lube for gl1800 drivesaft

You search Auto repair manual PDF lube for gl1800 drivesaft, if there are search results will appear below. If search results do not exist, please search by others keyword.





2001 – 2002 GL1800/ GL1800A Rear Tire Inspection

0

Filed Under (Honda) by admin on 27-11-2010

download
1. Inspect the motorcycle for a punch mark as described in Identification on page 2. If a punch mark is present no further action is necessary, return the unit to the customer. 2. Qualify the unit/customer as follows: •Is the tire on the motorcycle the original factory installed tire? •Is the air pressure loss more than three psi per month? Note: Refer to page 145 in the Owner’s Manual. “Even tires that are in good condition may lose one to two psi per month if not checked and adjusted regularly” . If the GL1800 meets the above qualifications, proceed with the repair procedure. 3. Place the motorcycle on a lift and secure it on the centerstand. 4. Remove the rear wheel as described on page 14-9 of the Service Manual. 5. Starting at the valve stem/balance mark area, carefully remove the rear tire from the wheel. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. 6. Carefully inspect the entire circumference of both tire beads. Inspect both the inside and outside of the bead for any distortion or injuries. See examples of injuries below. 2001 – 2002 GL1800/GL1800A Rear Tire Inspection GL1800 #6 OCTOBER 2001 MTB 9430 (0109) CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your Honda. These procedures should not be attempted by “do-ityourselfers,” and you should not assume this bulletin applies to your Honda, or that your Honda has the condition described. To determine whether this information applies, contact an authorized Honda dealer. Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800/GL1800A Rear Tire Inspection 0110 GL1800 #6*GL1800 #6*0110*2001-2002 GL1800/GL1800A Rear Tire Inspection*GL1800/GL1800A, Rear Tire Inspection, Bead, Tread*Motorcycle*1800 2 of 4 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #6 OCTOBER 2001 Inside BeadInjury Outside BeadInjury Outside BeadInjury 7. Carefully inspect the entire circumference of both tire beads. Inspect both the inside and outside of the bead for any distortion or injuries. See examples of injuries below. 8. If there is no evidence of bead damage, re-install the tire on the rim. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. Be sure to align the balance dot with the valve stem. Inflate the tire to 41 psi. Install the wheel assembly on the motorcycle and proceed to the Identification and then to the Warranty section. 9. If any damage or injury is present replace the tire and valve stem. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. Balance the new tire as necessary

Incoming search terms:

2001-2002 GL1800 A ABS Speed Sensor Wire Clamp Location INSPECTION/ REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
1. If the VIN is within the preceeding range, inspect the front ABS speed sensor wire clamp according to the following illustrations. 2001-2002 GL1800A ABS Speed Sensor Wire Clamp Location INCORRECT Installation CORRECT Installation Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location 0112 GL1800 #9*GL1800 #9*0112*2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location*GL1800, ABS Speed Sensor Wire Clamp Location*Motorcycle*1800 2 of 2 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #9 DECEMBER 2001 IDENTIFICATION There is no identification mark associated with this Service Bulletin. PARTS INFORMATION There is no parts information associated with this Service Bulletin. WARRANTY INFORMATION The normal warranty claim submission requirements apply. Submit one warranty claim per VIN with the following information only: Inspected and REPAIRED Template: GL#9 Hours: 0.2 hours Parts: None If the clamp is installed correctly on top of the speed sensor, no further action is necessary. 3. If the clamp is installed incorrectly under the speed sensor, remove and reinstall the clamp and speed sensor correctly. Torque the bolts,. Torque: 12 N • m (1.2 kgf • m, 9 lbf • ft) If the speed sensor wire clamp for the front ABS speed sensor is installed incorrectly, the ABS speed sensor air gap may be out of specification. This does not affect ABS speed sensor operation, but the clamp should be installed correctly. Inspect and repair all affected units using the Inspection/Repair procedures listed below. Inspect all unsold units and customer units brought in for service. AFFECTED UNITS 2001-2002 GL1800A units as follows: MODEL 2001 GL1800A All units 2002 GL1800A 1HFSC474*2A100001 – 1HFSC474*2A101643 * = denotes check digit Any unit in the above VIN range may be affected and should be inspected according to the procedures in this Service Bulletin. All units outside of the above VIN range do not require inspection. CUSTOMER NOTIFICATION There is no customer notification associated with this Service Bulletin.

Incoming search terms:

2001-2002 Honda GL1800/A Frame Weld Inspection PROCEDURE

0

Filed Under (Honda) by admin on 22-04-2011

download
IMPORTANT: During these procedures you may be using and referring to the following materials, originally sent to you with Service Bulletin GL1800 #14. • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Procedures (S0510) • Frame Weld Inspection Chart (S0516) • 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511) • 2002-2003 GL1800/A Frame Weld Safety Recall Cracked Weld Repair Manual (S0515) • Welding Template Box (S0512)If you need additional copies of these materi- als you may order them at no cost from Resolve at (440) 572-0725. 1. Position the motorcycle on a firm, level surface, in an area where there is enough room to safely lay it on its left side. 2. Remove the left side mirror by following the nstructions on page 2-7 of the Service Manual. 3. Remove the left engine side cover by following the nstructions on page 2-5 of the Service Manual. 4. Remove the antenna whip(s). 5. Remove the coolant reserve tank by fol- lowing the instructions on page 6-7 of the Service Manual. 6. Place thick, non-abrasive padding (such as furniture blankets) on the ground to protect the motorcycle when you lay it on its side. 7. Lock the handlebars to the RIGHT, using the ignition key. 8. Using two people, gently lay the motor- cycle down on its LEFT side on the pad- ding. The motorcycle will first rest on the wheels and left engine and saddlebag guards. Continue to lean the motorcycle to the left until it rests on the left handlebar end and left engine and saddlebag guards. The motorcycle should be laying on the padding, with its engine guard, saddlebag guard, and handlebar end resting on the padding – no painted parts should be con- tacting the padding. 9. Clean the frame crossmember with acetone. 10. Draw a line on each side of the grinding template (S0512) 30 mm from the for- ward edge, stopping  between the two arrows, as illustrated below. 11. Put this template on the frame and, using a fine-tipped felt marker (such as a Sharpie), draw a 30 mm line on both crossmember welds. Start this line at the forward edge of the grinding template and stop between the two arrows as shown in the illustration on the next page.Now remove the grinding template

2001-2004 HONDA GL1800/A Trunk Opener Unit Removal/ Installation instructions

0

Filed Under (Honda) by admin on 29-01-2011

download
come customers may experience trunk or saddlebag lids not opening when the corresponding latch lever is pulled. To correct this condition, the opener mechanism must be replaced with a new opener mechanism. Follow the Trunk Opener Unit Removal/Installation instructions in the GL1800/A Gold Wing Service Manual. Opener Unit P/N: 81310-MCA-A22 H/C: 7700768 The normal GL1800/A warranty applies. Follow all normal warranty procedures and guidelines. Labor Operation: 412122 Flat Rate Time: 0.6 If you feel that goodwill consideration is appropriate, contact your District Service Manager or TechLine BEFORE starting this repair. 2001-2004 GL1800/A Trunk Opener Unit MTB 10535 (0403) GL1800/A #15 MAY 2004 REPAIR PROCEDURE PARTS INFORMATION WARRANTY INFORMATION QUESTIONS PART DESCRIPTION TRUNK OPENER UNIT

Incoming search terms:

BMW Airhead Motorcycle Spline Lube Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
An Airhead spline lube is a necessary maintenance task, covered extensively in some of the other online articles listed below. It’s actually a fairly easy job, and there are several good articles (see below) that cover all the details. I’m not sure if I’m adding anything to the general knowledge with this article, but I took some photos when I performed a spline lube on my 1986 R65 and 1984 R100RS, and I hope these somewhat poor quality photos can help. By the way, the 1986 R65 motorcycle is a later model “monoshock” with a “single-sided” swingarm, so the procedure may be slightly different than other Airheads, although I have since used the same procedure on my 1984 BMW R100RS and not much is different. In fact, I’d venture to say that the spline lube on the dual-shock R100RS is actually a bit easier; either that, or my experience with spline lubes is paying off!. The job took me about 3-4 hours the first time and less than 2 hours the second time. First thing I did was to pry off the two plastic covers over the swingarm nuts (pink arrow, photo left). I wanted to make sure that the 27mm socket I owned would fit in between the nut and the frame before I started the job, otherwise it would mean a trip over to Sears to see if I could find the correct socket. Fortunately, the 1/2″ drive 27mm socket I have worked fine without any modifications on both the ’86 and ’84, although it just barely fit the ’84. Apparently, some BMW’s were not machined concentrically in this area, and the 27mm socket may have to be machined or ground to fit. Bob Fleischer goes into this in detail in his article listed above. By the way, a 1-1/16″ socket will also work, because 27mm is almost exactly 1.062. Some sockets may have too large a radius at their open edge, which may prevent enough of the socket’s “teeth” from grabbing the very thin swingarm nut. You may have to grind or machine off the end of your socket to fit. Craftsman sockets have a (bad) reputation for having too large a radius, which helps them slip easier over a nut, but can also make them slip off just as easy in tight spots such as this. Although most of my tools are Craftsman, and I’ve never really found this to be a problem.

Incoming search terms:

Honda Goldwing GL1800 Solid Rear Axle Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Specifications Overall Width: 57.75″ Overall Length: 108″ Overall Length w/EZ-Steer 109.5 Wheel Base: 71″ Extended 4.5″ At Rear Axel Wheel Base w/EZ Steer 72.5″ Load Capacity: 500 Lb Tire Size: 205 / 70 / R15 Wheel Size (15″) Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20 PSI Suspension: “Zero-Flex” Internal Swing Arm utilizing 3 shocks, OEM shock absorber plus 2 coil over shock absorbers. Rear Differential: Champion Lightweight rear axle / differential assembly. Gear Ratio 2.93:1 gear ratio Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 6.75 cubic feet. 3 full-face helmets and additional storage. Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 7 of 28 Revision 10 4 Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. • Seat (to be re-installed without modification) • Left and right side covers (to be re-installed without modification) • Battery and battery box (to be re-installed without modification) • Left and right saddle bags • Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) • Trunk (to be re-installed without modification) • Left and right passenger foot rests (to be re-installed without modification) • Left and right foot rest under covers (to be modified and re-installed) • Left and right rear crash bars • Saddle bag trunk stay (to be modified and re-installed) • Left and right mufflers (Mufflers only, do not remove decorative covers) • Rear wheel • Left and right pivot bolt covers (to be re-installed without modification) • Reverse resistor (to be relocated) • Swing Arm – Note : Carry out brake system modifications (Section 5) prior to removing Swing Arm. • Note : Upper bolt of mono shock can be removed without removing the fuel tank. • Note : Do not remove actuator hose from actuator pump or shock absorber. Dismounting shock actuator pump will allow more movement of shock absorber when removing swing arm.Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 8 of 28 Revision 10 5 Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm. From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Sidecars Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Sidecars Trike Conversion Kit.

Incoming search terms:

2002-2003 Honda GL1800/ A Frame Weld REPAIR PROCEDURE OVERVIEW

0

Filed Under (Honda) by admin on 14-12-2010

download
If your inspection identifies a crack or cracks in or on either Left or Right lower crossmember frame welds, STOP – call your DSM or TechLine for further instructions. • If your inspection reveals no cracks, proceed to REPAIR PROCEDURE. NOTE: Verification of repair can also be found in the Dealer Responsibility Report and on the Honda Interactive Network (iN). If you have any questions about verification, please contact TechLine before proceeding. IMPORTANT: For complete Dealer and Welder Repair procedures, refer to the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Booklet (S0510) • Frame Weld Inspection Chart (S0513) You MUST provide your TIG welder with the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511) • Welding Template Box (S0512) All of the above items were shipped to you with this Service Bulletin. If you need additional copies of the Dealer Booklet , Welding Manual , Welding Template Box , or Frame Weld Inspection Chart , you may order them at no cost from DDS at (440) 572-0725. For your reference, a brief repair procedure overview is provided below. Disassembly Overview You will be removing the following components from the vehicle as instructed in the Dealer Booklet : • Handlebar weights • Rear view mirrors • Swingarm pivot covers • Rider foot pegs • Seat • Side covers/Engine side covers • Fairing pockets • Fairing molding • Meter panel • Top shelter • Battery • Fuel tank • Main wiring harness ground • Front lower fairing • Front exhaust pipe protector • Muffler/exhaust pipe • Antenna Whip(s) • Coolant reserve tank • Center stand NOTE: You will need to remove any accessories that may contact the ground during the Welding and Re-assembly procedures. IMPORTANT: You MUST cover the following with RED duct tape for welder identification pur- poses: • Negative (-) and positive (+) battery cables • Fuel return hose end • Fuel feed hose end • Main wiring harness ground • Alternator • Exhaust ports Welding Overview A qualified TIG welder will weld the frame following the procedures in the 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual . Re-assembly Overview You will be inspecting the new TIG welds, painting the frame, and re-assembling the vehicle as detailed in the Dealer Booklet and Frame Weld Inspection Chart (S0513)

Incoming search terms:

2001-2002 GL1800/ A CB Radio Replacement/ REPAIR PROCEDURE

0

Filed Under (Honda) by admin on 29-01-2011

download
For authorization, call the CB Exchange Radio Order Desk toll free: (888) 997-7278 . The CB Exchange Radio Order Desk hours are Monday thru Friday, 8:30am – 8:00pm EST. BEFORE STARTING ANY REPAIR ON THE CB RADIO, YOU MUST FIRST CALL THE ORDER DESK FOR AUTHORIZATION. Part Number: 08E95-MCA-101RM Honda Code: 7066319 3. After calling the CB Radio Order Desk, an exchange transceiver will be shipped overnight (freight prepaid). 4. Replace the faulty CB Transceiver with the exchange unit (see REPAIR PROCEDURE ). . Remove the seat (see the GL1800 Service Manual, page 2-4). 2. Remove the right rear side cover (page 2-4). 3. Remove the right-hand fairing molding (page 2-8). 4. Remove the right hand top shelter setting bolts and mounting nut (page 2-9). It is not necessary to remove the left-hand fairing molding, shelter bolts, or shelter. 5. Disconnect the 14P CD coupler under the rear seat. Remove and set aside the CD Changer (if equipped). (Continued on page 2) Some customers may experience weak radio transmissions and/or the need to use abnormally high squelch settings for reception on the Hondaline CB Radio. To correct this condition, the CB Transceiver unit must be replaced as described in this Service Bulletin. Do not order a CB kit from parts stock. Follow the ordering procedures in this Service Bulletin. AFFECTED MOTORCYCLES 2001 – 2002 GL1800/A ORDERING AND REPLACING THE CB TRANSCEIVER 1. Before calling the CB Exchange Radio Order Desk, have the following information ready: • VIN • Failure Information (i.e., symptom) • Warranty Status 2. For authorization, call the CB Exchange Radio Order Desk toll free: (888) 997-7278 . The CB

Incoming search terms:

HONDA 2002-2004 GL1800/A Linked Braking System (LBS) Proportional Control Valve (PCV) Leakage

0

Filed Under (Honda) by admin on 25-11-2010

download
1. Pump the rear brake pedal four times. •If the brake pedal feels spongy, bleed the brake system per the Service Manual. After verifying proper brake system operation, proceed to step 2 below. •If the brake pedal does not feel spongy, proceed to step 2 below. 2. Place the motorcycle on its side stand, with the handlebars in the full left position . Lock the handlebars. 3. Place a scissor jack directly under the left front brake caliper as shown in the illustration. To avoid damage to the caliper, place a protective piece of rubber (such as a piece of inner tube) between the caliper and the jack. Wind up the jack until the front wheel is approximately 15 mm off the ground. 4. Measure the distance from the secondary master cylinder piston mounting bolt to the edge of the secondary master cylinder body (rod length of the secondary master cylinder). Record this measurement . • If the measured length is 30.3 mm, replace the PCV per the Service Manual. (This length indicates the unit’s secondary master cylinder is fully stroked, which means there is no hydraulic brake pressure acting on the PCV.) After replacing the PCV, proceed to the IDENTIFICATION section of this Service Bulletin. •If the measured length is longer than 30.3 mm , proceed to step 5 below. • INSPECTION/REPAIR PROCEDURE Record this measurement. Pump the rear brake pedal four times.
GL1800/A #16 ©2005 American Honda Motor Co., Inc. – All Rights Reserved 3 of 6 FEBRUARY 2005 5. Wait 30 minutes. Do not disturb the motorcycle in any way during this time. 6. Measure the distance again from the secondary master cylinder piston mounting bolt to the edge of the secondary master cylinder body (rod length of the secondary master cylinder). •If the measurement has decreased more than 1 mm from the measurement you recorded, proceed to step 7 below. •If the measurement is within 1 mm of the measurement you recorded, the PCV is OK. Proceed to the IDENTIFICATION section of this Service Bulletin. 7. Check the PCV for leakage. • If the PCV is leaking , replace the PCV per the Service Manual. After replacing the PCV, proceed to the IDENTIFICATION section of this Service Bulletin. • If the PCV is not leaking , you must diagnose the brake system problem before proceeding. After you have diagnosed and repaired the brake system, proceed to the IDENTIFICATION section of this Service Bulletin. NOTE: Any brake system problem not related to the PCV that is found while performing this Service Bulletin is not covered by this Safety Recall. If the motorcycle’s original factory warranty is still in effect or under HPP, file a normal warranty claim. If the unit is outside its factory warranty period or HPP coverage, contact TechLine for goodwill consideration. 8. Verify proper front and rear brake operation by pumping the front brake lever and rear brake pedal before riding the motorcycle

2001-2003 GL1800/ A ECM Replacement/ Cooling System REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
Install the new ECM, then reinstall the cruise/ reverse control module in the reverse order of removal. NOTE: When you start the vehicle – after completing ALL procedures – the new ECM will require initialization . To initialize the new ECM, perform the following procedure: • Start the bike and allow it to warm up to normal operating temperature and remain at idle for at least 90 seconds . Do not operate the throttle during this time; if you do, the ECU will not initialize properly and the process will need to be repeated. 5. Proceed to the Cylinder Head Inspection section below. Use the Cylinder Head Inspection Kit for the Cylinder Head Inspection procedure. Use the kit for each GL1800/A you inspect. Do NOT dispose of kit items. 1) 19X20 mm cap (2) (cap B) 2) 8X15 mm cap (cap A) 3) Hose plug 4) Bottle/cap w/feed hose 5) Harness clips (10) 6) Harness tape 7) Inspection mirror A limited number of additional Cylinder Head Inspection Kits are available: call TechLine at 800-421-1900, ext. 1 if you need one. Kit contents are NOT available separately as parts. NOTE: • The following late ’03 models do not have to have their cylinder heads inspected: • Perform the following procedure with the engine at room temperature. • Both Left and Right cylinder heads must be inspected. • Use the Cylinder Head Inspection Kit for the following procedure. 1. Remove the front lower fairing. (See S/M, 2-6) 2. Remove and suspend the rear brake reservoir, being careful not to stress the brake hose. (See S/M, 15-A-8) CONNECTOR B (22-GRY) CONNECTOR C (6-BLK) CONNECTOR A (22-BLK) ECM (ENGINE CONTROL MODULE) 1 2 3 4 5 6 7 Late ’03 (Non-ABS): after VIN 1HFSC470*3A204632 Late ’03 (ABS): after VIN 1HFSC474*3A201020 Cylinder Head Inspection Kit Cylinder Head Inspection

Incoming search terms:

Incoming search terms: