pms plug location on 04 650 vstar

You search Auto repair manual PDF pms plug location on 04 650 vstar, if there are search results will appear below. If search results do not exist, please search by others keyword.





SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

Single-Cylinder BMW G 650 X Model Series

0

Filed Under (BMW) by admin on 16-11-2010

download
introducing the new range of single-cylinder models, BMW Motorrad is broadening its model line-up with a clear focus on additional target groups. Proceeding from the same technical foundation, the Company has created three new motorcycles absolutely different in their features and characteristics: the G 650 Xchallenge Hard Enduro, G 650 Xmoto Street Moto, and the G 650 Xcountry Scrambler. With their outstanding product substance, their purist looks, and their exceptionally sporting riding characteristics, these single-cylinder models are filling attractive niches in the market. And through their low unladen weight of less than 160 kg or 353 lb according to the DIN standard, they offer dynamic performance for both the connoisseur and the sports-minded rider. Market launch of the new G 650 X model series is planned in good time for the beginning of the season in spring 2007. These new machines with the smallest engines in the BMW model range offer particularly the young and young-at-heart motorcycle rider exactly the right entry into the world of BMW motorcycles, but are not entry-level bikes in the conventional sense of the word: On the contrary, the G 650 Xchallenge Hard Enduro will thrill the customer who wishes to really benefit from the enormous offroad potential of his machine. The G 650 Xmoto Street Moto, in turn, with its very impressive active riding qualities, offers the genuine enthusiast a new dimension in riding pleasure. The G 650 Xcountry Scrambler, finally, stands for carefree riding pleasure and nimble performance both on the road and off the beaten track. Indeed, this unique machine is able to meet all kinds of requirements and offer virtually all riding qualities ranging from city use via country roads and small, winding lanes, all the way to offroad tracks presenting the most challenging requirements. The G 650 Xcountry therefore conveys the classic but relaxed feeling of riding a genuine Scrambler as well as the concept of “wandering” on your motorcycle into today’s world in a most modern style. And last but certainly not least, riding pleasure is guaranteed under all conditions and in every situation, since the G 650 Xcountry offers the same outstanding engine and running gear qualities as its two very sporting “sister models

Incoming search terms:

Honda VT1100 Shadow Guide Plug Patch Repair Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
Find the guide plug.bn The guide plug is shown in the shop manual with the engine removed from the frame and the left crankcase cover removed. (You’ll find this illustration in the “ELECTRIC STARTER/STARTER CLUTCH” chapter in the “STARTER DRIVEN GEAR/STARTER CLUTCH REMOVAL” section.) It’s a little bit harder to find it on the bike. Start by following the yardstick to see where the guide plug is on my bike. To find it on your bike, lie on the ground (or, preferably a mechanics creeper) next to the bike (without the yardstick) and peek under the shift lever and over the frame There it is, just barely visible from the side of the bike. Here’s what a new one looks like: 2. Clean the guide plug and crankcase. From the front of the bike, clean the guide plug and crankcase with brake cleaner in a VERY focused spray. Let the cleaner evaporate before moving to the next step. Page 4 Rev: Draft 5/20/2007 Page 4 of 5 3. Reposition the guide plug. a. From the side of the bike, use the yardstick (or a long screwdriver if you prefer) to gently push the guide plug back into the crankcase. (Note the JB Weld from the previous patch operation.) b. From the front of the bike, gently push upward on the bottom of the upper tab (as shown below) or the bottom of the forward tab to rotate the guide plug into the proper position while maintaining pressure with the yardstick

Incoming search terms:

Yamaha V-Star 650 Jet Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Remove the vacuum slide from the carburetor. • Remove the OEM needle and spacer, noting the order of assembly. • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needle. • Reinstall the OEM spacer and washer. • Reinstall the vacuum slide along with the diaphragm spring. • Reattach the diaphragm cover and tighten its screws. Note: Verify that the slide maintains a full range of movement! • Drain the fuel from float bowl and remove the bowl cover. • Remove the new cap head Allen screws in place of the OEM Phillips head screws. • Repeat above steps for other OEM main jet and pilot jet, and replace them with Baron’s main and pilot jets. • Thoroughly clean the inside of the float bowl prior to reinstalling it. • Reassemble the carburetor by reversing the order of previous steps. Use thecarburetor. • Locate the fuel mixture plug on each carburetor; it will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plug for each carburetor. CAUTION: The fuel mixture screw is located directly beneath this plug. Be prepared to stop the drill and remove the bit the instant you break through the plug. b. Insert a self-tapping sheet metal screw into the drilled hole and remove the plug. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (2) Mikuni main jets, (2) pilot jets, (2) titanium needles, (2) clips, (8) cap head Allen screws Revision 2.0 c. With air/fuel screw now accessible, use a flat blade screwdriver to turn the screw clockwise until it seats, then carefully turn it counter-clockwise 3 turns. Refer to final step for assistance in fine-tuning the setting of the air/fuel adjustment screw. • Reinstall the OEM air filter assembly. • Check all vent lines, fuel lines, and linkage for any obstructions or blockage

Incoming search terms:

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

HARLEY DAVIDSON XL SEAT KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1 2 is 00911 1. Tongue 2. Keyhole Figure 2. Underside of 2-up seat INSTALLATION NOTE If installing the seat with a sissybar/backrest pad present, remove the backrest pad prior to seat installation. This will prevent damage to the pad and/or seat. Reinstall backrest pad after the seat is installed. 1. Models equipped with solo seats: See Figure 1. a. Remove the plastic plug (1) from the rear hole location in the fender (2). Save the plastic plug for installation. b. Move the seat retention nut (4) and lockwasher (5) from the middle location to the rear location, where the plug was just removed. As shown in the inset, a cable strap (6) can be used as an installation aid. Place the retention nut (5) over the cable strap so that the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender, and through the fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. c. With the rib of the retention nut (4) seated into the notch in the fender hole, slide the retension washer (5) into place from the rear. This will lock the retention nut in place. d. Reinstall the plastic plug in the fender hole in the middle location. NOTE The foam cushioning of the seat needs to be compressed as the seat is slid forward to engage the post on the frame when the seat is dropped into place. When properly installed, the front tongue on the underside of the seat should fit snugly in the groove at the fuel tank rear mounting location and the keyhole on the underside of the seat will lock the seat to the post on the frame. 2. All models: See Figure 2. a. Angle the front of the new seat into place so the tongue (1) engages the slot at the rear fuel tank mounting location. b. Push the seat forward and rotate the rear of the seat downward until the seat contacts the frame. Flex the seat slightly in the middle and slide the seat towards the rear so that the keyhole slot (2) on the seat bottom engages with the center seat post on the frame. 3. See Figure 3. Pull up on the center of the seat to verify that it is locked into place. (There will be a small amount of play, but the seat should only come up about a half an inch and then will be held firmly in place by the post on the underside of the seat.) If the seat is not firmly in place, repeat Step 2 until the seat is firmly in place. Reference the Owners Manual for further instruction on seat placement if needed

Incoming search terms:

HARLEY-DAVIDSON Starter Relay Location Guide

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Touring 1998 – 2007 Additional Notes: Relay Location: Under Seat in rubber Boot Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 ***2004 – 2007 FLHR series bikes & 2007 FLHX require additional Adaptor AD-1 & DGD-1. Start Relay is in Power Distribution box. Replaces H-D Relay part# 31579-04 Softails 2000 – 2007 Additional Notes: 2000 is when the Softails changed to Twin Cams. Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Softails 1996 – 1999 Additional Notes: Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05
Dyna 2007 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Replace Batt 15A Fuse with Supplied Fuse Holder Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Tap 12v Fuse (Batt 15A) System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Dyna 2000 – 2005 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Battery connection is made direct to Battery Buss to right of Relay * see Pic3 Installation Notes: Remove Outer Cover, then Remove 4 bolts holding secondary protector plate in place. Relay is on the upper left. Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery Buss + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Pic3 Sportster 2004-2007

Incoming search terms:

BMW F 650 CS Rear belt wheel cracks Removal And Installation Manual

0

Filed Under (BMW) by admin on 12-11-2010

download
Relieve the tension of the toothed belt and lift the belt off the belt wheel (refer to F 650CS Repair Manual, 00.57). 2) Remove 6 screws (see arrow in photo at right). 3) Remove the rear belt wheel. 4) Clean and degrease the tapered bores and the threads of the mounting screws 5) Carefully place the new belt wheel in position on the damper, coat the screw threads with Loctite 243 and hand tighten the securing screws. 6) Tighten the securing screws to the specified torque maintaining a diagonally opposite tightening sequence throughout (Torque to 28 NM, curing time 12 hours). 7) Measure the vertical runout of the belt wheel (refer to F 650 CS Repair Manual, 33.15). 8) Install and adjust the rear drive belt (refer to F 650 CS Repair Manual 00.57 – 00.58) 2.1 Removal of the front belt wheel Remove the front belt wheel in accordance with the instructions detailed in the F 650 CS Repair Manual. Remove the securing screw of the activated charcoal filter and let the filter canister hang by one side by the hoses, or remove it and lay it aside. Clean the splines and threads of the main shaft in order to remove all traces of Loctite. If necessary, remove corrosion from the main shaft spline (use only a brass bristle brush). 2.2 Visual inspection Check the splines of the main shaft for damage. Replace the main shaft if the splines are damaged (broken, chipped, bent or damaged teeth). Refer to the F 650 CS Repair Manual for this procedure.

Incoming search terms:

BMW Motorcycle F 650 GS/ F 800 GS Accessories

0

Filed Under (BMW) by admin on 20-11-2010

download
Stowage-equipment line Vario case, black, left 71 60 7 696 299 £184 / G Vario case, black, right 71 60 7 696 300 £185 / G (+) Case carrier for Vario case, including fasteners 71 60 7 696 301 £144 / G (+) Lock barrel, complete, for 2 cases 51 25 7 688 566 £20.80 / I (o) Lock barrel by code for vehicle and/or case matching locks (order 2x) 51 25 7 681 199 £33.59 (o) Lock-barrel set 51 25 7 698 202 £15.20 / I Liner for Vario case, left 71 60 7 687 610 £67 / I Liner for Vario case, right, and Vario topcase 71 60 7 687 611 £67 / I Vario topcase, black 71 60 7 696 302 £225 / I (+) Luggage rack, large, for Vario topcase (including adapter plate) 71 60 7 696 303 £64 / I (+) Lock barrel for topcase 51 25 7 688 568 £12.50 / I (o) Lock barrel by code for vehicle and/or case matching locks (order 1x) 51 25 7 681 199 £33.60 / I (o) Lock barrels for 2 cases and topcase 51 25 7 688 567 £29.10 / I Liner for Vario case, right, and Vario topcase 71 60 7 687 611 £67 / I Backrest pad for topcase 71 60 7 688 877 £45 / I Luggage carrier, small 71 60 7 701 810 £42.90 / G Tank rucksack, waterproof 71 60 7 711 240 £130 / I Enduro rear softbag 71 60 7 711 245 £35.90 / I Sport softbag, small, 19 l 71 60 7 694 117 £102 / I Sport softbag, large, 51 l 71 60 7 693 567 £139 / I Stuffbag, waterproof, 53 l 72 60 7 653 818 £90 / I Luggage strap with pull-tight buckle 72 60 2 304 808 £6.30 / E Bungee-cord spider 72 60 9 057 579 £3.95 / E Design line Spray-guard extension, rear 71 60 7 695 031 £24.20 / I Sound components Akrapović sports silencer 71 60 7 713 339 *1 £475 / G Ergonomics and comfort line Windscreen, large, tinted 71 60 7 713 834 *1 £138 / I Windscreen, large, clear (standard for F 800 GS) 71 60 7 713 833 £127 / I Windscreen, small, clear (standard for F 650 GS) 71 60 7 713 296 £87 / I Centre stand (F 650 GS) 46 52 7 700 864 *2 £83 / I Centre stand (F 800 GS) 46 52 7 700 049 *2 £91.50 / I (+) Fasteners for centre stand (F 650 GS + F 800 GS) 71 60 7 706 738 £24.90 / I Seat, low, black, 790 mm (F 650 GS), 850 mm ( F 800 GS) 52 53 7 695 013 £174 / I Heated handlebar grips and switches (see electronic parts catalogue) Navigation and communication components BMW Motorrad Navigator III plus 2008 72 60 7 716 116 *1 £650 / I (+) Holder for BMW Motorrad Navigator 71 60 7 697 785 £45.80 / E (+) Securing screw (order 4 of) 32 71 7 652 161 £4.55 / I Connecting cable for BMW Motorrad Navigator 71 60 7 686 670 £55 / E TMC module for BMW Motorrad Navigator 72 60 7 702 687 *1/3 £111 / E Car kit for BMW Motorrad Navigator 72 60 7 703 996 *3 £60.50 / E Navigator carry-bag function 71 60 7 683 161 £49 / I Safety line Hand-protector bar 71 60 7 716 043 £57 / I (+) Countersunk-head screw (order 2 of) 32 71 7 712 836 £3.34 / E Hand protector, small 71 60 7 705 963 £19.50 / I Hand protector, large 71 60 7 715 135 £23.10 / I Protector-mounted spoiler for hand protector, large 71 60 7 705 964 £15.20 / I Crash bar, left 71 60 7 699 437 £104 / I Crash bar, right 71 60 7 699 438 £104 / I (+) Fasteners for crash bar 71 60 7 702 395

Incoming search terms:

Kawasaki Prairie 360,650,700 ATV PLOW Plow Mounting Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Mount Installation Note: There are different hole locations on the plow mount depending on the bike model. For Prairie 360 use the middle hole locations (B), for Prairie 650 and Twin Peaks 700 use hole locations (A) on mounting plate, as shown in Figure 1. Figure 1 Hole Locations WARN INDUSTRIES PAGE 3 67954 Rev A3 To install the plow mount to the underside of the vehicle install the front two U-bolts PN 60869, and loosely tighten the 5/16″ nuts. Pull the plow mount back in the furthest position and then fully tighten, as shown in Figure 2. For the Kawasaki Prairie 360 use the second set of U-bolts PN 61262 and securely tighten around the frame in hole location (B) . For Kawasaki Prairie 650 and Suzuki Twin Peaks 700 drill a 3/8″ hole through the aluminum skid plate, using the plow mount as a template, as shown in Figure 3. Repeat the same process on the other side. After both holes are drilled attach the mounting plate with the second set of U-bolts PN 61262 and securely tighten around the frame in hole location (A) . Tighten all fasteners securely. Torque 5/16″ Bolts: 20ft. lb.

Incoming search terms:

Incoming search terms: