motorcycle hand shifter kits

You search Auto repair manual PDF motorcycle hand shifter kits, if there are search results will appear below. If search results do not exist, please search by others keyword.



  motorcycle hand shifter kits Direct Download speed 5282 Kb/s

  motorcycle hand shifter kits Full Version speed 6162 Kb/s



TRIUMPH ROCKET III HEEL / TOE SHIFTER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Loosen the 10mm nuts at the ends of the shifter linkage rod (notice one end is a left hand thread). Remove the 10mm nut from the shifter arm & disengage the linkage. Remove the shifter pivot bolt using a 8mm hex key wrench. Remove the washer on the threaded side of the shifter pivot bolt. 2. Place one of the wave washers supplied onto the pivot bolt. Place a small amount of grease on the shifter pivot bolt shank and the Heel / Toe shifter pivot hole, insert the pivot bolt into the pivot hole of the toe heel shifter. Use a drop of blue loctite on the shifter pivot bolt threads and install the Heel / Toe shifter, tighten the pivot bolt securely. Check to see that the shifter pivots freely. If the side play is excessive (this is a result of variances in manufacturing tolerances of the stock and supplied components) remove the pivot bolt and install the second wave washer supplied. 3. Unscrew the linkage rod and replace it with the longer rod supplied (NOTE the rod has a left hand thread on one end and right hand threads on the other). Insert the shifter linkage stud into the desired hole in the new shifter being sure the flats on the stud engage the slot on the backside of the bolthole. Install the nut and finger-tighten only at this time. 4. While seated on the motorcycle first find the height setting you prefer for the toe shifter. Using one of the three boltholes for the linkage can set this. You can also gain some adjustment by exposing more or less threads of the new longer shifter linkage rod; however be sue that you have a minimum of 4-5 threads still engaged in the linkage ends. After setting the height, tighten all three 10mm nuts (the two at the ends of the linkage rod and the one which attaches the linkage to the toe/heel shifter) securely. After you have the toe shifter adjusted to your liking you can select the heel shifter height by moving the button head cap screw that secures the toe shifter to the heel shifter (Using a 5/32″ hex key wrench) next to the 10mm linkage nut to any of its three holes

Incoming search terms:

HARLEY DAVIDSON ALUMINUM SHIFTER LINKAGE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL 1. See Figure 1. Remove stock shifter rod (D). 2. Adjust new shifter rod in kit to match the length of the removed shifter rod by loosening locknuts (3), adjusting the length of the rod, then tightening locknuts to 20-24 ft- lbs (27-32 Nm) . 3. For models with a straight rear shifter rod lever: Discard spacer (7). Place cover (1) over the shifter rod lever (C). For models with an offset rear shifter rod lever: Place spacer (7) and cover (1) over the shifter rod lever (C). INSTALLATION 1. Apply Loctite® 243 to threads of capscrew (5) and install cap screw through the rear of the shifter rod and into the shifter rod lever. Tighten cap screw to 13-16 ft-lbs (18-22 Nm) . 2. For 1999 and later FLHT, FLHX, FLHR, and FXDWG models: Place the rod end on the outside of the shifter lever, then apply Loctite® 243 to the threads of capscrew (5). Attach the front of the shifter rod (6) to the shifter lever with capscrew (5) and acorn nut (4) (with acorn nut facing out). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm) . For all models except 1999 and later FLHT, FLHX, FLHR, and FXDWG: Place the rod end on the inside of the shifter lever then apply Loctite® 243 to the threads of cap screw (5). Attach the front of the shifter rod (6) to the shifter lever with cap screw and acorn nut (4). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm)

HARLEY DAVIDSON DYNA FLOORBOARD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-03-2011

download
Installation SHIFTER ASSEMBLY (LEFT SIDE) 1. Remove highway footrest assembly, if equipped. Discard bracket, plate and mounting hardware. 2. Remove stock footrest assembly. 3. Remove stock (chrome) shift lever. Retain shift lever, peg, bolt and washer. 1 WARNING ® 1 of 5 Kit Number 50601-01 -J01921 2 of 5 Figure 1. Shifter Assembly (Left Side) Item Description Part No. 1 Bolt, 5/16-18 x 5/8 hex HD 2882W 2 Hex cap screw, 5/16-18 x 2.00 (2) 3023 4 Set screw, shaft cover 3231B 6 Assembly,shift lever 33704-01A 7 Assembly,adjustable shifter rod 33719-79B 8 Lever, shifter, machining, polish 33706-01 9 Assembly, shifter plate, polish 33700-01 10 Cover, shifter lever, rubber (2) 34619-85 11 Retainer,shift lever for 1996 to 2000 models 34639-93 Item Description Part No. 11ARetainer bracket, shift lever for 2001 and later models 34639-01 12 Cover, shifter shaft 34640-93 13 Washer, wave, overlap type (2) 34641-01 17 Socket head cap screw 4740A 25 Washer, 5/16″ (2) 6016 28 Washer. 5/16″ 6702 30 Nut, hex, locking, 5/16-18 7710W 32 Acorn nut, 5/16-24 7736 33 Hex jam nut, 5/16-24 7744 30 11 1 12 7 32 28 6 13 9 25 2 17 25 2 10 8 i03110.eps 33 4 11A ’96-2000 models 2001 and later models 4. See Figure 1. 1996 to 2000 models. Bolt shifter lever shaft retainer bracket (11) to the stock shifter lever with bolt (1) and nut (30). Do not tighten bolt at this time. 2001 and later models. Bolt shifter lever shaft retainer bracket (11A) to the stock shifter lever with bolt (1) and nut (30). Do not tighten bolt at this time. 5. Loosen the left rear crankcase bolt (at bottom of cylinder) and slide the slotted end of shifter lever shaft retainer bracket (11) onto the bolt, but beneath the washer. Tighten crankcase stud to 15-17 ft-lbs (20-23 Nm). 6. Place chrome cover (12) on shifter lever shaft (at primary case) and secure with set screw (5). NOTE Small wave washer (13) goes between foot shifter and bracket. 7. See Figure 1. Place small wave washer (13) on shifter lever (6) shaft. Coat shaft with Loctite Anti-seize and slide into bracket. 8. Install foot shift bracket (9) using screws (2). Tighten screws to 25-30 ft-lbs (34-41 Nm). 9. Place shifter rod (2) and washers (25) in position. Use short stud on shifter rod to secure shifter rod at the transmission end. Use Loctite 242 (blue) on stud before installing. 10. Install acorn nut (32) and washer (28) at foot shift end. Use Loctite 242 (blue) on acorn nut before installing

HARLEY DAVIDSON SHIFTER SHAFT COVER WITH INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1 2 4 3 5 6 7 is01872 1. Shifter shaft 2. Inner cover 3. Toe shifter lever 4. Outer cover 5. Set screw (for outer cover) 6. Set screw (for inner cover) 7. Casting Figure 1. Shifter Shaft Covers 1. See Figure 1. Remove the stock heel shift lever and toe shift lever (3) from the gear shifter shaft (1). 2. Install the set screw (6) into the inner gear shifter shaft cover (2). 3. Install inner gear shifter shaft cover with installed set screw over the casting (7) in-board of the shifter shaft (1). 4. Tighten the set screw until light contact is made with the casting. Do not overtighten. 5. Re-install toe shift lever on the gear shifter shaft. Tighten the shifter retaining screw to 18-22 lb-ft (24-30 Nm) . 6. Install the set screw (5) into the outer gear shifter cover (4). 7. Install outer gear shifter shaft cover with installed set screw over the end of the gear shifter shaft (1). 8. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw. SERVICE PARTS

Incoming search terms:

HARLEY DAVIDSON SOFTAIL EXTENDED REACH CONTROLS KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
PREPARE THE MOTORCYCLE 1. For models equipped with saddlebags: Remove the saddlebags following the instructions in the appropriate Service Manual. 2. Remove the seat following the directions in the Owner’s Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect the negative battery cable. 4. Secure motorcycle in upright position. NOTE This kit is not compatible with engine guards. 5. If the engine guard is present, remove and discard it. LEFT SIDE Component Removal 1 3 4 2 7 5 6 8 2 is05048 1. Pretzel clip 2. Bushing (2) 3. Screw (6) 4. Jiffy stand bracket 5. Bumper 6. Jiffy stand leg 7. Clevis pin 8. Spring Figure 1. Jiffy Stand 1 2 3 5 4 is05053 1. Jam nut 2. Shifter rod end 3. Acorn nut 4. Shifter rod 5. Shifter arm Figure 2. Shifter Linkage 1. For HDI Vehicles: Remove the left side foot control support, and jiffy stand sensor, jiffy stand and spring, shifter linkage, shift lever and footpeg following the instructions in the appropriate Service Manual. For all other models: Remove the left side foot control support, jiffy stand and spring, shifter linkage, shift lever and footpeg following the instructions in the appropriate Service Manual. NOTE Two bearing sleeves will remain inside the footrest bracket. The extended controls bracket from the kit will include two sleeves pressed into the bore of the shift lever arm support. 2. Remove rod ends and jam nuts from the shifter rod. Save the rod ends and jam nuts for installation. Component Installation 1. See Figure 9. Select shifter mounting assembly (6), O- rings (5), nylon washer (4) and the shift rod (1) from the kit. 2. Install the shift arm and new O-rings in the bracket. 3. Apply LOCTITE 243 Threadlocker and Sealant to the three mounting screws and mount the shifter bracket with shift arm to the frame. Tighten the mounting screws to 25-30 ft-lbs (33.9-40.7 Nm)

Harley-Davidson Motorcycle Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 Figure 2. Exposed Shoulders Mark shifter fork rod flush with case Remove Spacers Vehicle Transmission Counter Shaft Main Shaft Front of Motorcycle Figure 1
Reverse Gear Installation Instructions For EVO / 5 Speed and Twin Cam Harley-Davidson® Motorcycle Page 3 of 6 Revision 7 © 2007 Champion Motorcycle Accessories International, Inc. dba Champion Sidecars 11841 Monarch Street Garden Grove, CA 92841 (800) 875-0949 (714) 847-0949 www.championsidecars.com www.championtrikes.com Figure 6 CAUTION: Do not pull the shifter fork rod out of the transmission more than 1/4″. If you pull the shifter fork rod out too far, it will be difficult to realign it with the internal shifter fork. 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

Vengeance Motorcycle Specification And Owner's Manual

0

Filed Under (Vengeance) by admin on 20-11-2010

download
Vengeance Maxis • Vengeance Raven • Vengeance Banshee • Vengeance Whiplash • Hotrod Drifter • Hotrod CalChop • Hotrod Teacher • Hotrod Bone Shifting Gears Starting off and changing gears requires coordination of the clutch and throttle and gearshift lever. If you don’t do things right, the amount of control you have over the bike is lessened. To start off, pull in the clutch, shift into first gear, roll on the throttle a little, and ease out the clutch. You will become familiar with the friction zone (that’s where the clutch begins to take hold and move the bike), and you add a bit more throttle. You don’t want to stall the engine, nor do you want to over-rev it. There’s a sweet spot in there; find it. Shift while traveling in a straight line. Shifting in a curve is not good practice, and something to be avoided. Become familiar with the sound of your engine, so you can tell when you should shift without looking at your instruments. When you downshift to a lower gear, you should (in one swift, smooth movement) be able to squeeze the clutch, rev the engine a little to let it catch the lower gear smoothly, and shift down. When you come to a stop in traffic, leave the bike in first gear with the clutch disengaged (just in case you want to accelerate out of there in a hurry). Who knows what may be coming up behind you. Braking Don’t ever forget: The front brake on your motorcycle can supply as much as 70 percent or more of your stopping power. The single most important thing you can learn about braking is to use that front brake every single time you want to slow down. Turning When you are riding along the road, you lean a motorcycle into a turn. Learning to lean is an essential part of riding a motorcycle. It is a normal function of the bike when you are changing its path of travel – and quite different from turning the steering wheel of your car. To get the motorcycle to lean in a normal turn, press the handlebar in the direction of the turn and maintain slight pressure on that handlebar to take you smoothly through that particular turn. In other words: press right to go right; press left to go left. Your instincts to keep the motorcycle on a smooth path while keeping it from falling over usually take care of this without you even noticing it. (Demonstrate to yourself how a motorcycle moves by pressing a handlebar slightly while traveling in a straight line. The motorcycle will move in the direction of the handlebar you pushed.) • Slow down before you enter the turn; look as far ahead as possible through the turn. • Keep your feet on the pegs, and grip the gas tank with your knees. • Lean with the motorcycle; don’t try to sit perpendicular to the road while the motorcycle is leaning over. • Keep an even throttle through the turn, or even accelerate a little bit. Checking the Bike before the Ride It’s not fun to have things go wrong on a motorcycle, but if you spend a minute before you go off on a ride, you can increase the chances that nothing will.

Incoming search terms:

harley- davidson DYNA BLACK FORWARD CONTROL KIT installation Manual

0

Filed Under (Harley Davidson) by admin on 15-03-2012

download
1. Disconnect battery cable, negative (-) cable first. 2. Remove the left side rider footrest assembly. Save the footrest and fasteners for installation. Discard the remaining hardware. 3. From the kit, press hole plugs (8) into the screw holes on the frame where the stock footrest assembly was mounted. 4. Remove plugs from forward control frame mount (I) and discard. 5. Remove the foot shifter lever (A) and shifter peg (D). Discard the old foot shifter lever (A). Save the foot shifter lever hardware and shifter peg (D) for future use. 6. See Figure 2. Remove the primary chaincase cover (6) and primary chaincase housing (1). Refer to your model motorcycles Service Manual for removal procedures. NOTE See Figure 1. Before removing the gear shifter lever (1) ((H) in Table 1), it is necessary to mark the correct orientation of the lever. Using a marking tool, draw a location marking (4) on the end of the splined shaft (2) across from the casting split (3). This will allow the new gear shifter lever to be installed in the same orientation as the old lever. 5 3 4 1 2 is 02083 1. Gear shifter lever 2. Splined shaft 3. Casting split 4. Location marking 5. Lever bolt Figure 1. Gear Shifter Lever Orientation 7. After marking the gear shifter lever orientation, loosen the lever bolt (5) and remove the old shifter lever. Discard the old gear shifter lever but keep the lever bolt. From the kit, install the new gear shifter lever onto the splined shaft in the same orientation as the old shifter lever. Tighten the lever bolt to 18-22 ft-lbs (24.4-29.8 Nm)

HARLEY DAVIDSON FLAME SHIFTER PEG/ HEEL REST PAD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION NOTE A Service Manual for your motorcycle is available at your Harley-Davidson Dealer. To enhance the flame pattern, orient the pegs as shown in Figure 1. 1. If replacing shifter peg, remove and discard existing shifter peg. If needed, apply heat with a heat gun to shift lever threads and threads on shifter peg to aid peg removal. If installing heel rest pads, proceed to Step 3. 2. See Figure 1. Using screw (6), attach shifter peg casting (1, 2) to shift lever. Tighten screw to 16.3-19 Nm (12-14 ft-lbs). NOTE Screw (6) has a lock patch to prevent loosening. 3. To install heel rest pads, perform Step 2 to attach the heel rest to the right or left heel rest lever

HARLEY DAVIDSON SKULL SHIFTER PEG/ HEEL REST PAD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
Models Shifter Peg Kit, Part Number 34689-04 is designed for installation on all model Harley-Davidson motorcycles. Heel Rest Pad Kit, Part Number 34699-04 is designed for installation on all models equipped with a Heel Rest Kit, Part Number 50227-01 or 50236-01. INSTALLATION Shifter Peg 1. Remove and discard the original equipment shifter peg. If needed, use a heat gun to apply heat to the shift lever and shifter peg threads to aid in peg removal. 2. See Figure 1. Using the screw (5), attach the peg (1) and tread (3) assembly to the shift lever. Tighten the screw to 12-14 ft-lbs (16.3-19 Nm). Heel Rests NOTE The chrome heel rest covers are side-specific. For best appearance, install so the HARLEY-DAVIDSON text is above the skull, and the MOTORCYCLES text below . 1. See Figure 1. Using the screws (5), attach the left-side heel rest (1) and tread (3) assembly to the left-side heel rest lever. Tighten the screw to 12-14 ft-lbs (16.3-19 Nm). 2. Repeat for the right-side heel rest (2) and tread assembly

Incoming search terms: