motor mount bolt size 1998 sportster

You search Auto repair manual PDF motor mount bolt size 1998 sportster, if there are search results will appear below. If search results do not exist, please search by others keyword.



  motor mount bolt size 1998 sportster Direct Download speed 5282 Kb/s

  motor mount bolt size 1998 sportster Full Version speed 6162 Kb/s



TRIUMPH ROCKET III TIP OVER BARS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-12-2010

download
1. Starting on the right side (towards the front of the motor) locate the three mounting bolts that secure the brake assembly bracket (a chrome tube) to the bottom of the motor. Remove the bottom and front bolts. Repeat for left side. 2. Locate the front motor mount bolt. This is the black bolt located at the very front of the engine about halfway down behind the radiator. Remove the nut from this bolt on the left side. Properly secure the bike and use a jack to lift up on the motor to release the pressure from the motor mount bolt. Remove the bolt. 3. On the right side place the motor mount bolt thru the upper mounting hole of the right tip over bar. Install the tip over bar by feeding the motor mount bolt thru the original hole and inserting the two bolts (supplied) into the bottom mounting holes. (Do not tighten yet.) 4. On the left side install the top of the left tip over bar by inserting it into the right side tip over bar. Align the tip over bar so that the motor mount bolt extends thru the upper mounting hole. Thread the original locking nut onto the motor mount bolt a couple of turns. Now align the bottom of the tip over bar and install the remaining two bolts (supplied). Tighten the motor mount bolt (torque to 28-32 ft/lbs) and the lower four bolts (torque to 14-18 ft/lbs) securely. 5. Re-check all hardware for tightness

HARLEY DAVIDSON CHROME OIL FILTER MOUNT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION 1. See Figure 2. Remove oil filter (B). 2. Remove existing oil filter mount screws and washers and remove existing oil filter mount. Discard original screws and washers. 3. Remove original oil filter adapter (A) from old mount. Clean all oil from adapter, then apply Loctite 243 (blue) to the threads on the side of the adapter that mates with the new mount. Install adapter into new mount (1). 4. Place new O-rings (2) from kit into bottom of new chrome oil filter mount (1), place oil filter mount in position, and install new oil filter mount screws (4), lockplate (5), and washers (3) from kit. Lockplate must be positioned as shown in Figure 2. NOTE Carefully follow the instructions for installing the lockplate. Failure to correctly install the lockplate could cause the fasteners to turn and allow the filter mount to loosen. A loose filter mount could allow hot oil to spray onto riders or the motorcycle which could lead to personal injury and/or death. 5. Use Loctite 243 (blue) on threads. Insert upper and lower hex bolts through lock plate. Position flat washer behind lockplate and thread hex bolts into case. Snug bolts but do not tighten. 2 4 1 3 is03977 1. Top bolt 2. Center bolt 3. Lower bolt 4. Center bolt, re-torque Figure 1. Torque Sequence NOTE On FL models, it may be necessary to clip clutch cable strap on frame downtube and move cable to the side. This will allow easier access when tightening new oil mount hex head bolts. 6. See Figure 1. Tighten hex head bolts to 130-140 in-lbs (14.6-15.8 Nm). Tighten hex head bolts starting with top (1), middle (2), bottom (3), then re-tighten middle bolt (4). 7. See Figure 2. Carefully bend over lockplate (5) edges at top and bottom fastener to prevent hex head bolt from turning. 8. Install oil filter (B)

HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

HARLEY DAVIDSON REAR SWINGARM AXLE COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) NOTE XL Sportster 883 and XL1200R models may require loosening or removal of the rear muffler in order to install the right side rear axle cover. See the EXHAUST SYSTEM REMOVAL section of the Service Manual. 1. Support the vehicle, and loosen or remove the rear muffler if necessary. XL Sportster 883 and XL1200R models: Remove the right-side lower shock absorber mounting bolt. Save for re-installation. All other models: Remove and discard the right-side lower shock absorber mounting bolt. 2. Swing the bottom of the shock absorber out of the way. Position the right-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 3. Reposition the shock absorber. XL Sportster 883 and XL1200R models: Install the shock absorber mounting bolt removed in Step 1. All other models: Install the shoulder bolt (3) from the kit. All models: Tighten the bolt to 45-50 ft-lbs (61-68 Nm) . NOTE When torquing the bolt, align two of the bolt-head flats parallel to the ground. This will allow proper orientation of the bar and shield logo on the bolt cover. 4. Position the bolt cover (4) over the bolt head (3) with the Bar-and-Shield logo oriented upright, and lock in place with the set screw (5). Tighten securely. Reposition and tighten the muffler per the Service Manual instructions. 5. Remove and discard the left-side lower shock absorber mounting bolt. Move the bottom of the shock absorber out of the way. Position the left-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 6. Reposition the shock absorber and install the shoulder bolt from the kit. Tighten to 45-50 ft-lbs (61-68 Nm) , aligning two of the bolt head flats parallel to the ground. 7. Position the bolt cover over the bolt head with the Bar-and- Shield logo oriented upright, and lock in place with the set screw. Tighten securely

HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

Incoming search terms:

HARLEY DAVIDSON PIVOT BOLT COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-02-2011

download
This kit fits all 2004 and later XL (Sportster®) model motorcycles INSTALLATION Right-Side Pivot Bolt Cover Installation Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. See Figure 1. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns. 2. Note the position of the bottom-most flat on the rear-fork pivot hex-head bolt (3). Line up the pivot bolt cover over the bolt head so the set screw is centered on the hex flat. Use the 3/32 inch hex key from the kit to tighten the set screw securely to the head of the rear-fork pivot bolt. 3. Make sure the pivot bolt cover is clean and free of any oil or grease. Remove the protective backing from the adhesive disk on the back of the decorative insert (9). Install the decorative insert onto the end of the pivot bolt cover with the image or text upright and parallel to the ground. Press the insert firmly against the end of the pivot bolt cover and hold pressure for 30 seconds. After releasing pressure, avoid direct contact with the insert for about 20 minutes. Left-Side Pivot Bolt Cover Installation 4. Models without passenger footrests: Use an 8 mm hex key to remove the bolt (5) retaining the double-tube clamp (4). Models with passenger footrests: Use an 8 mm hex key to remove the two bolts (5) and the left-side passenger footrest and bracket assembly (6). 5. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns

Incoming search terms:

HARLEY DAVIDSON SPORTSTER FORWARD FOOT CONTROLS

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
LEFT (SHIFTER) SIDE 1. Remove stock footrest assembly and save footrest for reinstallation. Replace existing sockethead capscrews that attached footrest bracket to primary cover with washers (5) and shorter screws (21) from kit. 2. Remove stock shift lever and save shifter peg and mounting screw. 3. See Figure 1. Remove left side stock motor mount and save nuts, washers, and P-clamp for clutch cable. The bolts will be replaced. 4. Put Loctite 243 on threads of left side foot control support (15) and thread support into left side machine motor mount (11). Install C-clip (8) onto support where it exits the backside of machine motor mount to hold support in place. 5. Install left side motor mount assembly in place of stock motor mount using washers and nuts saved from step 3, and bolts (22 and 23) from kit. Tighten bolts to 25-30 ft-lbs (41-47 Nm). Make sure to reinstall the P-clamp and clutch cable in the same hole location they were removed from in step 3. 6. Install shift lever (14) from kit using stock fastener. 7. Put Loctite 243 on threads of clevis mounting screw (4) and install shift lever pedal (13), clevis (17), and footrest (stock), as shown. To install footrest, place a spring washer (19), along with the mount end of the footpeg, inside the slots of the clevis. Make sure the spring washer is positioned inside the clevis with the square edge towards the inside as shown in Figure 3. Secure footpeg and spring washer with bolt (2) and locknut (7). Tighten locknuts to 19 ft-lbs (26 Nm)

RUNE PASSENGER FLOORBOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 21-12-2010

download
1. Remove the seat. Remove the Phillips screws securing the two small black covers on either side of the battery and remove the covers. Next remove the two Phillips screws securing the chrome side covers. Remove the side covers by prying out on the lower front corners with your fingers. Slide the covers to the rear and down to disengage from their rear mounting hooks. Set the covers aside. 2. Beginning on the right side locate the lower sub frame mounting bolt (17mmm wrench size) see (1A) Located behind the sub frame near the head of this bolt you will find a wire clip. Using a blade screwdriver open the clip and push the wires up out of the way. Remove the lower sub frame nut and bolt. Remove the muffler mounting bolt (1B). 3. Locate the right hand mount assembly. Remove the small “L” shaped clamp from the mount. Locate the large (12x 50mm) bolt and two 12mm washers (supplied). Place the bolt thru the hole in the mount. Next place the two washers onto the bolt. Install the assembly onto the frame as shown in photo (2). Reinstall the muffler mounting bolt. It may help to lift on the muffler while trying to get the bolt started). Install the original 12mm flange nut removed earlier onto the new 12mm bolt. Tighten the 12mm bolt and muffler mounting bolts securely (55 ft. lbs. on the 12mm and 12 ft. lbs. on the muffler). Install the “L” clamp as shown in (2A) with the tab facing downward and resting on the muffler mount and tighten securely. Place the wires back into the clip and snap the clip closed

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

HONDA WINCH MOUNT KIT REMOVAL AND Installation

0

Filed Under (Honda) by admin on 12-12-2011

download
Remove the front Plastic Bumper Guard. Remove the U-Bolts from the Winch Mount Plate and place the Winch Mount Plate on top of the horizontal bumper support tubes as shown in picture below. The U-Bolts will be placed around the tubes and up through the plate and are secured with Nylock Nuts. Tighten Fully. (Pictured Below). Mount the Winch to the underside of the Winch Mount Plate using the mount holes in the plate and the provided bolts. Tighten hardware at this time. 3. Using the two 5/16” x 1” bolts supplied with kit, mount the Winch to the Winch Mount Plate. Be sure that when the Winch is mounted to the ATV, the Winch Motor is on the RIGHT side of the machine. 4. Place the front Plastic Bumper Guard back onto the ATV, place the Roller Hawse Mount Bracket against the front Plastic Bumper Guard using the 7/8” Steel Bushings as spacers. Attach using the 6 x 30mm Bolts and Flat Washers. See picture on next page 5. String the Cable through the hole in the Hawse Mount Bracket. Remove one of the long rollers and the two side rollers of the Roller Hawse and feed the winch cable through the Roller Hawse. Reinstall the rollers and be sure rollers move freely.

Incoming search terms: