manufacturers suppliers secretaries managers ceo of snow beanies mail

You search Auto repair manual PDF manufacturers suppliers secretaries managers ceo of snow beanies mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





Kawasaki MULE 600 / 610 SNOW PLOW INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. PRELIMINARY: 1.1 Remove the six 6 mm. screws and plastic skid / splash shield from the bottom front of the vehicle frame. (These bolts and plastic skid / splash shield will not be reused snow plow mounting frame installed onto the vehicle.) 1.2 If the vehicle has the Kawasaki optional brush guard installed, it will have to be removed and then reinstalled after the snow plow mounting frame is installed. (The brush guard will fit with the snow plow mounting frame installed first.) 2. VEHICLE MOUNTING FRAME 2.1 Position the vehicle mounting frame (13) under the front of the vehicle so that the six holes (with pipe spacers) line up with the six 6 mm. threaded holes that the plastic skid / splash shield was attached with and the upper plate is through the large oval hole in the vehicle plastic fascia. Fasten loosely using 6mm. x 1.0mm. x 30mm. bolts (33) , 6mm. lock washers (35) and 6mm. flat washers (34). 2.2 Place a 5/16″-18 “U” bolt (36) around the front cross tube behind the plastic fascia and through each set of holes in the flange of the upper plate of the vehicle mounting frame (total of two “U” bolts). Fasten loosely using 5/16″flat washers (41), 5/16″ lock washers (40), and 5/16″-18 nuts (42). 2.3 Install a 5/16″-18 “U” bolt (36) around the lower frame tubes and through each set of slotted holes in the lower plate of the vehicle mounting frame (total of four “U” bolts). Fasten loosely using 5/16″ flat washers (41), 5/16″ lock washers (40), and 5/16″-18 nuts (42). 2.4 Tighten all the fasteners holding the vehicle mounting frame to the vehicle starting with the 6mm. bolts

Incoming search terms:

2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

Removal and Fitting of Tyres

0

Filed Under (Tips and Review) by admin on 17-11-2010

download
General Advice Tyres are the only parts of the motorcycle which are in contact with the road. Safety in acceleration, braking, steering and cornering all depend on a relatively small area of road contact. It is therefore of paramount importance that tyres should be maintained in good condition at all times and that when the time comes to change them suitable replacements are fitted. The original tyres for a motorcycle are determined by joint consultation between the motorcycle and tyre manufacturers and take into account all aspects of operation. It is recommended that changes in tyre size or type (construction) should not be undertaken without seeking advice from the motorcycle or tyre manufacturers, as the effect on motorcycle handling, safety and clearances must be taken into account. The tyre industry has long recognised the consumer’s role in the regular care and maintenance of their tyres. The point at which a tyre is replaced is a decision for which the owner of

Incoming search terms:

Honda CG125 Owners Manual, and repair manual

0

Filed Under (Honda) by admin on 11-12-2011

download
The author of this manual has the conviction that the only way in which a meaningful and easy to follow text can be
written is first to do the work himself, under conditions similar to those found in the average household. As a result, the hands seen in the photographs are those of the author. Even the machines are not new: examples that have covered a consider- able mileage were selected so that the conditions encountered would be typical of those found by the average owner. Unless specially mentioned, and therefore considered essential, Honda service tools have not been used. There is
invariably some alternative means of slackening or removing some vital component when service tools are not available and
isk of damage has to be avoided at all costs. Each of the six Chapters is divided into numbered Sections. Within the Sections are numbered paragraphs. In consequence, cross reference throughout this manual is both straightforward
and logical. When a reference is made ‘See Section 5.12′ it means Section 5, paragraph 12 in the same Chapter. If another
Chapter were meant, the text would read ‘See Chapter 2, Section 5.12′. All photographs are captioned with a Section/paragraph number to which they refer and are always relevant to the Chapter text adjacent. Figure numbers (usually line illustrations) appear in numerical order, within a given Chapter. Fig. 1.1 therefore refers o the first figure in Chapter 1. Left-hand and right-hand descriptions of the machines and their component parts refer to the right and left of a given machine when the rider is seated normally. Motorcycle manufacturers continually make changes to specifications and recommendations, and these, when notified,mare incorporated into our manuals at the earliest opportunity.
We take great pride in the accuracy of information given in this manual, but motorcycle manufacturers make alterations and design changes during the production run of a particular n motorcycle of which they do not inform us. No liability can be ccepted by the authors or publishers for loss, damage or injury caused by any errors in, or omissions from, the information give

Incoming search terms:

Triumph SU CARBURETORS SERVICING AND TUNING

0

Filed Under (Triumph) by admin on 29-10-2010

download
Jets: These are made in various sizes ranging from.099 inches to.1875 inches, the larger sizes being used only for racing or very high performance engines. The two sizes most commonly found on production cars are the.090 inch and the.100 inch. The size of the jet will be found stamped on the jet head. The figure “nine”wilt indicate that it is the.090 inch and the figure “one”will indicate the.100 inch jet. When tuninga production car the jets size should be checked to make sure that it is of the size recommended by the manufacturers. Centering of Jet: If for any reason, the jet assembly has been removed, it will be ne cessary to recenter the jet. First, remove the clevis pin at the base of the jet which attaches the jet head to the jet operating lever. Withdraw the jet completely and remove the adjusting nut and spring, then replace the adjusting nut, without its spring, and screw it up toits highest position. Slide the Set into position until the jet head is against the base of the adjusting nut. When this has been done, find out if the piston is perfectly free by lifting it up with the finger and allowing it to drop. If the piston is not entirely free, slacken the jet screw and manipulate the lower part of the assembly, including the projecting part of the bottom half of the jet bearing, adjusting nut, and jet head. Make sure that this assembly is now slightly loose. The piston should then rise and fall quite freely as the needle is now able to move the jet into the required central position. The jet screw should now be tightened and a further check made to determine that the piston is still quite free. When complete freedom of the piston is achieved the jet adjusting nut should be removed, together with the jet, and the spring replaced. Experience has shown that a large percentage of carburetors, which have given trouble has been due to the incorrect centering of jets. Jet Needles— These are made in a great variety of sizes, probably now well over two hundred and fifty, and each type of engine hasaneedlethat has been selected, after very careful tests have been carried out, to give the best all-round performance. Most manufacturers actually give three alternative needles for each type and size of engine, these needles clearly being listed by the manufacturer “Standard”, “Rich”or”Weak”and before tuning is started the needle, which is marked on the shank should be checked against the manufacturer’srecommendation to make quite sure that the right needle is fitted; this is most important.

Incoming search terms:

Honda 300 2×4 Lift Kit Installation Instructions

0

Filed Under (Honda) by admin on 11-12-2011

download
This product is designed for us e on ATVs on which additional ground clearance and fender clearance is desired. It is designed for utility type, slower-speed use on relatively flat terrain in deep mud or snow. Although we have many thousands of satisfied lift kit customers and over 400 franchised dealers selling and installing lift kits, purchasers should be aware that use of this product may increase the frequency of required maintenance, part wear, and will raise the center of gravity on your ATV increasing risk of roll-over on side hills, ditches or other steep terrain. We recommend that wider tires and/or wheel spacers be used to achieve a wider stance and to improve stability of the ATV. Riders should be advised that the handling characteristics of a taller ATV are different and require extra care when riding on side hills or off-camber situations. If you further raise the center of gravity by adding heavy loads to racks or seats, the ATV must be operated with care, at slower speeds or on relatively flat ground. Operation of an ATV with or without a lift kit, while or shortly after consuming alcohol or drugs, subjects the rider to the risk of serious bodily harm or possible death. This is compounded if the rider does not wear an approved helmet and other safety gear. High Lifter urges that all approved safety gear be worn when riding an ATV. If this is not what you expected, or is not consistent with your intended use, you should return the product immediately to the seller, before installation, for a refund of the purchase price; less any fees. After installation, product is warranted for 90 days for defects in workmanship and materials. Warranty is limited to refund of the purchase price or replacement of the kit, at the seller’s option.

Integral ABS and ASC – new Riding Dynamic Control Systems for BMW Motorcycles

0

Filed Under (BMW) by admin on 16-11-2010

download
Entering its next generation, BMW Motorrad Integral ABS is taking a quantum leap in the process of evolution, advancing from a stand-alone solution acting only on the brakes into a fully networked all-round system. Offering the new generation of Integral ABS, BMW Motorrad provides the foundation for additional dynamic riding control systems with a reduction in technical requirements and features. And following the customer’s wishes, this new generation also opens up the option in future for further-reaching rider assistance functions. The first step in this direction is BMW Motorrad ASC Automatic Stability Control available as of 2007. This system serving to control drive spin on a production motorcycles is being introduced as an optional extra on the touring models in the BMW K and Boxer Series. Once again, therefore, BMW is acting as the pioneer in the introduction of advanced safety technologies on the motorcycle. This further enhances the leadership which BMW Motorrad has shown in the area of active safety for more than 15 years. Choosing the right development partner for both systems, BMW Motorrad obviously had to focus on that partner’s specific competence in control technology and the networking of functions within the vehicle. In recent years, major car suppliers have become aware of the technical challenges presented by the motorcycle with its specific riding dynamics and the growing potential for motorcycle control systems in the market. The decisive point in preselection of the development partner was the willingness and ability to develop specialised solutions suitable for use on BMW motorcycles. So taking this into account, joint development of the new generation of ABS brake technology started together with Continental-Teves in early 2003. Integral ABS. BMW Motorrad’s new Integral ABS technology has been developed separately from the previous system and the entire layout of the system has been newly conceived from the ground up. Capitalising on progress in technology in both hydraulics and electronics, the development engineers have succeeded in simplifying the architecture of the system while at the same time enhancing its functions to an even higher standard. The result is supreme stopping power and very short stopping distances even without electrical power assistance on the brakes.

1999-2002 SUZUKI SV 650 OWNER'S MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FUEL, ENGINE OIL AND COOLANT RECOMMENDATION FUEL Your motorcycle requires regular unleaded gasoline with a minimum pump octane rating of 87 ((R+M)/2 method) . In some areas,the only fuels that are available are oxygenated fuels. Oxygenated fuels which meet the minimum octane requirement and the requirements described below may be used in your motorcycle without jeopardizing the New Vehicle Limited Warranty or the Emission Control System War- ranty. NOTE: Oxygenated fuels are fuels which contain oxygen-carrying additives such as MTBE or alcohol. Gasoline Containing MTBE Unleaded gasoline containing MTBE (Methyl Tertiary Butyl Ether) may be used in your motorcycle if the MTBE content is not greater than 15%. This oxygenated fuel does not contain alcohol. Gasoline/Ethanol Blends Blends of unleaded gasoline and ethanol (grain alcohol), also known as GASOHOL, may be used in your vehicle if the ethanol content is not greater than 10%. Gasoline/Methanol Blends Fuels containing 5% or less methanol (wood alcohol) may be suitable for use in your motorcycle if they contain co-solvents and corrosion inhibitors. DO NOT USE fuels containing more than 5% methanol under any circumstances. Fuel system damage or motorcycle performance problems resulting from the use of such fuels are not the responsibility of Suzuki and may not be covered under the New Vehicle Limited Warranty or the Emission Control System Warranty . Fuel Pump Labeling In some states, pumps that dispense oxygenated fuels are required to be labeled for the type and percentage of oxygenate, and whether important additives are present . Such labels may provide enough information for you to determine if a particular blend of fuel meets the requirements listed above. In other states, pumps may not be clearly labeled as to the content or type of oxygenate and ad- ditives . If you are not sure that the fuel you intend to use meets these requirements, check with the service station operator or the fuel suppliers

Incoming search terms:

1999-2002 SUZUKI SV650 OWNER'S MANUAL

0

Filed Under (Suzuki) by admin on 12-12-2010

download
Gasoline/Ethanol Blends Blends of unleaded gasoline and ethanol (grain alcohol), also known as GASOHOL, may be used in your vehicle if the ethanol content is not greater than 10%. Gasoline/Methanol Blends Fuels containing 5% or less methanol (wood alcohol) may be suitable for use in your motorcycle if they contain co-solvents and corrosion inhibitors. DO NOT USE fuels containing more than 5% methanol under any circumstances. Fuel system damage or motorcycle performance problems resulting from the use of such fuels are not the responsibility of Suzuki and may not be covered under the New Vehicle Limited Warranty or the Emission Control System Warranty . Fuel Pump Labeling In some states, pumps that dispense oxygenated fuels are required to be labeled for the type and percentage of oxygenate, and whether important additives are present . Such labels may provide enough information for you to determine if a particular blend of fuel meets the requirements listed above. In other states, pumps may not be clearly labeled as to the content or type of oxygenate and ad- ditives . If you are not sure that the fuel you intend to use meets these requirements, check with the service station operator or the fuel suppliers. d of. ; NOTE: • * To help clean the air, Suzuki recommends that you use the oxygenated fuels . • * Be sure that any oxygenated fuel you use has octane ratings of at least 87 pump octane ((R+M)/2 method) . • * If you are not satisfied with the driveablity or fuel economy of your motorcycle when you are using an oxygenated fuel, you should switch back to regular unleaded gasoline . • * If engine pinging is experienced, substitute another brand as there are differences between brands . A CAUTION Spilled gasoline containing alcohol can harm your motorcycle. Alcohol can damage painted surfaces. Be careful not to spill any fluid when filling the fue

Kawasaki VN1600 Highway Bar INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
PREPARATION 1. Insure that the motorcycle is on flat level ground. 2. It is recommended that the motorcycle sit for at least one hour prior to installation to allow the engine to cool. During installation tight all fasteners to hold. Wait until you check all clearances and operation of the brake and shift lever to firmly tighten and torque all fasteners. INSTALLATION Right Side Highway Bar 1. Remove the front floor board bolt (M10). (14mm Socket) Figure 1. Right and Left side of Motorcycle is determined while sitting on the bike.
MAINTENANCE / CAUTION The high quality chrome finish of your National Cycle Chrome Highway Bar can be maintained with any quality chrome cleaner and / or polish applied with a soft cloth. Check hardware for tightness regularly. Never ride with loose mounting hardware. Check to be sure your Highway Bar does not contact any part of the motorcycle at a full turn left and right. Correct any problem before using the motorcycle. ©2005 National Cycle, Inc. PO Box 158, Maywood, IL60153-0158 USA 708-343-0400 / Fax: 708-343-0625 / www.nationalcycle.com / e mail: info@nationalcycle.com Page 2 of 2 10-114857-000 09/05 Install Upper “U” Bolt 2. Place “U” Bolt between the radiator and the down tube at the location shown in Figure 2. Threaded ends of “U” will face out- ward. 3. Select the right side Highway Bar. 4. Loosely install the Highway Bar at the lower mount point using the stock screw. (14mm Socket) Figure 3. While installing the Whizlock Nuts in the following Step #5 , be certain to tighten the nuts evenly, alternating left and right as you tighten. When complete you want the same amount of threads exposed on the ends of the “U” to insure the bolt does not rotate. 5. Install the upper Highway Bar with Whizlock Nuts. (1/2″ Socket) Figure 4. Orient assembly so Whizlock Nuts face outside. Firmly tighten after all clearances are checked. LEFT SIDE INSTALLATION 6. Repeat Steps 1 and 2. On the Left Side due to tight clearances between the radiator and the down tube you must locate the point where the radiator is “notched out” slightly. Figure 5. 7. Select the left side Highway Bar. 8. Repeat Steps 4 and 5.

Incoming search terms: