manufacturers suppliers secretaries managers ceo of fuel filter gas inline petrol oil tank fuel filters replaces mini small engine lawnmower motorcycle mail

You search Auto repair manual PDF manufacturers suppliers secretaries managers ceo of fuel filter gas inline petrol oil tank fuel filters replaces mini small engine lawnmower motorcycle mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





HARLEY DAVIDSON SOFTAIL OIL COOLER KIT WITH CHROME OIL COOLER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
INSTALLATION 1. See Figure 1. Install the oil cooler (2) to the frame with three clamps (4), three socket head screws (1), three nuts (5) and six washers (3) from the kit. Orient the clamps flat side forward and on the forward side of the oil cooler. Tighten the three oil cooler mounting screws to 96-120 in- lbs (10.9-13.5 Nm) . 2. See Figure 2. Remove the spin-on oil filter and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter and adapter. 1 3 4 4 4 3 5 2 is03387 1. Socket head screw (3) 2. Oil cooler 3. Washer (6) 4. Clamp (3) 5. Locknut (3) Figure 1. Oil Cooler Clamp Installation NOTE The oil cooler adapter assembly has two flanges protruding out of the back side. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 3. See Figure 3. From the kit, install the oil cooler adapter gasket (3) onto the oil cooler adapter assembly (1). The oil cooler adapter assembly flanges should be aligned so it is installed into the oil adapter cooler gasket cutout as shown. NOTE Due to the locating flanges, the oil cooler adapter assembly and gasket will only install properly in one position on the oil filter mounting surface. 4. See Figure 3. Install the oil cooler adapter assembly and gasket onto the oil filter mounting surface of the engine with the mounting fitting (2). Ensure adapter locates properly in the mounting surface. Ensure the raised lip of the mounting fitting faces the adapter assembly. Tighten mounting fitting to 12-16 ft-lbs (16.3-21.7 Nm) .NOTE Slide hose clamps from the kit onto the hoses prior to installa- tion. 1 2 is00754 1. Oil filter adapter 2. Oil filter seal surface Figure 2. Stock Filter Mounting Adapter 1 2 3 is00761 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket Figure 3. Install Oil Adapter 5. See Figure 5. Obtain the left side cooler hose (4) and right side cooler hose (5) from kit. Follow the markings on hoses to connect onto the oil cooler and oil cooler adapter, as shown. 6. Fasten hoses to oil cooler adapter and oil cooler with worm drive clamps (6). Tighten clamps to 8.0 in-lbs (0.9 Nm) . 7. Lubricate a new oil filter’s seal with new engine oil. Thread filter on until seal touches mounting surface, then turn an additional 1/2 to 3/4 turn. NOTE Position the clamps to avoid interference with oil filter installation. Check that hose routing is clear of the oil filter and sharp edges. The hoses must be free of bends or kinks that could obstruct oil flow. 8. Ensure all cables and harnesses are clear of the oil cooler adapter, in order to prevent wear. 9. Thoroughly clean the oil cooler of all dirt, grease and wax with isopropyl alcohol. Use the alcohol to clean the chrome oil cooler cover as needed. Allow to dry. is00745 Figure 4. Apply Sealant Inside Chrome Cover 10. See Figure 4. Apply sealant to the inside of the chrome cover as shown, at the upper and lower corners. NOTES Be careful to avoid getting sealant on the oil cooler cooling fins. Do not operate the motorcycle for 24 hours to allow the sealant to fully cure. 11. Slip the cover over the oil cooler. Remove any excess sealant from the front and back of the oil cooler. Hold the cover firmly in place for one minute. System Flow Test 2005 & Later Models or Models with Later Style Dipsticks Oil level cannot be accurately measured on a cold engine. For pre-ride inspection, with motorcycle leaning on jiffy stand on level ground, oil should register on dipstick between arrows when engine is cold. Do not add oil to bring the level to the FULL mark on a COLD engine. (00185a) 2004 & Earlier Models

Incoming search terms:

Triumph Oil Filter Mount installation

0

Filed Under (Triumph) by admin on 29-10-2010

download
The Norton filter adapter is then bolted to the rear piece, oil hoses are added, an oil filter is screwed into place, and the assembly is offered to the bike. With the bike supported by straps up on a lift, it will be easy to loosely mount the front clamp section in place and slide the whole assembly up the frame tube. In order to miss the center stand, the filter will need to be as high as possible without the grease nipple striking the top of the adapter. As it ends up, there is “sweet spot” where both the nipple and the stand miss the oil filter by about an 1/8 inch. Tighten the mount down when you find that place. I found that the Norton filter adapter is best plumbed using 5/16 ID black neoprene fuel hose. The spigots on the adapter are 3/8 inch, but it is better to stretch the hose over these that to use easier fitting 3/8 ID hose and then try to shrink it onto the Triumph’s smaller metal oil lines. There will simply be fewer oil leaks using the smaller hose. Be sure that you plumb the filter into the oil line that returns engine oil back to the oil tank. The Triumph oil pump cannot be counted on to create enough vacuum to suction highly viscous motor oil through a very fine filter during cool temperatures. Trying to place the filter on the oil line feeding the engine will quickly result in massive engine damage. It is always better to have the oil pump pushing oil through the filter, and the only way to have RF Whatley, Suwanee, GA 5 Jan 2008 that is to use the return oil line. On all “unit-construction” Triumph engines, the rear-most oil port is the engine oil return. Other Notes • It is generally considered that adding an oil filter will at least quadruple the life of a British motorcycle engine. These motors, which were for the most part perfected in the 1950′s, were designed to run on the older non-detergent oils. In the original design, the oil tank was the oil filter since all particulate debris in the oil settled to the bottom of the oil tank as sediment. All modern engine oils are high-detergent and tend to inhibit the formation of sediment. Therefore most of the fine abrasive in the engine oil continues to circulate unless a filter is added.

1999 Toyota Camry LE V6 Body and Interior Maintenance Record

0

Filed Under (Toyota Manuals) by admin on 03-10-2011

download
Action Date Mileage Day Cost (with tax) By Interval Notes Oil and Oil Filter Change 8/30/1999 2494 Monday$77.97 Dealer 2494Non-synthetic 5w-30 (Toyota dealer stock) Oil and Oil Filter Change 10/31/1999 5484 Sunday $30 Owner 2988.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 12/30/1999 8460 Thursday$30 Owner 2975.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/21/2000 11414 Monday $30 Owner 2953.3Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 4/22/2000 14479 Saturday$30 Owner 3065.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 7/4/2000 17339 Tuesday$30 Owner 2860.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 7/4/2000 17339 Tuesday$15 Owner 17339Purolator A24690 Air Filter Oil and Oil Filter Change 9/16/2000 20161 Saturday$30 Owner 2821.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Drain and Fill 10/27/2000 21913 Saturday$15 Owner 21913Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Transmission Drain and Fill 10/28/2000 21920 Sunday $15 Owner 7Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Oil and Oil Filter Change 11/19/2000 23066 Sunday $30 Owner 2904.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/11/2001 26062 Sunday $30 Owner 2996.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Flush 4/30/2001 28351 Monday$135 Dealer 2835113 Quarts Mobil 1 Dexron III Synthetic ATF – TransTech Flush Tires – Rotate 5/12/2001 28766 Saturday$0 Dealer 28766Tires – Rotate Coolant Flush 5/12/2001 28766 Saturday$112 Dealer 28766Toyota Red Coolant + MOC Flush (Extended warranty with service) Oil and Oil Filter Change 5/13/2001 28793 Sunday $30 Owner 2730.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 5/13/2001 28793 Sunday $15 Owner 11454Purolator A24690 Air Filter PCV Valve – Replace 5/26/2001 31083 Saturday$10 Owner 31083Toyota OEM PCV Valve Windshield Wipers – Replace 5/26/2001 31083 Saturday$10 Owner 31083Windshield Wipers – Replace Oil and Oil Filter Change 5/27/2001 31296 Monday $30 Owner 2502.8Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 9/15/2001 34374 Saturday$30 Owner 3078.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Tires – Replace 9/28/2001 34784 Friday$431.23 Dealer 34784 (4) Bridgestone RE950 Tires (2 of original tires had tread separation – ~30% tread remaining) Oil and Oil Filter Change 11/12/2001 37365 Monday $30 Owner

Incoming search terms:

YAMAHA V-Star 1100 Motorcycle Enhancements Remote Oil Filter Installation Manual

0

Filed Under (Yamaha) by admin on 10-11-2010

download
Removing Your Old Filter and Beauty Cover In order to install the new Remote Oil Filter Kit, you’ll need to remove the stock Yamaha “beauty cover” and the old filter and filter cover. Remove the engine parts necessary to access the stock filter as outlined in the V-Star owner’s manual. The parts should come off in this order: 1. Muffler assembly 2. Front exhaust pipe 3. Rear brake reservoir cover bolt and brake cover (the reservoir should not be removed, it can remain in place and be moved aside as needed) 4. Right floorboard (this can be simply loosened, by loosening the two bolts underneath) With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. There are five Allen bolts holding the beauty cover (so named, because most of the cover just covers the chromed side of the engine There are five bolts holding the cover. Ignore the three on the “Yamaha” cap in the middle – these just hold the Yamaha cap to the beauty cover itself. One bolt is hidd – in this picture – just be the Yamaha ca en low p. The bottommost bolt on the beauty cover will likely leak some oil when you remove it – it holds on the inner oil filter cover. Once you remove the beauty cover, you can remove the oil filter cover, and the oil filter Keep these two “O” rings, you’ll need them for the remote kit Old oil filter. Toss it away; you’ll never need one again! Throw away the old filter, and carefully remove the orange and black “O” rings from the filter cover (see picture above). These two “O” rings will go on the new engine cap in the same order as on the old filter cover. “O” ring for bottom bolt. When the beauty cover and filter cover are removed, be sure not to lose the tiny “O” ring that the bottom bolt goes through. Preparing the Remote Oil Filter Kit Remove the orange and black “O” rings from the stock filter cover plate, and place them on the Remote Oil Filter Kit engine cap – black on the inside, orange on the outside – just like on the stock filter cover.

SPIN-ON OIL FILTER ADAPTER INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Place the motorcycle on its centerstand. Do this on a hard surface so the motorcycle will not easily tip. Do not do this on gravel or dirt. 2. Remove the air dam/lower cowl to gain access to the oil filter housing. Using a 12mm 6-point socket, remove the original oil filter bolt and housing. The engine will lose approx. ½ quart of oil when changing the filter. 3. Clean the engine surface behind the oil filter housing where the o-ring will seat. Install the adapter plate with the new o-ring supplied onto the threaded boss protruding from the engine with 0-ring side facing the engine. 4. Screw the hollow stud with the jam nut into the engine where the original filter bolt went. Note that the end with the longer portion of threads goes into the engine. Screw the stud in until it is finger tight. Check to be sure the o-ring on the back of the filter plate is sill in its groove. Tighten the jam nut with a 12″ crescent wrench. Be careful your wrench does not slip and marr the surface of the filter plate. Use approx. 15 to 20 lbs of force at the end of the wrench to tighten the stud. 5. YAMAHA VENTURES ONLY : The frame brace needs to be raised slightly to give you more clearance for a filter wrench when changing your filter in the future. This brace between the right & left frame rails directly over the filter. Loosen the four (2 per side) 8mm bolts (12mm wrench size) that have the long acorn nuts. After loosening the four bolts, you will notice that there is approximately ¼” slack in these bolts. Lift the brace up as far as possible & retighten the bolts. 6. Coat the new filter gasket with oil. Spin the new filter onto the adapter plate until the gasket makes contact, and then tighten ¾ of one turn. This must be done each time you install a new filter. Use a filter wrench if necessary. Be sure your filter is tight! 7. Add ½ quart of oil or change the oil if you desire. Start the engine. Allow it to run for 30 seconds or more. Rev the engine to 4,000 rpm for 20-30 seconds. Shut the engine off & check thoroughly for any oil leaks.

BMW Motorcycle R1100 RT R1100 RS R850/ 1100 GS R850/ 1100R Repair Manual

0

Filed Under (BMW) by admin on 18-11-2010

download
Engine Connection Nm Nm Oil filter Oil filter 11 11 Oil drain plug 32 32 Oil pump Mesh filter basket to engine block 9 9 Oil pump cover 9 9 Pressure relief valve 35 35 Oil pressure switch 30 30 Oil cooler Oil cooler pipe to engine block 10 10 Cooling oil line – banjo screw 25 25 Cooling oil line – banjo screw with oil vent valve 25 25 Oil lines to oil cooler 25 – Oil cooler to holder 9 9 Oil cooler return line to engine block 35 35 Oil cooler feed line to frame 20 20 Oil cooler feed line to engine block 25 25 Screw-in union for oil cooler connection at engine block 35 35 Clean threads and apply Loctite 603 to inner and outer threads and in the contact face area Oil cooler hose at oil thermostat – 40 Cylinders Tightening sequence M 8 screw 20 20 M 6 screw 9 9 Chain guide rail pivot screw 18 18 Timing chain Chain tensioner 32 32 Connecting rod Big end cap Joint torque 20 20 Additional wrench angle 80° Crankcase Tightening sequence: M 10 screw (oiled) 45 45 M 8 screw (oiled) 20 20 M 6 screw Engine electrical system Connection Nm Nm Starter motor to engine 20 20 Starter cover to gearbox housing 7 – Positive lead to starter motor 10 10 Alternator to alternator support cover 20 20 Tensioning and retaining strap at alternator 20 20 Spacer at alternator 20 20 Positive lead to alternator 15 15 Belt pulley at alternator 50 50 Belt pulley to crankshaft 50 50 Poly-V belt preload 8 8 Spark plug 20 20 13 Fuel preparation and control Temperature sensor on engine block 25 25 16 Fuel tank and lines Fuel tank to rear frame 22 22 Fuel pump assembly to tank 6 6 18 Exhaust system Muffler to footrest 35 35 Manifold to cylinder head (with strap) 22 22 (with jacket pipe) 18 18 Muffler to support plate for center stand 20 20 Clip on muffler 50 50 Grease clamping face with Never Seez Oxygen sensor (lambda probe) to muffler 55 55 Grease with Never Seez

Incoming search terms:

BUELL ACCESSORY GAS CAP KIT INSTALLATION MANUAL

0

Filed Under (Buell) by admin on 29-03-2011

download
Installation NOTE When performing the following Steps, use the Fuel Tank Vent Valve Installation Kit (Part Number 91432-96Y). This kit consists of: * Fuel Tank Vent Valve Installation Aid * Fuel Tank Vent Valve Fitting Socket To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect battery cables, negative cable first. An open flame or spark may cause a fuel tank explosion if all traces of fuel are not purged from the tank. Use extreme caution when servicing fuel tanks. Gasoline is extremely flammable and highly explosive. Do not smoke or allow open flame or sparks anywhere in the area when working on fuel system components. Inadequate safety precautions could result in death or serious injury. 2. Remove gas cap. 3. Carbureted Models: Drain fuel tank. Disconnect hose clamp and fuel supply hose from fuel supply valve and drain fuel into suitable, clean container. See applicable Service Manual, Section 4 for complete, detailed procedure. Fuel Injected Models: Relieve pressure from fuel system. See applicable Service Manual, Section 4 for complete, detailed procedure. Drain fuel tank. a. Using suitable external fuel pump, such as a Gas Caddy, pump fuel from tank and into a suitable, clean container. b. See instructions for external fuel pump for correct use. 4. See Figure 1. Cut cable tie securing vent hose to fitting and remove vent hose from fuel tank. Even with the fuel tank completely drained, a small amount of gasoline may leak from the bore when the fuel supply valve is loosened or removed. Thoroughly wipe up any fuel immediately and dispose of rags in a suitable manner. Gasoline is extremely flammable and highly explosive. Inadequate safety precautions could result in death or serious injury. 5. If the fuel supply valve requires cleaning or repair, refer to applicable Service Manual, Section 4, for complete, detailed procedures. 6. See Figure 1. Remove the fuel filler cap and O-ring. 7. Remove the eight self-tapping screws from fuel clamp flange and remove fuel cap flange

HARLEY DAVIDSON LCD OIL TEMPERATURE/ LEVEL DIPSTICK INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
LCD DIPSTICK INSTALLATION 1. Remove the original equipment (OE) dipstick from the filler neck. 2. Non-threaded Dipsticks: Lightly oil the O-ring on the new LCD dipstick. Orient the dipstick so that the display window is horizontal and readable from left to right, with the Bar and Shield logo to the left (towards the rear of the motorcycle). Push the dipstick straight into the filler neck until it seats. 3. For threaded dipsticks: Lightly oil O-ring and screw into the transmission like OE dipstick. If the orientation of the display is unsatisfactory when fully seated, refer to Adjusting the Display Angle later in these instructions. NOTE To be sure of correct readings, the dipstick MUST seat firmly against the flange. LCD DIPSTICK USE AND CARE Removing the Dipstick The dipstick assembly must be removed from the filler neck to add oil or to service the internal battery. Displaying the Oil Temperature and Level See Figure 1. Press and release the rubber button on the front face to display the temperature of the oil in the oil tank in degrees Fahrenheit (°F), and the oil level. The display will automatically shut off after approximately ten seconds. Do not overfill oil tank. Doing so can result in oil carryover to the air cleaner leading to equipment damage and/or equipment malfunction. (00190a) NOTES Oil level cannot be accurately measured: • on a cold engine • with the motorcycle upright • with the engine running NOTE Oil level on 2000 through 2004 Softail models with the original dipstick is checked with the motorcycle standing upright (not leaning on the jiffy stand). THIS IS NOT THE CASE with the LCD oil temperature/level dipstick. For all 2000 and later Softail models, oil level inspection must be done with the motorcycle LEANING ON the jiffy stand, on level ground. For pre-ride oil level inspection: With the motorcycle on level ground, RESTING ON the jiffy stand : •The oil level should be as indicated in Figure 1, display 4 through 8 (bars showing oil level, and “COLD OIL” message followed by flashing oil temperature) when the engine is cold. DO NOT ADD OIL to bring the level to the FULL mark on the dipstick of a COLD engine. •If the oil level indicates as in display 9 (animated level bars, followed by an “888 NO SENSOR” code), the wires inside the dipstick may be disconnected or damaged. Refer to Replacing the Battery later in these instructions to separate the dipstick upper and lower assemblies. If the small plug next to the battery has become dislodged from the receptacle, plug it in. If a visible wire is damaged, a repair can be attempted. If no damage is visible, the dipstick is damaged internally and should be replaced. For oil level inspection at operating temperature: Ride the motorcycle until the engine is at normal operating temperature. Idle for 1-2 minutes with the motorcycle on level ground, RESTING ON the jiffy stand (except Softails) , turn the engine OFF.

Incoming search terms:

HARLEY DAVIDSON FLUSH-MOUNT LED FUEL GAUGE AND GAS CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove stock gas cap from fuel tank. 2. Clean and wipe inside surface of fuel tank filler cup, O-ring seal surface, and trim ring adhesive surface with a mixture of equal parts of isopropyl alcohol and distilled water. 3. See Figure 1. Install gas cap into fuel tank. is00407 Figure 1. Screw in Gas Cap is00466 Figure 2. Note Position of Arrow on Trim Ring 4. Push down on gas cap and rotate clockwise one-eighth of a turn to lock. To unlock, push down on gas cap and rotate counterclockwise one-eighth of a turn. 5. See Figure 2. Before removing adhesive backing, note position of arrow on inside diameter of chrome trim ring. NOTE As you rotate trim ring, you will see gaps between trim ring and fuel tank. Rotate trim ring to position that best eliminates gaps between fuel tank and trim ring. Rotation of trim ring should be minimal. 6. See Figure 3. With the arrow pointing toward front of motorcycle, rotate chrome trim ring slightly to determine best position of bottom chrome trim ring to contour of the fuel tank 7. See Figure 4. Mark position of chrome trim ring with masking tape or grease pencil. 8. Carefully cut masking tape with a hobby knife making sure not to scratch chrome trim ring or paint surface on fuel tank. 9. Peel off adhesive backing from chrome trim ring. 10. Using gas cap to center and masking tape (or grease pencil mark) to align, press chrome trim ring firmly into position for about ten seconds. 11. Peel off masking tape (or remove grease pencil mark) from chrome trim ring and fuel tank. 2 1 is00414a 1. Masking tape 2. Cut masking tape Figure 4. Align Trim Ring and Press into Place NOTE Allow adhesive trim ring to cure for about 5-7 minutes before you continue with kit installation. Install Flush-Mount LED Fuel Gauge 1. Remove the seat following the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove stock fuel gauge. Refer to service manual for instructions. 4. Insert wires down tube of fuel tank from LED fuel gauge. 5. See Figure 5 and Figure 6. Insert LED fuel gauge in the fuel tank cup

Incoming search terms:

Wildfire WFH 150-T Touring Scooter Specification And Owner's Manual

0

Filed Under (Wildfire) by admin on 29-11-2010

download
Engine Oil Replacement • Replace the engine oil after the first 50 miles or 1 hour with 5w50, 10w50 or 15W50 synthetic engine oil. Then replace again every 1,500 miles or 1 each year. Check oil level every 500 miles, add oil if needed. Changing the Engine Oil (1).Warm up the engine for a few minutes. (2).Stop the engine. (3). Place scooter on center stand. (4).Place an oil pan under the engine and remove the dipstick. (5).Remove the drain plug and drain the oil. Reach in drain hole, pull out filter clean and reinstall, after all oil drains out. (6).Reinstall drain plug. (7). Fill the engine with oil until the level is in the designated area on the dipstick. (8).Start the engine and check for oil leaks. If a leak is found stop the engine immediately and look for cause. Rear Wheel Oil Replacement • Replace the gear oil after the first 500 miles with 5W/50 synthetic engine oil. Replace the gear oil again every 4 months or every 2000 miles. • Replacing the Gear Oil (1).Put the scooter on the center stand (please see photo below) . (2).Place an oil pan under the gear case (please see photo below) . (3).Remove the oil filler bolt and the drain plug to drain the oil (please see photo below) . (4).Reinstall and tighten the drain plug. (5).Fill the gear case with oil (please see photo below) . (6).Reinstall the oil filler bolt. (7).Check for oil leakage. Cleaning Air Cleaner Be sure to check the air cleaner regularly. (1).Place the scooter on the center stand. (2).Unscrew and remove the left side panel. (3).Remove the air cleaner cover by removing the screws. (4).Take out the air cleaner by removing the screws. (5).Remove the air cleaner element and wash it gently, but thoroughly in solvent. Replace if damaged. (6).Squeeze out the excess solvent and dry it. (7).Apply oil to the entire surface of the air cleaner and squeeze out the excess oil. It should be damp but not dripping. (8).Install the air cleaner, cleaner cover, and left side panel. center stand 1 oil pan 2 3 oil drain plug oil pan 5 Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed.

Incoming search terms: