power commander install instructions

You search Auto repair manual PDF power commander install instructions, if there are search results will appear below. If search results do not exist, please search by others keyword.



  power commander install instructions Direct Download speed 5282 Kb/s

  power commander install instructions Full Version speed 6162 Kb/s



1999-2001 EFI Harley Davidson Twin Cam 88 Power Commander IIIr Installation Instructions

0

Filed Under (Harley Davidson) by admin on 30-10-2010

download
1 Remove the seat. 2 Remove saddlebags if installed. 3 Remove left and right side covers. 4 Remove the battery (negative terminal first). 5 Loosen the two 7/16 nuts that retain the ECU (Fig. A) 6 From the left side (underneath the left side cover area) feed the PC III connectors in front of battery tray, and out the right side (in front of the ECU bracket)( Fig. B). 7 Attach PC III module to battery box. First, clean the PCII and battery box with the supplied alcohol wipe. Using the supplied velcro attach PCIII to the battery box. Also secure the unit with the included zip ties. If your bike has cruise control, attach the unit to the face of the cruise control module (Fig. C). 8 Disconnect the large connector from the ECU. Remove the rubber dust shield. 9 Install the dust shield onto the matching connector on the PC III. Zip tie the rubber dust shield to the PC III connector with zip tie provided. 10 Plug the PC III connector into the stock ECU. 11 Plug stock connector into the remaining connector fromthe PCIII(Fig. D). 12 Tighten the two 7/16 nuts that retain the ECU. 13 Route the connectors alongside the ECU and install the right side cover. 14 Replace the battery, the left side cover and the seat. 8 5 Adjusting Your Power Commander Your Power Commander has been programmed with a base map for your application. You can adjust the base map or install an alternate map using your Computer. Please refer to the supplied CD-Rom for more information. You can also adjust your Power Commander using the face plate buttons as described below. 1. With the ignition off, hold down all three buttons on the Power Commander II unit. 2. While still holding down the buttons, turn the ignition on. 3. Release buttons. 4. Select the range you wish to adjust: Low, Med, High, by pushing the corresponding button once. 5. At this point holding that button down will move the lights down ( leaning out the mixture). 6. Pushing the button repeatedly will move the light up (richening the mixture). 7. When the two center light are lit up this is the “0″ setting. After making your adjustments wait 20 seconds before starting the bike or turning it off. This allows the settings to be saved to memory. To verify that it is safe to start the bike, move the throttle and watch to see if the lights move up and down the scale. If they do, you may start or turn off the bike

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

1997-1998 EFI Harley Davidson 1340 EVO Power Commander Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-03-2012

download
1 Remove the seat. 2 Remove saddlebags if installed. 3 Remove left and right side covers. 4 Remove the battery (negative terminal first). 5 Loosen the two 7/16 nuts that retain the ECU (Fig. A) 6 From the left side (underneath the left side cover area) feed the PC III connectors in front of battery tray, and out the right side (in front of the ECU bracket)(Fig. B). 7 Attach PC II module to battery box. First, clean the PCIII and battery box with the supplied alcohol wipe. Using the supplied velcro attach PCIII to the battery box. Also secure the unit with the included zip ties. If your bike has cruise control, attach the unit to the face of the cruise control module (Fig. C). 8 Disconnect the large connector from the ECU. Remove the rubber dust shield. 9 Install the dust shield onto the matching connector on the PCIII. Zip tie the rubber dust shield to the PCIII connector with zip tie provided. 10 Plug the PCIII connector into the stock ECU. 11 Plug stock connector into the remaining connector from the PCIII (Fig. D). 12 Tighten the two 7/16 nuts that retain the ECU. 13 Route the connectors alongside the ECU and install the right side cover. 14 Replace the battery, the left side cover and the seat. 8 5 Power Commander Connnector Stock Connnector Fig.D Fig.E Adjust Idle Speed here Fig.F Adjusting Your Power Commander Your Power Commander has been programmed with a base map for your application. You can adjust the base map or install an alternate map using your Computer. Please refer to the supplied CD-Rom for more information. You can also adjust your Power Commander using the face plate buttons as described below. 1. With the ignition off, hold down all three buttons on the Power Commander unit. 2. While still holding down the buttons, turn the ignition on. 3. Release buttons

Incoming search terms:

2002 Honda VFR 800 VTEC Power Commander 111-210 Installation Instructions

0

Filed Under (Honda) by admin on 26-11-2011

download
If you feel that you are having any problems at all with the Power Commander II, disconnect it from your motorcycle. This will allow the motorcycle to run directly off of the stock ECU. The lights don’t come on when I turn the ignition switch on.
Check to make sure connectors are seated and the kill switch is in the “run” position. The on-board adjustment buttons do not hold their settings. Be sure to wait 20-30 seconds after making adjustments before starting or turning off the bike.
Can not upload to or download from the Power Commander II. Check to see that the serial cable is firmly in place. Verify that ignition switch is on and the kill switch is in the “run” position. My mouse uses the same serial port. If your computer has a PS/2 port purchase a DB9 to PS/2 adapter for your mouse. I get a “verify failed….” message when I upload a map to the Power Commander II. Programs running in the background or fluctuations in supply voltage (from outlet) can sometimes cause this error. In most cases, the information was sent properly to the Power Commander II. Pushing
the “upload all” button again should produce a “tables sent and verified” message. I typed in notes, but they didn’t save.
You need to first push the “accept” button in the notes window and then the “save file” button.

Incoming search terms:

2000-2001 Kawasaki ZX-12R Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove the passenger seat or solo seat cover section. 2) Remove the main seat. 3) Remove the fuel tank shell and prop the front of the fuel tank up. 4) Disconnect the fuel injector connector shown in Fig. A. This connector is located on the backside of the frame towards the bottom of the fuel tank. There are two connectors side by side, disconnect the one on the left. 5) Plug the connectors from the Power Commander in line of these connectors. (Fig. B) 6) Disconnect the rear brake light connector. (Fig. C) Plug the connectors from the Power Commander in line of these connectors. (Fig. D). 7) Connect the ground wire from the Power Commander to the negative side of the battery (Fig. E). 8) Mount the Power Commander in the rear trunk area using the supplied velcro strips. 9) Reinstall the fuel tank and its shell. 10) Reinstall main seat and passenger seat/solo cover

2008 KTM Model Engine Oil Recommendation Chart

0

Filed Under (KTM) by admin on 24-11-2010

download
2008 Model Type Recommended Engine Oil Type Quantity SPORTMINICYCLES AC 50 SX MINI Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L SPORTMINICYCLES LC 50 SX JUNIOR Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 50 SX Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 65 SX Motorex Top Speed 4T 15W50 0.5L SX 2 STROKE 85 SX Motorex Top Speed 4T 15W50 0.5 L 105 SX Motorex Top Speed 4T 15W50 0.5 L 125 SX Motorex Top Speed 4T 15W50 0.7 L 144 SX Motorex Top Speed 4T 15W50 0.7 L 250 SX Motorex Top Speed 4T 15W50 0.7 L SX 4 STROKE 250 SX-F Motorex Power Synt 4T 10W50 1.1 L 450 SX-F Motorex Power Synt 4T 10W50 1.35 L 505 SX-F Motorex Power Synt 4T 10W50 1.35 L CROSS COUNTRY 2 STROKE 65 XC Motorex Top Speed 4T 15W50 0.5L 85 XC Motorex Top Speed 4T 15W50 0.5L 105 XC Motorex Top Speed 4T 15W50 0.5 L 200 XC Motorex Top Speed 4T 15W50 0.7 L
200 XC-W Motorex Top Speed 4T 15W50 0.7 L 250 XC Motorex Top Speed 4T 15W50 0.7 L 250 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L 300 XC Motorex Top Speed 4T 15W50 0.7 L 300 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L CROSS COUNTRY 4 STROKE 250 XC-F Motorex Power Synt 4T 10W50 1.1 L 250 XC-F-W Motorex Power Synt 4T 10W50 1.1 L 450 XC-F Motorex Power Synt 4T 10W50 1.35 L 450 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 505 XC-F Motorex Power Synt 4T 10W50 1.35 L 530 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L ENDURO RACING 450 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 530 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L SUPERMOTO LC4 690 Supermoto Motorex Power Synt 4T 10W60 Approx. 2.0 L SPORT ATV 450 XC Motorex Power Synt 4T 10W50 2.0 L 525 XC Motorex Power Synt 4T 10W50 2.0 L LC8 950 Super Enduro (R) Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure S Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke R Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

CYCLE SOUNDS T-TAP POWER HARNESS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 21-04-2012

download
This t-tap plug is designed to work with Cycle Sounds audio systems. However it can be used to wire many add on 12 volt accessories to you Harley Davidson motorcycle. This plug is rated for 6-8 amps of power and should not be used for adding any product that is rated for more than the t-tap plug is rated for. Take the time to check the products power rating for which you want to install to make sure it is compatible with the t-taps amperage rating. Failure to do so couldlead to electrical failures, which could result in serious injuries or even death. it is possible to overload your motorcycles charging system by adding too many electrical accessories. U se amp meter to verify all power connections. Also check product power ratings for anything you are trying to install. Exceeding the maximum amperage can lead to electrical failures, which could result in serious injuries or even death. INSTRUCTIONS: Step 1: remove seat on bike and locate the wire harness under the seat that matches the plugs on the t-tap harness (2120-0026.) Location may vary between bike models. Step 2: unplug bike harness and snap each end of t-tap harness in correct plug opening. When finished connect power wires to the male plug.(all Cycle Sounds audio systems come pre wired with correct wire colors and terminals). When using this t-tap for any other 12 volt accessory, make sure the red and black wires are snapped into their proper pin connectors. Kit does not come with power terminals for the accessories device. See your local bike dealer for purchase of terminals

HONDA GL1100 AM/FM RADIO INSTALLATION MANUAL/ WIRING DIAGRAM

0

Filed Under (Honda) by admin on 22-04-2011

download
INSTALLATION ■ Outline Procedures This section gives general information needed for mounting the individual radio components on and in the fairing. A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts. 3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing. 7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wires. 3 of 11 Page 4 C) Fairing instllation 1) Install fairing on motorcycle. 2) Connect motorcycle wire harness 9-P coupler to fairing wire 9-P coupler. 3) Connect radio switch wire to switch sub- wire.4) Connect antenna feeder. 5) Confirm that radio operates properly. Reinstall parts removed in step 2 or (A) and in step 1 of (B). REWORKING ■ Remove Fairing and Fairing Parts (Fig.10) 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove right and left fairing pockets, right and left turn signal lenses, right and left nutplates, left hole cover and indi- cator base panel from fairing. (Fig.10) Fig. 10 LEI-1 NU I PLATE 4 of 11■ Reworking on Fairing — Speaker mounting holes- 1) Remove 18 mm grommet. 2) Lightly roll template so that it will follow contour of fairing snugly. 3) Position template on fairing with its upper and outer edges aligned with those offairing as indicated by arrows. 4) Attach template to fairing using adhesive tape where shown. 5) Punch mark centers of four holes with a
drift and hammer. 6) Drill 6 mm holes through marked centers. To obtain a more balanced response with richer, deeper bases, drill two 50 mm holes in the fairing so as to link the speaker box with the inside of the fairing. Fig. 11-1
—Power amplifier mounting holes- 7) Drill two 5.5 mm holes through concaves in fairing. Fig. 11-2 RIGHT HAND SHOWN, LEFT SIMILAR ADHESIVE TAPE

Incoming search terms:

Harley Davidson Road Rod Saddle Bag System Kit INSTALLATION Instructions

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
Use locktite on all fasteners!! 2. Put bike on lift and place jack under frame. Raise bike to lift rear wheel. 3. If swing arm pivot shaft is drilled and tapped on each end, they need to be redrilled and tapped to 3/8-16 to a depth of _” deep. If you are unable to drill & tap your swing arm pivot shaft, you can purchase one from Cycle Visions (part #CV6121), See Harley Davidson® V-Rod® Service Manual Section 2, Page 2.89 for removal and installation instructions. 4. Remove seat, passenger seat, turn signal module, rear fender cover, turn signal license plate assembly, and rear foot peg assemblies. NOTE: Our bag system will not work with stock exhaust system… we recommend the 2-into-1 Supertrap, or you may use any exhaust system that is lower than the rear axle bolt. 5. Remove the two upper shock bolts. Relocate the shock spacer from the right side to the left side, and use the new spacer supplied on the right side. 6. Install front bag mount between frame and spacer (see Figure 1), reinstall shock bolts and torque to 31-50 lbs. 7. Install lower bag support frame to swing arm pivot shaft using the 3/8″ bolt through rear foot peg clevis and cover (see in Figure 2). NOTE: There is a right and left covers and bag support, install accordingly. Torque to 35 foot lbs. 8. Install rear fender front mounting tabs using 8mm 1.25 x _ and flat washers (supplied in kit) (see Figure 3). 9. Install upright saddlebag support brackets to the lower bag mount assembly and lower fender extension crossover mount. (see Figure 4). Torque to 25 lbs. NOTE: Install crossover mount with gusset facing down. 10. Remove license plate light from your rear turn signal bracket license plate assembly. Install license plate light on our license plate light bracket (see Figure 5). 11. Install the license plate bracket on the inside of the rear fender extension using the top holes of the license plate frame (see Figure 6 & 7). 12. Install fender washers on the inside of the fender extension (see Figure 8). 13. Install upper fender bracket to rear fender extension with a _-20 bolt supplied in kit (see Figure 9). 14. Install rear fender extension with chrome button fitted bolts. (see Figure 10 & 11). 15. To check alignment and fit of rear fender extension reinstall original rear fender. Once you have everything lined up and fitted, remove original rear fender, drill & tap (2) two 5/16 x 18 holes in rear fender support bracket (see Figure 12). 16. Install Harley Davidson® Part #70909-95 and 47449-97 bracket and receptacle on front and rear bag supports (see Figure 13 & 14). 17. Install Harley Davidson® Part #47449-97 bracket with receptable (see Figure 14). Make sure the bolts come from the inside out. This bracket is adjustable for location.

Incoming search terms:

Incoming search terms: