night train feul sending unit

You search Auto repair manual PDF night train feul sending unit, if there are search results will appear below. If search results do not exist, please search by others keyword.



  night train feul sending unit Direct Download speed 5282 Kb/s

  night train feul sending unit Full Version speed 6162 Kb/s



HARLEY DAVIDSON FLHT OIL PRESSURE AND AIR TEMPERATURE GAUGE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION Oil Pressure Sending Unit To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. 1 2 3 4 is04574 1. Oil pressure sending unit 2. Cam position sensor 3. Crank position sensor 4. Main harness to ECM Figure 1. Electrical Bracket: 2000-2001 Fuel Injected Models (Magnetti-Marelli) 1 2 3 is04575 1. Oil pressure sending unit 2. Crankshaft position sensor 3. P&A siren kit Figure 2. Electrical Bracket (ECM Removed) 2002-2003 Fuel Injected Models (Delphi) -J01875 1 of 4 NOTE For 2002 to 2003 models: See Figure 2. Remove the two screws securing the ECM and remove the ECM to access the electrical bracket. 2. For 2004 and later models: Proceed to the Gauges section. For 2000 to 2003 models: See Figure 1, Figure 2 and Figure 3 for the applicable model and locate the sensor harness connector (2-piece mini-Deutsch® connector). 3 2 4 1 is04576 1. Ignition harness 2. Cam position sensor 3. Oil pressure sending unit 4. Crankshaft position sensor Figure 3. Ignition Module – Carbureted Models 3. Locate the oil pressure sending unit at the front right side of the crankcase and pull wire socket from terminal of the oil pressure sending unit. 4. Carefully draw the conduit and the pin side of mini-Deutsch connector forward and then up between the rear brake master cylinder reservoir and the frame downtube to area of the rear brake pedal. 5. See Figure 4. Remove the secondary locking wedge (3) from the pin side of the connector with a needle nose pliers. 1 3 2 is04577 1. Pin 2. Wire seal 3. Locking wedge Figure 4. Deutsch Connector Pin Side (2-pin connector shown) 6. Gently depress terminal latches inside pin housing and back out the pin in chamber #1 through the hole in wire seal. 7. Pull the oil sending unit wire through conduit and remove wire. Note the routing of the wire. 8. See Figure 9. Route the jumper (6) pins through the conduit from the kit in the same direction as the original wire noted in Step 7. Use cable straps to secure to the wire bundle. 9. See Figure 5. Locate pin chambers #1 and #2 on pin side of connector. Insert brown/green jumper pin into chamber #2 and feed until it clicks into place. Verify that pin will not back out of the chamber by giving a slight tug on the wire to confirm that it is locked

Incoming search terms:

Honda Motorcycle Digital Audio System Owner's Manual

0

Filed Under (Honda) by admin on 22-11-2010

download
Applicable portable audio unit A commercially available portable audio player with a stereo mini jack terminal can be connected to this accessory. (An attachment kit designed for the model is necessary to connect the portable audio player to this accessory.) American Honda Motor Co., Inc. recommends you use a shock-resistant portable audio player such as a flash-memory player (e.g. MP3, etc.) or an MD player equipped with sound skip prevention function. American Honda Motor Co., Inc. also recommends you always ride your motorcycle safely on paved roads, because sound skip can occur during riding on rough roads. Refer to the following instructions on storage and handling of the portable audio unit. This accessory is not designed to operate the portable audio unit connected to the accessory. Refer to the portable audio unit manufacturer’s Owner’s Manual for how to operate the portable audio unit and operate it accordingly. Note that the warranty of this accessory does not cover function and failure of the portable audio unit connected to the accessory 5 Storage of portable audio unit connected to this accessory After connecting the digital audio system, put the portable audio unit in a stable place where it does not interfere with riding the motorcycle (e.g. in the sold separately front pouch, tank belt pocket, etc.) in a place free from vibration as much as possible. Do not place the portable audio unit in your pockets or clothes while connected to this accessory. The portable audio unit can vibrate and contact other materials while riding, causing a sound skip. To prevent such skips, store the portable audio unit in a suitable place while protecting it from vibration and shock by covering it with cushioning material. (Protect the remote control and peripheral devices as well as the portable audio unit.) Any system failure and damage to the portable audio unit and its peripheral devices are not covered by the warranty of this accessory.

Incoming search terms:

TOYOTA SPECIALTY AND REPLACEMENT PARTS

0

Filed Under (Toyota Manuals) by admin on 30-09-2011

download
73-3844 Replaces: 3977775, 3078511 CLIP -HOOD INSULATION Head Dia.: 2″ Length: 3/4″ G.M. ’64/ UNIT PACKAGE 100 79-5126 Replaces: 20064875 CLIP -HOOD INSULATION Head Dia.: 1 21/32″ Length: 3/4″ G.M. ’78/ UNIT PACKAGE 50 79-5127 Replaces: 20030401 CLIP -HOOD INSULATION Head Dia.: 1 3/8″ Length: 1″ G.M. ’80/ UNIT PACKAGE 50 79-5100 Replaces: 388908-S RETAINER -HOOD INSULATION Head Dia.: 1-3/4″ Ford ’80/ UNIT PACKAGE 100 74-3945 Replaces: 385330-S, 6003351 FASTENER -HOOD INSULATION Ford & Chrysler Products ’73/ AMC 4005513 ’76 UNIT PACKAGE 100 92-7067 Replaces: 15678493, 21039141 RETAINER -HOOD INSULATION Head Dia.: 1-9/16″ Length: 1/2″, Hole: 1/4″ Plastic Saturn ’91/ UNIT PACKAGE 25 67-3119 Replaces: 389809, C6GY-16776-A CLIP -HOOD INSULATION RETAINER 1-1/2″ x 1-1/2″ Plastic G.M., Ford Products UNIT PACKAGE 50 72-3718 Replaces: 389089 FASTENER -HOOD INSULATION 2″ x 2″ Plastic G.M. Cars UNIT PACKAGE 50 99-8032 Replaces: 385595-S, 386553-S RETAINER -HOOD INSULATION Plastic Formerly 74-3944 For Heavier Type Insulation Head: 1-3/16 Ford ’74/ UNIT PACKAGE 50 95-7382 Replaces: N-803613-S RETAINER -HOOD INSULATION Hole: 1/4″, Head: 1-3/4″ Stem Length: 7/8″ Plastic Ford Explorer ’91/, Taurus, Sable, Mustang, Continental ’92/ UNIT PACKAGE 50 95-7369 Replaces: W700671-S300 RETAINER -HOOD INSULATION Head Dia.: 25MM, Hole: 8MM Black Plastic Ford Contour & Mercury Mystique ’95/ UNIT PACKAGE 15 96-7577 Replaces: 01644290, 15678979, 01553-0075U RETAINER -SPEAKER, DOOR SILL, BUMPER, HOOD INSULATOR Black Plastic Hole: M6, Barb Length: 12MM Head Dia.: 11MM, O/L: 19MM G.M. Various Models ’86/, Nissan Altima & Maxima 2002/

Incoming search terms:

2007 Softail HARLEY DAVIDSON FUEL PUMP/ FUEL GAUGE SENDING UNIT REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
1. Remove seat. 1 WARNING 1 WARNING To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) 2. Purge the fuel supply line of high pressure gasoline. a. See Figure 4-36. Disconnect the fuel pump fuse from the main wiring harness. b. Start the engine and allow the vehicle to run. c. When the engine stalls, operate the starter for 3 seconds to remove any remaining fuel from the fuel lines. 1 WARNING 1 WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect negative battery cable. 4. Remove instrument console. a. All but FXSTD, see Figure 4-37. Remove acorn nut and washer on instrument console to separate console from fuel tank. b. For FXSTD, see 8.26 INSTRUMENT CONSOLE: FXSTD. 5. Disconnect console wiring. Figure 4-36. Fuel Pump Fuse: View From Top Figure 4-37. Acorn Nut And Washer: All But FXSTD s0660x8xx 7526
4-28 2007 Softail: Fuel System HOME 1 WARNING 1 WARNING Gasoline can drain from the crossover line when disconnected from fuel tank. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00259a) 6. Drain fuel tank. a. Obtain a short section of hose (5/16 inch I.D.). Insert bolt in one end of hose and install hose clamp to ensure that end is securely plugged. b. See Figure 4-38. Cut clamp (1) from one end of crossover hose (2). Quickly replace crossover hose on fuel tank fitting with open end of short hose while directing flow of gasoline from free end of crossover hose into suitable container. 7. See Figure 4-39. Unplug fuel pump module connector (3) [86]. 8. Remove top plate screws (2) and discard. 9. See Figure 4-40. Pull top plate (2) out of fuel tank enough to expose fuel hose and clamp (1). CAUTION Carefully inspect end of hose for cuts, tears, holes or other damage. Replace hose if any damage is found. Even the smallest hole can cause a reduction in fuel pressure. 10. Cut clamp and remove hose from regulator housing fit- ting.

Incoming search terms:

ACE -325X/ 395 X-XX CLOCK, UNIT, WHEEL, ODOMETER, TEMPERATURE & FUEL METER SETTING

0

Filed Under (Honda) by admin on 24-12-2011

download
Setup operations include 12/24hour clock, bar tachometer scale, shift warning RPM, numbers of engine rotation per signal, wheel circumference, units, odometer adjustment, units of temperature, temperature warning and fuel meter input resistance selection. These must be set up step by step. The computer will automatic reversion to main screen if no button operation for 75 seconds at any setting screen. 2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1 or convert units, press MODE button to confirm the digit setting and jump to next digit or next setting screen to be set. Press MODE button for 2 seconds at any setting screen to finish the setting and go to main screen. 3. It displays “12 or 24H and XX:XX-XX” symbols and AM/PM in case you select 12H. Operates buttons as descriptions of item 2 to finish clock and jump to 8,000/16,000rpm scale setting. 4. It displays 8,000rpm scale, presess RESET button to convert 8,000 or 16,000rpm. Press MODE button to confirm the setting and jump to shift RPM warning setting. 5. It displays ” RPM rXXX00 “. Follow the item 2 of button operation to finish the shift RPM warning setting and jump to engine specification setting. 6. It displays “SPC-X.X RPM”, the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation per signal. For example the value 2.0 means the engine rotate 2 turns to output a signal. 7. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting and go to wheel circumference setting screen. 8. In “cXXXX” display, “c” means “Circumference”, following 4 default digits; flashing digit is digit to be set. Follow the item 2 of button operation to finish the wheel circumference setting and jump to unit setting. 9. It displays KM/h or MPH, each press of RESET button converts unit; press MODE button to confirm unit setting and jump to odometer setting. 10. It displays “ODO & 00000Xkm”, the “X” is tested odometer in factory, follow item 2 to setting a desired odometer and jump to thermometer unit setting. The setting screen will disappear when the odometer is over 30km or your setting is over 30km and returned to main screen. 11. It displaysm ” , or oFF”, each press of RESET button converts , or oFF; press MODE button to confirm temperature setting and jump to temperature warning setting. 12. It displays ” XXX” and the selected unit. Follow the item 2 of button operation to finish the temperature warning setting and go to fuel sensor input resistance setting. 13. It displays “100r and fuel tank symbol”, follow the item 2 to select 100, 250, 510 Ohm or oFF and return to the main screen. The fuel meter bar will disappear if you select oFF mode.

Incoming search terms:

HONDA CB650/ 750F/ 900F/ 1100F/ GL1100 Spark Unit Set Installation Manual

0

Filed Under (Honda) by admin on 05-04-2011

download
INSTALLATION INSTRUCTIONS: 1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the seat and/or petrol tank to gain access to the original spark units (if fitted); these are normally fitted under the seat between the top frame tubing. Each of these units consists of a small alloy metal box with sleeved wires terminated by a small connector (coupler). They also have a mounting tab with a single fixing hole. 3. On four cylinder machines there will be two units, normally mounted back to back; one for cylinders 1&4 and one for cylinders 2&3. 4. For safety, disconnect the battery. 5. Unplug the couplers from each of the units. Undo the fixings and remove the units. 6. Fit the new spark units in the place of the old ones or find a suitable alternative, close to the connectors. Secure the units to the frame or mounting platform using the supplied tie-straps and adhesive mounting base (if required). If required, a thin sheet of rubber or double-sided tape can be used to keep the units in position. Do not completely wrap the units in foam rubber. 7. Push the wiring harness plugs into the new spark unit socket connectors; they will only fit one way. Reconnect the battery. 8. If you are rewiring the machine or do not have the standard wiring harness, the spark unit wire colours & functions are as follows: GREEN Ö GROUND (0 VOLTS) BLACK/WHITE Ö IGNITION SUPPLY (+12 VOLTS) VIA ENGINE STOP SWITCH YELLOW Ö IGNITION COIL OUTPUT (TO COIL —) WHITE Ö PULSE GENERATOR (WHITE RING) BLUE Ö PULSE GENERATOR (UNMARKED) There are two pulse generators, one for cylinders 1&4 and one for cylinders 2&3. The left hand one is normally for cylinders 1&4 (see fig.1). There are two wires of the same colour coming from each pulse generator, one of these wires is normally marked with a white band. The pulse generator wire with the white band connects to the white wire from the corresponding spark unit, the other pulse generator wire connects to the blue wire on the corresponding spark unit. If the white band is missing, this is normally the upper wire coming from the pulse generator. 9. Refit the seat and tank (if removed earlier). 10. Fitting is now complete, although for best results you may wish to verify the ignition timing, see the following guide

Incoming search terms:

2001-2004 HONDA GL1800/A Trunk Opener Unit Removal/ Installation instructions

0

Filed Under (Honda) by admin on 29-01-2011

download
come customers may experience trunk or saddlebag lids not opening when the corresponding latch lever is pulled. To correct this condition, the opener mechanism must be replaced with a new opener mechanism. Follow the Trunk Opener Unit Removal/Installation instructions in the GL1800/A Gold Wing Service Manual. Opener Unit P/N: 81310-MCA-A22 H/C: 7700768 The normal GL1800/A warranty applies. Follow all normal warranty procedures and guidelines. Labor Operation: 412122 Flat Rate Time: 0.6 If you feel that goodwill consideration is appropriate, contact your District Service Manager or TechLine BEFORE starting this repair. 2001-2004 GL1800/A Trunk Opener Unit MTB 10535 (0403) GL1800/A #15 MAY 2004 REPAIR PROCEDURE PARTS INFORMATION WARRANTY INFORMATION QUESTIONS PART DESCRIPTION TRUNK OPENER UNIT

Incoming search terms:

Honda Shadow Aero 750 Turn Signal Cancellation Unit Installation Procedures

0

Filed Under (Honda) by admin on 29-11-2010

download
Left TurnSignal Right TurnSignal Turn Signal Switch (for ref. Only) CIRCUIT CONNECTIONS AFTER INSTALLATION of Cancellation Unit Original+12 volts motorcycle supply power for flasher Ground (thiswiredoesnot exist on all models) Output to switch Power Power Red Yellow Gray Green Ground Green/Red Blue/Red Turn Signal Cancellation Unit Identify the positive power wire to the turn signal flasher. A test light with the probe touched to this wire will stay on steady and flash with the turn signals. Cut the wire and install the connectors observing the polarity as shown. Connect the Red and Yellow wires as shown. not Identify the flasher output wire to the signal switch and attach the gray wire by soldering or use the supplied red tap connector. Place the unit in a suitable area on your particular motorcycle. It is suggested under the seat providing access to the turn signal flasher. Connect the units ground (green) wire to frame (neg) ground Assure it’sareliable connection. IF THE GROUND WIRE BECOMES DISCONNECTED THE UNIT WILL BURN UP. using the supplied ring terminal. Identify the brake light circuit per the motorcycle wiring diagram. Using a test light verify the correct circuit using the following procedure. Connect the test light alligator clip (negative side) to frame ground. Using the positive tip probe the circuit. The proper circuit will illuminate the the brake is applied. Attach the Green/Red wire to this circuit. test light when The factory cancellation time is set at approximately 23 flashes. The length of time for cancellation can be decreased to approximately 15 counts by setting the program listed in the programming box

Incoming search terms:

Triumph Center Mount Oil Pressure Gauge with active oil light Installation

0

Filed Under (Triumph) by admin on 29-10-2010

download
Remove the two hex head screws and spacers that secure the handlebars. Attach the oil pressure mounting bracket using the bolts removed earlier. It is not necessary to use the spacers as the bracket is the same thickness as the spacers that were removed. Make sure the oil pressure gauge bracket is clamped securely so that the handlebars cannot rotate. This part of the assembly is complete. Do not tighten the fitting mounted on the far side of the Swivel body. This fitting is designed to rotate and is sealed in place with Loctite 242 thread sealant. Over tightening will shear the threads resulting in destruction of the fitting. Remove oil pressure sending unit. Sit the copper crush washer aside for future use. The Swivel and Swivel Adaptor are supplied assembled. Remove the plug from the rear of the Swivel. Slip the crush washer removed earlier over the end of the Adaptor. There is an ‘O’-ring seal between the Adaptor and the Swivel, leaving the two assembled will prevent damage to the seal. Thread the Adaptor, with Swivel still attached, into the port from where the original sending unit was removed. With the use of a 5/32″ Allan wrench, reach inside the Swivel and tighten the Swivel against the Adaptor. Install the original oil pressure sending unit in the top port as shown using the new copper crush washer supplied. Use a wrench on both the Swivel and the original oil pressure sending unit to prevent imparting stress on the Adaptor to Swivel junction. Reinstall the 1/8 NPT plug in the end of the Swivel using with the use of a 3/16″ Allan wrench. Use Loctite 242 or equivalent semi-permanent thread sealant at this junction. Do not over tighten. Use a 3/16″ Allan wrench on the plug and an open end wrench on the Swivel to prevent imparting stress on the Adaptor to Swivel junction. Next, attach one end of the oil pressure line to the swivel fitting (located far side) by pushing the end of the tubing into the hole at the end of the fitting. FYI: these fittings are quick disconnect and self-clinching. They need only to be pushed in to connect. They will not slip out unless the ferrule at the end of the fitting is pushed back away from the tubing as the tubing is pulled from the fitting. Routing: Next, route the other end of the tube up along the frame and in front of the steering head over to the fitting in the gauge body. Avoid the exhaust pipes when routing the tubing. Push the end of the tube into the gauge fitting as was done at the swivel fitting at the other end of the tube. The tubing can be removed and cut to the length required by your routing. Make sure there is enough service loop remaining so

TVS TANK VENT SCRUBBER INSTALLATION, OPERATION And MAINTENANCE MANUAL

0

Filed Under (TVS) by admin on 27-10-2010

download
INSTALLATION 2.1 Initial Setup After receiving the TVS, remove the packaging materials. Remove the wooden skid secured to the base of the unit and inspect all parts for damage. If any parts are damaged contact shipping company to file claim for damaged equipment. Select a location for the unit where adequate service clearance is provided for replacing the media in the unit. The media is removable from either the top, or the 150 mm port located on the side of the unit. Ample clearance (about 0.5 meters) should also be provided for space for media removal by vacuum. (This may be provided by others). 2.2 Electrical Connections (Optional) An electrical wiring diagram may be necessary and included with these instructions. 230/460 volt, 3 phase systems require a motor starter and disconnect. Refer to the wiring diagram for proper wiring connections. Check for proper motor rotation before operating the unit. All external wiring must be in accordance with National and Local Electrical Codes. Pay particular attention to proper grounding of the unit. 2.3 Media Bed Fill the Tank Vent Scrubber as follows: NOTE: Gloves and a dust mask should be worn when handling media. See MSDS sheet for proper handling requirements. 2.3.1 Remove the cover by loosening the bolts on top of the unit. 2.3.2 Inspect the interior of the tank to be certain it is empty. 2.3.3 Close and secure vacuum discharge port. 2.3.4 Select the correct media type and load the tank to a depth of 610 mm. 2.3.5 Replace the cover by securing the bolts on top of the unit. After 48 to 72 hours of operation, open cover and check media level for settlement. Media level must be 152 mm below lip of tank to reach proper fill requirement. Add media as required

Incoming search terms:

Incoming search terms: