mikuni carburature for raider 150

You search Auto repair manual PDF mikuni carburature for raider 150, if there are search results will appear below. If search results do not exist, please search by others keyword.



  mikuni carburature for raider 150 Direct Download speed 5282 Kb/s

  mikuni carburature for raider 150 Full Version speed 6162 Kb/s



HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

Incoming search terms:

Dazon Raider Classic 150 (Oil-cooled & Internal Gearbox): Service Manual (single/ double-seat)

0

Filed Under (Dazon) by admin on 30-11-2010

download
1.2.1 Fuel Please use the gasoline of SAE 90# or above. Also we recommend you to use the unleaded gasoline. 1.2.2 Engine Oil Please use the high-quality engine oil of SAE 10w/30SF. 1.3 Break-in Procedure For your first 2 hours of riding, don’t exceed 2/3 throttles. Vary the engine speed for the first 5 hours. Never hold the engine at full throttle for long periods of time. Raider-Classic 150 (Oil-cooled&Internal Gearbox): Service Manual (single/ double-seat) EEC Version;3.0 Feb..2005 5 1.4 Specifications DIMENSIONS SINGLE-SEAT / DOUBLE-SEAT Overall Length 2330mm / 2300mm Overall Width 1310mm / 1460mm Overall Height 1425mm / 1425mm Wheelbase 1475mm / 1520mm Ground Clearance 200mm VIN Accord with GMVR A01-01 Statutory Plate& Safety Labels Accord with GB 7258-1997 ENGINE Model DZ1P57QMJ Type Oil-cooled, single cylinder, 4-Stroke Engine Capacity 150cc Displacement 149.6ml Bore X Stroke 57.4mm X 57.8mm Max Power 7.0kw or 7000r/m Max Torque 10.0N.m or 6500 r/m Idle Speed 1700 ± 100 r/m CO Emission 7.0g/km HC Emission 1.0g/km Fuel Type SAE 90# or above (unleaded) Lubricate Oil Type SAE 10W/30SF Lubrication Force & Splash Cooling Oil-cooled Ignition C. D. I. Starting Electric Spark Plug C7HSA (NGK) Spark Plug Gap 0.6~0.7mm Transmission Chain Transmission Gearbox Transmission Ratio F.:7.8:1 ; B.:11.297:1 Compression Ratio 9.5 ± 0.1 : 1 Carburetor MIKUNI BS 24-1005 Absorber Normal (in 10 5 times of experiments) CAPACITIES Front/ Rear Tire Load Coefficient 36 Front/ Rear Tire Speed Level L Fuel Tank 7.0L, 130kpa (no leakage in experiments) Engine Oil 1000ml Gear Oil 200ml Starting Time ≤15s Climbing ≥20%

Incoming search terms:

HSR Carburetor Total Kits Installation And Tuning Manual

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
1. Disconnect the battery ground wire from the battery. 2. Turn the fuel petcock to the “OFF” position. 3. Elevate the rear of the fuel tank for better access to the carburetor area. 4. Remove the coil, horn or other devices on the left hand side of the engine to allow free access to the intake manifold bolts. 5. Remove the complete air cleaner assembly, including the backing plate. 6. Disconnect any vacuum hoses and the fuel hose from the stock carburetor. 7. Disconnect the choke cable from the frame. 8. Remove the stock carburetor. 9. Evo: remove the stock manifold. 10. Twin Cam: unplug MAP sensor, remove manifold and then remove the MAP sensor from the manifold. Installation: Intake Manifold: Twin Cam only: Install MAP sensor in Mikuni manifold. 1. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 2. Attach the rubber flange to the Mikuni manifold with the 5/16″x3/4″ bolts and washers. To ease installation, use liqiud detergent to lubricate the manifold seals. Choke: Evo: We recommend that you use the Mikuni choke cable that is furnished with the carburetor. However, you can use the stock Harley cable (’90-’99 models only) if you follow the Twin Cam choke cable instructions. Twin Cam: 1. Remove the Harley choke cable from the stock carb. 2. Remove the Harley spring and plunger from the Harley choke cable. 3. Remove the Mikuni spring and plunger from the Mikuni carburetor. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut. 6. Install the new assembly into the Mikuni. Be careful to only gently tighten the plastic nut.

42MM MIKUNI FLATSLIDE CARBURETOR INSTRUCTIONS

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at 1/2 to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle. The output of the OEM fuel pump is too high and will cause fuel overflow in the HSR carb, resulting in a possible dangerous fire hazard

Incoming search terms:

Mikuni HSR 42/ 45 Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at ½ to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle.

Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

HOVELHEAD & IRONHEADXL 42mm Mikuni Carburetor And Manifold Kit INSTALLATION Instructions

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
THROTTLE CABLE ADJUSTMENT A) Rotate the throttle grip to the full open position, look into the throttle bore and see if the throttle valve (slide) opens completely. If the throttle valve does not open completely unscrew the adjuster on the opening cable until it does. This adjustment should be made carefully to assure maximum carburetor performance. After adjustment tighten the adjuster jam nut. B) After adjusting the open cable, adjust throttle freeplay with the closing (idle) cable to approximately 1/8″ an indicated in the following illustration. note It is very important to adjust the cables in the preceding described manner to ensure that the idle cable operates correctly for safety. It must close the throttle completely 2 PLEASE NOTE USE CAUTION PLEASE NOTE SAFETY WARNING pull open cable pull close cable SHOVELHEAD/IRONHEAD XL Installation Instructions Check and make sure that the throttle cables are routed properly by rechecking the throttle play as the handlebars are turned from side-to-side; the amount play should remain consistent. C) After the throttle cables have been adjusted, make sure that all the lock nuts are securely tightened. 5. AIR CLEANER A) The air filter bracket is attached to the crankcase with 1 long bolt, and a bracket-spacer. Removed the crankcase nut located between the tappet blocks & replace it with the enclosed bracket spacer; tighten the spacer securely. B) Remove the stud protectors from the K&N filter and place the two backing plates on the studs. Now slip the the filter onto the carburetor. C) Attach the 2 long brackets to the air filter studs with the enclosed nuts & flat washers, and to the bracket spacer with the enclosed bolt using the lock washers, and flat washers. When the carburetor and air cleaner are properly aligned, securely tighten all of the mounting hardware including the intake manifold clamps. In some cases it may be necessary to bend the brackets slightly to arrive at the correct fit. D) Use the enclosed hose clamps to secure the fuel hose to the petcock, and the HSR carburetor. The screw clamp goes on the petcock end and the spring clamp attaches to the carburetor end. E) Attach the chrome air filter cover with the enclosed socket head screw. 7. CHOKE CABLE INSTALLATION A) Attach the Mikuni choke cable bracket to the original choke cable bracket on the air cleaner stud with the enclose hardware as illustrated

MIKUNI VM CARBURETOR SUPER TUNING

0

Filed Under (Mikuni) by admin on 31-10-2010

download
This manual is intended as a guide for users of Mikuni carburetors who want to learn the adjusting method to the best performance from our products. In motorcycles, special tuning of the engine is now considereda routine practice. The arrows that appear in the drawings in this text show the direction in which air, fuel and an air-fuel mixture flows, respectively. ¢JAir Fuel “Mixture Mounting angle fore and aft inclination of the carb should not exceed approx Function of a carburetor The function of a carburetor is to produce combustible air-fuel mixture, by breaking fuel into tiny particles (in the form of vapor) and by mixing the fuel with air in a proper ratio, and to deliver the mixture to the engine. A proper ratio (mixture ratio or air-fuel ratio) means an ideal air-fuel mixture that can burn without leaving an excess of fuel or air, Whether the proper mixture ratio is maintained or not holds the key to the efficient engine operation, 2. Air-fuel mixture required by the engine (Fig. 1) The ratio of a mixture of fuel and air is called the mixture ratio or the air-fuel ratio and is generally expressed by the weight proportion. Theoretically, the amount of air required for complete combustion of 1 gram of fuel under normal conditions is

Incoming search terms:

KINROAD 150 SERVICE MANUAL

0

Filed Under (Kinroad) by admin on 27-11-2010

download
FUEL AND OIL RECOMMENDATIONS Be sure to use the specified fuel and oil. FUEL Gasoline should SAE 90# or higher. Unleaded gasoline is recommended. ENGINE OIL SAE10W-30 engine oil of high quality should be used. BREAK-IN PROCEDURE For the first 2 hours of riding, do not exceed 2/3 throttle. Vary engine speed for the first 5 hours. Never hold engine at full throttle for long periods of time. SPECIFICATIONS DIMENSIONS DOUBLE SEAT/SINGLE SEAT Overall Length 2159mm/2075mm Overall Width 1400mm/1235mm Overall Height 1470mm/1400mm Wheelbase 1499mm/1450mm Ground Clearance 170mm/130mm ENGINE Type Forced air-cooled, single cylinder, 4-Stroke Engine Capacity 150cc Displacement 149.5cc Bore x Stroke 57.4mm x 57.8mm Compression Ratio 9.2:1 Max Power 7.4kw/7500rpm Max Torque 9.5N.m/5500rpm Fuel Type SAE 90# or above (unleaded) Lubricate Oil SAE 10W/30 Ignition C.D.I. Starting Electric Spark Plug C7HSA (NGK) Transmission Automatic C. V. T. Carburetor MIKUNI, BS24J Lubrication Force & Splash

2011 FORD HARLEY-DAVIDSON F-150 TECHNICAL SPECIFICATIONS

0

Filed Under (Harley Davidson) by admin on 01-11-2010

download
Final assembly location Dearborn Truck Plant, Dearborn, Mich. POWERTRAIN AND CHASSIS ENGINE Type 6.2-liter two-valve V8 Configuration Iron block, aluminum heads Valvetrain SOHC, two valves per cylinder, roller-rocker shaft with hydraulic lash adjusters Bore x stroke 4.02 x 3.74 inches Displacement 379 cubic inches, 6,210 cc Compression ratio 9.8:1 Horsepower 411 hp @ 5,500 rpm Torque 434 lb.-ft. @ 4,500 rpm Fuel Injection Sequential multi-port electronic Oil capacity Seven quarts DRIVETRAIN Layout RWD or AWD TRANSMISSION Standard Six-speed automatic overdrive Gear ratios 1st 4.17:1 2nd 2.34:1 3rd 1.52:1 4th 1.14:1 5th 0.86:1 6th 0.69:1 Reverse 3.40:1 Available axle ratios 3.73 SUSPENSION Front 4×2 Coil-on-shock, long-spindle double-wishbone independent, stamped-steel lower control arm (sport-tuned) Front 4×4 Coil-on-shock, long-spindle double-wishbone independent, stamped-steel lower control arm (sport-tuned) Rear 4×2 Hotchkiss-type non-independent live, leaf springs and outboard shock absorbers (sport-tuned) Rear 4×4 Hotchkiss-type non-independent live, leaf springs and outboard shock absorbers (sport-tuned) STEERING Type Power rack-and-pinion Turning circle curb-to-curb 47.0 feet 2011 FORD HARLEY-DAVIDSON F-150 TECHNICAL SPECIFICATIONS BRAKES Front 13.8-inch vented disc Rear 13.7-inch vented disc Assist type Vacuum, RSC WHEELS AND TIRES Wheels 22-inch polished forged aluminum with painted accents with “Harley- Davidson” Bar & Shield logo on wheel ornament Tires P275/45R-22 all-season BSW DIMENSIONS (inches unless otherwise noted) EXTERIOR SuperCrew RWD SuperCrew AWD Wheelbase 144.5 144.5 Vehicle length 231.9 231.9 Vehicle width (without mirrors) 79.2 79.2 Vehicle height 74.8 75.9 Track width, front/rear 67.0/67.0 67.0/67.0 Cargo box length 67.0 67.0 Width (max) between wheels 50.0 50.0 Inside box height 22.4 22.4 INTERIOR Seating capacity Five Five Headroom Front row 41.0 41.0 Rear row 40.3 40.3 Legroom Front row 41.4 41.4 Second row 43.5 43.5 Shoulder room Front row 65.9 65.9 Second row 65.5 65.5 Hip room Front row 60.5 60.5 Second row 64.6 64.6 WEIGHTS AND TOWING (pounds)

Incoming search terms:

Incoming search terms: