no compression on my rear 77 iron head harley cylinder

You search Auto repair manual PDF no compression on my rear 77 iron head harley cylinder, if there are search results will appear below. If search results do not exist, please search by others keyword.



  no compression on my rear 77 iron head harley cylinder Direct Download speed 5282 Kb/s

  no compression on my rear 77 iron head harley cylinder Full Version speed 6162 Kb/s



Harley-Davidson V-Rod Destroyer Indy Series Exhaust REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
STOCK EXHAUST SYSTEM REMOVAL (DESTROYER) 1. Remove both collector bolts. 2. Remove nuts from both front and rear exhaust cylinder head flanges using a 13mm socket. 3. If the Racepak is installed, remove both O2 and EGT sensors from the front and rear head pipes. 4. Carefully remove complete exhaust from the motorcycle. STOCK EXHAUST SYSTEM REMOVAL (V-ROD) 5. Loosen clamp bolt at front of the collector using a 13mm socket. 6. Remove muffler bracket bolt using a 13mm wrench. 7. Carefully remove muffler and collector assembly from motorcycle. 8. Remove nuts from both front and rear exhaust cylinder head flanges using a 13mm socket. 9. Carefully remove head pipes from motorcycle. 10. Remove the stock exhaust flanges and circlips from both the front and rear head pipes. If the circlips are bent or twisted they should be replaced, Harley-Davidson part number #65045-01 We also recommend replacing the stock exhaust gaskets, Harley-Davidson part number #65109-01 INDY SERIES EXHAUST SYSTEM INSTALLATION 1. Identify front head pipe #7-8002. Install the stock flange and circlip. Install the exhaust gasket and front header pipe, leaving the flange nuts hand tight. 2. Repeat the above step for the rear head pipe #7-8006. 3. Slip the megaphone/collector assembly onto the head pipes, secure with the four springs supplied using the spring puller tool. 4. Rotate the exhaust so there is adequate clearance in all places. 5. Tighten the cylinder head flange nuts for both the front and rear head pipes. 6. Tighten both the EGT and O2 plugs on the front and rear head pipes. 7. Clean all fingerprints from the exhaust using a contact cleaner (or other non flammable cleaner). Fingerprints will leave stains on the pipe once the motorcycle is started. 8. You are now ready to start the motorcycle.

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

HARLEY DAVIDSON AUTOMATIC COMPRESSION RELEASE TOOLS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
INSTALLATION Compressed air can pierce the skin and flying debris from compressed air could cause serious eye injury. Wear safety glasses when working with compressed air. Never use your hand to check for air leaks or to determine air flow rates. (00061a) Wear safety glasses or goggles while drilling. Flying debris could result in serious eye injury. (00565b) 4 3 6 5 6 1 2 7 is05443 1. Drill, 1.250 inch 2. Drill stop collar, 1.250 inch 3. Drill stop gauge 4. Socket head screw, 5/16 inch 5. Socket head screw, 1/4 inch 6. Dowel pin 7. Top plate Figure 1. Top Plate and Drill Bit Stop Collar Installation 1. Remove valves from cylinder heads. NOTE Do not allow the threaded studs to damage the gasket sealing surface of the cylinder head. 2. See Figure 7 and Table 1. Mount a cylinder head to the tooling plate (1). 3. Place a head bolt spacer (7) over each stock head bolt and lubricate threads and thrust faces, dowels and studs. Tighten head bolts in a crisscross pattern to 10 ft-lbs (13.5 Nm) . 4. See Figure 1. Align the top plate (7) bolt and dowel holes with the head hole pattern, Screamin’ Eagle logo towards the spark plug. This plate will only fit one way for the cylinder head it is being installed on. If the plate does not align with the head, turn it over keeping the logo towards the spark plug and install the cylinder head. 5. Lubricate the two dowel pins (6) and insert in the top plate and into the cylinder head. 6. Apply lubricant to the two socket head screws (4 and 5). Insert into their respective holes in the plate to the cylinder head and tighten to 5 ft-lbs (6.8 Nm)

Incoming search terms:

Harley davidson Sportster Custom Straightshot Exhaust System REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove the nut that mounts the front muffler to the engine, located below the rear brake master cylinder. 4. Remove the bolt that mounts the rear muffler to the mounting bar. 5. Remove the entire exhaust system and set it aside. 6. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips . INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Vance and Hines recommends you replace your exhaust gaskets with Sceamin’ Eagle gaskets part number 17048-98. 2. Install the circlips and flanges from the stock system on to both of the new head pipes. 3. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the front head pipe using the stock nuts, do not tighten at this time. 5. Install the rear head pipe using the stock nuts, do not tighten at this time. 6. Install one muffler clamp (supplied) over the inlet (notched end) of each muffler. 7. Identify the front and rear muffler mounting brackets. The front bracket is stamped with the number 305 and the rear muffler bracket is stamped 213 . 8. Install the front muffler mounting bracket to the stud on the engine (where the stock muffler mounted) and fasten using the stock nut (leave loose at this time). The bracket will bend inward towards the center of the motorcycle when installed correctly. Note: You may need to move the wires and hoses on the lower frame rail to decrease the possibility of them chaffing on the bracket bolts. 9. Slip one of the mufflers onto the front head pipe. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the muffler to the mounting bracket using the 5/16″ flange head bolts (supplied) leave them loose at this time. 10. Attach the rear mounting bracket to the rear muffler. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the bracket to the muffler using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note: The single hole in the bracket will point downward and slightly forward when installed correctly

Indian Rocker Arm End Play Rear Cylinder/ Front Cylinder Installation

0

Filed Under (Indian) by admin on 12-11-2010

download
Rear Cylinder 1Rotate the engine so that the rear piston is at Top Dead Center (TDC), compression stroke, so no load is on the valves. 2Using a 3/16″ allen wrench, remove the four screws securing the rear cylinder rocker cover. 3Remove the cover and inspect both O-ring seals. Discard if damaged or worn. 4Push both rocker arms towards the valve end support bracket (A) and using a feeler gauge check the gap between the rocker arms and the pushrod end support bracket (B). NOTE: The Rocker arm end play specification should be between 0.003″ to 0.012″. 5 Compare the measurement to the specification an determine whether adjustment is necessary. If the end play is within specification, adjustment will not be required. Refit the rocker cover (instructions 14 to 15) and carry out the same inspection on the front cylinder . If the measurement is outside the specification, adjustment will be required and shimming will be necessary (follow the remainder of these instructions). Adjustment 6Using a 1/4″ allen wrench remove the 4 screws securing the rocker shaft assembly.Refit the LH support bracket and reposition the complete assembly on the rocker base. Make sure that the three dowels are in place and the slots in the rocker shafts are properly aligned with the mounting screw holes in the RH support bracket. 11Clean the threads of the 4 support bracket screws and apply Blue Loctite to the first 4 threads. 12Fit the 1-3/4″ screws into the LH support bracket (A) and the 2″ screws to the RH bracket (B). Torque all screws in cross pattern to 16-20 foot-pounds. CAUTION: The rear piston must be at TDC, compression stroke, when tightening the support bracket screws. 13Re-check the rocker end play to ensure it is within specifica- tion. 13Lubricate the two O-rings with clean engine oil and refit them in the grooves in the rocker base. 14Refit the rocker cover.

CYLINDER HEAD REPAIR MANUAL

0

Filed Under (Tips and Review) by admin on 28-10-2010

download
ADJUSTABLE CYLINDER HEAD STAND Head can be rotated 360 degrees. Stays in any position using a simple locking mechanism. Use on twin or four cylinder heads. Shipping weight: 14 lbs. Adjustable length-10-1/2″ to 20-1/2″ long x 14″ width x 10-3/4″ high. 35-8602 Cylinder Head Stand VALVE GUIDE DRIVERS Use for removal and installation of valve guides into cylinder head. Available in the following sizes: 35-8418 4.5mm YM-4116 35-8416 6mm YM-4064-A 35-8417 5mm YM-4097 35-8414 7mm YM-1225-A 35-8408 5.5mm YM-1122 35-8413 8mm YM-1200 VALVE GUIDE DRIVER SET (REMOVE & REPLACE) Designed for speed and accuracy, this eleven piece set provides the right tool for the job. Driver set includes two valve guide drivers (5.5mm and 6.6mm), four valve guide installers, one cutter, three cutter pilots (5.5mm, 6.6mm, and 7.7mm) and one tap handle extension bar. 35-9445 Valve Guide Driver Set YAMAHA VALVE GUIDE INSTALLERS These installers are used for installation of Yamaha shoulder less valve guides to a specific depth into the cylinder head. To use, position onto the valve guide and drive into the cylinder head until installer makes contact with cylinder head surface. Note: Must use with Valve Guide Driver. Available in the following sizes: 35-8439 4.5mm YM-4117 35-8437 5.0mm YM-4098 35-8419 5.5mm YM-4015 35-8435 6mm YM-4065-A 35-8423 7mm YM-4017 VALVE GUIDE REAMERS Reaming valve guides after installation assures a proper valve stem to valve guide fit. Available in the following sizes: 35-3829 4.5mm YM-4118 35-3851 7mm YM-1227 35-3836 5.5mm YM-1196 35-3852 8mm YM-1211 35-3847 6mm YM-4066 CLOVER VALVE LAPPING COMPOUND KIT The world famous green can with the four leaf clover. For seating valves, mating gears, and sharpening. Sold as a kit with coarse 120 grit (roughing) and 280 fine grit (finishing). 35-0309 Clover Valve Lapping Compound VALVE LAPPING TOOL The ultimate vacuum stick for insuring perfect surfaces on valves and valve seats. Interchangeable cups make unit suitable for use with virtually any size valve. Set includes vacuum stick, 3/4″ and 1/4″ diameter rubber cups. 35-8998 Valve Lapping Too

Incoming search terms:

YAMAHA VIRAGO 700/ 1100 2 into 2 EXHAUST SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the slip joint clamp on the front and rear head pipe, which are located at the muffler box. 2. Remove the two nuts that hold the front head pipe to the engine. Slip the head pipe out of the muffler box and set it aside. Note: Do not remove the rear head pipe, it has been incorporated in the design of the new exhaust system. 3. Remove the muffler box mounting bolt located in front of the passenger foot rest on the left side. 4. Remove two bolts from the right passenger foot rest assembly and set the foot rest aside. 5. Slide the muffler box off of the rear head pipe and set it aside. 6. Replace the muffler box mounting bolt (from step #3) using the washer and nut (supplied) on the back side. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Attach the mounting bar to the motorcycle frame behind the right passenger foot rest. Align the two holes in the largest bracket on the mounting bar with the two holes on the frame, be sure the bend in the mounting bar is pointing to the center of the motorcycle. 2. Install the round steel spacer (supplied) to the rear most hole in the bracket. 3. Attach the foot rest using the two 8mm x 1.25 x 25mm bolts (supplied). 4. Slide the new exhaust flange (supplied) onto the front head pipe. 5. Install the two heat shields to the front head pipe using the four hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the heat shields onto the front head pipe. Note: Be sure the bend in the heat shield matches the bend in the head pipe exactly. Wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 6. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 7. Slide a chrome pinch clamp (supplied) onto the expanded end of the new rear head pipe. Install a 3/8″ x 1″ bolt with a flat washer on either side of the clamp followed by a lock nut (hardware supplied). Repeat this step on the inlet end of each muffler using the two muffler clamps with 5/16″ x 1 1/4″ bolts (hardware supplied) but leave the clamp loose at this time. 8. Slip the new rear head pipe with the heat shield attached, over the stock rear pipe and gasket, but leave the clamp loose at this time. 9. Install the front head pipe, with the heat shield attached and stock gasket in place, to the front cylinder using the stock nuts, leave them loose at this time

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE MECHANICAL COMPRESSION RELEASE FIX- TURE

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
DRILLING AND TAPPING PROCEDURE Wear safety glasses or goggles while drilling. Flying debris could result in serious eye injury. (00565b) NOTE Perform the following procedure on both the front and rear cylinder heads. Tool Setup NOTE Due to slight manufacturing differences, it may be necessary to tap the fixture into place with a rubber mallet. Do NOT use excessive force. 1. Align the fixture’s locating pins with the 3/8 inch tooling holes in the head and install the fixture on the head. 2. See Figure 1 and Figure 6. Secure the fixture (1) to the head with two 5/16-18 socket head cap screws (2) and washers (9) included in the kit. Install the screws in the holes marked “F” when modifying the front head or in the holes marked “R” when modifying the rear head. Tighten screws to 80 in-lbs (9 Nm) . 3. See Figure 3 and Figure 6. Install the drill bushing (3) in the bore marked “FRONT” when modifying the front head or in the bore marked “REAR” when modifying the rear head. 4. Tighten drill bushing set screw to 50 in-lbs (5.6 Nm) . 5. See Figure 2 and Figure 6. Install collar stop (4) onto the 1/2 inch diameter shank of the step drill bit (5). Secure the collar stop with the set screw 3.900 inches (9.90 cm) from the beginning of the 3/4 inch diameter step of the drill bi

HARLEY DAVIDSON DYNA LongShot Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove both front and rear head pipe clamp bolts. 4. Remove the entire exhaust system and set it aside. 5. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips. 6. Remove the rear head pipe clamp bracket from the transmission cover. Save the bolts, two will be reused. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Locate the muffler mounting bracket (stamped 239). Mount the bracket to the engine case, to the rear of the transmission cover using the two stock bolts. Refer to figure 1. Tighten the bolts at this time. Install the mounting bar (supplied) to the transmission housing using the stock hardware. Refer to figure 1 . Note: The mounting bracket should mount flatagainst the transmission housing. Some motorcycles use a stud to mount the stock rear head pipe clamp, be sure to remove the stud from the transmission housing and replace it when mounting the bracket, this will insure that the bracket is flat against the housing. 2. Locate the muffler clamp bracket (stamped 240). Install the bracket to the outside of bracket 239, using the 5/16″x 1 1/4″ bolt and 5/16″ flat washer (supplied). Refer to figure 1. Leave the bracket loose, it will be adjusted later. 3. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the circlips and flanges from the stock system onto both the new head pipes. 5. Slide the new pipe clamp (supplied) onto the muffler end of the front head pipe. Position the clamp in the approximate mounting location on the pipe. 6. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the rear head pipe.

Incoming search terms: