piston ring installation 04 harley fatboy

You search Auto repair manual PDF piston ring installation 04 harley fatboy, if there are search results will appear below. If search results do not exist, please search by others keyword.



  piston ring installation 04 harley fatboy Direct Download speed 5282 Kb/s

  piston ring installation 04 harley fatboy Full Version speed 6162 Kb/s



Harley-Davidson Big Twin Evolution and Twin Cam Edelbrock/ JE Sport INSTALLATION INSTRUCTIONSsman Pistons

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION PROCEDURE Note: All Evolution® “Big Twin” pistons are marked “Front” or “Rear” and come with rings, wrist pins, and locks. • Note: We highly recommend that a dealer or trained mechanic perform the installation of these pistons. Specialized equipment is required for honing and finishing the cylinders to ensure long life of the piston and cylinder assembly. 1. Remove original equipment cylinders from engine. Refer to a shop manual or other reference book for specific steps, if needed. (Note: Care should be taken not to bend the studs or damage the cylinder during removal of the cylinders.) 2. With a small screwdriver, move the wrist pin retainer around to gain access to the tail of the retainer as it lines up with the notch in the bottom of the wrist pin hole. 3. Use a small screwdriver, pick or awl to roll the wrist pin retainer out of its groove. 4. Push wrist pin out and remove piston. 5. Repeat procedure for the other piston. 6. At this point, take cylinders, new pistons, and piston-to-wall clearance specifications to your dealer or machine shop to perform necessary machining operations. • IMPORTANT NOTE (Evolution® and Twin Cam®): The cylinder bore must be machined/honed to provide .0025″ of piston-to-wall clearance. Measure the piston diameter at a point .500″ up from the lower skirt (See Figure 3). 7. Starting with the front cylinder, install new piston rings and one wrist pin retaining clip (Note: Second ring has a dot which must face up when the ring is installed) . 8. Place the piston over the conecting rod, making sure that the intake valve pocket is towards the intake side. (For Evolution ® , see Figure 1. For Twin Cam ® , see Figure 2) . Coat the wrist pin with engine oil and insert it into the piston. Install the second wrist pin retainer into the groove. 9. Lightly coat the piston skirt with engine oil. Place a piston ring compressor over the piston/ring assembly and compress. Place the cylinder over the piston and gently push down until all rings are in the cylinder. Remove the ring compressor, and push the cylinder the rest of the way down. (Note: Be careful not to get oil onto the base gasket.) 10. Place two nuts and washers on opposite corners of the #1 cylinder to hold it down while you repeat the procedure for cylinder #2. 11. Assemble the rest of the engine per factory specifications. Start the engine and let it run at 2000 rpm for about 10 minutes.

Incoming search terms:

HARLEY-DAVIDSON V-ROD BIG BORE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
The cylinder sleeves provided with the Wiseco V-Rod big bore kit have been finished honed to size and the piston to cylinder clearance has been set. Prior to installation, the sleeves must be washed in hot soapy water (not parts washer solvent) and dried. Coat the bore surface with motor oil and wipe it with a white towel. If the towel shows any remaining grit, repeat the hot soapy water washing process until the towel will only show clean motor oil. CAUTION: Test fit the cleaned sleeve (without O-Rings installed) into the engine block. Sleeve should drop into position. If sleeve will not easily drop into position, warm the engine block with a hair dryer until sleeve will drop into position. Remove sleeve, then continue installation procedures. From the bottom side of the sleeve, gently roll the 2-cylinder sleeve O-rings into the two grooves on each sleeve. Apply motor oil to the O-rings and gently install the sleeves into the block until bottomed. CAUTION: DO NOT ATTEMPT TO INSTALL SLEEVES WITHOUT LUBRICATING THE O-RINGS. FAILURE TO LUBRICATE O-RINGS COULD RESULT IN TORN OR DAMAGED O-RINGS THAT WOULD NOT BE EVIDENT UNTIL ENGINE WAS STARTED. INCORRECTLY INSTALLED O-RINGS CAN RESULT IN CATASTROPHIC ENGINE DAMAGE. NOTE: REFER TO THE OEM SERVICE MANUAL FOR ALL TORQUE SPECIFICATIONS PISTON RING PREPARATION Wiseco V-Rod pistons incorporate an advanced 2 ring system • The top ring is file-fit, and as such, requires that the end gap must be clearanced. The proper end gap clearance is .016-.018″ with the ring installed squarely in the bore. The top ring must be installed on the piston with the dot marking toward the top of the piston. • The oil ring is comprised of the expander and two rails. Install the expander first, and then the rails. Check to make sure the expander tips have not overlapped. It is not necessary to clearance the end gaps on the oil rails. The rails should be installed without modification. PISTON INSTALLATION The Wiseco V-Rod big bore kit is supplied with pistons that are front and rear cylinder specific. Install the front piston 4792M10795 in the front cylinder with the arrow facing the front of the engine. Install the rear piston 4793M10795 in the rear cylinder with the arrow facing the front of the engine. A piston ring compressor is required to install the pistons into the cylinders. Front of engine ➔ 4792M10795 ( Front piston) 4793M10795 ( Rear piston) FWD 4793M10795 FWD 4792M10795 For further information call the Wiseco Tech Line:

Incoming search terms:

HARLEY DAVIDSON XL CHROME FORWARD CONTROL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
2008-05-05 XL CHROME FORWARD CONTROL KIT GENERAL Kit Number 33395-04, 33398-04 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harley- davidson.com (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 5, Figure 6 and Table 1. INSTALLATION Remove Stock Shift Lever and Footrest Assembly 1. See Figure 1. Loosen the shift lever retaining screw (2) securing the shift lever (1) to the shifter shaft. Slide the shift lever off the splined shaft. Remove shifter peg from lever and save for installation. Discard shift lever. 2. Remove the two socket head screws (4) securing the footrest bracket (3) to the frame and remove footrest. Discard screws. 3. See Figure 5. Obtain two hole plugs (1) from kit and firmly press plugs into frame screw holes remaining from footrest removal. 4. See Figure 2. Remove the retaining ring (1) from the clevis to free the footrest clevis pin (4). Remove the clevis pin and footrest (3) from the footrest support. Save footrest for installation. Discard retaining ring, clevis pin, spring washer and footrest bracket. 1 2 4 3 is 01887 1. Shift lever 2. Retaining screw 3. Footrest bracket 4. Socket head screw Figure 1. Remove Shift Lever and Footrest 5 1 3 2 4 is 01901 1. Retaining ring 2. Spring washer 3. Footrest 4. Clevis pin 5. Footrest bracket Figure 2. Remove Left Footrest from Support Remove Stock Brake Pedal and Footrest Assembly 1. See Figure 3. At the right footrest, remove the retaining ring (1) clevis pin (2), footrest (3) and spring washer (4). Discard all hardware but save footrest for installation. 2. Remove brake rod (5) from brake pedal and master cylinder bell crank. Discard brake rod. 3. Remove the two screws (6) and right footrest/brake pedal support bracket with attached brake assembly from frame

HARLEY DAVIDSON FLUSH-MOUNT LED FUEL GAUGE AND GAS CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove stock gas cap from fuel tank. 2. Clean and wipe inside surface of fuel tank filler cup, O-ring seal surface, and trim ring adhesive surface with a mixture of equal parts of isopropyl alcohol and distilled water. 3. See Figure 1. Install gas cap into fuel tank. is00407 Figure 1. Screw in Gas Cap is00466 Figure 2. Note Position of Arrow on Trim Ring 4. Push down on gas cap and rotate clockwise one-eighth of a turn to lock. To unlock, push down on gas cap and rotate counterclockwise one-eighth of a turn. 5. See Figure 2. Before removing adhesive backing, note position of arrow on inside diameter of chrome trim ring. NOTE As you rotate trim ring, you will see gaps between trim ring and fuel tank. Rotate trim ring to position that best eliminates gaps between fuel tank and trim ring. Rotation of trim ring should be minimal. 6. See Figure 3. With the arrow pointing toward front of motorcycle, rotate chrome trim ring slightly to determine best position of bottom chrome trim ring to contour of the fuel tank 7. See Figure 4. Mark position of chrome trim ring with masking tape or grease pencil. 8. Carefully cut masking tape with a hobby knife making sure not to scratch chrome trim ring or paint surface on fuel tank. 9. Peel off adhesive backing from chrome trim ring. 10. Using gas cap to center and masking tape (or grease pencil mark) to align, press chrome trim ring firmly into position for about ten seconds. 11. Peel off masking tape (or remove grease pencil mark) from chrome trim ring and fuel tank. 2 1 is00414a 1. Masking tape 2. Cut masking tape Figure 4. Align Trim Ring and Press into Place NOTE Allow adhesive trim ring to cure for about 5-7 minutes before you continue with kit installation. Install Flush-Mount LED Fuel Gauge 1. Remove the seat following the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove stock fuel gauge. Refer to service manual for instructions. 4. Insert wires down tube of fuel tank from LED fuel gauge. 5. See Figure 5 and Figure 6. Insert LED fuel gauge in the fuel tank cup

Incoming search terms:

HARLEY DAVIDSON SPORTSTER FORWARD CONTROL KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
Remove Stock Shift Lever and Footrest Assembly 1. See Figure 1. Loosen the shift lever retaining screw (2) securing the shift lever (1) to the shifter shaft. Slide the shift lever off the splined shaft. Remove shifter peg from lever and save for installation. Discard shift lever. 2. Remove the two socket head screws (4) securing the footrest bracket (3) to the frame and remove footrest. Discard screws. 3. See Figure 6. Obtain two hole plugs (1) from kit and firmly press plugs into frame screw holes remaining from footrest removal. 4. See Figure 2. Remove the retaining ring (1) from the clevis to free the footrest clevis pin (4). Remove the clevis pin and footrest (3) from the footrest support. Save footrest for installation. Discard retaining ring, clevis pin, spring washer and footrest bracket. 1 2 4 3 is03193 1. Shift lever 2. Retaining screw 3. Footrest bracket 4. Socket head screw (2) Figure 1. Remove Shift Lever and Footrest 5 1 3 2 4 is03194 1. Retaining ring 2. Spring washer 3. Footrest 4. Clevis pin 5. Footrest bracket Figure 2. Remove Left Footrest from Support Remove Stock Brake Pedal and Footrest Assembly 1. See Figure 3. At the right footrest, remove the retaining ring (1) clevis pin (2), footrest (3) and spring washer (4). Discard all hardware but save footrest for installation. 2. Remove the exhaust to access the brake rod. Follow the instructions in the appropriate Service Manual. 3. Remove brake rod (5) from brake pedal and master cylinder bell crank. Discard brake rod INSTALLATION Install Forward Control Brake Pedal and Footrest Assemblies 1. See Figure 5 and Figure 6. At the lower front of the right frame downtube, remove the two screws securing the J- clip (B) to the frame. Discard the screws but save J-clip for installation. 2. Install the other end of the brake rod into the brake pedal assembly (8). Tighten to 84-144 in-lbs (9.5-16.3 Nm) . NOTE Assemble the brake pedal and footpeg clevis onto the footrest support bracket (as described in the next step) prior to mounting the support bracket to the frame. This will allow easier installation of the footrest mount clevis retaining ring (installed to grooved end of footrest mount clevis). 3. Slide the brake pedal (8) onto footrest mount clevis (11) then slide clevis into footrest/brake pedal support bracket (9). Align hole in the clevis with hole in the support bracket and install screw (6). Tighten the screw to 18-22 ft-lbs (24.4-29.9 Nm) . 4. Install the footrest mount clevis retaining ring (18) to the groove at the end of the footpeg clevis. 5. Position the J-clip (from Step 1) against the frame aligning the mounting holes. Mount the footrest/brake pedal support bracket (9) and J-clip to frame using the new screws (3). Tighten the bracket to 45-50 ft-lbs (61.1- 67.9 Nm) . 6. Obtain the brake rod (15) from kit and thread one end into the master cylinder bell crank. Tighten to 120-180 in-lbs (13.6-20.3 Nm) . 7. Install footpeg on clevis with spring washer (2). Make sure spring washer is positioned inside clevis (11) with the square edge toward the inside. Align holes and push clevis pin (7) from top down through hole in clevis. Secure clevis pin using the new retaining ring (17). 8. Install exhaust following the instructions in the appropriate Service Manual. Install Forward Control Shift Lever Assembly

Incoming search terms:

HARLEY DAVIDSON 80-SPOKE REAR WHEEL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
Additional Parts Required This kit includes the custom wheel only. Proper installation of this kit requires the separate purchase of the following parts which are available at a Harley-Davidson dealer: •Wheel Bearing Remover and Installer (HD-44060) •Wheel Installation Kit (See Service Parts Tables for part number) The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See the Service Parts section for kit contents. INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. NOTE Remove the rear brake caliper before removing the wheel. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. Install the tube and tire on wheel. Refer to REAR WHEEL in the Service manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) NOTES Install the primary bearing first using appropriate Service Manual and WHEEL BEARING REMOVER/INSTALLER. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to REAR WHEEL in Service Manual. 4. Install rear wheel (1), stock axle and stock axle nut. Refer to REAR WHEEL in Service Manual

Incoming search terms:

Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO CB RADIO KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
2006 models: communication switch 77173-06 2007 models: communication switch 77173-07 2008 models: communication switch 77173-08 FLHT models will require prior installation of: •Advanced Audio AM/ FM/ CD Radio Kit (76412-06) •AM/ FM Antenna Kit (76325-06 or 76317-06) Unless one has already been fitted as part of another Advanced Audio kit installation: 2006-2007 FLHX models will require the separate purchase of: •fuel tank console (61270-98A), •tank console gasket (71294-89), •a button-head screw (3652), •nut (7964) •clip (10103 and 10120). •tank pod mounting screws (2462) quantity 3 •FLHT trim piece (52447-96) and cb pod trim badge 2008 FLHX models: •fuel tank console (61270-08) •clips (10103 and 10120) NOTE The console screws, fuel door, gasket, mounting bracket will all need to be reused. FLTR models will require the separate purchase of: •a Console Pod Assembly (77136-03), and •three pan-head screws (2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (70169-06), and EITHER : •a Premium Stereo Helmet Headset (77147-98) OR a Hand-Held CB Microphone Kit (76312-98), All of these items are available from a Harley-Davidson Dealer. If two modules are already installed on top of the radio, two Dual-LockTM mounts, (76434-06), will be needed. Models WITHOUT a Tour-Pak installed will require the additional purchase of a Frame Mount CB Antenna Kit (76415- 06). Models WITH a Tour-Pak installed will require the additional purchase of a Tour-Pak Mount CB Antenna Kit (76414-06). All of these items are available from a Harley-Davidson Dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Electrical Overload It is possible to overload your motorcycle’s charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicle’s charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. See a Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories, or for necessary wiring changes. (00211b)

Incoming search terms:

HARLEY DAVIDSON CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT GENERAL Kit Number 56032-08 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only). This kit does not fit models equipped with a hydraulic clutch, handlebar mounted gauges or the Road Tech® Radio. Additional Parts or Accessories Required Separate purchase of additional parts or accessories is required for proper installation of this Handlebar Kit on this model motorcycle. Please see the P&A retail catalog or the Parts and Accessories section of for a list of required parts or accessories for this model. For Australia, Brazil, England, Europe and Japan, two special screws (Part Number 2935A) will also be required. Tools and Supplies Required Loctite® 271 Threadlocker and Sealant – Red (H-D Part Number 99671-97) is required for the proper installation of this kit. Fresh, uncontaminated DOT 4 brake fluid from a sealed container will also be needed. Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) For models that retain the original brake line, the two brake- line gaskets found at each banjo fitting must be replaced . Refer to the appropriate parts catalog or see a Harley-Davidson dealer for the correct part numbers. Motorcycles equipped with a glued left-side hand grip will also require a new grip, sold separately. Refer to the parts catalog for replacement stock hand grips. Ask a Harley-Davidson dealer about the selection of Genuine Motor Accessory hand grips that are available. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for this year and model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 6 and Table 1. INSTALLATION Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. Retain all seat mounting hardware. Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTE Immediately wipe up any brake fluid spillage with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills)

Incoming search terms:

HARLEY DAVIDSON BLADE FRONT WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. or FXSTD: Discard tapered spacer. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. 2. See Figure 2. Install valve stem assembly (L) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the machined groove on the hub face is the primary bearing side for all kits except Kits 41681-07 and 40818-08. For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle. • For 2006 and later FXDWG Models: When correctly installed, the tire will be 0.08-0.2 in (2-5 mm) off of center, compared to the fender. • For 2007 and later FX Softail and 2008 and later FXDWG Models: The left side of the wheel is the primary bearing side. • For 2006 and earlier FX Softail and 2007 and earlier FXDWG Models: The right side of the wheel is the primary bearing side. For Kit 40818-08: • Proper installation of this kit requires the separate purchase of two floating brake discs (44343-01 for 2004 – 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel has machined DOT markings to identify it as the primary bearing side. • For 2008 and later Touring: Install bearing shim (43903- 08) under the primary bearing. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. 4. For FLSTC and FLSTN Models: Install wheel kit and right hand wheel spacer provided in installation kit. Refer to FRONT WHEEL in service manual. For FXSTD Models: Install wheel kit, stock wheel spacer and right side wheel spacer provided in installation kit in place of the tapered spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install wheel kit, stock wheel spacers and spacer provided in installation kit between the left side wheel spacer and the left fork. For all other models: Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual. 5. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to verify that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

Incoming search terms: