open pipes for klx150 davao

You search Auto repair manual PDF open pipes for klx150 davao, if there are search results will appear below. If search results do not exist, please search by others keyword.



  open pipes for klx150 davao Direct Download speed 5282 Kb/s

  open pipes for klx150 davao Full Version speed 6162 Kb/s



Kawasaki 2000- ZX-12R Ninja exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the lower fairing. Remove the lower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1, 2, 3, and 4 by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. Place a billet aluminum Mouthpiece ring Z on each TiForce head pipe. (see figure 3 for details) . 6. Attach the assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the head pipes fit flush and snug in the ports and Mouthpiece ring Z before tightening. 7. Install the S-Bend to the front section of the head pipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications – make sure the head pipes and Mouthpiece ring Z are centered in each port. 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. (See figure 1) . 11. Place the bands approximately 118 mm from the edge of the end can. (See figure 2) . 12. Using the stock provided mounting point on the passenger foot peg, and using the stock-mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the head pipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance

Kawasaki ZRX-1100 / 1200 exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 2. Inspect the exhaust gaskets. Replace if necessary. 3. Attach the head pipes 1, 2, 3 , and 4 to the exhaust ports of their respective cylinders, using the flange nuts saved from step 1 above. Loosely apply the flange nuts for now, allowing for ome adjustment. 4. Attach the Y-pipe collectors to the head pipes. Please note that one collector goes to pipes #1 and #4 and one collector goes to pipes #2 and #3 (collectors are labeled). Make sure the ends of the head pipes fit flush and snug in the ports. Do not install the springs at this time. 5. Install the S-Bend to the rear of the two Y-pipe collectors. Do not install the springs at this time. 6. Go back and retighten the head pipe flange nuts per factory specifications – make sure the head pipes are centered in each port. 7. Slide the TiForce end can into place on the S-bend pipe. 8. Loosely attach the two rubber bands, stainless steel bands K, and the stay / hanger G, to the end can using the supplied 6mm hardware H. (See figure 1) . Make sure that the rubber bands fully cover the stainless bands to prevent scratches to the can. 9. Place the bands approximately 108mm from the edge of the end can. (See figure 2) . 10. Go back and tighten the exhaust flange nuts per factory specification. Do not over tighten. 11. Using the stock provided mounting point on the right passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to all the joints, starting from the head pipes and working back to the end can. 13. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 / figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 16. Check that all hardware is properly tightened, and then start the motor and check for exhaust leaks

Incoming search terms:

2007 – 2009 KAWASAKI Z 1000 RACING AND EVOLUTION EXHAUST SYSTEM

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
The Akrapovic RACING OPEN & EVOLUTION OPEN line is the highest level of Akrapovic exhaust systems and with hexagonal shaped muffler fits perfectly with the aggressive character of the ‘Z’. The conical tubing with interference crossover tubes between the header tubes work exceptionally well. With the Akrapovic exhaust system you will get massive power boost, more torque, a sportier sound and an even more aggressive top- level look on this muscular roadster. You can choose between classy titanium or carbon- fiber mufflers that stand out through their excellent quality. The systems are available in open version only. Besides great power and torque, you will also save in overall weight, as the Akrapovic system weighs 10.21 kg (RACING) or 11.5 kg (EVOLUTION) less than the stock assembly. PERFORMANCE Measurements of the Akrapovic RACING OPEN & EVOLUTION OPEN system on the Ka- wasaki Z 1000: The power curve shows a huge increase over the stock performance figures. It is much more linear, which means the engine is pulling strong and consistently right from the lowest rpm to the highest part of the overrev range. We measured a maximum increased power of 10.0 HP at 10270 rpm. The same goes for torque, which is also increased through entire rpm range. The drop-outs in the stock curve are filled and like the power curve, there is a major increase from 4000 rpm on. CONFIGURATION The configuration of the Akrapovic RACING OPEN & EVOLUTION OPEN system for the Z 1000 is 4-2-1, made of conical stainless steel or titanium tubes. The system includes interference crossover tubes between the header tubes, giving the Kawasaki increased performance characteristics. The muffler is available with either a titanium or carbon-fiber outer sleeve, attached to the motorcycle with an Akrapovic carbon-fiber muffler clamp. The individual elements of the system – header tubes, collector, link pipe and muffler – are connected with sleeve joints, secured with silicon-shielded springs.

2004 Honda CRF450R OWNER'S MANUAL

0

Filed Under (Honda) by admin on 21-11-2010

download
motorcycle can be kickstarted with the transmission in gear by disengaging the clutch before operating the kickstarter. Check the engine oil, transmission oil and coolant levels before starting the engine (page 21, 23, 24). Cold Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. If the temperature is 35°C (95°F) or below, pull the choke knob fully out. 4. If the temperature is below 0°C (32°F), open the throttle two or three times. (The engine requires a richer mixture for starting in cold weather. When the throttle is so opened, the accelerator pump will feed extra fuel to the cylinder, thereby facilitating starting in cold weather.) 5. With the throttle closed, operate the kickstarter starting from the top of the kickstarter stroke, kick through to the bottom with a rapid, continuous motion. (Do not open the throttle, As the carburetor is equipped with an accelerator pump, excessive fuel will be charged into the engine, and the spark plug will be fouled if the throttle is opened and closed repeatedly. Excessive fuel in the engine makes kick- starting difficult.) 6. About a minute after the engine starts, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. (1) FUEL FILL CAP (2) BREATHER TUBE WARNING (1) FUEL VALVE (2) CHOKE KNOB Warm Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever 1. Shift the transmission into neutral. 2. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 3. As soon as the engine starts, release the hot start lever. Starting the engine excessively charged with fuel by throttle blipping or other reasons: 1. Shift the transmission into neutral. 2. With the throttle fully opened, repeat kickstarter operation approximately 10 times very slowly to discharge excessive fuel from the engine. 3. Pull the hot start lever and kick-start the engine (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever. Stopping The Engine 1. Shift the transmission into neutral. 2. Turn the fuel valve OFF. 3. Lightly open the throttle 2 – 3 times, and then close it. 4. Depress and hold the engine stop button until the engine stops completely. NOTE: • Failure to close the fuel valve may cause the carburetor to overflow. (1) THROTTLE GRIP (2) ENGINE STOP BUTTON Break-In Procedure Help assure your CRF’s future reliability and performance by paying extra attention to how you ride during the first operating day or 15 miles (25 km). During this period, avoid full-throttle starts and rapid acceleration. This same procedure should be followed each time when: • Piston is replaced • Rings are replaced • Cylinder is replaced • Crankshaft or crank bearing are replaced

Incoming search terms:

Harley-Davidson V-Rod Destroyer Indy Series Exhaust REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
STOCK EXHAUST SYSTEM REMOVAL (DESTROYER) 1. Remove both collector bolts. 2. Remove nuts from both front and rear exhaust cylinder head flanges using a 13mm socket. 3. If the Racepak is installed, remove both O2 and EGT sensors from the front and rear head pipes. 4. Carefully remove complete exhaust from the motorcycle. STOCK EXHAUST SYSTEM REMOVAL (V-ROD) 5. Loosen clamp bolt at front of the collector using a 13mm socket. 6. Remove muffler bracket bolt using a 13mm wrench. 7. Carefully remove muffler and collector assembly from motorcycle. 8. Remove nuts from both front and rear exhaust cylinder head flanges using a 13mm socket. 9. Carefully remove head pipes from motorcycle. 10. Remove the stock exhaust flanges and circlips from both the front and rear head pipes. If the circlips are bent or twisted they should be replaced, Harley-Davidson part number #65045-01 We also recommend replacing the stock exhaust gaskets, Harley-Davidson part number #65109-01 INDY SERIES EXHAUST SYSTEM INSTALLATION 1. Identify front head pipe #7-8002. Install the stock flange and circlip. Install the exhaust gasket and front header pipe, leaving the flange nuts hand tight. 2. Repeat the above step for the rear head pipe #7-8006. 3. Slip the megaphone/collector assembly onto the head pipes, secure with the four springs supplied using the spring puller tool. 4. Rotate the exhaust so there is adequate clearance in all places. 5. Tighten the cylinder head flange nuts for both the front and rear head pipes. 6. Tighten both the EGT and O2 plugs on the front and rear head pipes. 7. Clean all fingerprints from the exhaust using a contact cleaner (or other non flammable cleaner). Fingerprints will leave stains on the pipe once the motorcycle is started. 8. You are now ready to start the motorcycle.

Incoming search terms:

2008 Harley Davidson Softail Deluxe Exhaust Installation Supplement to Installation Manua

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1. Install LH and RH passenger foot peg mount using 3/8×2-1/4″ hex head bolts, 3/8″ SAE flat washers, 3/8″ lock was and 1″ spacers between the motorcycl frame and mount. Figure 1 hers e xhaust ter) n’t Cut 6-1/4″ from end Cut 1/2″ from end Figure 2 2. Remove exhaust chrome covers from header pipes. 3. It is not necessary to remove the front cylinder’s front cover. Remove header pipes from cylinder heads. Cut pipes as shown in Figure 2. 4. Replace header pipes Cut cover 5-5/8″ from end – Shown already cut Figure 3 5. Cut top cover as shown in Figure 3. 6. Install supplied extension pipes as shown in Figure 3 using the OE e clamps. (Clamps covered by covers in picture – covers will be installed la Rotate clamps to make sure they don’t interfere with the foot peg mounts. Do tighten clamps yet. 7. Mount exhaust hanger bracket to body frame with (3) supplied vibration mounts. Figure 4. Figure 4 8. Install supplied clamps to ends of mufflers and fit over exhaust extensions. 9. Attach exhaust pipes to hanger bracket with OEM hardware (4 bolts). Apply Red Loctite to OEM bolts. Figure 4. 10. Install all chrome covers 11. Tighten all exhaust clamps. Figure 5 12. Install supplied chrome cover with clamp removed from cut OE chrome cover. Supplied cover slips over OE chrome cover. Push cover forward to prevent the body from hitting the cover. Figure 5. 13. Move OE clamp backwards and install 14. Position luggage rack as shown in figure 5. Install luggage rack with OE bolt in the Figure 6 Bracket OE Bolt Clamp Figure 7 Drill ¼” holes bracket using OE bolt and supplied 3/8″ bolt. Figure 6. 7 and drill two ¼” holes in shock tower mount. 1 rear and the supplied ¼” bolts in the front.

DUCATI MONSTER S4R And DUCATI MONSTER S2R EXHAUST SYSTEM Installation instructions

0

Filed Under (Ducati) by admin on 26-10-2010

download
REMOVAL OF STOCK EXHAUST SYSTEM: 1. Put the motorcycle on a side stand, we recommend a racing stand. Make sure, that surface is solid and flat. 2. Remove stock heat shields (Figure 1, 2) 3. Unscrew the bolts from the metal clamps at the muffler – collector joints (Figure 3, 4). T-handle 10mm wrench T-handle 12mm wrench T-handle 13mm wrench T-handle 3mm three hexagon key wrench T-handle 5mm three hexagon key wrench Combination 13mm wrench Spring puller Figure 1 Figure 2 Figure 3 Figure 4
NAV – 124 3 Figure 10 Figure 7 Figure 8 4. Unscrew the bolt from the muffler chassis hanging bracket and remove both mufflers with link pipes (Figure 5, 6). INSTALLATION OF THE AKRAPOVIC SLIP-ON EXHAUST SYSTEM: 1. Slide the link pipes onto the stock collector (Figure 7) hand tighten the metal clamps at the Akrapovic link pipe – stock collector joints; coat the interior side of the metal clamps and the clamp bolts with Akrapovic anti-seizing copper paste (black tube) (Figure 8). 2. Install Akrapovic carbon-fiber chassis hanging bracket (Figure 9, 10). 22Nm 16ftlb Figure 5 Figure 6 Figure 9 NAV – 124 4 Figure 15 3. Position the muffler correctly and slide it onto the outlet side of the link pipes and attach the springs; WARNING! make sure, that springs pull the muffler all the way onto the link pipes – use rubber mallet if necessary to tap the connections into place! (Figure 11, 12). 4. Correctly position the carbon-fiber clamp and slide it onto the muffler – bear in mind the left offset of the carbon-fiber clamp viewed from the rear. WARNING: open the clamp slightly wider than the diameter of the outer sleeve of the muffler – do not scrape it along the muffler outer sleeve! (Figure 13). Tighten the carbon-fiber clamp onto the Akrapovic carbon- fiber chassis hanging bracket (Figure 14, 15). Make sure the link pipes or muffler are not touching the frame or any other part of the motorcycle.

Incoming search terms:

HONDA VF750 MAGNA SLIP-ON EXHAUST SYSTEM Installation Manual

0

Filed Under (Honda) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the left and right side frame covers to prevent damaging them. 2. Loosen the pinch clamps on the inlet end of all four mufflers, located behind the rear motor mount. 3. Remove the left and right front head pipes. 4. Remove the rear mounting bolt from both muffler assemblies. Carefully slide each muffler assembly off the head pipes and set them aside. 5. Replace the front head pipes. Note : Leave the head pipes loose for later adjustment. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 2. Place the slip-on head tube into the matching heat shield, wrap the hose clamp around the head tube and give the screw three to four turns, leaving heat shield loose on the head tube. Repeat this step with opposite head tube and heat shield. 3. Slide a T-bolt band clamp (supplied) onto the slotted end of each slip-on tube. 4. Slip the slotted end of tube onto the rear head pipes. The shorter of the two slip-on tubes mounts on the right rear head pipe and the longer tube on the left rear head pipe. Tighten the T- bolt clamp until the pipe is snug but so the pipe will still be able to rotate. 5. Install the muffler mounting brackets to the frame using the single hole in the brackets and the stock hardware. The left side mounting bracket (stamped #206 on the bracket) mounts to the outside of the frame, where the stock muffler assembly mounted. The right side bracket (stamped #207) mounts to the inside of the frame, behind the stock muffler mounting point. 6. Slide a chrome muffler clamp (supplied) onto the inlet end of each muffler. Install a 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by a lock nut (all supplied). Do this to each muffler but leave the clamp loose at this time. 7. To determine the difference between the left, right, upper and lower mufflers refer to the number stamped on the bracket welded to the backside of each muffler. The top right hand muffler is D500, the bottom right hand muffler is D510, the top left hand muffler is D550 and the bottom left hand muffler is D512. Note : The endcap bolts should face down and inward when viewing from the rear (Refer to Figure 1) .

Kawasaki Vulcan 400/ 800 Preload Improvement Kit Installation Instructions

0

Filed Under (Kawasaki) by admin on 01-12-2010

download
1. Begin by removing both side compartment covers. The RH compartment cover requires the use of the ignition key for removal; the LH compartment cover is secured by a large Phillips screw. Once you’ve removed the LH cover, place the Phillips screw back into the hole in the frame (so you don’t misplace it) and set both covers aside. In many applications, you must remove the upper exhaust pipe (from the rear cylinder), and loosen the other pipe, to remove the inner parts of the RH side compartment cover (see below). Before attempting step #2 below, try step #3 first… depending on the brand of exhaust pipes you have, you may be able to avoid removal in step #2, if you are successful with step #3 first. Some brands of exhaust pipes provide access to the fasteners securing the RH side covers, eliminating the requirement to remove pipes for rear suspension access. 2. Remove the rear cylinder’s exhaust pipe. To do so, remove the two Allen nuts on the exhaust header, where it attaches to the engine, using an 8mm Allen wrench. Most often, this goes much more smoothly if you first spray the inside of the allen nut with a penetrating lubricant like WD-40. Remove the black acorn nut from the discharge end of the exhaust pipe (under the upper exhaust pipe, near the discharge end of the pipe) using a 12mm open-end wrench or socket. You’ll find a black metal spacer, through which the bolt goes, that is pressed through the rubber grommet. To avoid the potential of having it fall out unnoticed, remove it and place it aside with the nut. Remove the black bolt from the pipe just aft (to the rear) of where the pipe enlarges and above the pipe. This is actually a bracket that holds the two pipes together at a joint. Loosen the bolt using a 12mm socket, then slide it back onto the pipe you’re removing. Once you have the pipe off of the bike, the clamp will be loose. Be sure to keep it with the pipe, along with the rest of the removed parts. Loosen the pipe from the front cylinder BEFORE trying to remove the pipe from the rear cylinder. By loosening the header nuts on the pipe from the front cylinder, and removing the two black Allen bolts (6mm Allen wrench) under the forward pipe that attach it to the frame, you will be able to remove the rear pipe. There are more spacers in grommets where the 6mm Allen bolts secure the lower pipe to the frame (like those used in the rearmost connection o

Incoming search terms:

HARLEY DAVIDSON SPORTSTER BLACK EXHAUST HEAT SHIELDS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
INSTALLATION Remove Original Equipment (OE) Heat Shields Avoid contact with exhaust system and wear protective clothing that completely covers legs while riding. Exhaust pipes and mufflers get very hot when engine is running and remain too hot to touch, even after engine is turned off. Failure to wear protective clothing could result in burns or other serious injury. (00009a) 1. Allow the motorcycle to cool. 2. Identify the position of the OE clamp screws securing the black heat shields to the exhaust pipes. NOTE The clamp screws are positioned on either side of the exhaust pipe for clearance. 3. See Figure 1. Open the heat shield clamps (1) and spread the bands to remove front and rear heat shields (2) from the exhausts. Retain the heat shield clamps Install Black Heat Shields 1. See Figure 2. Matching the OE position of the heat shield clamps, open the clamps bands and thread the bands through the brackets of the front (1) and rear (2) black heat shields. 2. Spread the band around the exhaust pipes and push the end of the bands to engage the clamp screws. Tighten to hold the heat shields in place. 3. Adjust the shields and heat shield clamps to access clamp screws and to avoid contact with other components. 4. Tighten the heat shield clamp screws

Incoming search terms: