passenger foot heat shield fat boy

You search Auto repair manual PDF passenger foot heat shield fat boy, if there are search results will appear below. If search results do not exist, please search by others keyword.



  passenger foot heat shield fat boy Direct Download speed 5282 Kb/s

  passenger foot heat shield fat boy Full Version speed 6162 Kb/s



YAMAHA V-STAR 1300 exhaust system INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Install the bracket (Stamped 439-P, supplied) to the motorcycle chassis using the 10 x 20mm hex head bolt (supplied) and two of the stock mount bolts in the bottom holes (Figure 3). 2. Remove exhaust system and heat shields from protective packaging and place them on a non-abrasive surface such as a blanket or carpet. Using a non-permanent marker or tape, mark outside edge of each heat shield to show location of mounting clips that the hose clamps will loop through (Figure 4). 3. Apply a small amount of anti-seize compound to the threads of the stock O2 sensor and install it into the header assembly. NOTE: Be careful not to overtighten or get anti-seize compound on the sensor tip as this could damage or affect the sensor function. 4. Carefully lay header assembly into the heat shields and loosely install the hose clamps #20 on head pipe heat shields and #24 on collector heat shield (supplied) by feeding the tail end of the clamp into the heat shield clips. Take note of screw head direction (Figure 5), for adjustment purposes they must be accessible when system is installed. NOTE: Do not tighten the clamps at this time. 5. Using stock dome nuts, carefully install system into exhaust ports. (Assistance may be required). NOTE: Install but do not tighten the exhaust nuts at this time. 6. Remove the muffl er heat shield and baffl e assembly from their protective packaging. Place them on a non-abrasive surface such as a blanket or carpet. 7. Insert the large hose clamp (#56, supplied) into the clip on the muffl er heat shield. 8. Carefully slide the baffl e assembly (without damaging the fi berglass packing) into the muffl er heat shield and align the holes in the heatshield with those in the baffl e. Secure the baffl e with the 1/4-20 x 1/2″ button head screws (supplied) and tighten the hose clamp. 9. Install the 5/16″ x 1 1/4″ hex head bolt, washers and locknut (supplied) in the muffl er clamp (supplied) and slip the clamp over the end of the baffl e tube. 10. Slide nut plate (supplied) inside the bracket welded to backside of baffl e (Figure 6). 11. Install the muffl er assembly onto the collector, making sure it slides forward enough to align the edge of the bracket welded to the baffl e with the edge of the mounting bracket. 12. Attach the muffl er assembly to the mounting bracket using the 5/16″ x 5/8″ fl ange head bolts (supplied). 13. Tighten exhaust port nuts evenly on both cylinders. 14. Tighten the muffl er clamp and the 5/16″ fl ange head bolts, securing the muffl er assembly. 15. Insert the O2 sensor plug back into harness and tuck harness back into its original position. Reinstall the cover. 16. Check alignment of heat shields making sure the ends meet squarely to the collector heat shield. Tighten the hose clamps on all the heat shields when properly aligned. 17. Reinstall right side passenger and rider fl oorboards and tighten the 12mm bolts. 18. Check for adequate clearance between all exhaust system components and motorcycle accessories prone to heat damage. 19. All hardware must be properly tightened and the exhaust pipes thoroughly clean before starting motorcycle

Incoming search terms:

HARLEY DAVIDSON SPORTSTER BLACK EXHAUST HEAT SHIELDS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
INSTALLATION Remove Original Equipment (OE) Heat Shields Avoid contact with exhaust system and wear protective clothing that completely covers legs while riding. Exhaust pipes and mufflers get very hot when engine is running and remain too hot to touch, even after engine is turned off. Failure to wear protective clothing could result in burns or other serious injury. (00009a) 1. Allow the motorcycle to cool. 2. Identify the position of the OE clamp screws securing the black heat shields to the exhaust pipes. NOTE The clamp screws are positioned on either side of the exhaust pipe for clearance. 3. See Figure 1. Open the heat shield clamps (1) and spread the bands to remove front and rear heat shields (2) from the exhausts. Retain the heat shield clamps Install Black Heat Shields 1. See Figure 2. Matching the OE position of the heat shield clamps, open the clamps bands and thread the bands through the brackets of the front (1) and rear (2) black heat shields. 2. Spread the band around the exhaust pipes and push the end of the bands to engage the clamp screws. Tighten to hold the heat shields in place. 3. Adjust the shields and heat shield clamps to access clamp screws and to avoid contact with other components. 4. Tighten the heat shield clamp screws

Incoming search terms:

YAMAHA VIRAGO 700/ 1100 2 into 2 EXHAUST SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the slip joint clamp on the front and rear head pipe, which are located at the muffler box. 2. Remove the two nuts that hold the front head pipe to the engine. Slip the head pipe out of the muffler box and set it aside. Note: Do not remove the rear head pipe, it has been incorporated in the design of the new exhaust system. 3. Remove the muffler box mounting bolt located in front of the passenger foot rest on the left side. 4. Remove two bolts from the right passenger foot rest assembly and set the foot rest aside. 5. Slide the muffler box off of the rear head pipe and set it aside. 6. Replace the muffler box mounting bolt (from step #3) using the washer and nut (supplied) on the back side. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Attach the mounting bar to the motorcycle frame behind the right passenger foot rest. Align the two holes in the largest bracket on the mounting bar with the two holes on the frame, be sure the bend in the mounting bar is pointing to the center of the motorcycle. 2. Install the round steel spacer (supplied) to the rear most hole in the bracket. 3. Attach the foot rest using the two 8mm x 1.25 x 25mm bolts (supplied). 4. Slide the new exhaust flange (supplied) onto the front head pipe. 5. Install the two heat shields to the front head pipe using the four hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the heat shields onto the front head pipe. Note: Be sure the bend in the heat shield matches the bend in the head pipe exactly. Wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 6. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 7. Slide a chrome pinch clamp (supplied) onto the expanded end of the new rear head pipe. Install a 3/8″ x 1″ bolt with a flat washer on either side of the clamp followed by a lock nut (hardware supplied). Repeat this step on the inlet end of each muffler using the two muffler clamps with 5/16″ x 1 1/4″ bolts (hardware supplied) but leave the clamp loose at this time. 8. Slip the new rear head pipe with the heat shield attached, over the stock rear pipe and gasket, but leave the clamp loose at this time. 9. Install the front head pipe, with the heat shield attached and stock gasket in place, to the front cylinder using the stock nuts, leave them loose at this time

Incoming search terms:

KAWASAKI VULCAN 700/750 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place the bike on the center stand. 2. Remove the three clamps attaching the heat shield to the left hand head pipe and set the heat shield aside. 3. Remove the two heat shield clamps attaching the heat shield to the right hand head pipe and set the heat shield aside. 4. Loosen the pinch clamps where the mufflers slip onto the muffler box (the black box in front of the rear tire). Remove the bolt attaching the mufflers to the footrest. 5. Remove the left and right hand mufflers and set them aside. 6. Remove the right hand foot rest and brake pedal assembly from the frame. 7. Loosen the pinch clamps where the head pipes slip into the muffler box. 8. Remove the two nuts that secure the right head pipe to the cylinder head. Repeat this step on the left head pipe and save the nuts for reuse. 9. Remove the left and right hand head pipes. Remove the header flange from each head pipe and save the two flanges for reuse. Set the head pipes aside. 10. Remove the two bolts (one on each side) that mount the muffler box to the frame. Lower the muffler box down and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the two bolts from the charcoal canister mount, the canister is located in front of the rear tire. Using the two 6mm x 16mm bolts (supplied) install the centerstand stop bracket, (stamped 205), by aligning the holes in the bracket with the holes in the canister mount. Be sure the bend closest to the holes in the bracket angles towards the rear of the motorcycle and the tang is pointed to the left hand side. Tighten the two 6mm bolts at this time. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns. Repeat this step with the rear heat shield. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 3. Install a three hole mounting bracket to each muffler as shown in figure 1. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note : The muffler bracket stamped #284 is for the right hand muffler, bracket #285 is for the left hand muffler. 4. Install the rear exhaust assembly, with the heat shield attached, to the rear cylinder using the stock flanges and nuts. Install the stock muffler mounting bolts through the rear footrest brackets, the supplied muffler brackets, and finger tighten the nuts. Leave them loose at this time. 5. Repeat step #4 with the front head pipe

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

KAWASAKI VULCAN 1500 PRO PIPE HS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the mufflers by loosening the pinch clamps on the front of each muffler. 2. Remove the muffler mounting bolt from the right side passenger footrest, slide the mufflers off and set them aside. Note: Save the mounting bolt, it will be reused for installation. 3. Loosen the pinch clamp on both front and rear head pipes, they’re located at the resonance chamber (the black box where the pipes meet). 4. Remove the two acorn nuts that mount the head pipe to the cylinder head. Remove the two piece header flange and set it aside. 5. Remove the front head pipe by rotating it down and pull it out of the resonance chamber. 6. Remove the two acorn nuts and flange from the rear head pipe. Remove the two bolts from either side of the resonance chamber and lower rear pipe and resonance chamber down and out and set it aside. 7. Remove the rubber grommets at the resonance chamber mounting points. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the new mounting bracket (stamped 317) to the inside of the stock muffler mounting point (Refer to FIG. 1). 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of all three heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear and collector heat shields. To facilitate the installation of the collector heat shield use a forward sliding motion from the rear of the collector. Do not force the collector heat shield directly onto the collector as damage to the heat shield will result. Note: the collector heat shield uses the 3/8″ wide clamps. 3. Rotate the hose clamps in the shields so that the screw drives are accessible. Tighten only finger tight at this time. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Check to be sure that the stock exhaust gaskets are in good shape. If you have any doubts as to their condition, replace them. 5. Install the header with the heat shields attached, to the front and rear cylinders using the stock nuts and bolts. Leave them loose at this time. 6. Slide the chrome muffler clamp (supplied) onto the inlet end of the megaphone. Install the 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by the 5/16″ lock nut (hardware supplied). Leave the clamp loose at this time. 7. Slip the megaphone onto the head pipe collector, engaging the collector heat shield between the clamp and the outer slip joint tube. Slide one dog bone shaped nut plate under the bracket that

Incoming search terms:

KAWASAKI VULCAN 900 SLASH CUT STAGGEREDS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
1. Attach mounting bracket 440-P to frame using two stock fl ange head bolts used on stock upper bracket (Figures 1 and 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through (Figure 3). 3. Lay front header, and rear header into their head heat shields and muffl er body heat shields. 4. Install #20 hose clamps (supplied) on heat shields and #36 (supplied) on muffl er body heat shields by feeding tail end of clamps into heat shield clips (fi gure 3). Take note of clamp screw head direction (Figure 4). Screw heads must be accessible when system is installed on motorcycle for adjustment purposes. NOTE: Do not tighten at this time. 5. Using stock fl ange nuts, carefully install head pipes into exhaust ports. Assistance may be required. NOTE: Do not tighten at this time. 6. Slide nut plates inside bracket that is welded to backside of muffl er bodies (Figure 5). While holding nut plates in place, attach muffl er bodies to mounting bracket 440-P using two 5/16″x 5/8″ fl ange head bolts (supplied). Leave them loose at this time. 7. Align muffl er bodies so they are level and parallel when viewing from the right side of the bike. Tighten cylinder port exhaust fl ange nuts on front and rear cylinders. 8. Tighten the fl ange bolts on both muffl ers. 9. Tighten all heat shield clamps. 10. Check for adequate clearance of all exhaust system components and motorcycle accessories prone to heat damage. NOTE: For models with fl oorboards, two Spacer washers are supplied to space out the fl oorboard bracket enough to allow the fl oorboard to fold up without hitting the heat shield. 11. Be sure to tighten all hardware before starting your motorcycle. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. NOTE: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up

Incoming search terms:

HARLEY DAVIDSON FXSTD PASSENGER BACKREST AND LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) INSTALLATION Passenger Upright 1. Unscrew the captive screw fastening the seat rear bracket to the fender. 2. Remove the rubber plugs from the three holes in the rear fender where the passenger upright installs. 3. See Figure 2. Fasten the studplate (2) to the fender (A) with the backing plate (3) and three flange locknuts (4). 4. See Figure 1. Fasten the passenger upright (3) to the studplate (1) with three flange locknuts (2). 5. Insert the seat front bracket into the frame, then fasten the seat rear bracket to the fender. NOTE The seat must be temporarily bowed up in the center to fit the seat rear bracket through the slot in the passenger upright. 6. Kit 51144-02 only. See Figure 2. Carefully clean the lower hole (B) on the passenger upright (1) with isopropyl alcohol to remove any grease or dirt. Remove backing from adhesive emblem (5) and press the emblem firmly in to place. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 1 4 3 2 is03890 1. Stud plate 2. Locknut, flange (3) 3. Passenger upright 4. Backrest pad Figure 1. Passenger Upright, Backrest Pad and Luggage Rack Installation NOTE When temporarily removing the passenger upright, the mounting and backing plates may be left in place to simplify passenger-upright re-installation. Thread the flange nuts back onto studs to store the nuts. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) Backrest Pad See Figure 2. Fasten the backrest pad (7) to the passenger upright (1) using the button-head screw (6) as shown. Luggage Rack NOTE See Figure 2. Fasten the luggage rack (8) to the backrest with the backrest pad (7) removed from the studplate (2). -Fasten the luggage rack (8) to the passenger upr ight (1) using the luggage-rack mounting plate (11), button-head screw (12)

Incoming search terms:

HARLEY DAVIDSON SKULL FOOT BOARD INSERT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Kit 50704-04 is an Operator Footboard Insert Kit. •This kit fits all 2004 and later FLHRS/I (Road King® Custom) model motorcycles. •This kitalso fits 1986 and later FLHR/I/CI, FLHT/C/CI/CUI and FLTR/I models equipped with Swept-Wing footboard pans 50683-04 (right) and 50688-04 (left) . Kit 50704-04 contains the following items: QTY DESCRIPTION PART NO. 1Operator footboard insert (right) 50705-04 1Operator footboard insert (left) 50706-04 Kit 50707-04 is a Passenger Footboard Insert Kit. •This kitfits 2004 FLHTCSE models, and all 1986 and later Touring model motorcycles equipped with Swept- Wing Grooved Passenger Footboard Kit 50357-04 . Kit 50707-04 contains the following items: QTY DESCRIPTION PART NO. 1 Passenger footboard insert (right) 50708-04 1 Passenger footboard insert (left) 50709-04 Kit 50710-04 is an Operator Footboard Insert Kit. •This kitfits all 1980 and later Touring models except FLHRS, and 1986 and later FL Softail®model motorcy- cles equipped with footboard pans 50621-79A. Kit 50710-04 contains the following items: QTY DESCRIPTION PART NO. 1Operator footboard insert (right) 50711-04 1Operator footboard insert (left) 50712-04 Kit 50713-04 is a Passenger Footboard Insert Kit. •This kit fits all 1986 and later Touring models . •This kit also fits 1986 and later FL Softail models when equipped with accessory passenger footboard kits (Part Number 50602-89B, 50955-97A, 50955-00 or 50602-00). • This kit iscompatible with Chrome Passenger Footboard Cover Kits (Part Numbers 50782-91, 50193-96, 50194-96 and 50246-00). • This kit is notcompatible with Leather Passenger Footboard Fringe Kits (Part Numbers 50947-98 or 50956-98). Kit 50713-04 contains the following items: QTY DESCRIPTION PART NO. 1 Passenger footboard insert (right) 50714-04 1 Passenger footboard insert (left) 50715-04 Installation, Kit 50704-04 (For Swept-Wing Operator Footboards): Removing Previously Installed Inserts 1. Apply liquid dishwashing soap to the rubber beads protruding through the bottom of the footboard pan. 2. With the operator footboard in the “up” position, use a screwdriver to work the rubber footboard beads out through the top of the footboard. 3. Repeat the above steps for the remaining footboard insert. Installing the New Inserts 4. Apply liquid dishwashing soap to the rubber beads on the new footboard insert. 5. Place the footboard insert into position on the footboard pan. From the underside of the footboard, use a pliers to pull each rubber bead into its mating hole in the footboard pan until the beads protrude through the pan. 6. Repeat the above steps for the remaining footboard insert.

Incoming search terms:

HARLEY DAVIDSON PASSENGER FOOTBOARD INSERT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION If replacing an insert or inserts on a vehicle currently equipped with Swept Wing Passenger Footboards: Existing Footboard Insert Removal NOTE Carefully remove the currently installed footboard insert to avoid damage to chrome surfaces. 1. See Figure 1. Fold the passenger footboard (1) into the UP position. 2. Loosen, but do not remove the footboard insert setscrew (2). 3. With the footboard folded DOWN, carefully raise an outside corner of the existing insert with a suitable flat-bladed tool, taking care to avoid damaging the chrome footboard pan. 4. Continue around the insert, using a second tool if necessary to pry the existing insert (3) from the footboard pan. 5. If replacing both inserts, repeat for the opposite footboard. Swept Wing Passenger Footboard Installation 1. If installing inserts on a vehicle NOT currently equipped with Swept Wing Passenger Footboards: •Remove currently installed passenger footboards (if so equipped) per the instructions included with the Swept Wing Passenger Footboard Kit. •Remove currently installed passenger footpegs (if so equipped) by removing the socket screw with lockwasher retaining the footpeg support bracket to the rear fork (swingarm) bracket. 2. Follow the instructions in the Swept Wing Passenger Footboard Kit to install the passenger footboards. Footboard Insert Installation 3. ALL applications: Center the two footboard pivot pins. 4. Use soapy water to moisten the rubber dowel pins and pivot pin slots on the bottom of the new footboard insert. 5. Place the insert into position with the rubber dowel pins mating the holes in the footboard pan. Firmly press the insert into the footboard until the dowel pins pop into place. 6. Fold the passenger floorboard UP and tighten the setscrew to secure the insert. 7. Repeat Steps 3 through 6 for the opposite footboard. NOTE Avoid the contact of chrome surfaces with abrasive materials (stones, sand, etc.) as damage will result

Incoming search terms: