parts breakdoqn for mikuni vacuum operated carb

You search Auto repair manual PDF parts breakdoqn for mikuni vacuum operated carb, if there are search results will appear below. If search results do not exist, please search by others keyword.



  parts breakdoqn for mikuni vacuum operated carb Direct Download speed 5282 Kb/s

  parts breakdoqn for mikuni vacuum operated carb Full Version speed 6162 Kb/s



42MM MIKUNI FLATSLIDE CARBURETOR INSTRUCTIONS

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at 1/2 to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle. The output of the OEM fuel pump is too high and will cause fuel overflow in the HSR carb, resulting in a possible dangerous fire hazard

Incoming search terms:

KAWASAKI 1500 CARB THUNDER Air Filter Kit Installation And removal Instruction

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove Seat 10mm KAW 1500 CARB ADPTOR QTY PARTS LIST 1 1500 CARB ADAPTOR 1 3″ PIECE OF HOSE 1 DOUBLE BARB 1 L-BARB 1 3/8″ RED PLUG 1 ¼” BLACK VACCUM PLUG 1 M6-1 NYLON INSERT LOCK NUT 3 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 170 MJ 1 INSTRUCTIONS 2) Remove Dash Plaque 8mm bottom Bolt only 3) Lift from bottom then Remove speedo cable 4) Disconnect Electric Plugs 5) Remove 12mm bolts holding tank 6) Turn petcock OFF – Pinch off fuel line. 7) Disconnect the electric Plug under speedo opening 8) Lift Tank at Rear – Disconnect two Vent Lines; Fuel gage Vent will Pull up – Remove. 9) Remove Chrome Air Cover. 10) Left side Remove two screws – 10mm bolt in side Air box. Pull hoses off Remove 1″ hose going to cross over Tube. 11) Remove two 8mm bolts on Bracket – Remove Bracket 12) Remove Screw on Top of air Box Snorkel 13) Remove both side covers 14) Remove air Backing plate right side (Crank Case Breather hose that connects to stock air box will connect to new) 15) Remove Bracket that holds Carb and holds Backing Plate 16) Take idle adjustable Knob loose – let hang loose 17) Take Choke Knob out of holding Bracket 18) Hose that went to cross over tube MAY BE PLUGGED OR VENTED your Choice (Fresh air unit) ** 98′S or any models with carb warmer should disconnect carb warmer by pinching off line on each side of connector that plugs into carb on bottom. Small bracket with one screw directly on the bottom of carb. 19) Loosen Clamp that holds Carb to intake Manifold, Carb will hang loose 20) Remove intake Manifold 5mm Allen- Remove crossover tube. 21) (- BE CAREFULL-) LINE IT UP RIGHT- Replace intake Manifold (YOU MAY TO SEAL THIS WITH A SEALER LIKE PERMATEX) ( BE SUPER CAREFUL TO KEEP INTAKE COVERED DURING EACH STEP. SCREWS CAN FALL ONTO INTAKE) 22) Drain Float Bowl 3mm allen – very bottom of carb 23) Remove Float Bowl 4 screws (#2 Phillips) let hang down 24) Remove main jet, if Emulsion tube comes out use 8mm and Flat tip to separate jet from Emulsion tube. 25) Install with new jet 26) CAREFULLY Reinstall Float Bowl Cover 27) If installing Needle Remove Top Cover of Carb, Carefully pull the slide out. ( BE CAREFUL WITH DIAPHRAM) Remove Spring + Needle Install new Needle (WE RECOMMEND THE 3RD CLIP FROM TOP WITH TWO WASHERS ON TOP. REINSTALL 28) Be sure to reseat diaphragm – BE CAREFUL Reinstall Cover. 29) Install Carb to Intake – reconnect carb warmer if applicable 30) Reattach idle adjustment 31) Reattach Choke 32) Reattach Bracket in front of Carb- 33) Take Center bolt mount Rubber Gromlet from Stock Air box Plate install in to new Air box Adapter use stock Bolt, Attach to Bracke

Incoming search terms:

Mikuni HSR 42/ 45 Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at ½ to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle.

HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

Incoming search terms:

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

Incoming search terms:

Aprilia Falco Synchronizing the Cylinder Vacuum

0

Filed Under (Aprilia) by admin on 26-10-2010

download
Motorcycle cylinders work quite independently compared to automobiles. Separate carburation, intake manifolds, exhaust pipes and sometimes even independent air filters allow the cylinders to be tuned so that one may be making more power than another. This can be due to differences in air flow, temperature, injection, or valve adjustment betwen the cylinders. Periodically, the cylinders should be synchronized. This is usually done by comparing intake manifold vacuum beneath each throttle and trimming the mixture until balanced. Some old-timers will tell you it can be done by ear, listening to the air flow in each carb throat through a tube stuck in your ear. Most modern tuners have switched to mercury sticks. Rigid tubes stuck in a bath of mercury are attached to the vacuum source. The vacuum draws the mercury up the sticks in proportion to pressure difference between the manifold and the atmosphere. In order to smooth out the individual vacuum pulses, a damping device is needed. This is nothing more than a small orifice (pin hole) restriction in the lines, placed close to the manifold with an air reservoir (length of tube) behind it. Because there is no real air flow in the gauges, there is no pressure drop across the orifice. But when the manifold vacuum drops there is a delay before the gauge pressure can bleed off and it appears steady and readable. Other types of vacuum gauges include mercury-less versions (that draw metal rods), or traditional needle, or “clock” gauges. The clock gauges are very fast acting (they are designed that way so you can see engine problems such as sticking valves). You will definitely need a damper if you choose a clock gauge. I would recommend using two side by side gauges for checking cylinder synch. The reason is, the cylinders are not perfectly independent. As one cylinder drops strength, the idle drops, and this will change the vacuum in the second cylinder’s manifold. It takes a bit of fooling around to get a cause-and-effect feel when you are turning the screws. Swapping gauges would make this difficult

Incoming search terms:

HSR Carburetor Total Kits Installation And Tuning Manual

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
1. Disconnect the battery ground wire from the battery. 2. Turn the fuel petcock to the “OFF” position. 3. Elevate the rear of the fuel tank for better access to the carburetor area. 4. Remove the coil, horn or other devices on the left hand side of the engine to allow free access to the intake manifold bolts. 5. Remove the complete air cleaner assembly, including the backing plate. 6. Disconnect any vacuum hoses and the fuel hose from the stock carburetor. 7. Disconnect the choke cable from the frame. 8. Remove the stock carburetor. 9. Evo: remove the stock manifold. 10. Twin Cam: unplug MAP sensor, remove manifold and then remove the MAP sensor from the manifold. Installation: Intake Manifold: Twin Cam only: Install MAP sensor in Mikuni manifold. 1. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 2. Attach the rubber flange to the Mikuni manifold with the 5/16″x3/4″ bolts and washers. To ease installation, use liqiud detergent to lubricate the manifold seals. Choke: Evo: We recommend that you use the Mikuni choke cable that is furnished with the carburetor. However, you can use the stock Harley cable (’90-’99 models only) if you follow the Twin Cam choke cable instructions. Twin Cam: 1. Remove the Harley choke cable from the stock carb. 2. Remove the Harley spring and plunger from the Harley choke cable. 3. Remove the Mikuni spring and plunger from the Mikuni carburetor. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut. 6. Install the new assembly into the Mikuni. Be careful to only gently tighten the plastic nut.

Incoming search terms:

BMW K1100LT Installing Real Cruise Control

0

Filed Under (BMW) by admin on 26-10-2010

download
The vacuum reserve canister (VRC) is used to provide adequate vacuum for the cruise control servo unit. It uses the throttle body as a vacuum source and, via the vacuum check valve, stores up vacuum for the servo to use to pull the throttle cable. You can also buy one of these at an auto parts store for about $10-15 but I decided to build my own so I could make one that would fit inside the left front of the main fairing body. If you decide to buy one, make sure you can return it if it doesn’t fit inside the fairing or be prepared to mount it somewhere else like inside the tail cowl. I used 8″ of 2″ diameter PVC tubing because that is the length that would easily fit inside the fairing It is mounted inside the fairing in front of the left “bucket.” I used white PVC tubing but, in hindsight, would use black if possible since it is visible to the rider when mounted in the fairing. I suspect that the cruise control may actually work without the use of the vacuum canister so you might want to try the cruise without a VRC. If you do install the cruise control without a VRC, you’ll want to put a vacuum check valve in the vacuum hose that goes from the throttle body to the cruise control servo unit.
11/30/2005 08:23 PM Installing Real Cruise Control on a BMW K1100 Page 4 of 8 used epoxy for assembling the VRC as it’s my permanent adhesive of choice. Cut an 8″ length of 2″ diameter PVC tubing. Sand the edges. Drill two holes as shown for the check valve and vacuum tee. There’s a vacuum tee in the bags of installation miscellany that come with the cruise control. File the webbing from the right angles before gluing it and the check valve in place. Remember to glue the tee into place before gluing the end caps on. Make sure everything has an airtight seal. I used zip-ties to hold it in place inside the main fairing body in front of the left bucket

Honda CBR 400RR Service and Repair Manual

0

Filed Under (Honda) by admin on 16-12-2011

download
Once you have found al1 the identification nurnbers, record thern for reference when nbuying parts. Since the rnanufacturers change specifications, parts and vendors (cornpanies that rnanufacture various cornponents on the
rnachine), providing the ID nurnbers is the only av to be reasonablv sure that vou are buvina Model, c ~ d e and
production year CBR400RR-J (1988) CBR400RR-K (1 989) CBR400RR-L (t990 and 91) CBR400RR-N (1992 and 93) CBR400RR-R (1 994-on) , the correct parts. Whenever possible, take the worn pari to the dealer so direct cornparison with the new cornponent can be rnade. Along the trail frorn the rnanufacturer to the parts shelf, there are nurnerous places that the part can end up with the wrong nurnber or be listed incorrectly. The two places to purchase new parts for
your rnotorcycle – the accessory shop and the rnotorcycle dealer – differ in the type of parts they carry. While dealers can obtain virtually every part for your rnotorcycle, the accessory shop is usually lirnited to norrnal high wear iterns such as shock absorbers, tune-up parts, various engine gaskets, cables, chains, brake parts, etc. Rarely will an accessory outlet have rnajor suspension cornponents, cylinders, transrnission gears, or cases. Used parts can be obtained for roughly half the price of new ones, but you can’t always be sure of what you’re getting. Once again, take your worn part to the breaker for direct cornparison. Whetherhu~ng new, used or rebuilt parts, the best course is to dea1 directly with sorneone who specialises in parts for your particular rnake. Frame nwnber NC23-1020001 t0 1036454 NC23 t090001 t0 10981 16 NC29-1000001 to 101 0598 NC29-1050001 on NC29-l t00001 on Unofficial (grey) imports
All CBR400RR rnodels in the LIK are unofficial (grey) irnports frorn Japan. The rnajority are second-hand rnachines and are allocated age-related licence plates for UK use (the licence plate letter reflects the production year in Japan), although new CBRs are allocated current year UK registration letter plates. Cornrnon changes rnade prior to sale in the UK are the disabling of the rev-lirniter device (or more correctly ‘speed-lirniter’ device), which is fitted to cornply with Japanese rnarket regulations. The device is located inthe speedorneter head and is linked to th

Incoming search terms:

Harley-Davidson Vacuum Operated Switch Kit Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 24-03-2012

download
1. Turn off the ignition switch and disconnect the battery ground cable before proceeding. 2. For applications with Harley-Davidson OE ignition modules, simply replace the existing OE VOES switch with the new Twin Tec switch. Use the supplied crimp terminals to connect the new switch in place of the old switch. The wiring is not polarity sensitive and the two wires from the new switch can be interchanged. 3. For Twin Tec ignitions, refer to the installation instructions supplied with the ignition module for VOES switch hookup. Use the supplied crimp terminals to connect the new switch. The wiring is not polarity sensitive and the two wires from the new switch can be interchanged. 4. Reconnect the battery ground cable when you have completed the installation

Incoming search terms: