quick disconnect sidecar brake

You search Auto repair manual PDF quick disconnect sidecar brake, if there are search results will appear below. If search results do not exist, please search by others keyword.



  quick disconnect sidecar brake Direct Download speed 5282 Kb/s

  quick disconnect sidecar brake Full Version speed 6162 Kb/s



HARLEY DAVIDSON XL BRAIDED FRONT BRAKE LINE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
REMOVAL Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1. Drain the brake fluid following the instructions in the service manual. Dispose of waste properly. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Disconnect the battery, negative (-) cable first or remove the main fuse. Follow the instructions in the service manual 3. Remove bolt and two sealing washers to disconnect brake line fitting from master cylinder. Discard sealing washers, but save bolt for installation. 4. Remove bolt and two sealing washers to disconnect brake line fitting from front brake caliper. Discard sealing washers, but save bolt for installation. 5. Carefully make note of brake line routing, then remove existing brake line. NOTE This kit contains clamps and cable straps to either replace the original equipment clamps and cable straps being removed or to add additional brake line support. INSTALLATION Install proper length brake lines. Incorrect brake line length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00325a) Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) Avoid leakage. Be sure gaskets, banjo bolt(s) and brake line are clean and undamaged before assembly. (00323a) 1. Position new sealing washers from kit on each side of hydraulic brake fittings (banjo fittings). Small ID washers are for caliper end, large ID washers are for master cylinder end. 2. Insert bolts (removed earlier) through washers and fittings. 3. Hold new braided brake line in position and install bolts into master cylinder and caliper. Tighten only enough to keep banjo fitting in the same orientation as the stock banjo fitting. 4. Verify there is no twist in the brake line. Adjust brake line if necessary. 5. Install clamps from kit by wrapping clamp around braided brake line at each of the clamp mounting locations. Verify clamps are oriented the same as the stock clamps. Install clamp screws but do not tighten. 6. Check entire length of braided brake line: a. Be sure brake line is not twisted. b. Turn handlebars fully-left and right while checking to make sure brake line does not contact any vehicle components. c. Be sure brake line length between clamps is sufficient. 7. Adjust brake line if necessary. 8. Tighten caliper and master cylinder banjo bolts to 20-25 ft-lbs (27-34 Nm) .

Incoming search terms:

HARLEY DAVIDSON SOFTAIL BRAIDED REAR BRAKE LINE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) Drain Brake Fluid 1. Pop off bleeder nipple cap on the rear brake caliper. 2. Install one end of a length of plastic tubing over the caliper bleeder valve. Place the free end of the tubing into a suitable container. 3. Open the bleeder valve about 1/2-turn and pump the brake pedal to drain the brake fluid out of the rear brake system. Do not reuse brake fluid. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) Remove Existing Rear Brake Line 1. Disconnect wiring harness connectors from brake light switch spade terminals. Avoid leakage. Be sure gaskets, banjo bolt(s) and brake line are clean and undamaged before assembly. (00323a) 2. Disconnect existing brake line from rear brake caliper and rear brake master cylinder assembly. Save banjo bolts, but discard brake line gaskets. NOTE This kit contains all gaskets needed for replacement. 3. Carefully make note of rear brake line routing and orientation of banjo fittings, then remove existing brake line. Save hex head screw holding brake light switch manifold to tab on frame, but discard brake line and attaching parts. 4. Unthread brake light switch from brake line. Save switch for later use.

Incoming search terms:

Harley-Davidson CHROME FRONT BRAKE CALIPER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
See Figure 1. Refer to FRONT BRAKE CALIPERS: REMOVAL in the Service Manual, and follow the instructions to: a. remove the banjo bolt with bleeder valve (2) and both gaskets (4), and b. detach the front brake line (3) from the caliper. c. Discard the gaskets. For this installation, the banjo bolt (2) can also be discarded. d. Remove the caliper mounting bolts (1). Lift the brake caliper assembly upward to remove it from the brake disc. -J03529 1 of 4
2 5 3 4 1 is04104 1. Mounting bolt (2) 2. Banjo bolt with bleeder valve 3. Brake line 4. Gasket (2) 5. Screen cover Figure 1. Remove Existing Caliper 2. Remove the brake pads from the caliper. Refer to BRAKE PADS AND DISCS: BRAKE PAD REPLACEMENT, FRONT BRAKE CALIPER in the Service Manual. a. Remove the screen cover (5) from the caliper. b. See Figure 2. Note the orientation of the brake pads, and remove the retaining clip (2), pad pin (1) and brake pads from the caliper. Also note the position of the brake pads at removal, so they can be installed back in the same location. 3. Repeat the procedure for the opposite-side caliper. 2 1 is04105 1. Pad pin 2. Retaining clip Figure 2. Front Caliper Pad Pin Pad and Pin Inspection 1. Refer to BRAKE PADS AND DISCS: INSPECTION in the Service Manual, and follow the instructions given to inspect the brake pads. If any front brake pad is worn to 0.5 mm (0.020 inch) or less above the backing plate, replace all four front pads. 2. Inspect the brake disc thickness, lateral runout and warpage. If necessary, follow the instructions in the Service Manual under FRONT WHEEL to replace the discs. Chrome Caliper Installation 1. See Figure 3. Obtain the correct-side new chrome caliper assembly from the kit. Remove the screen cover (5), retaining clip and pad pin (4) from the caliper. NOTE Do not remove the shipping plug protecting the brake line threaded hole until ready to install the brake line. 2. Place the caliper over the brake disc with the brake line threaded hole (protected by a shipping plug) facing upward. 3. See Figure 1. Obtain two of the brake caliper mounting bolts (1), removed earlier. Loosely install both bolts through the front fork and into the chrome caliper. Alternately tighten the mounting bolts to 38.0-51.5 Nm (28-38 ft-lbs) . 4. Install the brake pads removed earlier or, if necessary, new brake pads into the caliper. 5. See Figure 2. Install the new pad pin (1) through the inner and outer brake pads. Tighten to 8.5-11.5 Nm (75-100 in- lbs ) . 6. Install the new retaining clip (2) onto the pad pin. NOTE Ensure that the screen cover is oriented with the single tab end up, and the double tab end down. 7. See Figure 1. Install the new screen cover (5) onto the caliper.

Incoming search terms:

Skyteam ST 125 SPECIFICATIONS AND SERVICE MANUAL

0

Filed Under (Skyteam) by admin on 24-11-2010

download
BRAKES This motorcycle has a hydraulic brake system of front and rear . Brakes are items of personal safety and should be properly adjusted. Remember to check periodically the brake system and these checks should be conducted by qualified Jincheng dealer. Do not use the remained brake fluid from on a unsealed container, never reuse the brake fluid remained in the last repairing, because the used brake fluid may absorb the water from the air. Use DOT 4 brake fluid from a sealed container. Do not spill out the brake fluid, when the brake fluid is glued to the paint, plastic and rubber material, a chemical reaction shall take place, causing the damage. (1)lower level mark Front brake Rear brake BRAKE FLUID (1) (2) (3) (1) (1)Brake fluid cap (2)Max. fluid level mark (3)Min. fluid level mark Brake fluid may cause irritation. Avoid contact with skin or eyes. In case of contact, flush thoroughly with water and call a doctor if your eyes were exposed NOTICE WARINING * 9 BRAKE LINING The main points for checking the front brake lining are to see whether the lining wear is out of the range. Replace the brake lining wear is out of the range. Replace the brake lining if the lining wear is beyond the brake wear limit mark. FRONT BRAKE FLUID LEVEL Check that the fluid level is above the lower level mark(1) with the motorcycle in an upright position. Brake fluid must be added to the reservoir when ever the fluid level begins to reach the lower level mark(1). Fill the reservoir up to upper level mark. REAR BRAKE FLUID LEVEL There are two marks in rear brake fluid cap,keep the fluid lever between the Max. fluid level mark (2) and the Min. fluid level mark (3) always. Check if it is short of brake fluid, check the hose and other components for corrosion or cracks. limit mark Brake Pad Front brake Rear brake If the brake system or brake linings have to be repaired, we suggest that these repair should be performed by your authorized SKYTEAM dealer. SKYTEAM dealer knows your motorcycle best and is dedicated to your complete satisfaction

Incoming search terms:

Kymco People 125/ 150 FRONT WHEEL/ FRONT BRAKE/ FRONT SUSPENSION

0

Filed Under (Kymco) by admin on 12-12-2010

download
SERVICE INFORMATION GENERAL INSTRUCTIONS Remove the motorcycle frame covers before removing the front wheel. Jack the motorcycle front wheel off the ground and be careful to prevent the motorcycle from falling down. During servicing, keep oil or grease off the brake drum and brake linings. Contaminated brake disk or brake pads reduce stopping power. Clean the contaminated brake disk with high-performance brake degreaser and replace the brake pads. Do not use brake fluid for cleaning. Bleed air from the brake system if the brake system is removed or the brake is soft. Do not allow any foreign matters to enter the brake system when filling it with brake fluid. Brake fluid will damage painted surfaces and plastic parts. When servicing the brake system, use shop towels to cover and protect rubber, plastic parts and coated surfaces. Wipe off any spilled brake fluid with a clean shop towel. Inspect the brake system before riding. SPECIFICATIONS Item Standard (mm) Service Limit (mm) Axle shaft runout ─ 0.2 Radial ─ 2.0 Axial ─ 2.0 Front brake lining thickness 5.5 2.75 Front shock absorber spring free length 260 252 Brake disk thickness 3.2_3.5 3.0 Brake disk runout ─ 0.25 Brake master cylinder I.D. 12.700_12.74312.75 Brake master cylinder piston O.D. 12.657_12.68412.64 Brake caliper piston O.D. 33.910_33.93433.901 Brake caliper cylinder I.D.

HARLEY DAVIDSON REAR BRAKE CALIPER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Prepare the Motorcycle for Service To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Follow the Service Manual instructions to disconnect the negative (-) battery cable. Remove Rear Brake Caliper Remove the Brake Pads 1. For models equipped with saddlebags: Remove the right-side saddlebag. Refer to the SADDLEBAGS section of the Service Manual. 2. Remove the rear master cylinder reservoir cover. 3. Pry both the inside and outside pads away from the brake disc and toward the caliper assembly to push the caliper pistons back into their bores. Use steady pressure to prevent scoring the brake disc. Pry between the pads and the brake disc. 4. When the pistons are fully retracted into their bores, pull the pad pins out to allow the pads to drop from the caliper assembly. Note the pads’ original orientation for installa- tion. 5. Install the cover on the rear master cylinder reservoir. NOTE Place a container under the brake caliper to catch brake fluid released when removing the brake line from the caliper. 6. Remove the banjo bolt fastening the rear brake line to the stock rear brake caliper. Save the banjo bolt for brake caliper installation and discard the two steel/rubber gas- kets. Remove the Stock Rear Brake Caliper 1. Apply isopropyl alcohol to the rubber bumper on the brake caliper to ease removal. 2. Lift the stock rear brake caliper toward the front of the motorcycle. The notch in the caliper must clear the weldment on the swing arm. 3. Remove the caliper from anchor weldment on rear swingarm. Inspect Pad and Pins 1. Inspect the brake pads. If friction material above the backing plate on either pad is 0.040 in. (1.02 mm) thick or less, replace the set. Follow the instructions in the Service Manual. 2. Inspect pad pins for wear and grooving. If wear is more than 0.015 in. (0.38 mm), replace both pins. 3. Inspect the brake disc and, if necessary, follow the instructions in the Service Manual to replace the brake disc. Install the Rear Brake Caliper NOTE Pay close attention to all warnings, cautions, and torque specifications in this instruction sheet and in the service manual when installing this rear brake caliper. NOTE Apply isopropyl alcohol to the rubber bumper for ease of installation. 1. See Figure 1. Position the caliper (1) between the brake disc and the rear fork. The weldment on the fork should fit between the notch and rubber bumper on the caliper. Verify that the full length of the rubber bumper contacts the underside of the weldment

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

2007 Ural Models Gear Up Patrol Tourist Installation Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
Font Brake Control Lever Clutch control lever: When the clutch lever is squeezed, the engine is disengaged from the gearbox. When the lever is released, the engine and gearbox are engaged. WARNING: MAKE SURE FINGERS ARE NOT POSITIONED BETWEEN HAND CONTROL LEVERS AND HANDLEBAR GRIPS OR OPERATION OF VEHICLE COULD BE IMPAIRED . WARNING: B EFORE STARTING ENGINE , ALWAYS SHIFT TRANSMISSION TO NEUTRAL TO PREVENT ACCIDENTAL MOVEMENT WHICH COULD CAUSE POSSIBLE DAMAGE TO MOTORCYCLE AND PERSONAL INJURY . Caution: Always engage the clutch release lever when shifting. Serious internal damage may result to the transmission if the clutch release lever is not engaged. Front brake control lever: When the lever is squeezed, the front wheel brake is actuated. The front brake should be used together with rear brake. When the brake lever is squeezed, the stop signal lights are switched on. 19 Kickstart lever : Designed to start the engine. Upon kicking the lever the crankshaft is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Gear shift lever: This is a heal shift type of lever. To shift up from a low gear to a high gear the rear arm(heal shift) is pressed. To shift down from a high gear to a low gear the from arm is depressed. Since the heel-toe shift lever is short-coupled, it is much easier to shift up using the heal shift, and to shift down using the toe shift with the ball of your foot. The neutral gear is between the 1st and 2nd gears. It is important to shift smoothly with a constant force, and not to kick the gear shift pedal. Serious damage may result to the shifting mechanism if the gear shift pedal is kicked, rather than pressed. NOTE: The neutral lamp will illuminate when the transmission is in neutral. (see “Starting the Engine”). Gear Shift Foot Pedal Kick Lever 20 Parking Brake Sidecar Drive Lever Rear Brake Pedal Parking Brake: Used to hold the bike when parked. To engage, press the rear brake pedal, push down and twist the parking brake lever counter clockwise. Sidecar drive engagement lever: Used to engage the drive axle to the sidecar wheel on the Patrol and Gear Up model motorcycles. WARNING: Never engage sidecar drive on concrete or hard surface. Severe damage to drivetrain will result if the sidecar drive is engaged on pavement. Rear brake lever: Actuates the rear brakes on both the motorcycle and sidecar. WARNING: DO NOT APPLY EITHER BRAKE STRONGLY ENOUGH TO LOCK THE WHEELS BECAUSE THIS MAY CAUSE POSSIBLE LOSS OF CONTROL OF THE MOTORCYCLE . ALWAYS USE BOTH BRAKES . NEVER STOP WITH FRONT OR REAR BRAKE ONLY . WARNING: AN IMPROPERLY ADJUSTED REAR BRAKE PEDAL COULD INTERFERE WITH PROPER REAR BRAKE OPERATION RESULTING IN POOR BRAKE ACTION

Incoming search terms:

HARLEY DAVIDSON ROAD KING FAT HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
PREPARATION – ALL MODELS To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. See the service manual and remove the seat and disconnect battery cables or remove the main fuse. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will dama ge painted and bod y panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTES Immediately wipe up any brake fluid spills with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spilled D.O.T. 4 brake fluid. 2. See the service manual and drain the brake fluid from the front brake reservoir. ORIGINAL HANDLEBAR REMOVAL NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 1. Using a T-40 TORX® drive head, remove and retain the button head screw on the underside of the fork stem and bracket assembly that holds the brake line manifold tee. 2. Carefully make note of the front brake line routing and the orientation of the banjo fittings. Disconnect the brake line from the front brake calipers and the front brake master cylinder assembly. Save the banjo bolts, but discard the two gaskets found at each banjo fitting. See FRONT BRAKE MASTER CYLINDER in the service manual. 3. Remove the old brake lines from the motorcycle. 4. Using a T27 TORX drive head, remove the front-brake master cylinder and clutch-lever assemblies (refer to CLUTCH CABLE in the service manual) from the stock handlebar.

HARLEY DAVIDSON XL PULLBACK HANDLEBAR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
Installation Removing the Existing Front Brake Line To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative battery cable. Retain all seat mounting hardware. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) 2. See Figure 1. Open the bleeder nipple cap on the front brake caliper. Obtain a length of plastic tubing. Install one end of the tubing over the caliper bleeder valve (1). Place the free end of the tubing into a suitable container. Open the bleeder valve about 1/2-turn and pump the front-brake hand lever to drain the fluid out of the front brake system. Do not reuse brake fluid. NOTE Cover the front fender and the front of the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. Avoid leakage. Be sure gaskets, banjo bolt(s) and clutch line are clean and undamaged before assembly. (00329a) 3. Disconnect the brake line from the front brake caliper and the front brake master cylinder assembly. Discard the brake line sealing washers, but retain the banjo bolts. The brake line kit contains all new sealing wash- ers. CAUTION 1 CAUTION 1 WARNING 1 WARNING 1 WARNING ® Kit Number 56021-04B 1 of 6 Figure 1. Draining Brake Fluid i01986 i05811.tif 1 1. Caliper bleeder valve NOTE Carefully compare the new brake line to the old line before removing the old linefrom the motorcycle. Make sure the banjo fittings on the new brake line will be oriented the same as the fittings on the old line. 4. Make note of the front brake line routing and the orientation of the banjo fittings, then unfasten the brake line clamps at the right side of the front fork upper bracket and the underside of the front fork lower bracket, and remove the brake line assembly from the vehicle. Save the upper clamp and all attaching parts, but discard the brake line.

Incoming search terms:

Incoming search terms: