motorcycles sidecar connector

You search Auto repair manual PDF motorcycles sidecar connector, if there are search results will appear below. If search results do not exist, please search by others keyword.





BMW R259 Installation Instructions Fuel Control For BMWOilheads

0

Filed Under (BMW) by admin on 12-11-2010

download
Installation R1200 C -Removethechrome right air filter cover. Release the brake fluid reservoir from its mount. Follow the oxygen sensor lead from the exhaust to the connector. It is mounted to the back of the brake fluid reservoir mounting bracket with cable ties. Cut the cable ties to release the connector from the bracket. Gently pull the connector apart. Insert the male O2 connector from the R259 into the oxygen sensor lead. Connect the female side of the R259sO2 connector to the bike’swiringharness side. Make sure both sets of connectors are fully seated. Cable tie the sensor lead connector back to the bracket and tuck the other O2 connector under the front of theairhorn. -Depressthe retaining bail on the right fuel injector connector and gently pull off the connector. Install this connector on the male R259 injector lead. Install the remaining R259 connector on the right injector. -Connecttheground lead by removing the allen screw (5mmhex) that secures theairboxtothe frame. Place the screw through the lug on the ground lead and reinstall and tighten the screw. Go to section 3 and verify power-up. Tuck the wiring below and behind theairhornand cable tie as necessary. Using the supplied velcro, attach the controller box to the top of theairhorn. Reinstall the brake fluid reservoir in its mount and reinstall the side-cover. Seethe Techlusionwebsite for more detail. Installation R850, R1100, R1150, R1100S -Refertothe appropriate BMW service guides and remove the fuel tank. On some models it maybe possible to have an assistant lift the tank up and to the left to expose the oxygen sensor connector, without fully disconnecting the tank. Locate the oxygen sensor connector by following the lead from the exhaust system. It will be cable tied to the right frame backbone. Cut the retaining cable ties and pull the connector away from the frame. Open the connector and insert the male R259 O2 connector into the oxygen sensor lead, and the female to the bike’swiringharness. Cable tie these back to the right frame backbone. -Routethe R259 wiring harness down the right frame, in-between the battery tray and the rear fuel tank mount. Using the supplied velcro attach the R259 to theairboxlid. Locate the lead on the right fuel injector, and while depressing the locking bail on the connector, gently pull the leadoff. Install this lead on the R259 male injector connector; install the remaining connector on R259 harness to the right injector. Make sure all of the connectors are fully seated. Cable tie any excess wiring away from the fuel lines and throttle mechanism. -Connecttheground lead to the battery negative terminal or an alternate good ground. -Re-install the fuel tank. Make sure the fuel lines are connected and their routing is correct. Insure that both throttle cables are correctly seated in their adjusters on the throttle bodies, and that nothing interferes with the throttle mechanisms on either throttle body. Turn the key on and allow the fuel system to pressurize. CHECK FOR ANY FUEL LEAKS and repair as necessary. Go to section 3 to verify power-up. Re-install any other bodywork removed. Seethe Techlusionwebsite for more detail.

Incoming search terms:

Installation Instructions Fuel Control For BMW Oil heads

0

Filed Under (BMW) by admin on 26-10-2010

download
Removethechrome right air filter cover. Release the brake fluid reservoir from its mount. Follow the oxygen sensor lead from the exhaust to the connector. It is mounted to the back of the brake fluid reservoir mounting bracket with cable ties. Cut the cable ties to release the connector from the bracket. Gently pull the connector apart. Insert the male O2 connector from the R259 into the oxygen sensor lead. Connect the female side of the R259sO2 connector to the bike’swiringharness side. Make sure both sets of connectors are fully seated. Cable tie the sensor lead connector back to the bracket and tuck the other O2 connector under the front of theairhorn. -Depressthe retaining bail on the right fuel injector connector and gently pull off the connector. Install this connector on the male R259 injector lead. Install the remaining R259 connector on the right injector. -Connecttheground lead by removing the allen screw (5mmhex) that secures theairboxtothe frame. Place the screw through the lug on the ground lead and reinstall and tighten the screw. Go to section 3 and verify power-up. Tuck the wiring below and behind theairhornand cable tie as necessary. Using the supplied velcro, attach the controller box to the top of theairhorn. Reinstall the brake fluid reservoir in its mount and reinstall the side-cover. Seethe Techlusionwebsite for more detail. Installation R850, R1100, R1150, R1100S -Refertothe appropriate BMW service guides and remove the fuel tank. On some models it maybe possible to have an assistant lift the tank up and to the left to expose the oxygen sensor connector, without fully disconnecting the tank. Locate the oxygen sensor connector by following the lead from the exhaust system. It will be cable tied to the right frame backbone. Cut the retaining cable ties and pull the connector away from the frame. Open the connector and insert the male R259 O2 connector into the oxygen sensor lead, and the female to the bike’swiringharness. Cable tie these back to the right frame backbone. -Routethe R259 wiring harness down the right frame, in-between the battery tray and the rear fuel tank mount. Using the supplied velcro attach the R259 to theairboxlid. Locate the lead on the right fuel injector, and while depressing the locking bail on the connector, gently pull the leadoff. Install this lead on the R259 male injector connector; install the remaining connector on R259 harness to the right injector. Make sure all of the connectors are fully seated. Cable tie any excess wiring away from the fuel lines and throttle mechanism. -Connecttheground lead to the battery negative terminal or an alternate good ground

Ignition Upgrade Module for 2004-up Carbureted Harley Davidson Motorcycles Owner's Manual

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
1. Disconnect the negative battery cable. 2. Grasp the sides of the electrical caddy (located next the ignition coil) and pull outward to remove. 3. Remove the relay and fuse panels from the electrical caddy. a. Insert a small screwdriver into the slot under each fuse and relay panel. b. Using a screwdriver, disengage the panel from the electrical caddy. 4. Disconnect the main fuse connector from the electrical caddy a. Remove the main fuse from the connector b. Insert small screwdrivers into the slots on each side of the main fuse c. Depress the tabs of the main fuse connector to disengage it from the electrical caddy
Thunder Heart Performance Corp. 615-672-8811 www.thunder-heart.com 2 EI5075.doc 5. Depress the tab located on the electrical caddy securing the TSM/TSSM. Pull it from the electrical caddy. Disconnect the TSM/TSSM connector. 6. Slide the data link connector towards the front of the motorcycle to disengage it from the electrical caddy. 7. Disconnect the ignition control module connector. 8. Disconnect the ignition coil connector and spark plug cables from the coil. 9. Remove the electrical caddy fasteners (3 total). 10. Remove the wiring from the electrical caddy. 11. Remove the fasteners securing the factory ignition control module from the electrical caddy. 12. Installation of the Digital Ignition Module is the reverse of removal. 2.2 Touring Models 1. Disconnect the negative battery cable. 2. Remove the right saddlebag. 3. Gently pull the side cover from the frame downtubes (no tools required). 4. Depress the external latches and use a rocking motion to remove the electrical connector from the ignition control module. 5. Remove the two socket screws to detach the ignition control module from the electrical bracket. 6. To install the Digital Ignition Module, install and tighten the socket screws to 50-60 in-lbs . The remainder of installation is the reverse of removal. 2.3 Softail Models 1. Remove the seat. 2. Disconnect the negative battery cable. 3. Remove the two screws to free the ignition control module from the mounting bracket. 4. Depress the external latches and use a rocking motion to remove the electrical connector from the ignition control module. 5. To install the Digital Ignition Module, install and tighten the socket screws to 15-21 in-lbs . The remainder of installation is the reverse of removal

Incoming search terms:

HARLEY DAVIDSON CLUTCH CABLE ASSEMBLY INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
36753-87A This kit fits 1987 and later FXLR model motorcycles. 36755-87A This kit fits 1987 and later FXRS/SP model motorcycles. 38601-89 This kit fits 1988 and later FLTC, FLTC-Ultra, FLHS, FLHTC FLHTC-Ultra and FLHTP model motorcycles. 38606-87A This kit fits 1987 and later FXR, FXRS and FXRT model motorcycles. 38607-87A This kit fits 1987 and later FLST, FXST, FXSTC, FXRP, FLTC, FLHT, FLHTP and FLHTC model motorcycles. 38617-95 This kit fits 1995 and later FXSTSB model motorcycles. 38647-98 This kit fits 1998 and 1999 FXSTB model motorcycles. 38661-00 This kit fits2000 and later FXDL, FXDS-CONV and FXDWG model motorcycles. 38664-00 This kit fits2000 and later FXSTD model motorcycles. 38665-00 This kit fits2000 and later FXSTB model motorcycles. 38666-00 This kit fits2000 and later FXSTS, FLSTS, FLSTC, FLSTF, FXDX, FXD and FXST model motorcycles. 38667-00 This kit fits 2000 and later FLTR, FLTRI, FLHT, FLHTC, FLHTCI, FLHTCUI, FLHR, FLHRI, FLHRCI and FLHP model motorcycles. 38672-01 This kit fits 2001 and later FXDWG2 model motorcycles. Kit Contents: QTY DESCRIPTION 1 O-ring, rubber 1 Cable, clutch 1 Pin, cable pivot 1 Grommet (Kit no. 38607-87A, 38660-00A and 38667-00 only) Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson dealer. A SERVICE MANUAL IS NEEDED TO INSTALL THIS KIT. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. 1. Refer to the Service Manual for your motorcycle model. Screw the cable adjuster all the way in to allow for maximum cable free play. 2. Remove clutch hand lever from hand-lever bracket at pivot pin. Remove original clutch cable from hand lever and transmission. Retain anchor pin bushings. 3. See Figure 1. Install lever end of new clutch cable. Position cable eyelet in clutch lever slot. Retain with new cable pivot pin through original bushings. NOTE See Figure 2. When routing cable on models where clutch cable passes through inner fairing (FLHTC, FLHTC-U and FLHTP with fairing), clutch cable eyelet may be too large to pass through clutch cable access hole in fairing. If this is the case, use the template supplied with this sheet to file out a hole to accommodate the new eyelet. Place the grommet included with kit no. 38607-87A, 38660-00A, and 38667-00 in the hole after filing. 4. Secure the clutch lever in the lever bracket with the lever pivot pin and retaining ring. 5. Follow steps outlined in the applicable Service Manual and install the transmission-end of the new cable with O- ring. 6. Adjust clutch cable according to procedure in Service Manual.

Incoming search terms:

HARLEY DAVIDSON V-ROD Fi2000 Fuel Injection Module Installation Manual

0

Filed Under (Harley Davidson) by admin on 15-11-2010

download
1. Flip up seat, to gain access to radiator reservoir area. 2. Remove Dzus fastener to remove simulated fuel tank cover, over airbox housing. Depending on which model V-Rod is being worked on, the front shrouds covering the upper front frame section may also need to be removed. 3. Place Fi2000 in under-seat area, run fuel injector connector harness up right side frame rail between top right frame rail, and radiator overflow tank, see Figure 1. At the rear of the airbox, route the harness below the airbox, and downward next to the inner radiator hose. Unplug both stock fuel injector connectors, on the front and rear injectors between the engine cylinders, see Figure 2. These are disconnected, by depressing the metal springs that are on the end of each female connector. The stock female connectors are marked “F” and “R”, noting which connector goes to the front and rear injector, be sure to pay attention to this. Now connect the longer male Fi2000 connector to the front female H.D. connector. Plug shorter Fi2000 male connector into the stock rear female H.D. connector. Then plug the longer female Cobra connector onto the front stock H.D. injector. Plug the shorter Fi2000 female connector onto the rear injector. Each injector connector pair should rest underneath each respective injector. 4. It is now time to install the oxygen sensor eliminator modules. This product is designed to eliminate the “check engine” light from coming on when the stock oxygen sensors are disconnected on Harley Davidson Motorcycles utilizing fuel injection. The motorcycle has a full “open loop” fuel injection map written in its ECU and the motorcycle reverts to this default map after the oxygen sensors have been removed or just disconnected. 5. Locate the rear oxygen sensor and follow the harness up to the under-seat area behind the radiator overflow tank. Pull the stock connectors up from below the overflow tank and disconnect, see Figure 1. Plug one of the supplied Oxygen sensor eliminators on to the stock male connector. Tuck the connectors back underneath the bracket behind the radiator overflow tank. 6. Now locate the front oxygen sensor on the front headpipe, and trace the oxygen sensor harness back to the connectors tucked between the left front frame rail and plastic radiator shroud, see Figure 3. Pull these connectors out, and disconnect them. Plug the remaining supplied oxygen sensor eliminator on to the stock male connector. Tuck the connectors back in between the frame rail and plastic shroud

HARLEY DAVIDSON SECURITY SYSTEM KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
FL Touring models equipped with a TLE/ TLE Ultra Sidecar will require the additional installation of a Bank Angle Switch Kit (88115-03) and is available for separate purchase. See a Harley-Davidson dealer.INSTALLATION 1. Remove the original equipment (OE) Turn Signal Module (TSM) or Body Control Module (BCM) following the instructions in the service manual. 2. Install the Bank Angle Sensor (BAS) on sidecar vehicles. 3. Install the new turn signal/security module (TSSM) (7), Hands Free Security Module (HFSM) (1) or BCM (9, 11) from this kit, following the instructions in the service manual. Configure the Trike or sidecar TSSM, HFSM or BCM to “Side Car Enabled” using Digital Technician. 4. Install the Hands Free Security Module (HFSM) Antenna and antenna mount (6) if necessary, using the service manual instructions. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) ACTUATION 1. See a Harley-Davidson dealer to activate the key fob to the TSSM, HFSM or BCM. NOTE You can activate the TSSM fob by referring to the procedure in the electrical diagnostic manual. TRIKE AND SIDECAR CONFIGURATION (FL TOURING MODELS ONLY) Only Touring Harley-Davidson Motorcycles are suitable for sidecar use. Consult a Harley-Davidson dealer. Use of motorcycles other than Touring models with sidecars could result in death or serious injury. (00040a) NOTES FL Touring Models equipped with TLE/TLE-Ultra Sidecar require the installation of a Bank Angle Sensor (88115-03). Failure to install and configure a Bank Angle Sensor may result in death or serious injury. Sidecar and Trike configuration of the security system requires the use of a Digital Technician. Consult your Harley-Davidson dealer or the sidecar or Trike service manual for complete details. On vehicles equipped with a sidecar, the security system must be reconfigured from the default solo vehicle setting to the sidecar setting

Incoming search terms:

HARLEY DAVIDSON TLE/TLE-ULTRA SIDECAR ATTACHMENT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL NOTES Refer to the service manual for more information on these generalized steps. Save all removed parts (unless otherwise noted) for installation of this kit or for motorcycle operation without the sidecar. 1. For TLE-Ultra Models: Remove both lower fairings. 2. Remove the bolt and lockwasher securing the right passenger footrest bracket and remove the bracket with footrest. 3. Remove the three right side exhaust heat shields. Some models may require removal of the right side exhaust pipes. 4. Remove stock clutch cable. 5. Remove rear master cylinder/rear brake pedal assembly. Remove rear brake pedal from master cylinder assembly. Remove and save rubber pedal pad and brake pedal. Discard cotter pin. 6. Cut the cable straps holding front oxygen sensor connector to frame bracket. 7. Remove wire harness/brake line clip from right lower frame tube. INSTALLATION New Clutch Cable Installation 1. Refer to the service manual and follow instructions to remove stock clutch cable. 2. Refer to the service manual and follow instructions to connect the new clutch cable to clutch hand lever. 3. For FLHT/C/CU: Follow the instructions in the service manual to route new clutch cable through fairing. 4. For FLHR/C Models: Capture the cable in a clamp at the left upper passing lamp bolt. On FLTR models, capture the cable in a clamp at the left upper bolt securing the speedometer and tachometer housing to the upper fork bracket. These locations are identical with stock cable routing. 5. See Figure 1. Route clutch cable down along left frame downtube (1). 6. Continue to route cable down between left front engine isolator and crankcase. Clutch cable will cross to the right side of motorcycle beneath the crankcase, to the clutch release cover on the right side of the transmission. 7. Install clutch cable fitting into clutch release cover. Refer to the service manual. NOTES The final positioning and attachment of the clutch cable and clutch cable adjustment will be performed after sidecar mounts have been installed. Verify that the clutch cable and the rear brake line do not make contact. Damage could result. 1 2 3 is05785 1. Downtube 2. Clutch cable 3. Route clutch cable behind left front engine iso- lator Figure 1. Route Clutch Cable Relocating Oil Pressure Sending Unit NOTES Perform this procedure on all models equipped with an oil pressure gauge or Police models. All other models proceed to “Master Cylinder Assembly/Rear Brake Pedal Modification.” 1. Remove cable strap securing oil pressure wire harness to frame. 2. Locate the latch on connector to oil pressure sender (next to lower right frame downtube). Raise latch on connector and disconnect connector from oil pressure sender. 3. Remove the oil pressure sender using a 1-1/16 inch open- end crowfoot wrench. 4. See Figure 16. Coat threads of elbow (44) with Loctite 565 and install into crankcase oil pressure sender threads. 5. See Figure 2. Install elbow (1) until snug so open end is in the five-o’clock position (2). Do not over-tighten or crankcase may be damaged. 6. Coat threads of oil pressure sender with Loctite 565 and install into 90 degree brass elbow. Use a 1-1/16 inch open- end crowfoot and tighten to 96-120 in-lbs (11-14 Nm) . 7. Install connector on oil pressure sender unit. Verify that slight clearance to the right engine isolators is present. Adjust position of elbow as required to provide clearance

HARLEY DAVIDSON NARROW CHROME DIRECTIONAL BAR INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
This kit is designed for installation on 1986 and later FLST®, FLSTC®, FLSTN®and 1991 and later Touring models. (Except 2004 and later FLHRS®and FLTR®) NOTE: Will not fit when equipped with Flat Lens Turn Signal Module (Part Number 91699-99A). Installation 1. Disconnect turn signal wires. For 1999 and later models: See Figure 1. Remove taillight cover and disconnect turn signal wires at connectors shown in illustration. For 1998 and earlier models: Disconnect turn signal wires at connectors located in directional bar. On 1994 and later models there are two wires for each turn signal lamp. Earlier models have only 1 wire per lamp. 2. Remove existing directional bar from motorcycle and save hardware for re-installation. If the turn signal connector is too large to be removed from the directional bar, remove the wires from the connector as follows: Bend back the connector latches on the sides of the connector slightly to free the secondary lock. Rotate the secondary lock outward on hinge to access terminals in chambers of connector housing. With a paper clip sharpened to a chisel point, insert the paper clip into the connector housing cavity until it stops. Pivot the end of the paper clip and gently tug on the wire to pull the terminal from the cavity. Do not tug on the wire until the tang that holds the terminal in the cavity is released. Take your time, a few tries may be required before you develop a feel for releasing the terminal from the connector. 3. Remove screws that mount turn signals lamps to existing directional bar. Remove lamps and turn signal wires (with their attached connector halves) from existing bar. 4. Position directional bar in mounting location at rear fender and secure bar to motorcycle using original hardware removed in step 2. Route turn signal wires from motorcycle back into directional bar, or up to taillamp (if 1999 and later model) and mate connectors. If the wires were removed from the connector in step 2, insert the terminal ends of the wires into the connector until they snap in place, then mate connector halves.

TRIUMPH TWIN CYLINDER MOTORCYCLES WITH POINTS IN THE SIDE CASING INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 30-10-2010

download
1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the petrol tank and/or seat to gain access to the ignition coils, condensors and wiring. 3. For safety, disconnect the battery (preferably both terminals). 4. Remove timing cover. (The Atlas engine has the points housing behind the cylinder head). 5. Disconnect the two wires (usually black-white & black-yellow) and remove the contact-breaker plate. At the other end, these two wires must be disconnected from the ignition coils & condensors. The condensors are no longer required and can be removed. They should not be connected to the electronic ignition system. 6. Remove auto-advance unit. 7. Disconnect the remaining wires from the ignition coils. These come from the ignition switch supply. On the Norton Commando, remove the white-blue wire from the ballast resistor between the two ignition coils; the ballast resistor is no longer required. The colour of this ignition supply wire may be different on some machines; if so check using a test lamp or meter to find the live wire when the ignition is switched on. 8. Find a suitable place for the ignition module, preferably near to the ignition coils. Secure the ignition module to the frame using one or more large cable ties. An adhesive mounting base is provided; this can be affixed to the underside of the module and the cable tie passed through and around the module and frame. Do not completely wrap the module in foam rubber. 9. Using the black coil link wire, connect the negative (—) terminal of one ignition coil to the positive (+) terminal of the other ignition coil. See figs. 1/2 on page 7. 10. Take the black wire from the ignition module, cut to length and fit an insulator and female spade connector to the end. Connect to the negative (—) terminal on ignition coil #2. See figs. 1/2 on page 7. 11. Take the red wire from the ignition module, cut to length and fit an insulator and female spade connector to the end. Connect to the positive (+) terminal on ignition • BLACK COIL LINK WIRE • RED EARTHING WIRE • CRIMP CONNECTORS & INSULATORS • LARGE & SMALL CABLE TIES • CABLE TIE ADHESIVE MOUNTING BASE 3 coil #1. See figs. 1/2 on page 7. 12. For NEGATIVE EARTH electrics go to step 15. 13. For POSITIVE EARTH electrics (standard): Take the white wire from the ignition module, cut to length and fit an insulator and male spade connector to the end. Connect to one of the negative ignition feed wires previously removed in step 7 (white-blue wire for Norton Commando). The other wire (if fitted) is spare and should be covered with insulation to prevent shorting to the frame etc. 14. Take the red earthing wire, fit an insulator and female spade connector on one end and connect to the positive (+) terminal on ignition coil #1. Cut to length and fit a ring terminal on the other end and connect to a good earth point on the frame, ideally the battery positive (+) terminal. For the Norton Commando, the earth tag on the end of the condensor pack can be used (fit a female spade connector to the end of the red earthing wire). See fig.1 GOTO STEP 17

Twin Tec Installation Instructions for TC88A-IH Ignition

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
INSTALLATION ON 2004 MODELS 1. Turn off the ignition switch and disconnect the battery ground cable before proceeding. 2. Refer to Figures 2 and 3 for wiring details. 3. Remove the Gill Module. 4. Cut off the OE 18 terminal AMP connector used with the Gill module. Refer to the terminal list. Crimp new Deutsch terminals on the wires, and install into the 12 terminal Deutsch connector required by the TC88A-IH module. 5. Install the new TC88A-IH module. 6. Reconnect the battery ground cable. INSTALLATION ON 2005 AND LATER MODELS 1. Turn off the ignition switch and disconnect the battery ground cable before proceeding. 2. Refer to Figures 4 and 5 for wiring details. 3. Remove the Gill Module. 4. Cut off the OE 18 terminal AMP connector used with the Gill module. 5. The crankshaft position (CKP), MAP, and engine temperature (ET) sensor share a common ground Daytona Twin Tec LLC, 933 Beville Road, Suite 101-H, S. Daytona, FL 32119 TC88A-IH (386) 304-0700 www.daytona-twintec.com 10/2009 Page 2 return. This is not compatible with the TC88A-IH and some rewiring will be required. The temperature sensor is not used, but does not require removal. 6. Trace the BK/GN ground return wires from terminal B of the ET sensor and terminal A of the MAP sensor to where they join the BK/GY ground return wire from the CKP sensor. Cut the ET and MAP sensor ground return wires off at this point. You can tape up the ground return wire from the ET sensor – this wire will not be used. 7. Extend the ground return wire from terminal A of the MAP sensor up to the ignition module, crimp on a Deutsch terminal and install in position 4 on the Deutsch connector. 8. Refer to the terminal list. Crimp new Deutsch terminals on the remaining wires, and install into the 12 terminal Deutsch connector required by the TC88A-IH module. 9. Use a DVM to verify isolation (no continuity) between terminals 4 and 9 on the Deutsch connector. 10. Verify continuity between terminal A at the MAP sensor and terminal 4 on the Deutsch connector. 11. Verify continuity between terminal 2 at the CKP sensor and terminal 9 on the on the Deutsch connector. 12. Install the new TC88A-IH module. 13. Reconnect the battery ground cable. Terminal List for American IronHorse Ignition Conversion TC88A Deutsch Connector OE AMP Connector Signal Wire Color Code 1 2 +12V Power W/R

Incoming search terms:

Incoming search terms: