pulsar honda electric diagram pdf file download

You search Auto repair manual PDF pulsar honda electric diagram pdf file download, if there are search results will appear below. If search results do not exist, please search by others keyword.



  pulsar honda electric diagram pdf file download Direct Download speed 5282 Kb/s

  pulsar honda electric diagram pdf file download Full Version speed 6162 Kb/s



Pulsar XR 650R ELECTRIC-START KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Pulsar) by admin on 27-10-2010

download
1. Remove the seat, fuel tank, side panels, muffler, and headers. 2. Disconnect the stator wires from their corresponding mates underneath the seat (trace the wires up from the left side case.) Un-route the stator wiring so it hangs free from the left side case. 3. Remove the stock shift lever and the left side engine case cover. You do not need to drain the oil from the engine. 4. Unbolt and remove the stator and wiring from the stock cover. Do not cut any wires. 5. The stock pulsar coil (small black box hanging from the stator) will have to be modified slightly to clear the ring gear before installation into the new cover. Remove (file or grind) about .030 inches of material from the base of the pulsar coil so that the base is flush with the face of the rest of the coil as shown in Photos 1 and 2. File Here Photo 2 Make flush with this surface Remove material here Photo 1 6. Install the stator and modified pulsar coil into the new engine case cover as shown in Photo 3. Use the three provided Phillips head bolts, split lock-washers, and plastic cable clamps to secure the wiring as shown. You will need to pull about ½” of extra wire through the grommet (Photo 4) to give you enough wire length for the grommet to sit in its case cutout. To do this, remove the electrical tape from the end of the stator wires and pull each wire individually through the grommet. Neither of the stock metal wire guides will be used when reinstalling the stator into the new case (Photo 5). 5/16″ cable clamps 1/8″ cable clamp Photo 3 Photo 5 Not Used Pull extra wire through grommet Photo 4 7. Remove the stock flywheel nut (An air impact tool works best to remove this nut without turning the motor). Remove the flywheel using the flywheel puller provided. 8. Locate the T and F marks on the stock flywheel (Photo 6). The T mark is used to adjust valve clearances and its location needs to be transferred to the ring gear. Scribe a line in the edge of the flywheel in line with the T mark as shown in Photo 7

Incoming search terms:

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

Honda Foreman 500 And Honda Rubicon WINCH MOUNTING KIT INSTALLATION

0

Filed Under (Honda) by admin on 13-12-2011

download
Begin by removing the front skid plate located on the front of the ATV. Remove the four side 8mm bolts and four bottom 6mm bolts securing the front skid plate, figure 1. Save the fasteners as they will be used later to reinstall the front skid plate. 2. Remove the four plastic rivets on each side of the front plastic fascia, figure 2. Use a large screw driver to carefully remove the center rivet. After removing the center rivet, remove the rivet housing. Save the fasteners as they will be used to reinstall the front plastic fascia. 3. Remove the two 6mm bolts that attach the front plastic fascia to the bumper, figure 3. Remove the front plastic fascia at this time . Remove the two 6mm bolts that attach the front bumper to the plastic headlight assembly, figure 4. Save the fasteners as they will be used to reinstall the front bumper. 5. Remove the two top 8mm bumper bolts that attach the front bumper to the front rack, figure 5. Save the fasteners as they will be used to reinstall the front bumper. Figure 5 Remove Top Bumper Bolts Remove (both sides) 6. Remove the two ottom bumper bolts that attach the bumper to the bottom of the vehicle frame, figure 6. Save the fasteners as they will be used to reinstall the front bumper

Incoming search terms:

HONDA VTX1800R AND HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM REMOVAL

0

Filed Under (Honda) by admin on 17-11-2011

download
If motorcycle is oxygen sensor equipped, unscrew the sensors from the stock exhaust system and install them
into the Vance & Hines exhaust system, being sure to install the front cylinder sensor into the lower pipe and
the rear cylinder sensor into the top pipe. Note: Use caution when handling. Do not touch sensor tip area.
2. If motorcycle is not oxygen sensor equipped, install both M12 x 11 plugs and washers (supplied)into the oxygen
sensor bosses. 3. Check condition of stock exhaust gaskets. Replace if damaged or worn. 4. Install and tighten supplied mounting bracket (stamped 345-P) in the original mounting bar location, using one M10 x 35 flange bolt and nut on top (supplied) and one M10 x 20 flange bolt on bottom (supplied) (Figure 2). Note: The bracket mounts behind the top frame mount and in front of the bottom frame mount(Figure 2).5. Install and tighten rectifier using M6x30 flange bolt, nut
and washer combinations (supplied) (Figure 2). 6. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker mark outside surface of front and rear heat shields with location of the mounting clips welded to the inside

