pinion joint 2009 honda 420 rancher irs

You search Auto repair manual PDF pinion joint 2009 honda 420 rancher irs, if there are search results will appear below. If search results do not exist, please search by others keyword.



  pinion joint 2009 honda 420 rancher irs Direct Download speed 5282 Kb/s

  pinion joint 2009 honda 420 rancher irs Full Version speed 6162 Kb/s



HONDA 420 RANCHER 2×4/4×4 2007-2009 CLUTCH KIT INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-12-2011

download
Remove key from the ignition switch. Remove the side panels from both sides. Remove both foot wells. 2. Drain coolant. Remove the oil drain plug from the motor; if you carefully drain it into a clean container you should be able to reuse it. 3. Disconnect shift motor (on electric shift models only). Remove coolant hoses. 4. Remove the bolts that mount the front differential to the frame, no other parts need to be removed. Carefully slide the front differential towards the front of the machine; you might need to lift up slightly to get the differential to move. Remove the drive shaft. Remove o-ring on output shaft (on motor). 5. Remove the fuel pump. 6. Loosen the front crankcase cover bolts, keep track of each bolt length and location. Slowly remove the crankcase cover. Carefully watch for o-ring shims and dowel pins that may fall out. 7. Unstake the nut holding the clutch on and remove nut. Using Honda tool #07933-HB3000A thread the large part of the tool into the center of the clutch. Tighten the center bolt on the tool while holding the large part of the tool with a wrench. This will pull the clutch off the machine. Place the clutch on a clean work surface. EPI performance.com
8. Using the c-clamps push down slightly on the outside cover and remove the four e-clips. Keeping track of which way they come off, remove the round metal plates one at a time. This will allow you to see the complete spring. Remove one end of each spring using a spring tool or needle nose pliers and then remove springs. Install the EPI springs by inserting the spring into the outer edge first. Using a spring tool or pliers (45 degree bent pliers work well) pull on the spring and insert the end into the hole. Install the metal plates and the e-clips. If you can’t get the plates to sit flat make sure each clutch arm is flat against the bottom plate of the clutch. Occasionally when you put the springs on, the clutch arms will pop up. Slide the clutch into the machine. The Sprague clutch is marked “outside” when installing make sure this is facing out. Torque clutch nut to 87 ft/lbs. 9. Clean the gasket surface on the motor and on the cover. Put a thin layer of Honda Bond or Yamabond semi-drying liquid gasket (or something similar as long as it is semi-drying) on the crankcase cover. Carefully install crankcase cover, do not force cover on. Torque bolts to 9 ft/lbs. 10. Install the fuel pump. 11. Install the o-ring on the output shaft (on motor) and install the drive shaft. Carefully slide the front differential back into place and mount to the frame. Install the coolant hoses. Refill your engine coolant to the proper level according to your owner’s manual. 12. Install the oil drain plug. Refill your engine to the proper level according to your owner’s manual. You can reuse your oil if it is clean and was drained into a clean container. Only use manufactures recommended oil. 13. Be sure to double check coolant and oil levels and to look for any leaks after the machine has run for a few minutes. 14. Go out and ride your machine. If your performance doesn’t seem right double check to make sure everything has been done properly. 15. EPI is constantly testing our products. Sometimes there is a need to contact the user with new technical information. To ensure that you are receiving this information visit our web site EPIperformance.com to register your clutch kit.

Incoming search terms:

Honda 2007-2010 Rancher 420 ATV Rear Bumper Installation

0

Filed Under (Honda) by admin on 22-12-2011

download
Honda Rancher 420 ATV Rear Bumper (2007-2010) Installation Instructions 1. Attach top bumper attachments to top rack. 2. Attach the rear bumpers lower attachment point to vertical bars

Incoming search terms:

2009 Honda CRF450R Decompression Plunger PRODUCT UPDATE CAMPAIGN

0

Filed Under (Honda) by admin on 21-04-2011

download
JH2PE053*9K700001 thru JH2PE053*9K703372 (*) Denotes check digit UPDATE PROCEDURE DEALER VENTORY Any affected unit in your inventory must be updated with a new decompression plunger and weight before delivery to the customer. Refer tothe PARTS INFORMATION and the UPDATE PROCEDURE sections of thisb Service Bulletin. Refer to the 2009 CRF450R Service Manual for specific removal instructions. 1. Remove the seat (page 3-3). 2. Remove the shrouds (page 3-4). 3. Properly hang the fuel tank (page 4-6). 4. Remove the camshaft (page 9-10) CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your Honda. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your Honda, or that your Honda has the condition described. To determine whether this information applies, contact an authorized Honda dealer. 5. Replace the decompression weight and plunger with kit parts (page 9-14). 6. Reinstall all previously removed parts. IDENTIFICATION When you have completed the update, place a punch mark before the first digit of the V.I.N. located on the right side of the steering head. 0080 WARRANTY INFORMATION This Product Update Campaign ends on arch 7, 2012. Normal claim submission requirements apply. fter completing the UPDATE PROCEDURE,submit one warranty claim per unit with the following information: WARRANTY CLAIM TEMPLATE: Template: R02A* Flat Rate Time: 1.2 hours *Template reads “R-zero-2-A”.

Incoming search terms:

Daytona 675, Street Triple Street Triple R Fitting Instruction

0

Filed Under (Triumph) by admin on 29-10-2010

download
remove the original gear selector rod from the motorcycle. Note: The ball joint and locknut on the transmission linkage have a left hand thread. This is identified by either a machined ring on the gear selector rod on Daytona 675 or on the ball joint on Street Triple and Street Triple R. 1. Front ball joint 2. Locknut 3. Gear selector rod 4. Machined ring, left hand thread identification 5. Machined ring, left hand thread identification (StreetTriple and Street Triple R) 6. Remove the front and rear ball joints and front locknut only from the gear selector rod. Retain the locknut and both ball joints for re-use. Retain the gear selector rod if the motorcycle is to be returned to its original condition. 7. Remove the plastic end caps from the quickshifter assembly. 8. Screw the locknut on to the rear of the quickshifter assembly (right hand thread) leaving 8mm of thread exposed. 1. Quick shifter assembly 2. Locknut 9. Screw the rear ball joint (right hand thread) on to the rear of the quickshifter assembly until it contacts the locknut. Unscrew the ball joint, only enough to achieve the correct orientation in relation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 10. Fit the locknut and front ball joint (left hand thread) to the front of the quickshifter assembly Screw the locknut and ball joint on to the quickshifter assembly to achieve a dimension between the ball joint ends of 203.5 mm. Ensure that the ball joint is in the correct orientation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 12. Route the quickshifter cable through the gear selector rod aperture in the frame, as shown. 1. Quickshifter cable 2. Gear selector rod aperture 13. Locate the quickshifter assembly in position, through the frame with the sensor at the rear and the cable at the top. 1. Quick shifter assembly 2. Sensor 14. Attach the front ball joint to the transmission linkage. 1. Ball joint 2. Transmission linkage

Incoming search terms:

2000 Honda Rancher ATV Winch Mounting Kit REMOVAL AND INSTALLATION

0

Filed Under (Honda) by admin on 13-01-2012

Begin by removing the front fascia and front skid plate on the vehicle as shown in figure 1. Save the fasteners as they will be used later to re-install the front fascia and skid plate. 2. Remove the 8mm bolts on both sides located inside the front tires and on the ends of two horizontal tubes on the front tube frame as shown in figure 2. 3. Place the mounting plate (A1) inside the front tube frame. The tabs with the slotted holes facing down. The slotted tabs should align where the
two 8mm bolts were removed in step 2. Reinstall these two bolts at this time thighten to just fingertight. Install the two 1/4-20 u-bolts (B3) and locking hex nuts (B1) and flat washers (B7) at thism time see figure 3, do not tighten down at this time. so the plate can be adjusted for position see figure 2. 4. Place the rear support bracket (A4) into position
and attach with the two 5/16-18 x 3/4 hex cap screws (B6), flat washer (B5) and locking nut (B4). Adjust the position of the support bracket so that it comes in contact with the frame tubes and tighten the fasteners see figures 3 and 4.
Make sure the support bracket maintains contact with the rear frame tubes and tighten down the two front 8mm mounting bolts. Tighten the bolts to a recommended torque of 12 ft-lb (17 N-m). 5. Attach the fairlead bracket support (A2) to the front frame tubes see figure 5. The support bracket attaches behind the front tubes. Space the bracket away from the tubes using the spacer brackets (A3). Attach the brackets using the 1/4- 20 u-bolts (B2), lock nuts (B1) and flat washers (B7). Before tightening the u-bolts make sure the bracket is in the correct position by fitting the front
fasica into postion and checking location. Tighten the nuts to a recommended torque of 7 ft-lb (10 N-m). NOTE: If this kit is being installed on a 00 to 03 Honda the wider fairlead bracket (A2) will need to be used. This will require the use of the
wider u-bolts (B3). The spacer brkts (A3) will not be required when installing the wider fairlead brkt

HONDA ATV Carburetor Repair Kits Installation

0

Filed Under (Honda) by admin on 21-12-2011

download
ATV Carburetor Repair Kits Complete kits to rebuild one OEM carburetor. Each kit contains necessary gaskets/o-rings, needle valve or needle valve set, and jets. Made in Japan. Note: Check all parts before installation. Honda Model Year Order No AT C70 78-85 025-001 AT C90 70-71 025-003 ATC90K1/K2/K3 72-75 025-003 AT C90 76-78 025-003 TRX90 Fourtrax 90 93-98 025-084 ATC110 79-83 025-005 ATC110 84-85 025-061 ATC125M 84-85 025-062 TRX125 Fourtrax 85-86 025-050 TRX125 Fourtrax 87-88 025-063 ATC185 1980 025-009 ATC185S 81-83 025-009 AT C200 81-82 025-008 AT C200 1983 025-009 ATC200E Big Red 82-83 025-064 ATC200ES Big Red 1984 025-064 AT C200M 84-85 025-064 AT C200S 84-86 025-065 AT C200X 83-85 025-012 AT C200X 86-87 025-014 TRX200 Fourtrax 200 90-91 025-066 TRX200D Fourtrax 200 Type II 1991 025-066 TRX200D Fourtrax 200 Type II 92-93 025-067 TRX200D Fourtrax 200 Type II 94-97 025-068 TRX200SX Fourtrax 87-88 025-069 ATC250R 81-82 025-017 ATC250R 83-84 025-018 AT C250R 1985 025-019 ATC250ES Big Red 85-87 025-029 AT C250SX 1985 025-070 TRX250 Fourtrax 250 1985 025-071 TRX250 Fourtrax 250 86-87 025-072 TRX250EX Sportrax 250EX 01-04 025-085 TRX250R Fourtrax 250R 86-87 025-060 TRX250R Fourtrax 250R 1988 025-073 TRX250X 91-92 025-074 TRX300 Fourtrax 300 1988 025-075 TRX300 Fourtrax 300 91-92 025-076 TRX300 Fourtrax 300 93-95 025-078 Honda Model Year Order No TRX300EX Fourtrax 300EX 93-98 025-081 TRX300FW Fourtrax 300 4×4 1988 025-075 TRX300FW Fourtrax 300 4×4 91-92 025-076 TRX300FW Fourtrax 300 4×4 93-95 025-078 AT C350X 1985 025-035 TRX350 Fourtrax 4×4 86-87 025-079 TRX350FE Fourtrax Rancher 4×4 ES 00-03 025-082 TRX350FM Fourtrax Rancher 4×4 00-03 025-082 TRX350TE Fourtrax Rancher ES 00-03 025-082 TRX350TM Fourtrax Rancher 00-03 025-082 TRX350D Fourtrax Foreman 4×4 87-89 025-079 TRX400FW Fourtrax Foreman 95-00 025-080 TRX450ES Fourtrax Foreman ES 98-01 025-083 TRX450FE Fourtrax Foreman ES 02-03 025-083 TRX450FM Fourtrax Foreman S 02-03 025-083 TRX450S Fourtrax Foreman S 98-01 025-083 TRX500FAFourtrax Rubicon 01-04 025-086

Incoming search terms:

1989-2000 Honda XR’S WHEEL REMOVAL AND SERVICE TOOLS

0

Filed Under (Honda) by admin on 15-12-2011

download
ATV BALL-JOINT SOCKET This tool is designed remove and install nut on Yamaha YFM350X Warrior. 35-8581 ATV Ball-Joint Wrench ATV BALL-JOINT SEPARATOR This tool is designed to separate the knuckle-ball joints on ATV’s without damage to the A-arm, ball joint stud or rubber boots. Sold as a kit with two separate press bolts to fit a variety of applications. Fits the following ATV applications: HONDA: TRX250R 86-89, TRX250X 87-88 & 90-91, TRX300EX 93-98 YAMAHA: YFZ350 Banshee 87-02, YFM350X Warrior 87-96 35-1975 ATV Ball-Joint Separator

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

2008-2009 HONDA CBR 1000 RR DUAL CANISTER SLIP-ON INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-11-2011

download
INSURE THE EXHAUST SYSTEM AND EXHAUST COMPONENTS ARE FULLY COOLED. 2. INSURE THE MOTORCYCLE IS STABLE ON KICKSTAND OR REAR CENTERSTAND OR SERVICE TABLE. 3. REMOVE THE 3 PLASTIC BUTTONS HOLDING THE PLASTIC COVER OVER THE EXHAUST SERVO. (THIS IS LOCATED DIRECTLY INSIDE THE RIGHT REAR PASSENGER PEG BRACKET) DETACH THE CABLE END FROM THE SERVOnWHEEL AND REMOVE THE ENTIRE CABLE FROM THE RETAINING CLIP. THE ENTIREnCABLE WILL NOW REMOVE WITH THE REST OF THE EXHAUST.REPLACE THE PLASTIC COVER FOR THE SERVO AND REINSTALL THE 3 PLASTIC BUTTONS. 6. REMOVE THE STOCK MUFFLER MOUNTING BOLT. REMOVE 7. REMOVE THE STOCK EXHAUST CLAMP. (IT IS NOT UNCOMMON FOR THE CLAMP BOLT TO BREAK DURING REMOVAL.)b8. REMOVE THE ENTIRE STOCK EXHAUST ASSEMBLY. BE CAREFUL NOT TO SCRATCH THE SWING ARM DURING REMOVAL. 9. REMOVE THE STOCK EXHAUST GASKET FROM HEADER PIPE IF IT DID NOT COME OFF WITH THE STOCK EXHAUST. THIS GASKET WILL
NOT BE USED. 10. PREASSEMBLE THE HYPERFLO EXHAUST BEFORE INSTALLING. HYPERFLO RECOMMENDS YOU DO THIS PORTION ON CARPET OR A CLEAN PADDED AREA. YOU MAY ALSO USE THE PLASTIC BUBBLE PACKAGING AS A PAD TO PROTECT THE CANISTERS DURING PREASSEMBLY. 11. PREASSEMBLE THE LARGE DIAMETER CAN TO THE S-PIPE FIRST. INSTALL THE SPRING ON THE CANISTER FIRST AND PULL AWAY FROM THE CANISTER TO INSURE YOU DO NOT SCRATCH THE CANISTER

2009 HONDA CBF1000 Specifications/ Press Information

0

Filed Under (Honda) by admin on 18-02-2011

download
Specifications General Model CBF1000 Mold Type ED-type Engine Type Liquid-cooled 4-stroke 16-valve DOHC inline-4 Displacement 998cm³ Bore x Stroke 75 x 56.5mm Compression Ratio 11 : 1 Max. Power Output 72kW / 8,000min-1 (95/1/EC) Max. Torque 93Nm / 6,500min-1 (95/1/EC) Idling Speed 1,200min-1 Oil Capacity 3.6 litres Fuel System Carburation PGM-FI electronic fuel injection Throttle Bore 36mm Aircleaner Dry, cartridge-type paper filter Fuel Tank Capacity 19 litres (including 4-litre reserve) Electrical System Ignition System Computer-controlled digital transistorised with electronic advance Ignition Timing 5° BTDC (idle) ~ 45° BTDC (7,500min-1) Sparkplug Type NGK: CR8EH-9; ND: U24FER9 Starter Electric Battery Capacity 12V / 8.6AH ACG Output 330W Headlights 12V, 55W x 1 (low) / 55W x 2 (high) Drivetrain Clutch Wet, multiplate with coil springs Clutch Operation Hydraulic Transmission 6-speed Primary Reduction 1.604 (77/48) Gear Ratios 1 2.714 (38/14) 2 1.941 (33/17) 3 1.579 (30/19) 4 1.363 (30/22) 5 1.217 (28/23) 6 1.115 (29/26) Final Reduction 2.687 (43/16) Final Drive #530 O-ring sealed chain Frame Type Mono-backbone; rectangular-section steel tube Chassis Dimensions (LxWxH) 2,156 x 781 x 1,138mm Wheelbase 1,480mm Caster Angle 26° Trail 110mm Turning Radius 2.8m Seat Height 795mm (±15mm) Ground Clearance 130mm Kerb Weight 242kg (F: 118kg; R: 124kg), *250kg (F: 120kg; R: 130kg) Max. Carrying Capacity 195kg Loaded Weight 437kg , *445kg Suspension Type Front 41mm cartridge-type telescopic fork, 120mm axle travel Rear Pro-Link with gas-charged HMAS damper, 120mm axle travel Wheels Type FrontHollow-section 6-spoke cast aluminium RearHollow-section 6-spoke cast aluminium Rim Size Front17M/C x MT3.50 Rear17M/C x MT5.00 Tyre Size Front120/70 ZR17M/C (58W) Rear160/60 ZR17M/C (69W) Tyre Pressure Front 250kPa Rear 290kPa Brakes Type Front 296 x 4.5mm dual hydraulic disc with 4-piston (*Combined 3-piston) calipers, floating rotors (*ABS) and sintered metal pads Rear 240 x 6mm hydraulic disc with single-piston (*3-piston) caliper (*ABS) and sintered metal pads

Incoming search terms: