motorcycle passenger foot peg shim spring

You search Auto repair manual PDF motorcycle passenger foot peg shim spring, if there are search results will appear below. If search results do not exist, please search by others keyword.





1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

V-Star 1100 Floorboard/ Foot peg Extension Kit Installation Manual

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Take notice of the position of the shift peg positions relative to the floorboard or foot-peg. You will be adjusting it back to these locations upon installation of the extended linkage. 2. Loosen the shifter rod jam nuts and remove the OEM shift linkage. 3. Loosen the floorboard/foot-peg assembly by removing the mounting bolts (14mm wrench) 4. Install the Extension Bracket using the OEM bolts and torque to 46 ft. lbs. Figure 1 shows how to orient the bracket relative to the front of the motorcycle. 5. Mount the floorboard/foot-peg assembly to the Extension Bracket using the SS hardware provided and torque to 46 ft. lbs. It is always a good idea to apply thread-locking compound such as lock- tite to ensure that the hardware does not vibrate loose while riding. 6. Remove the jam nuts from the OEM shift linkage and thread them gently on to the new shift linkage. 7. Install the new shift linkage by aligning the control swivel and the shifter swivel and turning the linkage. Be careful not to cross thread the linkage. The linkage will thread into both swivels simultaneously. Adjust to the desired position and tighten the jam nuts that you removed from the OEM linkage. Do not over-tighten or damage will occur to the threads. Right Side Installation: 1. Take notice of the Brake pedal position relative to the floorboard/foot-peg before removal, as it will need to be readjusted upon installation of the kit. 2. Remove the cotter pin from the brake linkage and remove the clevis pin. The brake linkage will now be separate from the brake pedal assembly. Do not discard anything. 3. Loosen the floorboard/foot-peg assembly by removing the mounting bolts (14mm wrench) 4. Install the Extension Bracket using the OEM bolts and torque to 46 ft. lbs. Figure 1 shows how to orient the bracket relative to the front of the motorcycle. 5. Mount the floorboard/foot-peg assembly to the Extension Bracket using the SS hardware provided and torque to 46 ft. lbs. It is always a good idea to apply thread-locking compound such as lock- tite to ensure that the hardware does not vibrate loose while riding. 6. Loosen the jam nut from the brake linkage and remove the linkage bracket. 7. Assemble the threaded brake linkage extension to the coupling nut and tighten using one of the provided jam nuts. Don’t forget the thread locking compound if your using it. 8. Thread the coupling onto the brake cylinder linkage and install the other end of the assembly into the brake pedal end. Tighten the jam nuts. You should be able to adjust the linkage for proper brake pedal location before tightening the jam nuts. 9. Readjust the brake light switch and your ready to roll

Incoming search terms:

Yamaha Road Star Forward Control Kit Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Before starting to assemble this forward kit on your motorcycle check the packing list to make sure that the kit you received is the correct one for your model motorcycle and that the foot pegs are the style you ordered (billet or ISO). Next check the contents hardware kit P.N.0109-1000 against the packing list for completeness. Installing The Shift Control Photo 1 Remove wires from horn. Remove the two hex head bolts (Save for later installation) that mount the OEM shift controls to your motorcycle. Unthread stock shift rod at trans shift arm, leaving OEM rod end connected to stock shift arm. Using Original Metric hardware, place a drop of Loctite #242 (blue) to the bolt threads and mount the shift control plate to the motorcycle frame, Photo 2. FORWARD CONTROL KIT PM SHIFT CONTROL ASSEMBLY Note Before torquing the shift control mounting bolts down, tighten them snug and look behind the shift control mounting plate to where it contacts the mounting lug on the frame. Make sure it fits squarely to the lug before proceeding further. Torque the two shift control mounting bolts down to 25 ft-lb. Using a 3/8″ x 1″ hex head bolt with a lock and flat washer put a drop of Loctite #242 (blue) on the threads and insert the bolt through the rear of the control mounting plate and attach the foot-peg pivot to it. Tighten the bolt while holding the footpeg pivot so that its hinge is lined up in a 45˚ rear facing angle. Thread supplied shift rod coupler to stock shift rod end at trans arm. Mount the shift pedal to the other end of the shift ro d using a 5/16″ x 1″ socket head screw and Nylocnut . Adjust the transmission shift linkage so that the shift arm on the forward controls and the shift arm on the transmission are parallel. Secure it with the jam nuts. Apply a drop of Loctite #242 (blue) to the threads under the jam nut before tightening see Photo 3 After you have assembled the shift control onto your motorcycle you must align the footpeg. The folding footpeg assembly uses a blind stud to attach the footpeg to the footpeg pivot. Shim washers (3/8″ x .015″) are used on the stud between the footpeg and the pivot, see Photo 4, so that the top surface of the footpeg is correctly aligned for your foot when it is tightened down on the pivot. This is done by setting a couple of shim washers on the footpeg mounting stud “A” and then screwing the footpeg onto the mounting stud, if the footpeg is rotated to far forward then add another shim washer, if not far enough then remove a shim washer. After you have the selected the correct number of shims for your footpeg, disassemble the footpeg and put a drop of Loctite #271 (red) on both ends of the stud and reassemble the footpeg. This will also need to be done on the brake control footpeg. Setting Up the Master Cylinder The master cylinder pushrod return spring and pushrod boot must be installed on the master cylinder before it is assembled onto the forward control mount. The parts are shown in Photo 5: pushrod boot (A), pushrod return spring (B), spring seat washer (C), and master cylinder (D). Place the return spring seat washer into bore of master cylinder so that is sits on top of the piston retaining snap ring. Next set the pushrod return spring on the seat washer and slide the pushrod boot over the return spring now slip the big end of the boot over the flange on the master cylinder so that the ridge on the inside of the boot fits into groove “A” that is machined into the end of the master cylinder flange, see Photo 6. Installing The Brake Control Unplug stock brake light switch at master cylinder. Remove brake line from rear caliper. Remove the existing brake controls from your motorcycle down to the control mounting lug that is welded on to the frame’s right side, see Photo 8. Save Metric hardware for later use. A Shim Washer PHOTO 4 A B C D PHOTO 5 A PHOTO 6 PHOTO 7 Note For complete brake system removal instructions and precau – tions refer to the appropriate service manual for your year and model motorcycle

Incoming search terms:

KTM Enduro Engineering Shock Spring Removal And Installation Instructions

0

Filed Under (KTM) by admin on 12-11-2010

download
1 Place motorcycle on a stand so that the rear wheel is off the ground. 2 Remove the upper shock bolt. (Figure 1) 3 Remove the lower shock bolt. (Figure 2) 4 Remove the shock from the motorcycle by sliding it down and out the right rear side of the bike. (Figure 3) 5 Place the shock upside down in a vice with soft jaws. Loosen the retaining ring lock screw with a 4mm Allen wrench. (Figure 4) 6 Using EE KTM shock wrench #22-300 (Figure 5), loosen the retaining collar enough to provide ¾ clearance between the bottom of the spring and the spring retaining collar. (Figure 6) 7 Push the spring retaining collar down to access the retaining clip. (Figure 7) 8 Remove the retaining clip. 9 Remove the spring retaining collar by sliding it up and off of the shock clevis. (Figure 8) 10 Slide the shock spring up and off of the shock. 11 Slide the new spring onto the shock. It should be sitting on the adjusting collar. 12 Re-install the spring retaining collar by sliding it over the clevis far enough to allow the retaining clip to be installed. 13 Install the retaining clip. Make sure that it is fully seated in the groove. 14 Slide the spring retaining collar up until it bottoms out on the retaining clip. 15 Tighten the spring adjusting collar until the bottom of the spring contacts the spring retaining collar. Turn the spring adjusting collar a couple more turns to put a small amount of pre-load on the spring. 16 Remove the shock from the vice and re-install it on the bike by reversing removal steps. Make sure to torque the upper and lower shock bolts to the manufacturer’s torque spec. 17 Set static and race sag as specified in your owner’s manual. Remember to torque the adjusting collar lock screw to manufacturer’s specification

Yamaha Virago 750/ 1100 InstaTrike REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 26-12-2011

download
Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike hitch. 1) Place motorcycle on a smooth level surface on center stand. 2) Attach Bracket A (left) to outside of rear passenger foot peg mount. Place spacers between Bracket A and foot peg mount. Use new bolts provided. 3) Attach Bracket B (right) to outside of rear passenger foot peg. Place spacers between Bracket B and foot peg mount. Use new bolts provided. Bracket will extend over top of mufflers. 4) Attach Brackets C (left) and D (right) to rear frame bolts on
motorcycle. Located near rear turn signals Use new bolts provided. (10M x 25mm long) It may be necessary to loosen or remove backrest covers or hardware in order to easily access rear frame bolts. After Bracket C and D installation, reattach and/or tighten backrest mounts. 5) Attach Bracket E(left) / F(right) to bottom of Brackets A & B and to the TOP of the forward hitch arms. Ensure hitch is square on motorcycle and snug bolts for Brackets A, B, and E,F at this time. 6) Raise rear of hitch so bottom of Brackets C & D are flush with top of rear hitch plate. Ensuring that hitch is square with motorcycle, carefully mark hole locations for bottom of Brackets C&D on rear hitch plate. Drill rear hitch plate holes with 3/8 inch drill. This step ensures proper alignment and spacing of hitch on the motorcycle. 7) Tighten all bolts ensuring that hitch is square on motorcycle. Periodically check bolts for tightness. Bracket Identification
INSTALLATION OF THE TOW-PAC HITCH CART.
1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bo

Incoming search terms:

DRIVER PEGS HONDA ADAPTOR INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Assemble the peg onto the peg adaptor by removing the allen bolt from the end of the foot peg you are using. Remove the clevis assembly (folding mechanism) from the peg itself. Assemble the peg and allen bolt on to the peg adaptors. 2. The original peg pivots or folds up on a pin and has a return spring. Note how the spring is assembled into the peg. Remove the cotter pin, washer and pivot pin and foot peg. Install the new peg and adaptor assembly onto the motorcycle in the same manner and using the same spring, pin, washer and cotter pin. Set the angle of the new peg as desired and tighten the allen bolt securely. 3. Use the small set screws located at the end of the adaptors to raise and lower the foot pegs resting position.

AIR / HYDRAULIC MOTORCYCLE LIFT REMOVABLE INSPECTION PLATE

0

Filed Under (Tips and Review) by admin on 19-11-2010

download
For best service, you should incorporate an oiler, regulator, and inline filter, as shown in the diagram on the next page. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. NOTE: If an automatic oiler is not used, put 3-5 drops of pneumatic Tool Oil (not included) in the Motorcycle Lift’s Quick Coupler (38A) before each use. (See Figure B, next page.) To Check The Level Of Hydraulic Oil: 1. The Motorcycle Lift already contains some hydraulic oil in its Hydraulic Pump Reservoir (32P). Even so, it is recommended that you check the oil level in the Reservoir and, if necessary, top off the Reservoir with the proper amount of 15/40 hydraulic oil (not included). (See Assy. Diagram, page 15.) 2. Make sure to screw the two Adjusting Screws clockwise enough to lift the two Caster Wheels (14) off the floor so as to provide stability for the Motorcycle Lift. (See Figure A.) 3. To check the level of hydraulic oil, remove the Sliding Plate (36) from the Platform (35) to expose the Hydraulic Pump Reservoir (32P). (See Assy. Diagrams, pages 13 and 15.) 4. Remove the rubber Filler Plug (33P) located on the top of the Reservoir (32P). If necessary, top off the Reservoir with hydraulic oil. (See Assy. Diagram, page 15.) 5. Connect the air compressor’s hose to the to the Air Motor assembly. Then turn on the air compressor and set its regulator at 120 PSI. (See Assy. Diagram, page 14.) 5. Insert the Lift Foot Pedal (11) onto the Pump Piston Spindle (9), and slowly pump the Lift Foot Pedal until a slight amount of hydraulic oil begins to leak out of the Reservoir (32P). Discontinue pumping the Lift Foot Pedal. Then, replace the Filler Plug (33P) on the top of the Reservoir. (See Assy. Diagram, page 15.) REGULATOR OILER FILTER TO QUICK COUPLER (38A) OF MOTORCYCLE LIFT FIGURE B 6. Insert the Release Foot Pedal (10) onto the Release Valve Spindle (5). Pump the Lift Foot Pedal (11) until the Platform (35) of the Motorcycle Lift reaches its maximum height. Then press down slightly on the Release Foot Pedal until the Platform is fully collapsed to the floor. Repeat this procedure several times to ensure the Motorcycle Lift is operating properly. (See Figure E, page 10.)

Incoming search terms:

SUZUKI M109 ADJUSTABLE HIGHWAY PEG MOUNTS Installation Instructions

0

Filed Under (Suzuki) by admin on 29-12-2010

download
1. Starting on the left side of the motorcycle remove the two 14mm bolts that attach the left foot peg and shifter mounting bracket to the frame. Locate the longer two of the (4) supplied mounting bolts supplied, place a lock washer first and then a washer on each. Locate the left curved main mount (it will have its polished chrome side and the circle of dowel pin holes facing outward when installed on the left side). Place the bolts thru the bolts thru the holes in the mount the slide a spacer (supplied) over each bolt. Place the mount with the bolts and spacers thru the holes of the foot peg and shifter mounting bracket removed earlier and thread the bots into the frame then tighten securely 2. Repeat this procedure on the right side using the remaining shorter bolts, lock washers, washers, mount and spacers and again tighten securely. 3. Again starting on the left side install one of the dowel pins supplied into any of the holes in the mount, place one of the remaining mounting arms (they are the same left and right) onto the dowel pin that is closest to the position you want the arm to be in. Place one of the washers onto the large allen screws then thru the finished side of the arm and thread it into the center hole of the mount. 4. Repeat this procedure on the right side. Loosely install the foot peg set you have selected onto the arms. Sit on the motorcycle to see if you are comfortable with the position you have chosen. You can adjust the position of the arms in Ω” increments forward or back as follows. Remove the arm while leaving the pin in its hole, now move the pin to the next hole forward to rotate the arm back towards the rider Ω” or into the next hole back to rotate the arm forward Ω” and re-install the arm into the corresponding hole that is in the direction you want the arm to go. 5. Adjust the angle of the foot pegs so that they are both comfortable to your feet and will fold up and to the rear when not in use. Set the peg pivot bolts tight enough to hold the in the folded position but loose enough so that you can fold them down with your foot when you need them. Recheck all fasteners for tightness.

HARLEY DAVIDSON FXSTD PASSENGER BACKREST AND LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) INSTALLATION Passenger Upright 1. Unscrew the captive screw fastening the seat rear bracket to the fender. 2. Remove the rubber plugs from the three holes in the rear fender where the passenger upright installs. 3. See Figure 2. Fasten the studplate (2) to the fender (A) with the backing plate (3) and three flange locknuts (4). 4. See Figure 1. Fasten the passenger upright (3) to the studplate (1) with three flange locknuts (2). 5. Insert the seat front bracket into the frame, then fasten the seat rear bracket to the fender. NOTE The seat must be temporarily bowed up in the center to fit the seat rear bracket through the slot in the passenger upright. 6. Kit 51144-02 only. See Figure 2. Carefully clean the lower hole (B) on the passenger upright (1) with isopropyl alcohol to remove any grease or dirt. Remove backing from adhesive emblem (5) and press the emblem firmly in to place. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 1 4 3 2 is03890 1. Stud plate 2. Locknut, flange (3) 3. Passenger upright 4. Backrest pad Figure 1. Passenger Upright, Backrest Pad and Luggage Rack Installation NOTE When temporarily removing the passenger upright, the mounting and backing plates may be left in place to simplify passenger-upright re-installation. Thread the flange nuts back onto studs to store the nuts. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) Backrest Pad See Figure 2. Fasten the backrest pad (7) to the passenger upright (1) using the button-head screw (6) as shown. Luggage Rack NOTE See Figure 2. Fasten the luggage rack (8) to the backrest with the backrest pad (7) removed from the studplate (2). -Fasten the luggage rack (8) to the passenger upr ight (1) using the luggage-rack mounting plate (11), button-head screw (12)

HARLEY DAVIDSON DYNA GLIDE ADJUSTABLE HIGHWAY PEG MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
Installation 1. See Figure 1. Install setscrew (14) into lower hole on frame tube boss (2) leaving .20 in. of setscrew (or three threads) exposed. 2. Place highway peg mounting plate (1) into position. For a lower peg position, place bottom hidden hole in mounting plate over setscrew. For a higher peg position place upper hidden hole in mounting plate over setscrew. Attach mounting plate to frame tube boss using 1 in. long screw (3), lockwasher (4), and flat washer (5) from kit. Tighten screws to 33 ft-lbs. 3. Install footrest support (6) onto highway peg support plate using hex nut (7), lockwasher (8) and flat washer (9) from kit. Tighten nut (7) to 47 ft-lbs. 4. Locate spring washer (10) from kit. While holding spring washer in position on inside of footrest support (with square edge towards motorcycle), position footpeg (not included with this mounting kit) between footrest support mounting tabs, as shown. 5. Insert 1-1/2 in. long screw (12) from kit through footrest support mounting tabs, footpeg, and spring washer. Secure using locknut (13) from kit. 6. Repeat these steps for the other side of vehicle. 1 WARNING These footrest pegs must fold upward and toward the rear at about a 45°angle when retracted. If they do not, peg could contact ground while motorcycle is in a turn, causing loss of control or startling the rider, resulting in possible personal injury. If pegs do not fold up and back at a 45°angle, remove pegs and turn them over so the flat surface is facing forward.

Incoming search terms: