motorstar z200 price solo

You search Auto repair manual PDF motorstar z200 price solo, if there are search results will appear below. If search results do not exist, please search by others keyword.



  motorstar z200 price solo Direct Download speed 5282 Kb/s

  motorstar z200 price solo Full Version speed 6162 Kb/s



HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

TRIUMPH ROCKET III SOLO RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 24-12-2010

download
1. Using the ignition key remove the driver’s seat. Remove the three bolts which secure the passenger seat to the rear fender and remove the passenger seat. 2. Place the lock washers and washers onto the three 6 x 25mm bolts (supplied). Place the solo rack onto the rear fender and align the bolt holes in the fender with the holes in the solo rack. Starting with the two lower holes, place the black plastic spacers (two supplied) between the fender and the solo rack. Next insert two of the bolts with the washers thru the rack and spacers then thread into the fender several turns. At the upper hole place the rubber washer (supplied) between the solo rack and the fender. Insert the remaining bolt with washers thru the solo rack, rubber washer and thread into the fender. Tighten all three bolts securely. 3. Reinstall driver’s seat.

HARLEY DAVIDSON FXD SOLO SADDLE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
Removal of Stock Seat 1. Remove screw (6) to detach rear seat mounting bracket (9) from fender. 1996 models will have a nylon washer under the bracket that should also be saved for installation of new seat. 2. Slide seat rearward to unhook front of seat from frame, then pull seat forward out of passenger strap. 3. Remove two capscrews (10) that attach seat mounting bracket to bottom of stock seat. Install original seat mounting bracket to bottom of new solo saddle with original capscrews. Tighten capscrews securely. 4. Remove nut (7) and washer (8) that hold passenger strap (11) in place and remove strap. Installation of Kit Seat This seat is for solo driver use only. Do not attempt to carry a passenger with this solo seat installed. Use of a luggage rack, fender, or tail section as an additional seat may result in death or serious injury. NOTE When a solo seat is installed without a passenger seat, the passenger footpegs or footboards and the passenger grabstrap must be removed. For 1996 models: 1. Slide seat into position until front seat tab engages frame, then place original nylon washer under hole in rear seat mounting bracket and secure bracket to fender with screw (6). NOTE For 1997 models, a retention nut and washer must be installed into the fender hole, covered with a plastic cap, where the rear seat bracket will be attached. A cable strap is included to aid in this installation. For 1997 models: 1. Remove plastic cap from hole in fender where the rear seat bracket will be attached. 2. Place retention nut (3) over cable strap (2) so wide end of nut rests on eye of cable strap. Thread cable strap up under fender and through fender hole. Pull up on cable strap to hold nut snug against underside of fender. 3. With rib on retention nut seated into notch in fender hole, slide retention washer (4) into place from the rear. This will lock the retention nut in place. 4. Slide seat into position until front seat tab engages frame, then secure rear seat bracket to fender with screw (6). Install chrome cap (5) in rear retention nut

HARLEY DAVIDSON TOURING DETACHABLE SOLO TOUR-PAK RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Installation NOTE See Service Parts Ilustration. When installing Tour-Pak to Rack in the following Steps, note that holes on Rack provide two positions for mounting Tour-Pak to desired location. 1. Place Tour-Pak on support tube and open lid. NOTE In the following Step, the longer bolts (Item 7), are used for King and Chopped Tour-Paks while the shorter bolts (Item 6) are used for Leather Tour-Pak. 2. See Service Parts Illustration. Obtain bolt (6 or 7), two flat washers (4), concave spacer (5) and hex lock nut (3) from kit. Align rear center hole in Tour-Pak with same hole in support tube (9). Slide bolt with flat washer through Tour- Pak, through support tube, then through concave spacer (with concave side facing surpport tube). At bottom of support tube, install washer and nylock cap nut (3). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. 3. See Service Parts Illustration. Obtain bolt (6 or 7), flat washers (4), concave spacer (5) and hex Nylock nut (3) from kit. Align the remaining four holes in Tour-Pak over holes in solo rack. Slide bolt with flat washer through Tour- Pak, through support tube (9), then through concave spacer (5) (with concave side facing up) and Solo Rack hole. At bottom of Solo rack, install washer and nylock cap nut (3). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. Always install the mounting bolts from inside the Tour- Pak. If the bolts are installed upside down, then the ends of the bolts can tear the molded liner and scratch objects, such as helmets, stored inside the Tour-Pak. 4. Repeat Step 3 and install hardware to the remaining three holes in Tour-Pak and mounting rack

HARLEY DAVIDSON XL SOLO CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat. 1 2 4 1 3 is03341 1. Stock retention nut and washer 2. Plastic cap 3. Rearward fender hole 4. Center fender hole Figure 1. Retention Nut and Plastic Cap Location 2. For models that had a solo seat: Proceed to Step 3. For models that had a 2-up seat: The retention nut and washer must be moved from the rearward mounting hole to the center fender hole where the rear seat bracket will be attached. Use a cable strap to aid in this step as fol- lows: a. See Figure 1. Remove retention nut from rearward fender hole (3) and plastic cap (2) from center fender hole (4). b. Install plastic cap into the rearward fender hole. c. See Figure 2. Place the retention nut over the cable strap so the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender and through the center fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib of the retention nut seated into the notch in the fender hole, slide the retention washer into place from the rear. This will lock the retention nut in place. 3. Position the solo seat on the motorcycle frame with the mounting bracket at the rear. Bring the seat forward and engage the tab on the seat into the slot at the base of the fuel tank. 4. See Figure 3. Secure the seat to the fender using the knurled knob (3) and neoprene washer (4) from the kit. Install the washer on the knob and tighten the knob securely to the fender seat nut

HARLEY DAVIDSON Detachable Solo Racks removal and Installation instructions

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
installation/Removal 1. While standing behind the motorcycle, place the front rack notches into the front docking points as shown in step 1 of the diagram. (Most of the rack, except a typical sideplate, has been removed for illustration purposes). 1 CAUTION Rear docking points may be damaged if rotary latches and sideplates are not properly aligned. If the latch does not easily close, do not force. Check alignment as described in step 2. 2. Pull the rotary latches back into their rearmost position as shown in step 2 of the diagram. 3. Push downward and close the rotary latches by pressing the latch lever as far forward as it will go as shown in step 3. You will hear a click when the latch is in place. If the latch does not easily close, do not force . Recheck alignment as described in step 2. 4. To remove the rack, press the release button shown in the diagram, and pull the rotary latch lever back. Carefully lift the rear of the rack up and pull the rack out of the front docking points. Position the rear rotary latches over the rear docking points, making certain the latches and sideplates fit into the neck of the rear docking points as shown in the rear view of step 2. This may require some gentle squeezing or spreading of the sideplates. Attaching Solo Rack INSTRUCTIONS -J00256 REV. 8-30-96 Detachable Solo Racks ® i00627 Step 1:place front notches into front docking points Step 2: pull back rotary latches and lower rack onto rear docking points Step 3: close rotary latches by pushing latch fully forward Release button

TRIUMPH AMERICA AND SPEEDMASTER SOLO RACK FITS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Remove the 8mm bolt from the rear of the passenger seat. Remove the passenger seat by pushing the seat forward and lifting up at the front edge of the seat. Remove the 12mm bolt from the rear of the drivers seat. 2. From the supplied hardware locate the two socket head screws and washers, place the large washers onto the screws with the polished side of the washer facing the head of the screws. Place the small screw and washer thru the small hole in the rear of the solo rack, place the black plastic spacer supplied onto the screw on the bottom side of the solo rack. Holding the rack in place on the rear fender, start the screw in the rear hole. Install the remaining large screw with its washer into the front hole and tighten both screws securely.

HONDA VTX 1800R AND VTX 1300R SOLO RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Remove the stock passenger seat. And “U” shaped mounting bracket from the rear fender. 2. Install the 2 “L” brackets provided (NOTE: there is a left and a right) onto the rear fender using the bolts from the stock bracket. Snug the bolts just enough to still allow them to slide. 3. Using the 3 knobs provided re-install the stock seat using the knob with the long stud in the rear hole. Center the slot in the seat and tighten the knob. Install the 2 knobs with the short threaded studs through the front seat mounting holes and into the new brackets. Center the bracket holes to the seat holes and snug the knobs. This will align the forward brackets. Carefully remove all three knobs and the seat. Tighten the forward bracket securely. 4. Install the solo rack starting with the 2 short knobs at the front then the long knob at the rear with the black spacer between the rack and the fender. Tighten all 3 knobs securely, as tight as you can by hand. Lost knobs are not a warrantable item. Now you can switch from your new cool solo rack look back to your stock passenger seat in seconds without any tools. NOTE: when using the stock seat, place the black spacer on the long rear knob and install them over the stock rear seat bracket. This keeps the long stud from extending below the inside of the fender and possibly contacting the rear tire if the rear shocks should bottom out

Incoming search terms:

Harley- Davidson FX/ FL Big Twin 1965-1984 Two-Piece Seat Mounting Suggestions

0

Filed Under (Harley Davidson) by admin on 15-04-2012

download
Stock One-Piece Seat Removal Steps 1. Remove rear fender screw located behind the passenger seat and set aside. The stock rear fender screw will be used to attach your new Mustang Two-Piece Seat. 2. Slide seat back and up. Mounting of Mustang Solo & Passenger Seat 1. Remove two screws from back of Mustang solo seat. 2. Align two chrome tabs located at the front of the passenger seat with the mounting holes in back of solo. 3. Screw rear seat and solo together. 4. Slide solo front forks under frame. 5. Align chrome rear tab located at back of passenger seat with stock hole in fender. 6. Secure in place with stock fender screw to complete the installation process. Note: Use of side brackets optional and would use the rubber expansion plugs, threaded inserts, and bolts used for a solo only installation.

HARLEY DAVIDSON XL DETACHABLE SOLO RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-04-2011

download
Kit Contents See Figure 2 and Table 1. There are no Service Parts available with this kit. INSTALLATION 1. See Figure 2. While standing behind the motorcycle, place the front rack notches (1) into the front docking points (2). NOTE Check alignment as shown in Figure 1. Failure to properly align the docking points and sideplates may result in damage to the rear docking points. 2. Pull the rotary latches (3) back into their rearmost position. Position the rear rotary latches over the rear docking points (6), ensuring the latches and sideplates (4) fit into the neck (5) of the rear docking points. This may require some gentle squeezing or spreading of the sideplates. NOTE The front and rear docking points must be fully engaged. If docking points are not fully engaged or docking kit is loose, it could shift position or come loose during operation. 3. Push down and close the rotary latches by pressing the latch lever (7) as far forward as it will go. You will hear a click when the latch is in place. If the latch does not easily close, do not force. Recheck alignment as described in Step 2. 4 4 3 2 2 1 1 1 2 is 00963 1. Right sideplate 2. Right front docking point 3. Correct: sideplate fully engaged in docking point 4. Incorrect: sideplate NOT fully engaged in docking point Figure 1. Sideplate Must Fit into Docking Point Correctly REMOVAL 1. See Figure 2. To remove the rack, press the release button (8), and pull the rotary latch lever back. Carefully lift the rear of the rack up and pull the rack out of the front docking points

Incoming search terms: