mferemoval100 exe download

You search Auto repair manual PDF mferemoval100 exe download, if there are search results will appear below. If search results do not exist, please search by others keyword.



  mferemoval100 exe download Direct Download speed 5282 Kb/s

  mferemoval100 exe download Full Version speed 6162 Kb/s



Harley Davidson Softails Shocks Installation download

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
Progressive Suspension shocks for your Softail are designed as a direct bolt on replacement for your stockers. Although they are very similar in appearance, they have vastly improved damping and spring rates. Our shocks do not use the remote reservoir system used on earlier model Softail models. 1. Place motorcycle securely on stand or blocks so the rear wheel is slightly off the ground. 2. Per instructions in a authorized shop manual, remove your old shocks. Note location of the mounting hardware. 3. Install the Progressive Suspension shocks using the stock mounting bolts and washers. 4. Tighten all shock mounting bolts to the proper torque specifications (see shop manual for specs) 5. Progressive Suspension shocks have adjustable pre-load to compensate for varying weights. The included wrench or a Harley Davidson pre-load adjustment wrench is necessary to adjust the pre-load setting. Replacement Progressive Suspension, Inc. wrenches are available as Part # SW-784 from most Dealers and Accessory Stores and the Harley Davidson wrench is available as part #94455-89 from any Harley Davidson Dealer. Spring preload is set by us to the lightest setting. To increase preload for heavier riders/loads/passengers, loosen locknut with the inside portion of the supplied wrench or a 1 1/ 16 ” wrench and back it off several turns. Use the supplied wrench or a Harley adjustment wrench to turn the adjustment nut counterclockwise to the desired preload setting. Then tighten the 11/ 16 ” lock nut. Both shocks must be adjusted to the same, equal setting

Incoming search terms:

2003-2007 Victory Motorcycles Installation Instructions for S&S Freedom Performance Tuner

0

Filed Under (Victory) by admin on 31-10-2010

download
Once the download of S&S Freedom Performance Tuner has been installed on your PC, double click the icon on your desk top. Picture 3 illustrates the S&S Freedom Performance Tuner icon. 2- Enter in your Username and Password and click the login button. Your Username and Password for logging in will be the same as your login for Picture 1 Picture 2 Picture 3 3 3 – Once you’re logged onto S&S® Freedom® Performance Tuner, click on the Year and Model of the bike you’re performing the work on in the middle of the page as illustrated in Picture 4. 4 – Click on the Select Vehicle tab at the bottom of the page as illustrated in Picture 5. The tabs on the left side of the page will now be illuminated. Picture 4 Picture 5 4 5- Click on the ECU Reprogramming tab on the left side of the screen as illustrated in Picture 6. 6- In the center of the screen you will now be prompted to enter in customer information, VIN number of the motorcycle you are performing calibration download on, and calibration card number. Select a re-flash file from the drop down list that you want to download into the motorcycle. All the fields must be filled out for you to continue with the download. Picture 7 illustrates the information screen with required fields filled out. Picture 6 Picture 7 5 Note: Due to the limited description space available in the drop down list in S&S® Freedom® Performance Tuner, a detailed list of available calibrations and part numbers can be viewed on the S&S dealer web. Go to ® Calibrations on the left side of the home page. Here you will find a detailed list of calibrations and part numbers for reference only. Picture 8 illustrates the home page and location for the S&S/Victory Calibrations. Picture 9 illustrates the calibrations for reference

Incoming search terms:

FC designed and built solely for Victory Motorcycles Installation

0

Filed Under (Victory) by admin on 31-10-2010

download
1. Remove gas tank as per service manual procedure 2. Disconnect negative lead from battery 3. Determine a location for the VFC III unit. Suggested locations are as follows: on left or right side under the covers, on top or side of battery, on inside of the side covers, on PCM or under seat 4. Locate rear injector, disconnect factory connection using care not to break it, the red tab must be lifted first and then push the release to remove plug. Plug it into the female end of the VFC, Then plug the male end of the VFC into the injector. 5. Locate connection of front jumper harness- it is located on the right side of frame – in the center of air box. Disconnect and plug appropriate VFC connectors in place. 6. Zip tie harness so that it is free from being contacted 7. Install gas tank and connect ground terminal of VFC along with the factory ground lead. Note, On Vegas, Kingpin, Jackpot & Hammer Models. Be sure not to pinch VFC harness under rear tank mounting bracket, the harness must run on the side of or under the frame in this area as not to contact the rear tank mount. 8. Turn the motorcycle key to the “ON” position, after fuel pump cycles the Green / Red lights will flash and will remain flashing until an injector signal is detected, this occurs when the M/C is started. Once running the green will scroll for 4 seconds and then turn solid until another circuit is activated. Some 2000-20001 bikes will not light the box until started. The module controls your basic fuel adjustments and your fuel delivery for the Nitrous when activated. The following functions and colors that represent them are as follows. Basic Module description and adjustments ; the module has 3 button adjustments, Center is the mode selector, this scrolls through and chooses the feature that you want to adjust. To the left of it is the button in which minus’s in value the selected feature. To the right of the mode button is the plus button which makes the feature selected go higher in value. If a fuel feature is selected the minus button will diminish fuel down to the lowest level of the current download and plus will add fuel up to the maximum amount calibrated into the module. There are 8 LED lights on the front panel with 15 points of adjustment ranging from 0 to 8 in increments of .5 or 1/2 . Ex. 1 – 1.5 – 2 – 2.5 – 3 – 3.5 – 4 – 4.5 – 5 – 5.5 – 6 – 6.5 – 7 – 7.5 – 8

Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

2002 Honda VFR 800 VTEC Power Commander 111-210 Installation Instructions

0

Filed Under (Honda) by admin on 26-11-2011

download
If you feel that you are having any problems at all with the Power Commander II, disconnect it from your motorcycle. This will allow the motorcycle to run directly off of the stock ECU. The lights don’t come on when I turn the ignition switch on.
Check to make sure connectors are seated and the kill switch is in the “run” position. The on-board adjustment buttons do not hold their settings. Be sure to wait 20-30 seconds after making adjustments before starting or turning off the bike.
Can not upload to or download from the Power Commander II. Check to see that the serial cable is firmly in place. Verify that ignition switch is on and the kill switch is in the “run” position. My mouse uses the same serial port. If your computer has a PS/2 port purchase a DB9 to PS/2 adapter for your mouse. I get a “verify failed….” message when I upload a map to the Power Commander II. Programs running in the background or fluctuations in supply voltage (from outlet) can sometimes cause this error. In most cases, the information was sent properly to the Power Commander II. Pushing
the “upload all” button again should produce a “tables sent and verified” message. I typed in notes, but they didn’t save.
You need to first push the “accept” button in the notes window and then the “save file” button.

Incoming search terms:

Yamaha TDM 900 Disconnecting the battery ground REMOVAL AND INSTALLATION

0

Filed Under (Yamaha) by admin on 29-01-2012

download
Remove the seat. • Disconnect the battery ground (negative terminal). Remove the fairing side panels. • Remove the four marked hex screws with plastic washers. Note the positions the screws come from as they are not all the same. • Note that the bottom, rear hex bolt has a retaining plastic washer INSIDE the fairing. The long bolt goes under the ‘twin’ label. • Remove the hex screw indicated on the inside of the fairing panel. • Remove the grey Phillip’s head screw as indicated on the inside panel. • Remove the plastic locking clip on the underside of the fairing behind the radiator.

Yamaha WR 250F and WR450F Dual Sport Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-01-2012

download
license Plate Mount Installation: Locate the aluminum license plate mount and license plate light assembly. Remove the rear most nut securing the stock taillight assembly (underneath the fender) (don’t lose the little compression tube and washer). Temporarily install the license plate mount to this location and mark the fender where it needs to be drilled for the rear mounts. Drill the fender in two places with a ¼” drill and reinstall the license plate assembly using the stock taillight mount and the 6 x 20 mm countersunk screws, bezels and nylock nuts Rear Turn Signal Installation: Locate the two rear turn signals in the kit – they’re the ones with the longer wires. Drill a 3/8 hole in each side of the fender as shown in Photo 3 and attach them as shown in Photo 4. It does no matter which signal goes on which side. Run the left turn signal wires forward along with the taillight wires, up through the grommet in the fender to the area just behind the air box cross member and above the fender. Run the right turn signal wires forward along the right frame rail, and through the same hole you made for the license plate wires Brake Light Switch Installation: The WR250/450 uses a hydraulic brake switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the rear brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the rear master cylinder guard. Remove the bolt holding the brake fluid reservoir to provide access to the master cylinder. Loosen the banjo bolt securing the rear brake line to the master cylinder. Typically, this bolt will be very tight and loosening it will bend the support hanger for the master cylinder if not supported. Brace the master cylinder with a wrench or lever. Remove the banjo bolt and replace with the hydraulic switch. Make sure to install the copper crush washer from the stock bolt under the switch. Torque the switch assembly to 25 lb-ft.

YAMAHA R1 OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 28-12-2011

download
The majority of fatalities from motorcycle accidents are the result of head injuries. The use of a safety helmet is the single most critical factor in the prevention or reduction of head injuries. Always wear an approved helmet. Wear a face shield or goggles. Wind in your unprotected eyes could contribute to an impairment of vision that could delay seeing a hazard. The use of a jacket, heavy boots, trousers, gloves, etc., is effective in preventing or reducing abrasions or lacerations. Never wear loose-fitting clothes, otherwise they could catch on the control levers, footrests, or wheels and cause injury or an accident. Never touch the engine or exhaust system during or after operation. They become very hot and can cause burns. Always wear protective clothing that covers your legs, ankles, and feet. A passenger should also observe the above precautions. Modifications Modifications made to this motorcycle not approved by Yamaha, or the removal of original equipment, may render the motorcycle unsafe for use and may cause severe personal injury. Modifications may also make your motorcycle illegal to use. Loading and accessories Adding accessories or cargo to your motorcycle can adversely affect stability and handling if the weight distribution of the motorcycle is changed. To avoid the possibility of an accident, use extreme caution when adding cargo or accessories to your motorcycle. Use extra care when riding a motorcycle that has added cargo or accessories. Here are some general guidelines to follow if loading cargo or adding accessories to your motorcycle

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

YAMAHA V-STAR 650 CA SHORTSHOTS STAGGERED INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
Check condition of stock exhaust gasket. Replace if damaged or worn. 2. Install mounting bracket (stamped 384-P) in the original bracket mounting position using two 8mm bolts (supplied)(Figure 1). Note: Install two 5/16″ x 5/8″ fl ange bolts (supplied)(Figure 1) into top holes of bracket before installing bracket onto motorcycle. 3. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside (Figure 2). Place each heat shield on a non abrasive surface such as a blanket or carpet. Lay each head pipe/muffl er onto its respective heat shield (Figure 3). 4. Loosely install each hose clamp by feeding tail end of clamp into heat shield clip (Figure 2). #20 hose clamps are for head pipes and #28 hose clamps for muffl er area. Take note of clamp screw head direction (Figure 4). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Note: Do not tighten yet. 5. Install 6″ fl ange bolts (supplied) engaging nut plate. Leave T-bolt clamp onto front muffl er (Figure 4&5). Slide muffl er onto front head pipe. Slide nut plate (supplied) inside bracket welded to backside of front muffl er (Figure 6). Attach muffl er to mounting bracket 384-P using two 5/1head pipe/muffl er assembly loose at this time. 6. Using stock Allen bolts, carefully install rear head pipe/ muffl er assembly into exhaust port. (Assistance may be required). Note: Do not tighten yet. 7. Slide nut plate (supplied) inside bracket welded to backside of rear muffl er (Figure 6). 8. Align muffl ers so they are parallel when viewed from the right side of the motorcycle and muffl er tips align at the same length. Tighten 5/16″ fl ange bolts securing muffl ers to bracket. 9. Tighten cylinder exhaust port bolts securing head pipes to cylinder head. 10. Tighten T-bolt clamp securing front muffl er to head pipe. 11. Adjust heat shields so that muffl er tips protrude 1/4″ from heat shields (Figure 7) and rotation of heat shield matches muffl er tip. Tighten all hose clamps securing heat shields. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. Note: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up. 13. All hardware must be properly tightened before starting motorcycle

Incoming search terms: