pumps mail

You search Auto repair manual PDF pumps mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





YAMAHA Road Star Fuel Pump Relocation Kit INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove seat and disconnect battery. Remove fuel tank along with both left and right side battery covers, and remove air box from carburetor (all per Yamaha standard shop manual procedures). 2. Remove chrome plastic cover over fuel pump and disconnect choke cable/knob from lower pump bracket. Remove pump-to-carb fuel line from fuel pump. Disconnect fuel pumps electrical lead connector. 3. Remove two (2) hex-head pump mounting bracket bolts and remove pump assembly from motorcycle. Slide fuel pump up and off bracket mounting posts (Caution: excess fuel may drain from pump and/or fuel lines and fuel filter!). Remove heat shield. Remove remaining fuel line from pump. Pull all fuel lines from filter and remove steel springs and hose clamps from these lines (these will be reused on the kits fuel lines). With a sharp knife or box cutter, trim off the top portion of the fuel pumps rubber isolation/mount system per Photo A. Next cut pumps wiring harness approximately half way between connector and pump. Strip the insulation from the ends of these wires as well as from the supplied Baron harness extension wires. Using the supplied electrical butt connectors, crimp Baron harness extensions red wire to pumps black-w/blue-strip wire, and Baron harness extensions black wire to pumps black wire. Repeat this process on other side of wire harness extension with pumps connector. Now, referring to Photo B, you will need to cut off the square tube that runs along the side of the fuel pump with a hack saw. Cut down toward pump body in a straight cut, then cut tube off by cutting along the body. This will allow you to twist pump in the rubber mount so the curved spigot is facing up (clockwise approx 1/4 turn). 4. Remove pump-to-carb fuel line from carb and separate electrical wires from this line. Remove this fuel line from engine. Re-route choke cable to right side of engine (toward carb) and rotate it up and over rear cylinder head back toward left side of bike. Mount new Baron choke bracket to the choke cable and tighten plastic nut. New choke bracket will mount to rear fuel tank mounting location (Photo C). 5. 99~03 models – Remove electrical relay bracket (found under the right side cover) from the bike and slide each relay off of this bracket. Install fuel pump onto new Baron Fuel Pump Bracket and install bracket in the same location as the stock bracket you just removed, using stock mounting hardware. Refer to Photo F for proper installation. 6. 04~07 models Remove electrical relays from stock bracket and remove relays from rubber holder. Cut rubber holder per Photo E and replace one of the relays into the rubber and install on to new Baron bracket. The second relay will be placed to the right of the tool bag under the seat and secured with the provided two-sided tape pad. Reconnect plugs to the relays. (Photo F)

Incoming search terms:

1999-2002 SUZUKI SV 650 OWNER'S MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FUEL, ENGINE OIL AND COOLANT RECOMMENDATION FUEL Your motorcycle requires regular unleaded gasoline with a minimum pump octane rating of 87 ((R+M)/2 method) . In some areas,the only fuels that are available are oxygenated fuels. Oxygenated fuels which meet the minimum octane requirement and the requirements described below may be used in your motorcycle without jeopardizing the New Vehicle Limited Warranty or the Emission Control System War- ranty. NOTE: Oxygenated fuels are fuels which contain oxygen-carrying additives such as MTBE or alcohol. Gasoline Containing MTBE Unleaded gasoline containing MTBE (Methyl Tertiary Butyl Ether) may be used in your motorcycle if the MTBE content is not greater than 15%. This oxygenated fuel does not contain alcohol. Gasoline/Ethanol Blends Blends of unleaded gasoline and ethanol (grain alcohol), also known as GASOHOL, may be used in your vehicle if the ethanol content is not greater than 10%. Gasoline/Methanol Blends Fuels containing 5% or less methanol (wood alcohol) may be suitable for use in your motorcycle if they contain co-solvents and corrosion inhibitors. DO NOT USE fuels containing more than 5% methanol under any circumstances. Fuel system damage or motorcycle performance problems resulting from the use of such fuels are not the responsibility of Suzuki and may not be covered under the New Vehicle Limited Warranty or the Emission Control System Warranty . Fuel Pump Labeling In some states, pumps that dispense oxygenated fuels are required to be labeled for the type and percentage of oxygenate, and whether important additives are present . Such labels may provide enough information for you to determine if a particular blend of fuel meets the requirements listed above. In other states, pumps may not be clearly labeled as to the content or type of oxygenate and ad- ditives . If you are not sure that the fuel you intend to use meets these requirements, check with the service station operator or the fuel suppliers

Incoming search terms:

1999-2002 SUZUKI SV650 OWNER'S MANUAL

0

Filed Under (Suzuki) by admin on 12-12-2010

download
Gasoline/Ethanol Blends Blends of unleaded gasoline and ethanol (grain alcohol), also known as GASOHOL, may be used in your vehicle if the ethanol content is not greater than 10%. Gasoline/Methanol Blends Fuels containing 5% or less methanol (wood alcohol) may be suitable for use in your motorcycle if they contain co-solvents and corrosion inhibitors. DO NOT USE fuels containing more than 5% methanol under any circumstances. Fuel system damage or motorcycle performance problems resulting from the use of such fuels are not the responsibility of Suzuki and may not be covered under the New Vehicle Limited Warranty or the Emission Control System Warranty . Fuel Pump Labeling In some states, pumps that dispense oxygenated fuels are required to be labeled for the type and percentage of oxygenate, and whether important additives are present . Such labels may provide enough information for you to determine if a particular blend of fuel meets the requirements listed above. In other states, pumps may not be clearly labeled as to the content or type of oxygenate and ad- ditives . If you are not sure that the fuel you intend to use meets these requirements, check with the service station operator or the fuel suppliers. d of. ; NOTE: • * To help clean the air, Suzuki recommends that you use the oxygenated fuels . • * Be sure that any oxygenated fuel you use has octane ratings of at least 87 pump octane ((R+M)/2 method) . • * If you are not satisfied with the driveablity or fuel economy of your motorcycle when you are using an oxygenated fuel, you should switch back to regular unleaded gasoline . • * If engine pinging is experienced, substitute another brand as there are differences between brands . A CAUTION Spilled gasoline containing alcohol can harm your motorcycle. Alcohol can damage painted surfaces. Be careful not to spill any fluid when filling the fue

2004 KTM 950 ADVENTURE REPAIR MANUAL

0

Filed Under (KTM) by admin on 23-11-2010

download
Intake system Fresh air is drawn into the filter box through the intake snorkel 1 , past the carburetors 2 and through the air filter 3 . The cleaned air is conducted to the combustion chamber through the carburetors and intake ports. 1 2 2 3 2-4 Repair manual KTM LC8 Art.-Nr . 3.206.016-E Secondary air system The secondary air system supplies fresh air to the emissions in the exhaust port, resulting in the afterburning (oxidation) of the emissions. A line leads from the filter box 1 to the control valve 2 which opens as soon as the throttle valves 3 are opened. The line continues to the reed valves 4 in the cylinder heads which are actuated by the pressure pulsation in the exhaust system. As a result, cleansed fresh air arrives in the exhaust port. The oxygen content in the air and the high exhaust gas temperature cause the emissions to oxidize. If the throttle valves are closed and the engine goes into an overrun condition, the underpressure in the intake port will rise and the control valve will close. This prevents exhaust backfire (combustion of the unburned fuel/air mixture). 1 2 3 3 4 4 4 2-5 Closed thermostat The thermostat is closed if the temperature of the cooling liquid drops below 75°C. The water pump 1 pumps the cooling liquid through the cylinder and cylinder heads 2 and the thermostat 2 . Open thermostat The thermostat 3 opens at 75°C. The water pump 1 pumps the cooling liquid through the cylinder and cylinder heads 2 , the aluminum cooler 4 and the thermostat. The pressure in the cooling system (max. 1.4 bar) is regulated by a valve in the radiator cap 5 . The cooling liquid level in the compensating tank 6 must be between the MIN and MAX marks when the engine is cold. The fan 7 switches on at 102°C.

2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

MOUNTAIN BIKE AIR SHOCK SET-UP AND TUNING GUIDE

0

Filed Under (Tips and Review) by admin on 01-12-2010

download
DETAILED SET-UP 2. Installing Air Pressure – Remove the air cap from the Schrader valve on the end of the shock body. Attach the pump to the Schrader valve. Some people damage their pumps by screwing them on too far. As soon as the gauge registers pressure, screw 1/2 turn more and pump to the desired level. Use the release button on the pump to reduce air pressure. The hiss you hear when unscrewing the pump is only the air from the pump and not from the shock! Likewise, when you install the pump again, you will also hear a hiss as air from the shock fills the pump and reduces the registered pressure you previously installed. All perfectly normal when pressurizing the shock! After removing the pump, be sure to reinstall the Schrader valve cap. If the shock does not dampen properly after pressurizing, the air pressure may have been lost during pump removal as a result of a worn pump fitting o-ring that needs replacement. Do not ride the bike until the shock is properly pressurized. 3. Main Air Spring Pressure Adjustments – Air Spring adjustments are made by inflating or deflating the main air spring chamber. Since your IFP air pressure adjustment (outlined above) also affects your starting spring force, you should always adjust your IFP pressure before adjusting the main air spring pressure. You can refer to the online Quick Start guide at: www.progressivesuspension.com/literature.html for accurate main air spring pressure and sag settings matched to your bike model and body

Incoming search terms:

APRILIA TUONO V4 R APRC Technical specifications

0

Filed Under (Aprilia) by admin on 16-11-2010

Engine type Aprilia longitudinal 65° V-4 cylinder, 4-stroke, liquid cooling system, double overhead camshafts (DOHC), four valves per cylinder Fuel Unleaded petrol Bore and stroke 78 x 52.3 mm Total engine apacity 999.6 cc Compression ratio 13:1 Maximum power at crankshaft 162 hp (119 kW) at 11,000 rpm Maximum torque at crankshaft 110 Nm at 9,000 rpm Fuel system Airbox with front dynamic air intakes. 4 Weber-Marelli 48-mm throttle bodies with 4 injectors and latest generation Ride-by-Wire engine management. Choice of three different engine maps selectable by the rider with bike in motion: T (Track), S (Sport), R (Road) Ignition Magneti Marelli digital electronic ignition system integrated in engine control system, with one spark lug per cylinder and “stick-coil” type coils Starting Electric Exhaust system 4 into 2 into 1 layout, single oxygen sensor, lateral single silencer with engine management system controlled butterfly valve and integrated trivalent catalytic converter (already meets future Euro4 regulations) Alternator Flywheel mounted 420W alternator with rare earth magnets Lubrication Wet sump lubrication system with oil radiator and two oil pumps (lubrication and cooling) Gearbox 6-speed cassette type gearbox 1st: 39/15 (2.600) 2nd: 33/16 (2.063) 3rd: 34/20 (1.700) 4th: 32/22 (1,455) 5th: 34/26 (1,308) 6th: 33/27 (1,222) Gear lever with Aprilia Quick Shift electronic system (AQS)
Clutch Multiplate wet clutch with mechanical slipper system rimary drive Straight cut gears and integrated flexible coupling, drive ratio: 73/44 (1,659) Secondary drive Chain: Drive ratio: 42/16 (2.625) Traction anagement APRC System (Aprilia Performance Ride Control), which includes Traction Control (ATC), Wheelie Control (AWC), Launch Control (ALC), all of which can be configured and deactivated independently. Frame Aluminium dual beam chassis with pressed and cast sheet elements. Sachs steering damper. Front suspension Sachs upside down front fork with Æ 43 mm stanchions. Low profile forged aluminium calliper mountings for radial callipers. Completely adjustable spring preload and hydraulic compression and rebound damping. Wheel travel: 120 mm

Tacoma Power Steering Pump Improving Power Steering Reservoir modification

0

Filed Under (Toyota Manuals) by admin on 02-10-2011

download
For my SAS I decided to add hydraulic steering assist as it comes in real handy for rock crawling. I got the Redneck Ram setup from the folks at West Texas Off-road that includes rebuilding an earlier IFS steering box along with drilling and tapping the box for the included ram. One of the down sides of adding a ram is that it slows the steering down because the stock steering pump has to supply the added volume for the hydraulic ram. Another is that it creates a fluid volume change in the system reservoir that needs to be compensated for in some way. After doing some reading on the West Texas site about how to go about modifying a Saginaw pump and reading up on earlier Toyota pump mods for steering assist setups on the Pirate board, I decided to give it whirl and see what I could do about the Tacoma pump. Chuck Gardella was kind enough to supply me with a blown pump that I could rebuild and submit to my endless fiddling and tinkering. I plan to give him my pump in return when I get this one done and installed. You need to do something to allow for more room in the reservoir for the standard hydraulic ram assist setup so I decided to tackle the reservoir first. The reason you need the extra space is because the ram is unbalanced. That is there is a rod on one side of the cylinder and not on the other side so the volume of the fluid has to change in the system to account for the volume of the rod as it travels back and forth. I calculated the volume of the rod that I have at full stroke to be about 2 oz or so. This would equate to plus or minus up to 2 oz. in the pump reservoir. Well first off, it’s no wonder why so many folks boil their steering pumps over with heavy wheeling and have so many other steering problems. The stock power steering reservoir doesn’t even rate pint sized

Incoming search terms:

BMW Motorcycles F 650 GS Dakar fuel tank replacement

0

Filed Under (BMW) by admin on 12-11-2010

download
Your center has been requested in a recent e-mail, to forward VIN, color Information: and status information on all F 650 GS(A) and Dakar models remaining in your inventory. Fuel tanks, together with the appropriate colored trim pieces, will be forwarded to your center for each bike in your inventory as replacement parts arrive in BMW NA inventory. Warranty Please enter a warranty campaign claim , encompassing the following Reimbursement: Work Package information, when claiming reimbursement for the updates called for in this bulletin. Even though there is no charge for the parts, a sublet of $60.00 will be applied to each claim. This sublet amount is intended as a combination of both the handling and as reimbursement for incidental items that may be required in the replacement of the fuel tank. Work Package #1 is to be used in the replacement of all F 650 GS(A) and Dakar model fuel tanks. Defect Code: 00 00 16 1100 Description: Fuel Tank – Leaking Flat Rate Code: 00 60 059 Description: Remove and reinstall fuel tank (USA only) FRU: 12 FRU Sublet #4: $60.00 Pick up & In the recent Sales and Marketing Bulletin # B23/00 introducing the “Customer Delivery: Demonstration Program”, (e-mailed to your center on September 7, 2000), each BMW motorcycle retailer was asked to arrange to pick up, complete the updates and deliver the motorcycle back to the customer and to offer the use of a demonstrator where appropriate.

Incoming search terms:

Motorcycle Carburetor Rebuilding

0

Filed Under (Tips and Review) by admin on 22-11-2010

download
Experience has shown that when a customer disassembles, it creates a storage issue for us as well as parts are generally missing. The disassembly usually costs us extra hours of work during the rebuild. The only acceptable part to be removed from an assembly is the cable bracket if it is fragile and in danger of breaking during shipping. All other parts should be where they belong. Rebuild Service Prices: If your carburetor type doesn’t appear below or you are not sure, please send a note to our e-mail for pricing details. Military rebates are available to honor our service men and women! Active Duty military, contact us for a rebate. Please include your service, pay grade and current duty station when you contact us.

Incoming search terms: