lift truck cup holders

You search Auto repair manual PDF lift truck cup holders, if there are search results will appear below. If search results do not exist, please search by others keyword.



  lift truck cup holders Direct Download speed 5282 Kb/s

  lift truck cup holders Full Version speed 6162 Kb/s



AJS DISMANTLING AND REBUILDING FULL-WIDTH FRONT WHEEL HUBS INSTALLATION

0

Filed Under (AJS) by admin on 31-10-2010

download
Removal of the Brake-side Bearing Cup The bearing cup (5) is located endwise by a circlip (1), and between the cup and circlip arc an oil-seal retaining washer (4), oil seal (3), and oil-seal cup washer (2) Before these parts can be removed from the hub the bearing cup must be moved inwards for a very short distance (3/16-inch) so that the circlip can be withdrawn. (n) Gently heat the hub shell. (i) Place a soft metal rod (e.g. brass) against the oil-seal cup washer (2) and apply pressure with a hand press or hammer blows. It is only necessary to move the bearing cup (5) inwards about 1/16-inch. (j) Extract the circlip by inserting a narrow pen-knife blade under one end of the circlip; lift it upwards and outwards and prise the clip out of its groove. (k) Remove the oil-seal cup washer (2), oil seal (3) and oil-seal retaining washer (4). They can be hooked out with the shank of a small and narrow screw­ driver, (l) The bearing cup can now be ejected by placing a suitable rod of soft metal (e.g. brass) in the hub tunnel from the right-hand side and pressing it — with a press or hammer blows — against the bearing cup until the cup is forced out of the bearing. This must be done with care so that the cup remains square with the housing. Reassembly To facilitate replacement of the bearing cups gently heat the hub shell. Just too hot to hold is about the right temperature. (a) Place the brake-side bearing cup squarely in the hub shell — the open end faces inwards — and press it into the hub tunnel A short length of brass rod, slightly less than the outside dia­ meter of the cup, should be interposed between the cup and ram of the press, or hammer head. Press the cup in until the outer face is approximately half-an-inch below the mouth of the hub tunnel. This will allow sufficient room to allow [he circlip to be inserted into its groove. (b) Refit in the following order: oil-seal retaining washer (4), oil seal (3), oil-seal cup washer (2). (c) The circlip can now be replaced. In the interest of reliability use a new circlip, for it is possible that the existing circlip was strained when it was re­ moved. (d) Insert into the hub tunnel from the right-hand side a brass rod of suitable length, and press the bearing cup firmly against the circlip. (e) Before inserting the spindle complete with the roller races, pack them with clean and fresh grease of a suitable grade (Mobilgrease No. 4. Castrolease heavy, Energrease C3, Esso Pressure Gun Grease. Shelf Retinax Grease CD or A). (0 Insert the spindle into the hub. (g) Place the right-hand side bearing cup in the hub tunnel; the open end faces inwards, It may be necessary to re-heat the hub to allow the cup to go into position without difficulty. (h) Press the cup into position, but do not force it fully home, leave some end play on the spindle. (i) Refit in the following order: oil-seal retaining washer (6), oil-seal (7) and oil-seal cup washer (8). (j) Screw into the hub the adjusting sleeve (9) until it comes into contact with the bearing cup (5)

Incoming search terms:

PRO-CYCLE AND PRO-CYCLE XLT 1,000-Lbs. Capacity Motorcycle Lift

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
1. Always inspect the lift for freight damage and make note of any damage on the bill of lading. 2. In case of freight damage, call the truck line immediately and report the damage as a freight claim. Final Set-Up for model Pro-Cycle This lift is more than 90% factory pre-assembled. The following steps will guide you through the final set-up. IT WOULD BE EASIER FOR TWO MEN TO COMPLETE FOLLOWING STEPS. 1. Unpack the lift from the shipping skid. With the lift table up side down, connect the air hose to the air cylinder (Part # 26). 2. After tightening the hose to the cylinder, flip the lift over with the table surface up. 5 3. Lift up the table manually to the first lock position to make sure the lift is rising freely. Lubricateing the joints again before use will ensure a better performance of the lift. 4. Connect the other end of the air hose to the foot-operated valve. Then connect the foot- operated valve to 100 PSI air supply. DO NOT USE AIR SUPPLY WITH PRESSURE MORE THAN 100 PSI. 5. Release the safety bar by pushing the handle down. Operate the foot valve by stepping on the footpad forward to raise the lift. The safety bar should engage the ladder automatically while lift is rising. Step on the footpad again to set the pad in middle position to stop the lift when it reaches the desired height. ALWAYS LOWER LIFT IN THE NEAREST LOCKED POSITION BEFORE BEGINNING WORK. NEVER USE THE LIFT UNLESS YOU ARE IN A LOCKED POSITION. The lift should never be left unattended while attached to air pressure. Disconnect the air pressure when lift is not attended by qualified persons. 6. Install the vise using bolts and nuts supplied with the lift (part # 6 to 12). See fig #1. 7. Install the approach ramp by dropping it into the holes punched on the rear edge of the table. The final Set-Up for the Pro-Cycle model is complete

Incoming search terms:

1500 XLT MOTORCYCLE / ATV LIFT INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
1. Load should not exceed rated capacity for this lift – 1500lbs 2. 70-160PSI shop air needed. 3. Make sure the handle is in the down position and the safety plate is set in the safety lock while the lift is in the raised position. 4. Move the lift only when it is lowered. 5. Do not ride vehicle onto lift. 6. Only trained people should operate the lift. 7. Air/Hydraulic pump should be at least 3 feet away when operating. Remain clear of the lift when raising or lowering. 8. Indoor use recommended. 9. Do not move lift while loaded. 10. Keep hands, tools and other extremities from under carriage and moving parts.. 11. Maintain a safe working environment. The work area should be clean, dry, clutter free, and sufficiently lit. 12. Wear proper ANSI-approved safety attire. Do not wear loose fitting clothing while operating lift, long hair and sleeves should be secured. 13. Keep children and bystanders away from work area. Do not let children operate or play on lift. 14. Do not use if under the influence of drugs or alcohol. Operator must be alert at all times when using heavy lift equipment. 15. Never operate the lift with someone on it. 16. Do not adjust safety valve. 17. Use this lift only for the work it is intended. Do not use this product for an application for which it was not designed. Misuse can lead to personal injury and/or property damage. 18. Industrial applications must follow OSHA requirements. 19. Do not use for aircraft purposes. 20. Have your lift serviced by a qualified repair person using only identical Titan Lifts® replacement parts and attachments. This will ensure that the safety of the lift is maintained.

AIR / HYDRAULIC MOTORCYCLE LIFT REMOVABLE INSPECTION PLATE

0

Filed Under (Tips and Review) by admin on 19-11-2010

download
For best service, you should incorporate an oiler, regulator, and inline filter, as shown in the diagram on the next page. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. NOTE: If an automatic oiler is not used, put 3-5 drops of pneumatic Tool Oil (not included) in the Motorcycle Lift’s Quick Coupler (38A) before each use. (See Figure B, next page.) To Check The Level Of Hydraulic Oil: 1. The Motorcycle Lift already contains some hydraulic oil in its Hydraulic Pump Reservoir (32P). Even so, it is recommended that you check the oil level in the Reservoir and, if necessary, top off the Reservoir with the proper amount of 15/40 hydraulic oil (not included). (See Assy. Diagram, page 15.) 2. Make sure to screw the two Adjusting Screws clockwise enough to lift the two Caster Wheels (14) off the floor so as to provide stability for the Motorcycle Lift. (See Figure A.) 3. To check the level of hydraulic oil, remove the Sliding Plate (36) from the Platform (35) to expose the Hydraulic Pump Reservoir (32P). (See Assy. Diagrams, pages 13 and 15.) 4. Remove the rubber Filler Plug (33P) located on the top of the Reservoir (32P). If necessary, top off the Reservoir with hydraulic oil. (See Assy. Diagram, page 15.) 5. Connect the air compressor’s hose to the to the Air Motor assembly. Then turn on the air compressor and set its regulator at 120 PSI. (See Assy. Diagram, page 14.) 5. Insert the Lift Foot Pedal (11) onto the Pump Piston Spindle (9), and slowly pump the Lift Foot Pedal until a slight amount of hydraulic oil begins to leak out of the Reservoir (32P). Discontinue pumping the Lift Foot Pedal. Then, replace the Filler Plug (33P) on the top of the Reservoir. (See Assy. Diagram, page 15.) REGULATOR OILER FILTER TO QUICK COUPLER (38A) OF MOTORCYCLE LIFT FIGURE B 6. Insert the Release Foot Pedal (10) onto the Release Valve Spindle (5). Pump the Lift Foot Pedal (11) until the Platform (35) of the Motorcycle Lift reaches its maximum height. Then press down slightly on the Release Foot Pedal until the Platform is fully collapsed to the floor. Repeat this procedure several times to ensure the Motorcycle Lift is operating properly. (See Figure E, page 10.)

Incoming search terms:

COMMANDER 1,000 LBS. CAPACITY MOTORCYCLE LIFT INSTALLATION AND OPERATION MANUAL

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
Your lift comes packaged as a single unit. A fork-lift, floor-jack or other heavy-lifting equipment may be necessary to separate the components. Exercise caution when disassembling the packaged lift, as shifting may have occurred during shipping. 2] Carefully unpack the lift. Check for any obvious shipping damage. (Remember to report any shipping damage to the carrier and make a notation on the delivery receipt.) 3] Carefully turn the table upright into operating position before removing shipping cable restraint from scissor mechanism. 4] Connect foot-operated air valve to 100 psi maximum air supply. The lift may be damaged and/or personal injury may result if the pressure exceeds the maximum 100 psi rating. 5] Stand clear of lift table, and depress the “UP” side of the foot valve to raise the table. 6] To lower table, lift locking bar from safety latch and lower to next position, or to the floor. 7] Place drop-out cover over drop out opening. 8] Insert ramp mounting pins into holes at either end of table to mount ramp. NOTE: If cycle vise is being installed, ramp must be mounted opposite the cycle vise. OPERATION and MAINTENANCE 1] Loads must be centered on table at all times. Table is rated for a maximum load of 1,000lbs. 2] Loads must be firmly positioned and secured on table at all times. 3] All moving parts have been lubricated at the factory and should be re-lubricated every six (6) months to prevent problems. Grease points are located at each end of frame pivot shaft and at top ends of inside frame assembly. 4] Lightly oil cylinder rod when it becomes dry. 5] Squirt some oil through bleed hole in plate end of cylinder to lubricate piston and its seal every six (6) months. 6] Pivot shaft set screws should be checked frequently to be sure they are tight. These are located at the top end of the inside frame assembly.

1,000 POUND CAPACITY MOTORCYCLE / ATV LIFT RML-600 INSTALLATION AND OPERATION MANUAL

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
6 RML-600 Instructions 1. Center load on table – 1000 lb. maximum. 2. Connect to 100 PSI maximum shop air. 3. Keep safety bar in position at all times – except when lowering. 4. Keep hands and tools from under carriage. 5. Do not mount table when in elevated position. 6. Do not ride vehicle onto lift. 7. Lift must be in the lowered position when moving. 8. Only trained persons should operate Air Lift. 9. The working area should be sufficiently lit. 10. Foot controller should be at least 3 feet away from Air Lift during raising and lowering operation. 11. Lift is recommended for indoor use only. nstallation Instructions The Cycle Vise mounts directly onto the RML-600. Align two inside holes of the fixed clamp over the existing vise hole pattern as shown. Align the moveable clamp with the locating corner hole. CYCLE VISE
8 1. Insert pipes from extension panel package through holes in lift table. 2. Mount panels on ends of pipe on each side of table. With ramp hole to outside. 3. Insert M8 BOLTprovided through holes in each end of pipe. 4. Secure ramp extensions to ramp with bolts provided. Make sure ramp hooks are positioned on the outside. 5. Stabilization bar directions – Unscrew cap from one of the ends of the stabilization pipe. 6. Insert bolt in drilled out hole and tighten with nut. Slide pipe through the stationary square tubing on the lift legs. Insert the other bolt, tighten down with nut. Put on the other cap and tighten. Installation Instructions (Optional) 12″ Side Extensions
9 POSITION THE 13″ EXTENSION OVER THE EXISTING TABLE AS SHOWN AND ATTACH WITH FOUR M8 CAPSCREWS, NUTS AND LOCK WASHERS PROVIDED. EYE BOLTS ARE ALSO PROVIDED WITH THE EXTENSION KITAND MAYBE INSTALLED AS SHOWN USING M8 HEX NUTS AND LOCKWASHERS

2003 – 2004 4Runner REAR SEAT CENTER ARMREST CUP HOLDER REPAIR

0

Filed Under (Toyota Manuals) by admin on 28-10-2011

download
The ends of the zipper are concealed in the cover. Pull out both ends of the zipper from the cover. B. To unlock the zipper, flip the zipper’s tab so that it points away from the direction the zipper will be opened. C. Open the zipper by pushing the tip of the tab. 3. Roll Up Cover. A. After opening the zipper, roll up the cover. B. Roll up the cover until the foam pad’s 3 holes are revealed. 4. Remove Cup Holder. A. Remove the screws from each of the 3 holes. B. Pull the cup holder out of the armrest. If the cup holder is difficult to remove, hold the armrest with the cup holder facing down and shake the armrest for cup holder remova

MOTORCYCLE SERVICE LIFT ADAPTER KIT FOR DYNA TC88 MODELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 28-04-2011

download
Installation A Service Manual for your motorcycle is available at your Harley-Davidson Dealer. 1. See Figure 1. Position the motorcycle on a straight and level surface. While the bike rests on the Jiffy Stand, straighten the front wheel and place the frame leveling extrusion under the front tire to keep the tire straight. 2. Slide the motorcycle lift (fully lowered) under the bike from the right side (opposite jiffy stand side) lining up the frame rails with each of the perpendicular jacking rails on the lift. When properly aligned, the left frame rail will be approximately 1″ from the lift end section (Figure 2) and lift base will be adjacent to the Jiffy Stand (Figure 3). This will allow bike to be centered when moved to an upright position

Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

Honda 300 2×4 Lift Kit Installation Instructions

0

Filed Under (Honda) by admin on 11-12-2011

download
This product is designed for us e on ATVs on which additional ground clearance and fender clearance is desired. It is designed for utility type, slower-speed use on relatively flat terrain in deep mud or snow. Although we have many thousands of satisfied lift kit customers and over 400 franchised dealers selling and installing lift kits, purchasers should be aware that use of this product may increase the frequency of required maintenance, part wear, and will raise the center of gravity on your ATV increasing risk of roll-over on side hills, ditches or other steep terrain. We recommend that wider tires and/or wheel spacers be used to achieve a wider stance and to improve stability of the ATV. Riders should be advised that the handling characteristics of a taller ATV are different and require extra care when riding on side hills or off-camber situations. If you further raise the center of gravity by adding heavy loads to racks or seats, the ATV must be operated with care, at slower speeds or on relatively flat ground. Operation of an ATV with or without a lift kit, while or shortly after consuming alcohol or drugs, subjects the rider to the risk of serious bodily harm or possible death. This is compounded if the rider does not wear an approved helmet and other safety gear. High Lifter urges that all approved safety gear be worn when riding an ATV. If this is not what you expected, or is not consistent with your intended use, you should return the product immediately to the seller, before installation, for a refund of the purchase price; less any fees. After installation, product is warranted for 90 days for defects in workmanship and materials. Warranty is limited to refund of the purchase price or replacement of the kit, at the seller’s option.

Incoming search terms: