belt Tensioner 0.9 16620-28010 91 55 Applicable Warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

HARLEY DAVIDSON SADDLEBAG GUARD RAIL KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation NOTE A Service Manual for your vehicle is available from your Harley-Davidson Dealer. 1. Remove saddlebags from motorcycle according to Service Manual instructions. 2. Remove left and right side covers (located just ahead of saddlebags) by removing Phillips head screw from bottom of side cover. Save hardware and side covers for later reassembly. 3. Remove upper and lower bolts securing left and right forward saddlebag guards to frame. Remove Phillips head screws securing saddlebag guards to muffler supports. Discard saddlebag guards, but save hardware. 4. See Figure 1. Install new left and right forward saddlebag guards (1) with upper bolts (2), lower bolts (3) and Phillips head screw (4) saved from Step 3. 5. Insert one rear guard rail mount (6) onto rounded, tubular end of one of the saddlebag side guard rails (5). 6. Insert a hex cap screw (8) through one of the front guard rail mounts (7) as shown. 7. Line up saddlebag side guard rail (5) with attached rear guard rail mount (6) from Step 5 with lower hole in forward saddlebag guard rail (1). Insert hex cap screw (8) from front guard rail mount (7) through hole in forward guard rail (1) and into side guard rail assembly. Tighten finger tight. 8. See Figure 2. Install a side guard rail (2) in lower position on rear fender support (3) with pan head screw (1). Tighten finger tight. 9. Repeat Steps 5 through 8 in upper position. 10. Repeat Steps 5 through 9 for opposite side of vehicle. NOTE Each of the four guard rail clamps vary slightly. Two fit together for the right side of the motorcycle and two fit together for the left side. The inner right and left clamps have two holes drilled through them. 11. See Figure 2. Locate four guard rail clamps (4). Match up two left side and two right side guard rail clamps. Install one piece of cushion tape to the lower inner surface of right and left inner clamps. Peel off paper from outer surface of tape. Do not apply tape to the outside clamps. NOTE Be sure that you correctly position the inner clamps on the side guard rails, as directed in Step 12, before tape on inner clamp contacts side guard rails. Tape is very sticky and will be difficult or impossible to remove once it has made contact with side guard rail surface. 12. See Figure 2. Position clamps (4) in desired position on side guard rails (2). Install clamps (4) on left and right side of vehicle side guard rails using four Torx screws (5). Torx screw heads should face inward toward motorcycle. Tighten each screw a little at a time until secure. 13. Tighten hex cap screws and pan head screws installed in Steps 7 and 8.

Incoming search terms:

HARLEY DAVIDSON SPORTSTER LOW REAR SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION NOTE Internal shock absorber components are not repairable beyond the Service Parts listed on this instruction sheet. Consult your Harley-Davidson dealer if further service is required. The installation procedures for this kit are the same as the original equipment (OE) installation procedures in the Service Manual. Refer to the appropriate Service Manual for the rear suspension system removal and installation procedures. The OE hardware will be re-used in the kit installation. Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) SHOCK PRELOAD (SPRING) ADJUSTMENT Refer to the appropriate Service Manual for spring adjustment. Spanner wrench (94700-52L) is required for spring adjustment. SERVICE PARTS 1 is04854 Figure 1. Service Parts: Sportster Low Rear Suspension Kit Table 1. Service Parts: Sportster Low Rear Suspension Kit Part Number Description (Quantity) Item 54734-04 Rear shock (2)

Incoming search terms: