moto guzzi v7 service schedule

You search Auto repair manual PDF moto guzzi v7 service schedule, if there are search results will appear below. If search results do not exist, please search by others keyword.



  moto guzzi v7 service schedule Direct Download speed 5282 Kb/s

  moto guzzi v7 service schedule Full Version speed 6162 Kb/s



1991 MAINTENANCE SCHEDULE FOR MR2, PREVIA & LAND CRUISER

0

Filed Under (Toyota Manuals) by admin on 27-10-2011

download
For 1991 models, the Toyota owner’s manual offers 3 maintenance sections within the maintenance chapter following the introduction page as follows: (1) GENERAL MAINTENANCE This section describes maintenance items which are the owner’s responsibility. (2) SCHEDULE A This schedule is for those Toyota vehicles which may require more frequent maintenance, due to driving conditions, environment, etc. This was formerly known as the “Severe” schedule. (3) SCHEDULE B This schedule is Toyota’s minimum maintenance requirement. Items on this schedule must be performed to maintain Toyota’s warranty coverage. This was formerly known as the “Normal” schedule. The highlights of required service are as follows: – Every 7,500 or 12 months / oil and filter change – Every 15,000 or 24 months / chassis components service – Every 30,000 or 36 months / engine and chassis service A summary of the 1991 maintenance schedule “B” chart for three 1991 Toyota models is provided on page 3 of this bulletin for your convenience and quick referenc

Incoming search terms:

SUZUKI GSX-R1000 SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 12-11-2010

download
Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. 5. Install the air cleaner box in reverse order of removal. (Refer to Service Manual, Page 5-14) 6. Lower the fuel tank. (Refer to Service Manual, Page 5-3) 7. Remove the upper seat rail plate. Disconnect and remove the ECM. (Figure 1) @ ISC Valve Mounting Screw Torque: 2.1± ±0.6 N.m (1.5± ±0.4 lb-ft) ! Carefully insert the ISC valve straight into the throttle body hole to prevent damaging the o-ring. Turn the ISC valve slightly to confirm that the o-ring has not twisted. Using the new screw provided in the replacement parts kit, make sure the screw is completely seated on the plate after the screw has been tightened to the specified torque. 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. ! Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) REPLACEMENT PROCEDURE: 8. Install the new ECM in reverse order of removal. Apply thread lock to the upper plate mounting bolts when reinstalling the upper seat rail plate.

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

Moto Guzzi Sport 1100i Owners Manual

0

Filed Under (Moto Guzzi) by admin on 29-11-2010

download
General features Identification data Instruments and controls Riding your motorcycle Break-in Maintenance and adjustments Wheel removal Service schedule Cleaning – Storing Cleaning the windscreen Lubrication Valve gear WEBER injectionignition system (I.A.W.) Electrical equipment Wiring diagram Illustrations Lubrication Pressure fed by gear pump. Oil filters: wire mesh inside sump and replaceable cartridge filter outside sump. Normal lubrication pressure 3.8Ö 4.2 [5] kg/cm2, pressure valve, thermostat and cooler. Low oil pressure sensor (electrical) on crankcase. Generator/Alternator On front of crankshaft (1 4V – 25A). Ignition “WEBER MARELLI” electronic digital induced discharge, with high efficiency coil. Spark plugs: Spark plug gap: 0,7 mm. SPORT 1100 DAYTONA R NGK BPR 6 ESI NGK DR9 E IMS Starting Electric starter (12V-1,2 kW) with solenoid engagement. Ring gear bolted on flywheel. Starter button (START) on right of handlebars. Driveline data Clutch Twin driven plates, dry type, on flywheel. Hand controlled by lever on left of handlebars. Primary drive By gears. Ratio: 1 to 1.3529 (tooth ratio 17/23). Gearbox 5-speed, with constantly meshed gears with front dog clutch. Incorporated cush drive. Pedal operated on the left side of the motorcycle. Gear ratios: Low gear = 1 to 1,812 (tooth ratio 16/29) 2nd gear = 1 to 1,250 (tooth ratio 20/25) 3rd gear = 1 to 1 (tooth ratio 23/23) 4th gear = 1 to 0,833 (tooth ratio 24/20) 5th gear = 1 to 0,730 (tooth ratio 26/19) Ratio: 1:4,125 (tooth ratio 8/33) Overall gear ratios (Engine-wheel): Low gear = 1 to 10,1150 2nd gear = 1 to 6,9761 3rd gear = I to 5,5809 4th gear = 1 to 4,6507 5th gear = 1 to 4,0783 Frame Rectangular section single-beam in NiCrMo steel. Semisupporting engine base. Suspensions Front: White Power upside-down hydraulic telescopic fork with individually adjustable rebound and compression; Rear: steel swing arm with oval cross section. Single shock absorber White Power with separate adjustment of spring preload and of hydraulic rebound and compression damping. Wheels Light alloy castings with 3 hollow spokes (rear wheel with cush drive unit). Rim sizes: – front: 3,50x 17 MT H2 – rear: 4,50×17 MT H2 Tires -front: 120/70 ZR 17 – rear: 160/70 ZR 17 [160/60 ZR 17] Type: Tubeless Front: two Brembo drilled semi-floating disc brakes in stainless steel for SPORT I 100; [two Brembo drilled floating discs, Racing type for DAYTONA RS] with fixed 4 differential piston calipers. Adjustable manual control lever on the right side of the handle-bar; – disc 320 mm;

Incoming search terms:

Moto Guzzi Breva V1100 Repair Manual

0

Filed Under (Moto Guzzi) by admin on 18-11-2010

download
1.2. GENERAL RULES 1.2.1. BASIC SAFETY RULES CARBON MONOXIDE When an operation must be performed with the engine running, position the motorcycle outdoors in a well-ventilated area. Never run the engine in an enclosed place. Use an exhaust emission extraction system when working indoors. DANGER Exhaust gases contain carbon monoxide, a poisonous gas which, if inhaled, may cause loss of consciousness or even death. FUEL DANGER The fuel used to operate engines is highly flammable and becomes explosive under particular conditions. Refueling and maintenance operations should be carried out in a well-ventilated area, with the engine off. Do not smoke when refueling or in the proximity of sources of fuel vapors. Avoid contact with bare flames, sources of sparks and any other source which may ignite fuel or lead to explosion. DO NOT DISPOSE OF FUEL IN THE ENVIRONMENT. KEEP AWAY FROM CHILDREN. HOT COMPONENT PARTS The engine and exhaust component parts become hot when the engine is running and will stay hot for some time after the engine has been stopped. Wear insulating gloves before handling these components or allow for the engine and the exhaust system to cool down before proceeding. USED GEARBOX AND FORK FLUIDS DANGER Wear latex gloves when servicing. Prolonged or repeated contact with gear fluid may cause severe skin damage. Wash your hands thoroughly after handling. Dispose of it through the nearest waste oil reclamation firm or through the supplier. Wear latex gloves when servicing. DO NOT DISPOSE OF FLUID IN THE ENVIRONMENT. KEEP AWAY FROM CHILDREN. BRAKE FLUID WARNING Brake fluid can damage plastic, rubber or painted parts. When servicing the brake system, protect all such parts with a clean cloth. Always wear safety glasses when servicing the brake system. Brake fluid is highly irritant. Avoid contact with the eyes. In case of contact with the eyes, rinse abundantly with cool, clean water and immediately seek medical attention. KEEP AWAY FROM CHILDREN

Incoming search terms:

MOTO GUZZI Quota 1100 ES Specifications And Owner's Manual

0

Filed Under (Moto Guzzi) by admin on 25-11-2010

download
Engine 4-stroke, twin cylinder Cylinder configuration: 90° V-twin Bore: 9 2 mm Stroke: 80 mm Capacity: 1064 cc Compression ratio: 9.5:1 Max. torque: Nm 85 (kgm 8.7) at 3,800 rpm Max. power: Kw 51 (CV 70) a 6,400 rev/min Timing system With rods and rockers and 2 valves per cylinder. One camshaft in the crankcase driven by duplex chain with automatic chain tensioner. Feed system Indirect electronic injection, timed sequential MAGNETI MARELLI IAW 15M “Alfa-N” system, single throttlebody, Weber IW031 injectors, electric pump with pressure regulator, digital control of optimized injection times. Lubrication Pressure fed by gear pump. Wire mesh and cartridge filters on oil sump. Normal lubrication pressure 3.8÷4.2 kg/cm2 (pressure valve on oil sump). Low oil pressure sensor (electrical) on crankcase. Generator / Alternator On front of crankshaft. Output power: 350W at 5000 rev./min. (14V – 25A). Ignition “MAGNETI MARELLI” Inductive discharge digital electronics. Spark plugs: NGK BPR 6 ES. Spark plug gap: 0.7 mm 2 ignition coils Starter Electric starter motor 12V-1.2 Kw with electromagnetic ratchet control. Ring gear on the flywheel. START « » push-button on right handlebar. Transmission Clutch Dry, twin driven plates. Located on engine flywheel. Clutch lever on left handlebar. Primary drive With helical gears, 1:1.3529 (Z=17/23). Gearbox 5-speed, front engaging, constant mesh. Incorporated Cush drive Control pedal on left side of machine. Gear ratios: 1st 1:2 (Z=14/28) 2nd 1:1.3158 (Z=19/25) 3rd 1:1 (Z=23/23) 4th 1:0.8462 (Z=26/22) 5th 1:0.7308 (Z=26/19) Final drive Cardan shaft with gears Ratio: 1:4.125 (Z=8/33) Overall gear ratios (engine-wheel) 1st gear = 1: 11.1618 2nd gear = 1: 7.3433 3rd gear = 1: 5.5809 4th gear = 1: 4.7223 5th gear = 1: 4.0783 Frame Double steel rectangular bar with double cradle

Incoming search terms:

Moto Guzzi Griso V1100 workshop manual

0

Filed Under (Moto Guzzi) by admin on 27-11-2010

download
DIMENSIONS Max. length 2260 mm (88.98 in.) Max. width 880 mm (34.64 in.) Max. height 1070 mm (42.12 in.) (excluding the rear/view mirrors) Seat height 800 mm (31.49 in.) Wheelbase 1554 mm (61.18 in.) Minimum ground clearance 185 mm (7.28 in.) Weight in running order 240 kg (529.1 lb) ENGINE Type twin-cylinder, 90° V transversal, 4-stroke engine Number of cylinders two Cylinder arrangement V, 90° Total displacement 1064 cu cm (65 cu in) Bore/stroke 92 x 80 mm (3.6 x 3.1 in). Compression ratio 9.6 : 1 Starting electric Engine idling speed 1100 ± 100 rpm Clutch dry, twin disc Lubricating system System under pressure, adjustment by valves and vane pump Air filter cartridge, dry Cooling system air cooled TIMING SYSTEM Timing diagram: 2 valves, with rods and rocker arms Values with inspection clearance between rocker arms and valve intake 0.10 mm (0.0039 in.) exhaust 0.15 mm (0.0059 in.) CAPACITIES Fuel (reserve included) 17.2 litres Fuel reserve 3.3 litres Engine oil Engine oil and oil filter change 3600 cu. cm (219 cu in) Gearbox fluid 500 cu cm (30.5 cu in) Transmission fluid 380 cu cm (23.2 cu in) Fork oil 520±2.5 cu cm (31.7 ± 1.5 cu in) (per leg) Seats 2 Max. vehicle load 210 kg (462.97 lb) (rider + passenger + luggage) TRANSMISSION SYSTEM primary drive gear, ratio: 24/35 = 1:1.4583 gearbox Mechanic, with 6 speeds, controlled by a pedal on engine left side overall gear ratios: 1st gear 17/38 = 1:2.2353 2nd gear 20/34 = 1:1.7 3rd gear 23/31 = 1:1.3478 4th gear 26/29 = 1:1.1154 5th gear 31/30 = 1:0.9677 6th gear 29/25 = 1:0.8621 final drive with cardan joint ratio 12/44 = 1:3.6667 FUEL SYSTEM Type Electronic injection (Weber – Marelli) with stepper motor Choke Ø 36 mm (1.417 in.) Fuel Premium grade unleaded petrol, minimum octane rating 95 (RON) and 85 (MON). FRAME Type Tube, with double cradle in high-strength steel Steering head angle 26°30′ Trail 108 mm (4.25 in.)

YAMAHA YZF R6T/ YZF R6TC SPECIFICATIONS AND SUPPLEMENTARY SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
This Supplementary Service Manual has been prepared to introduce new service and data for the,YZF-R6T / YZF-R6TC. For complete service information procedures it is necessary to use this Sup- plementary Service Manual together with the following manual. YZF-R6R / YZF-R6SR / YZF-R6RC / YZF-R6SRC SERVICE MANUAL: CHASSIS TIGHTENING TORQUES NOTE: 1. Insert the front wheel axle from the rightside and tighten it with the flange bolt from the left side to 91 Nm (9.1 m•kg, 66 ft•lb). 2. In the order from the pinch bolt → pinch bolt → pinch bolt , tighten each bolt to 21 Nm (2.1 m•kg, 15 ft•lb) without perform ing temporary tightening. 3. Check that the end face of the axle head and the end face of the fork side are flush- mounted. If they are out of alignment, make sure to fit them by adding the external force by hand or with a plastic hammer, etc. If the end face of the axle is not parallel to the end face of the fork, align them so that one point of the axle circumference is positioned on the end face of the fork. At this stage, it can be accepted if the end face of the axle becomes partially concave to the end face of the fork. 4. In the order from the pinch bolt → pinch bolt → pinch bolt , tighten each bolt to 21 Nm (2.1 m•kg, 15 ft•lb) without performing temporary tightening

HARLEY DAVIDSON VRSC CHROME WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1 WARNING 1 WARNING ® Kit Numbers 41279-04, 41282-04, 41463-05, 41467-05, 41633-05, 41634-05, 41640-05, and 41639-05 1 of 3 Figure 1. Rear Wheel Removal i02495 1. Axle (keep) 2. Axle adjuster (keep) 3. Axle nut (keep) 4. “E”-clip (keep) 5. Spacer (3) (keep) 6. Torx screw (5) (replace) 7. Brake disc (keep) 8. Wheel assembly (replace) 9. Valve cap (keep) 10. Compensator bowl (keep) 11. Compensator cushion (keep) 12.12 pt screw (5) (keep) 13. Lockwasher (5) (keep) 14. Sprocket assembly (keep) 1. Refer to the Service Manual and follow the MAXI-FUSE instructions to remove the right-side cover and maxi- fuse. Proceed to Step 2 for the wheel being replaced. Rear Wheel 2. See Figure 1. Remove the rear wheel per the REAR WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. 4. Re-assemble all saved components to the new chrome rear wheel assembly. See REAR WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Install the compensator bowl with the 12-point screws and lockwashers saved earlier. 6. Install the new wheel to the rear fork. Refer to REAR WHEEL, INSTALLATION in the Service Manual. Proceed to Step 7. Front Wheel 2. See Figure 2. Remove the front wheel per the FRONT WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Mark the left and right brake discs so they can be re-installed to the same location. 4. Re-assemble all saved components to the new chrome front wheel assembly. See FRONT WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. 6. Install the new wheel to the front forks per the FRONT WHEEL, INSTALLATION instructions in the Service Manual. Proceed to Step 7. Front and Rear Wheels 7. Refer to the Service Manual and follow the MAXI-FUSE instructions to replace the maxi-fuse and right-side cover. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) After servicing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. 3. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, part number 99701-84

Incoming search terms:

BMW F800 GS specification And Owner's Manual

0

Filed Under (BMW) by admin on 12-11-2010

download
General view, right side 1 Fuel filler neck (66) 2 Brake-fluid reservoir, rear (91) 3 Vehicle Identification Number (VIN) (on steering-head bearing), Type plate (on steering-head bearing) 4 Brake-fluid reservoir, front (90) 5 Coolant level indicator (behind side panel) (91), Coolant filler neck (behind side panel) (92) 6 Adjuster for springpreload, rear (51) 7 Adjuster for damping characteristic, rear suspension Standard status indicators Multifunction display 1 Clock (38) 2 Odometer and tripmeters (38) Telltale lights 1 High-beam headlight 2 Flashing turn indicators, left 3 Idle 4 Flashing turn indicators, right Service-due indicator If the next service is due in less than one month, the date for the next service is shown briefly after thePre-Ride Check completes. The month is shown as atwo- digit number and the year asa four-digit number, with a colon as separator, so in this example the next service is due in March 2007. 3 22 z Status indicators
If the motorcycle covers long dis- tancesinthe course of the year, under certain circumstances it might be necessary to have it serviced at a date in advance of the forecast due date. If the countdown distance to the odometer reading at whichaservice will be due is less than 1000 km, the distance is counted down in steps of 100kmandisshown briefly after the Pre-Ride Check completes. If service is overdue, the due date or the odometer reading at which service was due is accom- paniedbythe’General’warning light showing yellow. The word “Service”remains permanently visible. If the service-due indicator appears more than a month in advance of the actual due date or if the word “Service”does not show permanently even though a service is overdue, the date stored in memory in the instru- mentpanelis incorrect and must beset. This situation can occur if the battery was disconnected for a prolonged period of time. If you want to have the date set consulta specialist workshop, preferably an authorised BMW Motorraddealer. Status indicators with on-boardcomputerOE Multifunction display 1 Status-indicator panel of the on-boardcomputerOE (39) 2 Gear indicator (23) 3 Coolant temperature (24) 4 Fuel capacity (24) Gear indicator The gear engaged or N for neutral appears on the display.

Incoming search terms: