r1200rt glove box tray

You search Auto repair manual PDF r1200rt glove box tray, if there are search results will appear below. If search results do not exist, please search by others keyword.



  r1200rt glove box tray Direct Download speed 5282 Kb/s

  r1200rt glove box tray Full Version speed 6162 Kb/s



HARLEY DAVIDSON LOCKING GLOVE BOX DOOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION 1. Unsnap the original equipment (O.E.) left-side glove box door, and unfasten the tether by bringing the aglet end (see Figure 1, B) out through the retaining hole. Always wear proper eye protection when drilling or grinding. Flying debris could cause serious eye injury. (00402e) 2. Using an 3/16 inch (5 mm) bit positioned in the center of each snap, drill out the four plastic snaps surrounding the glove box opening. NOTE The glove box door, hinge and frame assemblies are side- specific. The assemblies install so that the tether retaining hole (C) in the door frame is to the inboard side. 3. Obtain the new left-side glove box door, hinge and frame assembly (1), a lock (2) and a tether assembly (8) from the kit. Remove the nut (3) from the lock. 4. Insert the lock through the hole in the glove box door as shown. Assemble the tether over the lock threads with the tab (A) on the inboard side of the lock, same as the retaining hole in the door frame. Tighten securely. 5. Open the left-side door, and position the door assembly at the glove box opening, lining up the holes. 6. Insert a screw (9) through each of the holes in the door frame and glove box. Install a hex nut with washer (10) onto the threads of each screw. Tighten finger-tight. NOTE Ambient temperature should be at least 60° F (16° C) for proper adhesion of the gaskets to the glove box door frame. 7. Clean the glove box door frame with a mixture of 50 to 70% isopropyl alcohol and 30 to 50% distilled water. Allow to dry thoroughly. NOTE The glove box gaskets are side-specific. With the paper backing facing the door frame, the oblong hole at the top of the gasket is to the outboard side. 8. Obtain the left-side gasket (6) and a hinge gasket (7) from the kit. Install the gaskets to the glove box door frame. a. The gasket liner on the large gasket is split to aid alignment. Peel one half of the liner from the adhesive backing of the left-side gasket. b. Using the frame edges and screw heads as a guide, carefully position the gasket to the glove box door frame and press firmly into place. c. Peel the remaining half of the liner from the gasket backing, and carefully position the rest of the gasket to the door frame. Press firmly into place. d. Apply steady pressure for a few seconds at all areas of the gasket to verify proper adhesion. e. Peel the liner from the hinge gasket. f. Carefully position the gasket to the door frame above the hinge, and press firmly into place.

Incoming search terms:

Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

LED Motorcycle Power Box Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
This box requires the presence of a mounting plate secured to the motorcycle’s luggage rack. If the bike in question is not equipped with a mounting plate, one must be fabricated prior to installation of this box. Five mounting holes (.281″ dia.) are required to mount this box. If the motorcycle is already equipped with a mounting plate, it may be necessary to drill the 5 mounting holes required for this installation. Use the diagram shown to determine the precise location of these holes. 1. Position the box onto the mounting plate. Align the 5 vibration dampeners with the 5 mounting holes in the mounting plate. 2. Using the illustrations shown, secure the box to the mounting plate using the provided hardware. Note: Your luggage rack may already have the correct mounting holes drilled. Check the measurements below and if these holes already exist at the proper distance, remove any existing mounting hardware from the holes and secure the box with the supplied mounting hardware. 3. Place the box into its mounting position on the deck and secure it with the supplied mounting hardware as shown in the diagram. Wiring: Diagrams for optional equipment are found below. Refer to the diagram on the following page for general motorcycle box wiring information

Incoming search terms:

HARLEY DAVIDSON SOFTAIL LEFT SIDE LEATHER TOOL BOX KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
Installation While handling and installing tool box, be careful not to scratch surface. 1. See Service Parts Illustration. Install tool box (1) to mounting bracket (6) using button head screws (2) and washers (5). Screws (2) should be inserted through mounting holes on inside of tool box (1) and then inserted through bracket (6) holes and threaded into weld nuts attached to bracket. 2. Remove and save the two screws that secure left rear fender support to motorcycle frame. 3. Remove two bolts, nuts, and washers that secure debris deflector to motorcycle frame. This will allow you to move debris deflector out of the way when installing new passenger footpeg support bolt. Save hardware for reinstallation. 4. For 1990 to 1999 Softails: If tool box is being installed with passenger footpeg, remove the hex head bolt and left passenger footpeg. Retain footpeg and lockwasher for reinstallation. Discard bolt . If tool box is being installed without passenger footpeg, remove hex head bolt and left passenger footpeg. Discard footpeg. Retain bolt and lockwasher. For 2000 and later Softails: See page 3 . Remove footrest from clevis. Remove clevis from frame by removing cap screw from center of clevis. If tool box is installed with footpegs, keep all hardware. If toolbox is to be installed with footboards, discard hardware. 5. Slide top of mounting bracket (6) between rear fender support and frame. Align top holes in bracket with fender support holes. Align lower bracket hole with footpeg mounting hole in frame. Install the two screws, removed in Step 2, in fender support. Do not tighten screws at this time. 6. For 1990 to 1999 Softails: Place lockwasher retained in step 4 on footpeg support hex head bolt (3) from kit. CAUTION 1 of 3 For 2000 and later Softails with footpegs: Install kit 49352-00 according to instructions included in this kit. Footpeg must fold up at a 45°angle (from vertical) toward rear of motorcycle. This angle allows footpeg to fold up if, by accident, it strikes the ground surface when making a sharp turn. Failure to set footpeg to the proper fold-up angle could result in death or serious injury. 7. For 1990 to 1999 Softails: Position footpeg so it folds up and back at a 45°angle. Install bolt (3) from kit through frame, tool box bracket (6), and spacer (4), into footpeg, as shown. NOTE If vehicle is equipped with saddlebag support bracket, Part No. 90346-90 or 90346-94, position saddlebag support bracket between tool box bracket and spacer.

Incoming search terms:

Harley Davidson Electra Glides, Ultra Vent (model LV-2,3,4) Installation Manual

0

Filed Under (Harley Davidson) by admin on 07-03-2012

download
Remove the fairing lower from the engine guard using the procedure provided in your Harley-Davidson user/service manual. Do not remove the glove box from the fairing. Vent Placement, Hole Drilling and Cut-Out: Caution: Place cloth or cushion underneath fairing lower to protect it from getting scratched during the following procedures. LV-2,3,4 Installation Copyright 2003-2004 2 3. Working inside the fairing and using the bottom of the glove box as a guide, position a closed vent parallel to and no more than 1/16″ from the rear edge of the fairing. Position the assembly so that the vent side tabs are no more than 1/8″ below the bottom of the glove box. (You want the vent assembly as close as possible to the glove box but with enough room so that the side tabs do not touch the glove box when the vent is closed! ) Mark the back two holes with a pencil then remove the vent and replace it with the cutting template in the exact same location. See photo to the right to assist in judging the cutting template orientation. 4. Lift out the glove box, steady the template with one hand and using an 11/64″ drill bit carefully drill 1 hole near the back edge of the fairing through the bottom corner hole of the cutting template. Install one screw and nut and tighten slightly to stabilize the template’s location. On the other corner (same edge) , drill the second hole. (You cannot drill the remaining holes from inside the fairing because the front edge of the fairing lower is in the way. ) 5. Remove the screw and nut and re-position the cutting template on the outside of the fairing with the three hole side of the template towards the front of the fairing (away from the edge of the fairing) . Install two screws and nuts into the open holes. Drill the remaining two corner holes and install two screws and nuts. Change drill bit size to 1/8″ to drill the final center latch hole. Next skip down to one of the two following procedures to make the vent opening using either A) Dremel tool/RotoZip router or B) coping saw/frameless hacksaw

Harley-Davidson Motorcycle Services Changeout/ Set Up/ Maintenance/ Repairs

0

Filed Under (Harley Davidson) by admin on 28-03-2012

download
The Vendor shall use the custom wiring specifications from the current model year Harley-Davidson set ups. One fully outfitted 2005 model is being decommissioned and may be used as a model for 2006 set up. 2. Attach custom tray, rear box, and custom electronics box to rear mount. Rear box should be attached to the rear of the motorcycle using no more than four mounting holes. The rear box shall be adjusted to the officer assigned to the motorcycle by moving it forward or to the rear and by using spacers to elevate the box for saddlebag lid clearance. 3. Install custom brackets for radio, radar/lidar, flashlight and rear box tray. Brackets from changed-out motorcycles can be used on the new motorcycles and vendor shall modify or reinforce to correct metal fatigue as necessary to maintain functionality. 4. Install all components in the rear electronic box to facilitate repairs and maximize available storage space. These components include power source for cell phone, two-way radio, opticom power supply and auxiliary fuse panel. 5. Set handlebars, hand controls and position of rear tour pack to proper height and alignment for assigned rider. 6. A 5-sided box (base and 4 sides) metal frame is included in 2004 models and will be re fabricated into a 3- sided box (base and 2 sides) and painted black by the Vendor to match existing 2005 models. This arrangement shall allow for a full-size closed-face “Syncrotec” helmet to be stored in the rear tour pack in addition to mounted specialized equipment.

HARLEY DAVIDSON ELECTRA-GLO LIGHT POD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION NOTES Clean the controller mounting area and the areas where the light pods will be mounted with soap and water before beginning the installation, and allow to dry thoroughly. Remove debris, dirt and grime from the vehicle areas to be highlighted. Ambient temperature should be at least 50 °F (10 °C) for proper adhesion of the light pods and controller box to vehicle surfaces. Light pods should not be located closer than 2.5 inches (63.5 mm) from exhaust pipes or mufflers, and must have 1.5 inches (38.1 mm) clearance from engine cylinders and heads. Do not install light pods with the light source facing directly away from the vehicle. Installation should be done in a way that allows the light to be seen indirectly by reflecting from chrome or painted surfaces of the vehicle. Prepare the Motorcycle To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the owner’s manual and follow the instructions given to disconnect the battery cables, negative (-) cable first. NOTE For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase . Locate and Install the Controller NOTE Do not mount the controller box in a location where vehicle suspension travel could result in contact with the ON/OFF switch or dimmer control. Damage to the controller box will occur. 2. See Figure 2. Locate the controller box (10) on a flat surface that will allow the red (+) and black (-) leads to reach the battery terminals and the rider to access the controls (with the vehicle parked) and, if necessary, the in-line fuse holder (A). a. Test-fit the controller box to the selected surface before installation. Do not remove the adhesive backing until ready to attach the controller box. b. Clean the controller box mounting area with one of the included alcohol swabs. Allow to dry thoroughly. c. Remove the liner from the adhesive backing of the controller box. Carefully position the controller box to the surface, and press firmly into place. Hold the controller box in position with steady pressure for about one minute. Connect the Battery Cables NOTE Verify that the ignition/light key switch is in the OFF position before attaching the battery cables. 3. Verify that the ignition/key switch is turned to the OFF position. Apply a light coat of Harley-Davidson electrical contact lubricant (part number 99861-02), petroleum jelly or corrosion retardant material to the battery terminals. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 4. Refer to the owner’s manual and follow the instructions given to install first the vehicle’s positive (+) battery cable then the red (+) light pod controller lead ring terminal to the positive (+) battery terminal. Tighten to owner’s manual specifications. Install first the vehicle’s negative (-) battery cable then the black (-) light pod controller lead ring terminal to the negative (-) battery terminal. Tighten to owner’s manual specifications. Arrange the Electra-Glo Light Pods NOTES Electra-Glo light pods (1) can be installed in a variety of locations. They are best installed on a flat surface to provide indirect lighting illuminating mechanical features, vehicle finish or for ground effects. Refer to the notes at the beginning of the Installation section. 5. Select the area or lines of the motorcycle to highlight, and suitable locations for each light pod. DO NOT permanently affix the light pods at this time. Lightly tape the pods in place temporarily until the desired visual effect is achieved Verify clearance from movement of rubber mounted engine or other moving parts, heat sources, or chafe points

Incoming search terms:

2009 Kawasaki ULTRA 250X/ 260X FUEL INJECTION CONTROLLERS And REGULATORS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The R&D high performance Air Filter Kit will improve acceleration and top speed performance by increasing air flow and reducing air temperatures that enter directly into the Ultra 250X’s air plenum box area. The O.E.M. air plenum box on the Ultra 250X is a great design that will flow plenty of air. However, the air that feeds the plenum box is heated by the engine. R&D has created an easy to install “flat filter” that installs directly in place of the large center access inspection cover located directly under the main glove box. The R&D Flat Air Filter insert will allow unrestricted fresh and cool air to enter the air plenum box area which will add power you can feel and a nice high performance tone. The R&D Performance Filter Kit also features two filters, one for each of the surge and blowoff protections valves. The O.E.M. surge valve recycles compressed hot air back into the air box plenum at idle and under deceleration conditions. The R&D surge and blowoff valve filter kit removes the air recycling hoses which will keep the hot air from entering the air plenum box reducing the engines intake air temperatures. The R&D Ultra 250X Air Filter Kit offers great performance tips on how to remove the restrictive air vent hoses which will further reduce the under seat ambient air temperatures. The R&D Filter system does not remove or alter the O.E.M. plenum box in any way, therefore there are no questions to be answered regarding water ingestion

Incoming search terms:

Toyota Power Steering Conversion Kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 04-10-2011

download
Remove the stock steering box and column. Be sure to clear the area of all wiring, brake lines and fuel lines. 2. Bolt the Toyota box to the mounting bracket so that the long arm of the bracket points in the same direction as the steering column input shaft (small shaft.) To mount the bracket and box correctly, the longer end should be towards the rear of the vehicle. It may be necessary to grind on the power steering box where the two flanges protrude above the bracket. For technical help call Classic Performance Products Monday thru Friday 8:30am to 5:00pm at (714) 522-2000. Rev. 8/17/2009 3. Locate the box/bracket assembly into the frame by centering the Toyota sector shaft through the original hole in the frame. This hole will need to be elongated approximately 3/8″ to allow the sector shaft to clear the frame. Bolt the bracket directly into the mounting holes for the original steering box. 4. With the first bolt in, check the fit by reattaching the steering box. Make sure the splined shaft goes through the frame without interference. Torque down the mounting bolts to 45 lbs. 5. Attach the pitman arm to the steering box. Before this is done the steering sector must be centered. Turn the input shaft clockwise as far as it can go. Make a reference mark. Now turn the shaft counter clockwise as far it can go and be sure to count the turns. Turn the shaft back half the distance and now the box is centered. Be sure to double and triple check this procedure. Attach the pitman arm to the output shaft with the output shaft nut. Torque the bolt down to 110ft/lbs. Reconnect the stock drag link and you are on your way

2007 Harley Davidson Sportster 1200 Installation Manual

0

Filed Under (Harley Davidson) by admin on 11-04-2012

download
1 Remove the stock seat. 2 Unplug the stock wiring harness from the ECM (Fig. A) . 3 Remove the ECM from the tray and remove the tray from the fender. You can reach underneath the fender to gain access to the release tabs for the tray. 4 Install the Dynojet tray into the rear fender . Make sure that all 3 location tabs are underneath the fender. 5 Lay the PCIII in the tray (Fig. B). 6 Install the stock ECM on top of the PCIII making sure that it is secured by the tray locking tabs. 7 Plug the GREYconnector from the PCIII into the ECM. 8 Route the PCIII harness on top of the GREY connector (Fig. C) and route towards the front of the bike. Fig. A Fig. B Fig. C 2007 Harley Davidson Sport ster 1200 – PCIII USB – 2 i817-51 1 www .powercommander .com Unplug Tray 9 Plug the BLACK connector from the PCIII into the stock wiring harness. Secure this connection with one of the supplied zip ties (Fig. D). 10 Run a zip tie behind the wiring harness (Fig. E). 11 Route the stock wiring harness as shown in Fig. E. Due to the lack of room on this bike this step needs to be exact or the install will not fit properly . Make sure that the harness coming from the GREYconnector is flush against the battery box. Acouple inches of this harness will be tucked underneath the frame

Incoming search terms:

Incoming search terms: