manufacturers distributor buyer importers business development exports metal

You search Auto repair manual PDF manufacturers distributor buyer importers business development exports metal, if there are search results will appear below. If search results do not exist, please search by others keyword.





BILLET ALUMINUM DISTRIBUTOR WITH ELECTRONIC ADVANCE AND ADJUSTABLE REV LIMITER FOR 1936-69 HARLEY BIG TWIN MOTORCYCLES INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
ELECTRICAL SYSTEM A 12 volt electrical system is required. Check that the charging system is working properly and not producing over 16 volts. DISTRIBUTOR CLAMP A 1966-69 style distributor clamp (original or aftermarket) is required. MODULE This distributor uses an Accel Single/Dual Fire Ignition module part number 35496. See the enclosed form “Instruction Sheet Single/Dual Fire” for instructions on wiring, adjusting the rev limiter and selecting an advance curve. COIL(S) A coil(s) with a total primary resistance of 2 to 4 ohms is recommended. INSTALLATION Step 1 Turn the ignition switch to the off position. Rotate the engine until it is on the compression stroke for the front cylinder. Continue to rotate the engine until the TDC mark is visible through the timing hole. (see repair manual if necessary). Step 2 Remove the existing distributor if still in the engine. Step 3 Remove the two button head screws from the top of the Mallory distributor. Pull the top cover off the distributor. Remove the two hex standoffs and pull the module and upper housing off the distributor base assembly. Adjust the switches on the module for the desired advance curve and rev limit. FORM 1627 07/08 Step 4 Install the distributor base assembly in the engine with the screw holes and shutter wheel positioned as shown in Figures 1 and 2. It may be necessary to pull the distributor out, turn the shaft and reinstall to get the shutter wheel at the approximate angle shown. The slots should be at about the11 o’clock and 7 o’clock positions. The screw holes should be at the 9 o’clock and 3 o’clock positions. Step 5 Install the distributor clamp and tighten the clamp bolt lightly so the distributor can still be rotated. Step 6 Set the upper housing on the base assembly as shown in figure 3. (The upper housing will only install one way because of the locating screw) Rotate the base assembly slightly if necessary so that the slot in the shutter wheel lines up with the slot in the upper housing. Tighten the distributor clamp

Incoming search terms:

HONDA CB1000R AKRAPOVIC SLIP-ON EXHAUST SYSTEM REMOVAL And Installation instructions

0

Filed Under (Honda) by admin on 01-11-2010

download
1. Put the motorcycle on a side stand, we recommend a racing stand. Make sure, that surface is solid and flat. 2. Untighten the bolt on the metal clamp at the muffler – collector joint, unscrew the bolts from the muffler brackets, and remove the muffler (Figure 1, 2, 3, 4). T-handle 8mm wrench T-handle 12mm wrench T-handle 13mm wrench T-handle 10mm swiveling wrench T-handle 12mm swiveling wrench T-handle 3mm three hexagon key wrench T-handle 5mm three hexagon key wrench T-handle 8mm three hexagon key wrench Combination 13mm wrench Combination 17mm wrench Spring puller Figure 1 Figure 2 Figure 3 Figure 4
NAV – 401 3 Figure 7 Figure 8 Figure 9 Figure 10 3. Remove the metal collar and the rubber damper from the lower stock muffler bracket (Figure 5, 6). 4. For open slip-on only: for easier dismount of stock collector unscrew the bolt from the water cooler hanging bracket and slightly remove the cooler – do not disconnect the cooling system tubes! (Figure 7) , loosen the header tubes flanges (Figure 8) , untighten the bolts of the metal clamps A from stock collector – header tubes joint and then unscrew the bolt from the collector bracket (Figure 9, 10). Make sure not to damage the cooling fins of the cooler during this process. Figure 5 Figure 6
NAV – 401 4 5. For open slip-on only: Unscrew the lambda sensor and remove the stock collector (Figure 11, 12). Remove the metal collar and the rubber dampers from the stock collector bracket (Figure 13). INSTALLATION OF THE AKRAPOVIC SLIP-ON EXHAUST SYSTEM: 1. Unsrew the bolts and remove the right foot peg. Assemble the additional Akrapovic metal bracket, reinstall the foot peg and tighten the bolts (Figure 14, 15, 16, 17, 18, 19)

Aprilia RSV4 Exhaust Systems Installation instructions

0

Filed Under (Aprilia) by admin on 26-10-2010

download
REMOVAL OF STOCK EXHAUST SYSTEM 1. 2. 5 Figure 3 Figure 4 Remove the metal collar and rubber damper from the stock muffler hanging bracket (Figure 3, 4). 3. 6 Unscrew the marked bolts and remove the plastic fasteners from the left and right side of the cowling (Figure 5, 6). 4. Figure 5 Figure 6 7 Unscrew the marked bolts and remove the lower part of the cowling (Figure 7). 5. Figure 7
8 Figure 8 Figure 9 Coat the bolt and interior of the metal clamp with spring hook whit Akrapovič anti-seize lead-free copper paste (black tube) and correctly install it onto the stock collector. Hand tighten the bolt (Figure 9, 10). WARNING: use anti-seize copper paste on bolt threads and interior of the metal clamp! 2. 1. Coat the bolt and interior of the metal clamp with Akrapovič antiseize lead-free copper paste (black tube) and correctly install it onto the link pipe (Figure 8). WARNING: use anti-seize copper paste on bolt threads and interior of the metal clamp

Incoming search terms:

Edelbrock Nitrous Systems Digital RPM Window Switch USER MANUAL

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Programming the RPM The engine application and rpm activation points are easily selected through push buttons on the LED panel. This Switch can be programmed for a variety of engine and ignitions as shown below. 1-Cylinder This program is used for individual coil per cylinder systems (such as GM LS-1 engines, or ’99-Up Mustangs) 2-Cylinder This is for ignitions with coil packs that fire two cylinders at the same time (waste spark systems) 2-Cyl. Odd Use on coil pack ignitions that are on odd-fire engines such as a Viper V-10 or Harley-Davidson motorcycle. 4-Cylinder Typical 4-cylinder engines with a distributor. 6-Cylinder Typical 6-cylinder engines with a distributor. 6-Cyl. Odd Typical 6-cylinder odd-fire engines with a distributor. 8-Cylinder Typical 8-cylinder engines with a distributor. 1.2 Push Button LED Panel The rpm activation points and cylinder select are programmed through the push buttons on the LED panel (Figure 1) . Press the Mode button, and notice that the indicator point above the On RPM lights. When that point is on, you can scroll the rpm value up or down with the arrows on the left of the panel. Once your On rpm is set, push the Mode button until the Off RPM point lights, then set the off rpm point. Note that if the rpm point is not changed within 2-seconds, the screen returns to the current rpm reading (zero when the engine is not running). After setting the On and Off points, press the Mode button to program the Cylinder Select Valve (default is for 8-cyl.

DUCATI 900 SuperSport Engine performance And technical specification

0

Filed Under (Ducati) by admin on 11-11-2010

download
Displacement: 904 cc Bore: 92 mm Stroke: 68 mm Max. power: 75 hp at 7000 rpm Max. torque: 80 Nm at 5000 rpm Max. velocity: 220 km/h Pass-By noise: 82 dB(A) Homologation: 1992 Main Targets of Development Today’s motorcycle market requests more powerful engines, however, legislative noise and pollution limits are becoming more severe. In order to reduce development cost only small modifications were allowed. Entirely new designs of technical components (i.e. cylinder head) had to be avoided. In additon, the complete development had to be finished in a relatively short time of about three months. The most important targets of development were: better engine performance: – more max. power: +5 hp – more torque at low rpm lower noise emission: -2 dB(A) 80 dB(A) (89/235/CEE) change from carburettor to fuel injection system Figure 1, Ducati 900 SS
3 Engine performance calculation with WAVE A complete model of the new engine concept (fuel injection) with actual intake- and exhaust geometry allowed us to set up a reference engine-cycle-simulation model for further optimization. The most important parameter-variation during the cycle-studies to improve volumetric efficiency were: intake duct length valve timing constant or even lower exhaust backpressure Figure 2 shows the improvement in calculated engine performance due to different intake-duct length and modified valve timing. Figure 3 gives an example of accuracy of the calculation results compared with measured data of engine performance with new intake-duct length. Figure 4 illustrates the final engine performance with modified valve-timing, intake-duct length and new exhaust silencer. A comparison of measured performance data between the original and the redesigned engine gives shows the improvements in terms of maximum power and torque at low rpm.

Integral ABS and ASC – new Riding Dynamic Control Systems for BMW Motorcycles

0

Filed Under (BMW) by admin on 16-11-2010

download
Entering its next generation, BMW Motorrad Integral ABS is taking a quantum leap in the process of evolution, advancing from a stand-alone solution acting only on the brakes into a fully networked all-round system. Offering the new generation of Integral ABS, BMW Motorrad provides the foundation for additional dynamic riding control systems with a reduction in technical requirements and features. And following the customer’s wishes, this new generation also opens up the option in future for further-reaching rider assistance functions. The first step in this direction is BMW Motorrad ASC Automatic Stability Control available as of 2007. This system serving to control drive spin on a production motorcycles is being introduced as an optional extra on the touring models in the BMW K and Boxer Series. Once again, therefore, BMW is acting as the pioneer in the introduction of advanced safety technologies on the motorcycle. This further enhances the leadership which BMW Motorrad has shown in the area of active safety for more than 15 years. Choosing the right development partner for both systems, BMW Motorrad obviously had to focus on that partner’s specific competence in control technology and the networking of functions within the vehicle. In recent years, major car suppliers have become aware of the technical challenges presented by the motorcycle with its specific riding dynamics and the growing potential for motorcycle control systems in the market. The decisive point in preselection of the development partner was the willingness and ability to develop specialised solutions suitable for use on BMW motorcycles. So taking this into account, joint development of the new generation of ABS brake technology started together with Continental-Teves in early 2003. Integral ABS. BMW Motorrad’s new Integral ABS technology has been developed separately from the previous system and the entire layout of the system has been newly conceived from the ground up. Capitalising on progress in technology in both hydraulics and electronics, the development engineers have succeeded in simplifying the architecture of the system while at the same time enhancing its functions to an even higher standard. The result is supreme stopping power and very short stopping distances even without electrical power assistance on the brakes.

Express ATVS -250cc Cobra Setup/ Installation Manual

0

Filed Under (Cobra) by admin on 10-11-2010

download
Unpacking your Cobra Installing the front shock Installing the front tires Installing rear shocks Installing the rear tires Installing seats and harnesses Steering wheel installation Roll cage installation Safety checks / Adjustments General maintenance Unpacking your Cobra First off you should pull the carton off from your new 250 Cobra cart. Inspect the cart thoroughly to make sure that your new Cobra has not been heavily damaged. You will notice that the product has a metal frame holding it in place; you may want to start removing bolts from the shipping steel frame. The next step is to remove the metal frame and lift it off of the cart. Remove any of the metal frame that may afford resistance when working on the cart it self. Be careful the metal frame may be heavy and sharp. Now would also be a good time to inspect your Cobra a little more thoroughly. In the box with the Cobra you should have found a box containing miscellaneous hardware. Installing the front shock Using some of the bolts you found in your box, install the front shocks sliding the bolt through the brackets and tighten the nut down. Next, you will need to place the ball head into the turning arm, then tighten the castle nut and insert a cotter pin so that the castle nut doesn’t loosen and become a hazard. Installing the front tires
Find the front tires and place them on the front hub and place the lug nuts on the studs. Tighten them down. Make sure that all of the lug nuts are on tightly. Installing the rear shocks Moving to the rear of the Cobra you will notice the rear shocks are not inserted. Place the rear shocks into the bracket on the rear of the Cobra. Slide one of the provided bolts through the bracket and shock eyelet and tighten the bolt down. Installing the rear tires Now that the shocks have been placed properly you can install the rear tires, place the tires onto the axle then place the rear rim lined up onto the axle and tighten the provided castle nut down. Place the cotter pin through the axle and bend off to the side. This is so the castle nut does not loosen under load. Installing the seats and harnesses
(The arrow points to an example of where the seat bolts mount) Find the two racing seats shipped in the box with the Cobra. You will need to affix them to the frame by sliding the bolts up through the bottom of the frame. This can be tricky so have patience. Once both seats have been placed in the cart and tightened find the harnesses. Once found the harnesses mount to a bracket behind the seats. Place a bolt through the bracket and bolt the harnesses down tightly. Installing the steering wheel Find the steering wheel and place it onto the steering wheel mount. Grab the six small screws and place them through the steering wheel and mount, tighten them down but also make sure the top of the wheel is facing up. Installing the roll cage

Harley- Davidson Bagger Audio factory service manual for removal

0

Filed Under (Harley Davidson) by admin on 03-04-2012

download
POWER & SPEAKER HARNESS INSTALLATION- (Read electrical connections prior to connecting center power and ground wires) 1. Disconnect battery (negative cable first!) 2. Remove outer faring cover 3. Route long speaker wires from fairing area through tank channel to seat area. 4. Route one pair of speaker wires under each fender strut support; purple and purple and black wires to the right and green and green and black wires to the left. AMPLIFIER INSTALLATION- 1. Factory installed electronics will determine suggested placement of amplifier. 2. Position and attach amplifier to outer fairing support bars with supplied wire ties. (Electra/Ultra/Street Glide) BAGGER AUDIO™ LIDS INSTALLATION- Detach factory lid by removing the 2 screws holding the factory strap to inner lid and 5 small torque screws holding lid to factory latch assembly. (Consult factory service manual for further instructions) Remove metal strap from behind factory seal (This is the metal strap that the previous 5 small torque screws were removed from) Position metal strap in same location on your new lid. (If you purchased your product unpainted, you must install the supplied seal to your finished lid) Reattach BAGGER AUDIO™ LIDS by installing the 5 small torque screws in the same location as on the factory lid. (We suggest that you have an assistant hold the lid in place while attaching your new lids) Replace factory nylon Hinge straps with new nylon straps supplied in kit. Use metal straps and machined screws to secure the nylon hinge straps. 
 Place a small bead of silicone on the inside rim of the speaker basket to create a watertight seal between the inside of the lid and the speaker. 
 Install speaker into the bottom of the lid (not through the top opening) with supplied stainless screws and washers (4 per lid). Be sure to center speaker in lid opening to ensure proper speaker grill placement. Install speaker with terminals facing toward the front of the lid. One 1/4″ hole must be drilled in each bag. Holes can be positioned at the ownerʼs discretion. Place rubber grommet in drilled hole before running wires

HONDA CBR 1000 RR AKRAPOVIC SLIP-ON & SLIP-ON STREET LEGAL EXHAUST SYSTEM REPAIR

0

Filed Under (Honda) by admin on 17-11-2011

download
INSTALLATION OF THE AKRAPOVIC SLIP-ON STREET LEGAL SYSTEMbinstalling the independent link pipe:m1. onto the stock collector properly install the metal ring for attaching the spring (Figure 27, 28) 2. install the metal clamp onto the Akrapovic independent link pipe (Figure 29) 3. slide the Akrapovic independent link pipe onto the stock collector; do not tighten the metal clamp (Figure 30) 4. attach the spring (Figure 31) 5. make sure the link pipe is not touching the frame and other parts installing the muffler: 1. correctly position the carbon-fiber clamp and slide it onto the muffler. WARNING: open the clamp to slightly wider than the diameter of the outer sleeve of the muffler – do not scrape it along the muffler outer sleeve! Do not fully tighten the bolts of the clamp (Figure 32) 2. position the muffler correctly and slide it onto the outlet side of the link pipe (Figure 33) 3. position and attach the springs (Figure 34) 4. tighten the carbon-fiber clamp onto the stock chassis hanging bracket on the frame (both sides of the motorcycle (Figure 35, 36, 37) 5. tighten the metal clamp at the independent link pipe – stock collector connection (Figure 38) 6. tighten the bolts of the carbon-fiber clamp. 7. reattach the stock heat shield (Figure 39, 40)8. reattach the rider’s footrest bracket (Figure 41) 9. make sure the muffler is not touching other parts of the motorcycle 10. reattach the license plate holder and turn signal lamps (Figure42, 43)11. reconnect the electrical leads for the rear light and reattach the fastback and both seats

SUZUKI MOTORCYCLES Gsxr 600, Gsxr 750, Gsxr 1000 teak the lead

0

Filed Under (Suzuki) by admin on 12-11-2010

download
The launch of the sixth generation of Gsxr marked a shift in Suzuki’s emphasis on two fronts. One, the Gsxr 1000 now took the upper hand in the development stakes. Historically, the Gsxr 750 led the march-arriving first, gaining the most recent technology, absorbing the lion’s share of corporate pride-but by 2003 the Gsxr 1000 was in the lead. Two, the Gsxr 1000 represents another, more subtle shift for Suzuki engineering, in which the designers-the lucky guys who get to clothe these amazing machines-have more freedom of expression. With this generation, the designs turned edgier, sharper, more aggressive looking than ever. What’s more, the Gsxr 1000 K3 would be the proving ground for a host of changes brought to the Gsxr 600 and Gsxr 750 for 2004. In fact, nearly every upgrade to the smaller bikes appeared on the Gsxr 1000 a year before. But the real impetus for driving the Gsxr 1000 to the head of development and, indeed, shortening its development cycle was competition both on the track and in the showroom. For the track, it was understood that Superbike racing would revert to allowing 1000 cc four-cylinder bikes in place of the 750s that had been the limit since 1982. In 2002, Yoshimura and Mat Mladin barely lost the AMA Superbike crown to Nicky Hayden aboard the Honda RC5!. But it would be the RC’s swan song of competitiveness with the change to 1000 cc fours. To keep speeds in check, the AMA Superbike rules would require 1000 cc fours to have some additional limitations compared to the twins and triples. For example, “Cylinder heads may be ported and machined, but altering of valve angles will not be permitted; aftermarket valves, springs, retainers, and other valve-train components will be permitted; valves must be stock size and same basic material as original equipment; aftermarket camshafts will be permitted, but earn lift and resulting valve lift must be no greater than stock. “In addition, the “stock crankshaft must be retained, The only allowable modifications are balancing, polishing of bearing surfaces and attachment of accessory drives. Homologated transmission gear sets (one optional set of ratios per approved model) will be permitted. Optional sets will be price-controlled and must be available to any legitimate AMA Superbike competitor. Homologated fuel-injection throttle-body assemblies (one optional type per approved model) and aftermarket airboxes will be permitted. Modifications to throttle bodies will not be permitted. Optional throttle bodies will be price-controlled and must be available to any legitimate AMA Superbike competitor.” The thinking was simple: keep the liter bikes from sucking through massive throttle bodies, and the horsepower might not (and, it was hoped, would not) go through the roof. In preparation for racing, Suzuki moto wanted to make a host of small changes to the Gsxr 1000, but its motivation was also to keep the bike at the forefront of open-class street bikes. Suzuki engineers knew that Honda and Kawasaki were readying all-new models-the CBR 954 RR and the ZX 9 R had long since been vanquished-and rumor had it that Yamaha was ready with yet another push with the R1.It was the right time to make alterations to the Gsxr 1000. Heading the list was, as one might expect, a revised engine.

Incoming search terms:

Incoming search terms: