mikuni carburetor vacuum slide

You search Auto repair manual PDF mikuni carburetor vacuum slide, if there are search results will appear below. If search results do not exist, please search by others keyword.



  mikuni carburetor vacuum slide Direct Download speed 5282 Kb/s

  mikuni carburetor vacuum slide Full Version speed 6162 Kb/s



HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

HSR Carburetor Total Kits Installation And Tuning Manual

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
1. Disconnect the battery ground wire from the battery. 2. Turn the fuel petcock to the “OFF” position. 3. Elevate the rear of the fuel tank for better access to the carburetor area. 4. Remove the coil, horn or other devices on the left hand side of the engine to allow free access to the intake manifold bolts. 5. Remove the complete air cleaner assembly, including the backing plate. 6. Disconnect any vacuum hoses and the fuel hose from the stock carburetor. 7. Disconnect the choke cable from the frame. 8. Remove the stock carburetor. 9. Evo: remove the stock manifold. 10. Twin Cam: unplug MAP sensor, remove manifold and then remove the MAP sensor from the manifold. Installation: Intake Manifold: Twin Cam only: Install MAP sensor in Mikuni manifold. 1. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 2. Attach the rubber flange to the Mikuni manifold with the 5/16″x3/4″ bolts and washers. To ease installation, use liqiud detergent to lubricate the manifold seals. Choke: Evo: We recommend that you use the Mikuni choke cable that is furnished with the carburetor. However, you can use the stock Harley cable (’90-’99 models only) if you follow the Twin Cam choke cable instructions. Twin Cam: 1. Remove the Harley choke cable from the stock carb. 2. Remove the Harley spring and plunger from the Harley choke cable. 3. Remove the Mikuni spring and plunger from the Mikuni carburetor. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut. 6. Install the new assembly into the Mikuni. Be careful to only gently tighten the plastic nut.

HOVELHEAD & IRONHEADXL 42mm Mikuni Carburetor And Manifold Kit INSTALLATION Instructions

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
THROTTLE CABLE ADJUSTMENT A) Rotate the throttle grip to the full open position, look into the throttle bore and see if the throttle valve (slide) opens completely. If the throttle valve does not open completely unscrew the adjuster on the opening cable until it does. This adjustment should be made carefully to assure maximum carburetor performance. After adjustment tighten the adjuster jam nut. B) After adjusting the open cable, adjust throttle freeplay with the closing (idle) cable to approximately 1/8″ an indicated in the following illustration. note It is very important to adjust the cables in the preceding described manner to ensure that the idle cable operates correctly for safety. It must close the throttle completely 2 PLEASE NOTE USE CAUTION PLEASE NOTE SAFETY WARNING pull open cable pull close cable SHOVELHEAD/IRONHEAD XL Installation Instructions Check and make sure that the throttle cables are routed properly by rechecking the throttle play as the handlebars are turned from side-to-side; the amount play should remain consistent. C) After the throttle cables have been adjusted, make sure that all the lock nuts are securely tightened. 5. AIR CLEANER A) The air filter bracket is attached to the crankcase with 1 long bolt, and a bracket-spacer. Removed the crankcase nut located between the tappet blocks & replace it with the enclosed bracket spacer; tighten the spacer securely. B) Remove the stud protectors from the K&N filter and place the two backing plates on the studs. Now slip the the filter onto the carburetor. C) Attach the 2 long brackets to the air filter studs with the enclosed nuts & flat washers, and to the bracket spacer with the enclosed bolt using the lock washers, and flat washers. When the carburetor and air cleaner are properly aligned, securely tighten all of the mounting hardware including the intake manifold clamps. In some cases it may be necessary to bend the brackets slightly to arrive at the correct fit. D) Use the enclosed hose clamps to secure the fuel hose to the petcock, and the HSR carburetor. The screw clamp goes on the petcock end and the spring clamp attaches to the carburetor end. E) Attach the chrome air filter cover with the enclosed socket head screw. 7. CHOKE CABLE INSTALLATION A) Attach the Mikuni choke cable bracket to the original choke cable bracket on the air cleaner stud with the enclose hardware as illustrated

Mikuni VM 36 mm Round Slide Carburetor Instalation

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Carbs fit perfectly in the stock carb mounting boots for 1980 and up XS 650s that came with the chrome *bit of tin” vacuum chamber tops. Air filters extend to stock battery box.The custom 2 into 1 throttle cable comes made to fit with the stock Yamaha throttle housing! This bike idles crisp and clean, has instant throttle response and pulls hard from idle to redline, no bog, or loading up, even with the bone stock exhaust system. Very impressive performance over the stock worn out 34mm CV carbs

Adjusting the Pekar K68 for Dnepr or Ural

0

Filed Under (Tips and Review) by admin on 11-11-2010

download
1. Make sure the ignition timing is correct 2. Adjust the valves as necessary to ensure proper operation 3. Run the engine to warm it up a bit 4. Adjust the float setting. To do this, remove the carburetors (leave the throttle cables attached), remove the bowl and turn the carburetor upside down (fuel will spill). The float should look like this: Adjust as necessary by bending the float support (#37 in Figure 1). Reinstall Installation and idle adjustment 1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns. * Starting using the K68′s (cold weather) 1. Verify fuel flow. Apply choke (pull 52 in Fig1). 2. Using the ticklers (13) allow fuel to enter the bowl until fuel drains from (14) 3. With the ignition off, kick 1 or 2 times 4. Turn ignition on, and as soon as engine is warmed up (maybe sooner) push choke mechanisms to open choke Idle Adjustment (engine running and warm) 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ΒΌ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Related Item : how adjust a carburator for 2003 honda xr50r (2)yz 250f ignition tune (1)kymco zx-50 carburetor adjustment (1)ke-100 troubleshooting carb problems (1)how to set valves on motomia 125cc (1)how to set valves on 2006 honda crf150f (1)how to set round float on harley keihin cv carb (1)how to dismantle carburator of 2011 honda baja 150cc (1)how to check timing on 1 cyl dune buggy (1)How to adjust handlebars on a 2008 Yamaha F JR 1300 (1)