Incoming search terms:

1997 Honda CBR 1000 F specifications review

0

Filed Under (Honda) by admin on 20-12-2011

download
Front brakes: Dual disc Rear brakes: Single disc Speed and acceleration Top speed: 255.0 km/h (158.4 mph) Power/weight ratio: 0.5745 HP/kg Other specifications Further information Parts and accessories Check out parts and accessories from our partners. Ask questions Join the 97 Honda CBR 1000 F discussion group Insurance, loans, tests Search the web for dealers, loan and insurance costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs Buying a bike starts at Bikez Get a list of related motorbikes before you buy this Honda. Inspect technical data. Look at photos. Read the riders’ comments at the bike’s discussion group. And check out the bike’s reliability, repair costs, etc. Show any 1997 Honda CBR 1000 F for sale on our Bikez.biz Motorcycle Classifieds. You can also sign up for e-mail notification when such bikes are advertised in the future. And advertise your old MC for sale. Our efficient ads are free. You are also welcome to read and submit motorcycle reviews. Rating sample for this Honda bike Value for money for the 1997 Honda CBR 1000 F: (67.1 out of 100) Click here for complete rating. You can also compare bikes.

Incoming search terms:

HONDA VTX1800R & HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM

0

Filed Under (Honda) by admin on 10-11-2011

download
harness. Remove wire tie (take note of harness routing for reassembly). Un-route wires and drape over right side of pipe. 3. Remove entire right side floorboard assembly, (three bolts) (Figure 1). 4. Remove exhaust port flange nuts.
5. Remove flange bolts securing rear muffler mount to exhaust system mounting bar. 6. Remove complete exhaust system. Start by removing front head pipe from exhaust port (assistance may be required). 7. Remove rectifier from mounting bar. 8. Remove stock (cast iron) exhaust system mounting bar.

HONDA GL1100 AM/FM RADIO INSTALLATION MANUAL/ WIRING DIAGRAM

0

Filed Under (Honda) by admin on 22-04-2011

download
INSTALLATION ■ Outline Procedures This section gives general information needed for mounting the individual radio components on and in the fairing. A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts. 3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing. 7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wires. 3 of 11 Page 4 C) Fairing instllation 1) Install fairing on motorcycle. 2) Connect motorcycle wire harness 9-P coupler to fairing wire 9-P coupler. 3) Connect radio switch wire to switch sub- wire.4) Connect antenna feeder. 5) Confirm that radio operates properly. Reinstall parts removed in step 2 or (A) and in step 1 of (B). REWORKING ■ Remove Fairing and Fairing Parts (Fig.10) 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove right and left fairing pockets, right and left turn signal lenses, right and left nutplates, left hole cover and indi- cator base panel from fairing. (Fig.10) Fig. 10 LEI-1 NU I PLATE 4 of 11■ Reworking on Fairing — Speaker mounting holes- 1) Remove 18 mm grommet. 2) Lightly roll template so that it will follow contour of fairing snugly. 3) Position template on fairing with its upper and outer edges aligned with those offairing as indicated by arrows. 4) Attach template to fairing using adhesive tape where shown. 5) Punch mark centers of four holes with a
drift and hammer. 6) Drill 6 mm holes through marked centers. To obtain a more balanced response with richer, deeper bases, drill two 50 mm holes in the fairing so as to link the speaker box with the inside of the fairing. Fig. 11-1
—Power amplifier mounting holes- 7) Drill two 5.5 mm holes through concaves in fairing. Fig. 11-2 RIGHT HAND SHOWN, LEFT SIMILAR ADHESIVE TAPE

Incoming search terms:

HONDA TRX 650 RINCON 4X4, TRX 680 Rincon BLADE HARDWARE MOUNTING REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Honda) by admin on 26-12-2011

download
Push tube/ Swivel/ Blade Assembly Instructions 1. Install the blade swivel (15) onto the front of the push tube (14) using the 1/2″ shoulder bolt (4), two 1/2″ washers (5), and a 3/8″ Nylock nut (3) from the bolt bag per diagram #1. Make sure the flat washers seat properly on the bottom of the shoulder bolt while tightening the nut. Make sure the blade turns freely. 2. Remove the 2 bottom flanged nuts (I) from the u-bolt (D) and 2 from the 3/8″ bolts (H) on the blade position pin assembly (23). Run the 2 top flanged nuts up the threads of the u-bolt. Place the blade position pin assembly on the push tube as shown in the Diagram, sliding the blade position pin through one of the oval holes on the swivel and through the rear blade position pin support bracket on the push tube. 3. Re-install the u-bolt and 3/8″ bolts and flanged nuts per the Diagram. On the u-bolt, thread the bottom nuts up until they are flush with the bottom of the threads then run the top ones down, making sure the bottom nuts remain flush with the bottom of the u-bolt. Tighten all 4 bottom nuts. 4. Remove the two shoulder bolts (18) from the pivot point brackets on the back of the blade (1). Attach the blade to the swivel by sliding the ears on each side of the swivel into the pivot point brackets on the blade, reinstall the two shoulder bolts and Nylock nut (3) and tighten. 5. Hook the blade springs (6) to the two round holes on either side of the 5 oval holes on the swivel. Hook the eyebolts through the other end of the springs, push the eyebolts through the spring attaching points on the back of the blade and install 3/8″ Nylock nuts (3). Spring tension may be increased by tightening both Nylock nuts on the eyebolts evenly. 6. Install the blade stops (16) with the two 3/8″ x 1″ bolts (17) and 3/8″ nuts (3) per the Diagram. Rotating the stops allows you to change the blade pitch to suit changing conditions or materials

Incoming search terms:

HONDA GL1500CD/ VALKYRIE Specifications

0

Filed Under (Honda) by admin on 29-01-2011

download
position when it comes to the environment. We continue to develop low-emission technologies for our current and future motorcycles, ATVs, scooters and personal watercraft. We already produce models that exceed the stringent 2008 CARB emissions requirements years ahead of schedule. And that’s the kind of performance everybody can appreciate. BE A RESPONSIBLE RIDER. Riding a motorcycle is an exercise in responsibility—to yourself, to others, to the environment and to the sport. So remember, wear a helmet, eye protection and protective clothing whenever you ride. Never ride under the influence of drugs or alcohol, and never use the street as a racetrack. Inspect your motorcycle before riding, read your owner’s manual, and see your local Honda Dealer concerning reimbursement through the Honda Rider’s Club of America™for Motorcycle Safety Foundation (MSF) rider training.* Always obey local laws, use common sense, and respect the rights of others when you ride. Make sure you have a proper license when riding on public roads, and never modify your motorcycle’s exhaust system. 03 SPECIFICATIONS ACCESSORIES VALKYRIE Log on to our website at honda.com for more information about Honda Genuine Accessories . On a bike like the Valkyrie, you can never have too much chrome. And that’s precisely why we offer our Chrome Sidecovers and Chrome Swingarm-Pivot cover to help really brighten up these areas. Here’s one of our most popular Valkyrie accessory options. These Leather Saddlebags look great, hold plenty, and match some of the other leather accessories we have available. Got a long trip planned, or is winter right around the corner? Then make sure you take a look at-or should we say take a look through-a Honda Genuine Accessories Windshield for your new Valkyrie. GL1500CD 1520cc liquid-cooled horizontally opposed six-cylinder with belt-driven overhead camshafts Six 28mm constant-velocity carburetors 71.0 x 64.0mm Solid-state digital Five-speed constant-mesh Shaft 150/80R-17 radial 180/70R-16 radial Dual-disc with twin-piston calipers 28.9 inches 66.5 inches 5.3 gallons, including 1.1 gallon reserve 681 pounds Black Windshield, leather saddlebags, chrome exhaust tips, chrome rear carrier, CB transceiver kit, passenger CB talk switch, studded backrest pad, studded main seat, studded rear seat, deluxe backrest pad

Incoming search terms:

1997 Honda CBR 1000 F specifications

0

Filed Under (Honda) by admin on 03-11-2010

download
Front brakes: Dual disc Rear brakes: Single disc Speed and acceleration Top speed: 255.0 km/h (158.4 mph) Power/weight ratio: 0.5745 HP/kg Other specifications Further information Parts and accessories Check out parts and accessories from our partners. Ask questions Join the 97 Honda CBR 1000 F discussion group Insurance, loans, tests Search the web for dealers, loan and insurance costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs Buying a bike starts at Bikez Get a list of related motorbikes before you buy this Honda. Inspect technical data. Look at photos. Read the riders’ comments at the bike’s discussion group. And check out the bike’s reliability, repair costs, etc. Show any 1997 Honda CBR 1000 F for sale on our Bikez.biz Motorcycle Classifieds. You can also sign up for e-mail notification when such bikes are advertised in the future. And advertise your old MC for sale. Our efficient ads are free. You are also welcome to read and submit motorcycle reviews. Rating sample for this Honda bike Value for money for the 1997 Honda CBR 1000 F: (67.1 out of 100) Click here for complete rating. You can also compare bikes. Pictures, trademarks and logos of third parties are exclusive property of the respective owners. Technical specifications are subject to change without notice. Bikez.com has been developed by low-cost software development company ObjectLabs

Incoming search terms:

Incoming search terms: