owners manual for a tk 52 007 tank motorcycle

You search Auto repair manual PDF owners manual for a tk 52 007 tank motorcycle, if there are search results will appear below. If search results do not exist, please search by others keyword.



  owners manual for a tk 52 007 tank motorcycle Direct Download speed 5282 Kb/s

  owners manual for a tk 52 007 tank motorcycle Full Version speed 6162 Kb/s



HARLEY DAVIDSON CHROME FUEL TANK TRIM PANEL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
INSTALLATION 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat. Retain all seat mounting hard- ware. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) 2. See the Figure 5. Remove the original fuel filler cap (A) from the tank and set it aside. Obtain a small diameter Harley-Davidson fuel filler cap (B) and screw it into the fuel filler opening. For Model XL883C, or other models equipped with Genuine Motor Parts Large Capacity Fuel Tank 3. To ensure surface cleanliness, clean the top of the fuel tank with a mixture of 50 to 70% isopropyl alcohol and 30 to 50% distilled water. Allow to dry thoroughly. 4. Measure and mark the centerline of the fuel tank, with a wax pencil or water-based marker, at the rear of the tank as shown in Figure 3. Proceed to Step 10. For Model XL1200C 2 1 is 01910 1. Original fuel tank trim panel liner 2. Fishing line (or string) Figure 1. Removing the Existing Trim Panel (XL 1200C) 5. See Figure 1. Insert the fishing line (2) between the rear of the fuel tank and the liner (1) on the underside of the original trim panel. NOTE Raise the ends of the fishing line away from the fuel tank to avoid scuffing the tank finish 6. Using a side-to-side “sawing” motion, work the fishing line toward the front of the fuel tank to break the adhesive bond between the trim panel and the tank. 7. Carefully pull the trim panel and liner off of the tank and discard it. NOTE Be careful not to scratch the paint on the fuel tank when removing the adhesive

Incoming search terms:

Honda CG125 Owners Manual, and repair manual

0

Filed Under (Honda) by admin on 11-12-2011

download
The author of this manual has the conviction that the only way in which a meaningful and easy to follow text can be
written is first to do the work himself, under conditions similar to those found in the average household. As a result, the hands seen in the photographs are those of the author. Even the machines are not new: examples that have covered a consider- able mileage were selected so that the conditions encountered would be typical of those found by the average owner. Unless specially mentioned, and therefore considered essential, Honda service tools have not been used. There is
invariably some alternative means of slackening or removing some vital component when service tools are not available and
isk of damage has to be avoided at all costs. Each of the six Chapters is divided into numbered Sections. Within the Sections are numbered paragraphs. In consequence, cross reference throughout this manual is both straightforward
and logical. When a reference is made ‘See Section 5.12′ it means Section 5, paragraph 12 in the same Chapter. If another
Chapter were meant, the text would read ‘See Chapter 2, Section 5.12′. All photographs are captioned with a Section/paragraph number to which they refer and are always relevant to the Chapter text adjacent. Figure numbers (usually line illustrations) appear in numerical order, within a given Chapter. Fig. 1.1 therefore refers o the first figure in Chapter 1. Left-hand and right-hand descriptions of the machines and their component parts refer to the right and left of a given machine when the rider is seated normally. Motorcycle manufacturers continually make changes to specifications and recommendations, and these, when notified,mare incorporated into our manuals at the earliest opportunity.
We take great pride in the accuracy of information given in this manual, but motorcycle manufacturers make alterations and design changes during the production run of a particular n motorcycle of which they do not inform us. No liability can be ccepted by the authors or publishers for loss, damage or injury caused by any errors in, or omissions from, the information give

Incoming search terms:

HONDA CBX 750F OWNERS MANUAL AND REPAIR MANUAL

0

Filed Under (Honda) by admin on 02-12-2011

download
Always make a pre-ride inspection before you start the engine. You may prevent an accident or equipment damage. 2 Many accidents involve inexperienced riders. Most countries require a special riding test or license. Make sure you are qualified before you ride. NEVER lend your motorcycle to an inexperienced rider. 3 Many car/motorcycle accidents happen because the car driver does not “ see the motorcyclist. Make yourself conspicuous to help avoid the accident that is not your fault: • Wear bright or reflective clothing • Don’t drive in another motorist’s “blind spot” 4 Obey all national, and local laws and regulations Excessive speed is a factor in many accidents. Obey the speed limits am NEVER travel faster than conditions warrant • Signal before you make a turn or lane change. Your size and manoeuvrability can surprise other motorists.5 Don’t let other motorists surprise you. Use extra caution at intersections, parking entrances and exits and driveways. 6 Keep both hands on the handlebars and both feet on the footrests while riding. A passenger should hold onto the motorcycle or the rider with both hands, and keep both feet on the passenger footrests. PROTECTIVE APPAREL
1 Most motorcycle accidents fatalities are due to head impact. ALWAYS wear a helmet. You should also wear a face shield or goggles; boots, gloves, and protective clothing. A passenger needs the same protection. The exhaust system becomes very hot during operation, and it remains hot after operation. Never touch any part of the hot exhaust system. Wear clothing that fully covers your legs.
3
Do not wear loose clothing which could catch on the control levers, footrests, or wheels

2005-2007 KTM MOTORCYCLE REPAIR MANUAL

0

Filed Under (KTM) by admin on 21-11-2010

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 2 2-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B 2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork Dismounting the fork -Place your motorcycle on a stand. -Notice the position of the front fork in the triple-clamps. NOTE: To remove the front fork. Read your KTM Instruction Manual or Workshop Manual. 3-3 Mounting the fork -Clean the innerside of the triple-clamps with brake cleaner. -Slide both fork legs into the triple-clamps. NOTE: Pay attention to the position of the fork legs. Standard riding height! NOTE: The maximum riding height is the level of the second groove! -Tighten the middle bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the first bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the third bolt of the lower triple clamp to a torque of 17 Nm!

Incoming search terms:

HARLEY DAVIDSON FUEL LEVEL SENDER ADAPTER BRACKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Remove the currently installed fuel tank from the vehicle. Follow the instructions for the correct model vehicle under FUEL TANK: EFI, REMOVAL in the Service Manual. 3. See FUEL PUMP/FUEL GAUGE SENDING UNIT, REMOVAL in the Service Manual for instructions to: a. Unplug the fuel pump module connector. b. Remove and discard the top plate screws. c. Remove the top plate, fuel pump and fuel level sender (fuel gauge sending unit) from the tank. NOTE Take care to avoid bending the fuel level sender float rod. A bent float rod will lead to erroneous gauge readings. 2 6 1 3 4 7 9 8 5 is05284 1. Fuel level sender 2. Electrical grounding tab 3. Fuel level sender lock tab 4. Adapter bracket 5. Slot (2) 6. Terminal strip insert 7. Sender to adapter lock tab 8. Slider 9. Adapter to tank lock tab Figure 1. Fuel Level Sender Assembly to Adapter – 4. See Figure 1. Clean the electrical grounding tab (2) on the back of the fuel level sender if necessary. The tab must make firm contact with the terminal strip insert (6) in the adapter bracket. Slide the original equipment (O.E.) fuel level sender (1) into the slots (5) in the new adapter bracket (4) as shown until the lock tabs (3 and 7) snap into place. Make sure the wire is not pinched between the adapter and sender. 5. See FUEL SUPPLY CHECK VALVE/TUBE in the Service Manual. Remove the check valve/quick-connect fitting assembly from the old fuel tank, and assemble to the new tank, using a new O-ring (purchased separately). 6. Fit the slider (8) on the adapter bracket into the fuel level sender mounting channel inside the tank, and push down until the lock tab (9) snaps into place. Make sure the sender and adapter wires are not pinched between the adapter and the fuel tank tunnel, and remain accessible through the fuel tank top opening. 7. See Figure 2. Obtain the assembly of the top plate (1), regulator (2) and fuel filter (3) removed from the old fuel tank, and the stainless steel screw (8) and nut (9) provided in this kit.

Incoming search terms:

Yamaha XVS 13AW Owner's Manual REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 06-01-2012

download
GASOLINE IS HIGHLY FLAMMA- BLE: Always turn the engine off when refueling. Take care not to spill any gasoline on the engine or exhaust system when refueling. Never refuel while smoking or in the vicinity of an open flame. Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. Always operate your motorcycle in an area that has adequate ventilation. Always turn the engine off before leaving the motorcycle unattended and remove the key from the main switch. When parking the motorcycle, note the following: The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. Do not park the motorcycle on a slope or soft ground, otherwise it may fall over. Do not park the motorcycle near a flammable source, (e.g., a kerosene heater, or near an open flame), otherwise it could catch fire. When transporting the motorcycle in another vehicle, make sure that it is kept upright. If the motorcycle should lean over, gasoline may leak out of the fuel tank. If you should swallow any gasoline, inhale a lot of gasoline vapor, or allow gasoline to get into your eyes, see your doctor immediately. If any gasoline spills on your skin or clothing, immediately wash the affected area with soap and water and change your clothes

Incoming search terms:

BUELL ACCESSORY GAS CAP KIT INSTALLATION MANUAL

0

Filed Under (Buell) by admin on 29-03-2011

download
Installation NOTE When performing the following Steps, use the Fuel Tank Vent Valve Installation Kit (Part Number 91432-96Y). This kit consists of: * Fuel Tank Vent Valve Installation Aid * Fuel Tank Vent Valve Fitting Socket To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect battery cables, negative cable first. An open flame or spark may cause a fuel tank explosion if all traces of fuel are not purged from the tank. Use extreme caution when servicing fuel tanks. Gasoline is extremely flammable and highly explosive. Do not smoke or allow open flame or sparks anywhere in the area when working on fuel system components. Inadequate safety precautions could result in death or serious injury. 2. Remove gas cap. 3. Carbureted Models: Drain fuel tank. Disconnect hose clamp and fuel supply hose from fuel supply valve and drain fuel into suitable, clean container. See applicable Service Manual, Section 4 for complete, detailed procedure. Fuel Injected Models: Relieve pressure from fuel system. See applicable Service Manual, Section 4 for complete, detailed procedure. Drain fuel tank. a. Using suitable external fuel pump, such as a Gas Caddy, pump fuel from tank and into a suitable, clean container. b. See instructions for external fuel pump for correct use. 4. See Figure 1. Cut cable tie securing vent hose to fitting and remove vent hose from fuel tank. Even with the fuel tank completely drained, a small amount of gasoline may leak from the bore when the fuel supply valve is loosened or removed. Thoroughly wipe up any fuel immediately and dispose of rags in a suitable manner. Gasoline is extremely flammable and highly explosive. Inadequate safety precautions could result in death or serious injury. 5. If the fuel supply valve requires cleaning or repair, refer to applicable Service Manual, Section 4, for complete, detailed procedures. 6. See Figure 1. Remove the fuel filler cap and O-ring. 7. Remove the eight self-tapping screws from fuel clamp flange and remove fuel cap flange

HARLEY DAVIDSON BILLET HEADLAMP WITH SHORT/ TALL MOUNTS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Kit 68593-06 is a 5-3/4 inch headlamp and kit 69851-06 is a 4-1/2 inch headlamp. Both kits will fit the models listed in Table 1. Table 1. Short and Tall Mount Kits Models Kits 1984-1999 FXSTC, 1998- Later FXST/B, and 2000-Later FXSTD; 1994-2005 FXDWG Short Mount Kit 68595-06 1996-Later XL 1200C and 1998-Later XL 883C; All 2006 Dyna Models; 1999-2000 FXR2/3/4 Tall Mount Kit 69611-06 Additional Parts Required This kit also requires the separate purchase of a Short or Tall Mounting Kit 68595-06 or 69611-06 for your model motorcycle, and can be purchased from a Harley-Davidson dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 21, Table 2 and Figure 22, Table 3. REMOVAL Remove Headlamp and Mounting Bracket for Softail Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. 2. Remove fuel tank. Refer to FUEL TANK in Service Manual. 3. Disconnect 4-place headlamp connector [38] from main wire harness. Headlamp connector is located under fuel tank on left side. 8 5 7 5 6 2 1 3 4 is01835 1. Screw 2. Washer 3. Nut 4. Lockwasher 5. Washer (2) 6. Screw 7. Mounting block 8. Headlamp assembly Figure 1. Softail and Dyna Headlamp Assembly with Mount (except FXSTD) NOTE All Softails (except FXSTD) complete steps 4 through 6. For FXSTD models complete steps 7 through 9 4. All Softails (except FXSTD): See Figure 1. Remove screw (1) and washer (2) from stem and bracket. Discard screw but save washer for later use. 5. Remove and discard mounting block (7) and headlamp assembly (8). 6. FXSTD models: See Figure 2. Remove screw (1) and washer (2) from stem and bracket. Save screw and washer for later use. 7. Remove and discard nut (3), washers (4), and screw (5). 8. Remove and discard mounting block (6) and headlamp assembly (7). 7 3 4 2 1 4 6 5 is01838 1. Screw 2. Washer 3. Acorn nut 4. Washer (2) 5. Screw 6. Mounting block 7. Headlamp assembly Figure 2. FXSTD Headlamp Assembly with Mount Remove Headlamp and Mounting Bracket for Dyna Models 1. Remove seat following the instructions in the Service Manual. 2. Disconnect negative (-) battery cable. 3. Remove fuel tank. Refer to FUEL TANK in Service Manual. 2 1 is01750 1. Cable strap 2. Wire harness Figure 3. Dyna Service Loop (2005-Earlier) 4. 2005-Earlier FXDWG: See Figures 3 and 4. Remove plug on right side of top frame tube. At service loop, remove cable clip and push wire harness into top frame tube. Pull connector out from hole on right side of tube. 2006-Later FXD: See Figure 5. Remove cover under top frame tube, then pull connector out from opening under tube. 5. Disconnect 4-place headlamp connector [38] from main wire harness

Incoming search terms:

POLINI MINICROSS AND MlNlMOTARD OWNER'S AND MAINTENANCE MANUAL

0

Filed Under (Polini) by admin on 22-11-2010

download
Fit the stand using the M8x18 screw to fasten it and the spring provided (photo 1 6). A DANGER! We suggest you to remove the stand during competitions as it could be dangerous and bruising. 18- Fit the gear lever l~hoto 171. 19- Fill the fuel tank (See section 4.13). 20- Check the engine oil level (See section 4.3). INTRODUCTION Always ensure that the motorcycle has been efficiently serviced and check it over before riding it. Take your motorcycle to an authorised POIJNI MOTOR1 dealer for all maior servicing and repair. Because of the manufacturer’s policy OF continuous development, and because of constant innovations in technology, your motorcycle may differ in some details from that described in the illustrations and text in this manual. Original POLlNl MOTOR1 spare parts are always made from the same materials and in the same way as the parts originally fitted to your minicross motorcycle. Always insist on original POIJNI MOTOR1 spore parts. Their use ensures a longer life and improved efficiency for your motorcycle. 2. STARTING THE ENGINE FOR THE FIRST TIME Always check over your motorcycle thoroughly before starting the engine. To start the engine for the first time, as instructed below. 1 – Turn the fuel tap located under the fuel tank to #ON” position (photo 18) Run your new motorcycle in as instructed How to ensure that the engine and transmission bed in correctly and to ensure continuous reliability in Future. A CAUTION! The first time yw ride your new motorcycle, ride for about two hours at low engine speeds to ensure that it runs in correctly. Also respect the following precautions. 2- Once the engine starts, leave it idle until it warms up to normal temperature. If you switch the engine off for a short time, wait for it to cool down completely before you re-start it. – 3- During the running in period, always ride at constant 2- Before starting the engine put the gear in neutral position speeds. AVOID RAPID ACCELERATION. (photo 19, gear N). 4- Even when riding at low engine speeds, avoid extended A WARNING! IF the gear position is not neutral the bike could move when started. 3- If the engine is cold, lift the choke lever on the carburettor (photo 20). A WARNING! Lower the starter lever again as won as the engine starts to warm up. 4- Leove the throttle closed. Pivot the kick-start lever out wards and push energetically downwards with your foot to start the engine. 5- Return the kick-start lever to its rest position. Leave the engine idle for a few minutes to warm it up. A WARNING! Check that the engine stop button stops the engine effectively before yw begin riding the motorcycle. difficult sections of road or Lck that could cause the engine to become very hot. 5- Once you have run in your motorcycle following all these instructions, take it to a Polini Motori dealer for its post- running-in service. Apart from a change of spark plug and engine oil, this service also includes the disassembly

Incoming search terms:

SUZUKI GSX-R1000 SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 12-11-2010

download
Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. 5. Install the air cleaner box in reverse order of removal. (Refer to Service Manual, Page 5-14) 6. Lower the fuel tank. (Refer to Service Manual, Page 5-3) 7. Remove the upper seat rail plate. Disconnect and remove the ECM. (Figure 1) @ ISC Valve Mounting Screw Torque: 2.1± ±0.6 N.m (1.5± ±0.4 lb-ft) ! Carefully insert the ISC valve straight into the throttle body hole to prevent damaging the o-ring. Turn the ISC valve slightly to confirm that the o-ring has not twisted. Using the new screw provided in the replacement parts kit, make sure the screw is completely seated on the plate after the screw has been tightened to the specified torque. 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. ! Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) REPLACEMENT PROCEDURE: 8. Install the new ECM in reverse order of removal. Apply thread lock to the upper plate mounting bolts when reinstalling the upper seat rail plate.

Incoming search terms:

Incoming search terms: