r15 how to replace the ecu

You search Auto repair manual PDF r15 how to replace the ecu, if there are search results will appear below. If search results do not exist, please search by others keyword.





Lilac LS-18 Motorcycle Maintenance Standards

0

Filed Under (Lilac) by admin on 25-11-2010

download
CYLINDER AND CYLINDER HEAD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Cylinder Bore 54 -0.01 54.1 Boring After boring honing should be performed Ovality 0.01 0.05 Boring After boring honing should be performed Taper 0.01 0.05 Boring After boring honing should be performed Oversize 0.25 steps 55 max. Do R and L cylinders at same time / 4 steps Valve Seat Width 0.8 – 1.0 1.3 Adjust Use a cutter Angle 45∞ Combustion Chamber Volume 18.2cc -0.5cc Remove carbon if heavy accumulation Compression Ratio 7.8:1 Head Gasket Thickness 1.0 Cylinder Head Nut Torque 3.0 kg/m (22 ft.-lb.) Out standard Adjust 8mm nut Intake and Exhaust Ports Port Wall SurfaceMust be smooth Remove carbon Intake and Exh. Valve GuidesOD 12 +0.09 +0.1 ID 7 +0.01 -0.0 7.06 Exchange Intake Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Exhaust Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Intake and Exhaust Valve Seat Face Width Range 0.8~1.0 1.3 Use valve seat cutter Intake Valve Guide Clearance 0.02~0.04 0.08 Replace valve or guide Exhaust Valve Guide Clearance 0.06~0.08 0.12 Replace valve or guide Valve Spring (Large) Installed Load 10.2 kg 8.7 kg Replace Fitted length 31.5 Free Length 36.5 34.7 Replace Tilt 1.5/100 3/100 Replace Valve Spring (Small) Installed Load 5.48 kg 4.65 kg Replace Fitted length 29.5 Page 4 of 10 Free Length 33.5 31.8 Replace Tilt 1.5/100 3/100 Replace Rocker Arm ID 12 +0.00 +0.02112.07 Replace Rocker Shaft OD 12 -0.06 -0.024 11.92 Replace Arm and Shaft Clearance 0.045~0.006 0.10 Replace arm or shaft Tappet Clearance 0.05 Out standard Adjust Measure cold at TDC Rocker Arm Ball Surface 1.8îR -0.006 -0.024 Replace if severe wear Pushrod Bend 0.1 0.5 Straighten Over 100mm (2) CRANKSHAFT, PISTON AND CONROD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Piston OD @ Top 53.65 -0.02 Max Diameter 53.95 -0.015 53.85 Replace Ovality 0.1 Piston and Cylinder Clearance 0.04~0.05 0.15 Replace Piston Ring Groove Clearance 0.03~0.07 0.10 Replace Piston Oversize Step 0.25 4 steps Top Ring and 2nd Ring Thickness 2 -0.01 -0.03 1.92 Replace Width 2.5 -0.01 0.55kg Tension 0.85 – 1.15kg 1 Replace End Gap 0.15 – 0.35 Replace Oil Ring Thickness 3.2 -0.01 -0.03 3.12 Replace Width 2.5 -0.1 Tension 1.0~1.3kg 0.65kg Replace End Gap 0.15~0.35 1 Replace Ring Gap Position 120∞ 3 equal spacesOut standard Adjust Avoid Piston Pin Axis Ring Oversizes 0.25 steps 4 steps Piston Pin OD 15 -0.0 +0.006 14.95 Replace Pin Hole in Piston ID 15 +0.012 -0.015.05 Replace Pin and Piston Clearance -0.006 ~ +0.012 0.06 Replace Hand push fit piston at 100∞C Conrod Small End Bush ID 15+0.027+0.016 15.07 Replace bush Conrod and Piston Pin Clearance 0.01~0.027 0.07 Replace Crankpin OD 24.94 +0.0+0.0124.90 Replace Crankpin Roller OD 5 (+0.001+0.003) Refer to conrod ID Replace 3Sizes; 52 per assembly for selective fit 5 (+0.0 -0.002) 5 (-0.003 -0.005) Conrod ID 34.95+0.03+0.02435.02 Axial Play 0.2~0.4 0.5 Adjust Radial Play 0.026~0.036 0.06 Replace

Incoming search terms:

BMW F 650 GS Repair Manual And Maintenance schedule

0

Filed Under (BMW) by admin on 19-11-2010

download
Replace oil in telescopic forks Check the coolant and restore to correct level if necessary *) Replace the coolant (every 2 years) every 2years Check valve clearances, adjust if necessary Replace the spark plug Drain the outlet hose from the air filter box Replace intake air filter If motorcycle is operated in very dirty or dusty conditions, clean or replace the intake air filter every 10,000 km (6,000 miles); check every 3,000 km (1,800 miles) Replace fuel filter (every 20,000 km/12,000 miles) 20,000 km Check clutch play, adjust if necessary Check wheel spoke tension and tighten if necessary more frequently if motorcycle is ridden in severe off-road conditions Examine brake pads and discs for wear, replace if necessary *) more frequently if motorcycle is ridden in severe off-road conditions Check brake fluid level at front and rear and top up if necessary *) Check for operation of brake system and freedom from leaks; repair/replace if necessary *) Replace the brake fluid at least once a year Replace the primary front/rear brake master cylinder cup (every 40,000 km/24,000 miles on a motorcycle with ABS ) 40,000 km Check wheel bearings and replace if necessary *) Check or, if necessary, replace chain, sprocket, chain guide rollers and pinion *) more frequently if motorcycle is ridden in severe off-road conditions Check chain tension and adjust if necessary *) Check battery acid level, add distilled water if necessary more frequently if motorcycle is ridden in severe off-road conditions Clean and grease the battery terminals, if necessary Check steering head bearings and adjust *) or replace if necessary *) Grease the side and main stands Grease the brake pedal Check bolts and nuts on engine mountings, frame connections, exhaust system mountings, swinging fork pivot, suspension levers, brake pedal, main and side stands and quick-release axles for tightness Final inspection with road safety and functional check

2001 – 2003 Prius 2003 4Runner, Camry, Land Cruiser and Sequoia VEHICLES EQUIPPED WITH TRANSPONDER ECU

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
When replacing the ECM (SAE term: PCM) or the Transponder ECU a “handshake” procedure must be performed. This ECU ID communication is necessary to enable the Transponder ECU and the ECM to recognize each other before the vehicle will start. Complete ECU communication using the following steps: 1. Insert a Master key into the ignition cylinder. 2. Turn the ignition ON (engine OFF). 3. Short Tc and CG terminals of DLC3 using the Diagnostic Check Wire (SST 09843-18020 or equivalent) and leave for 30 minutes. 4. After 30 minutes, turn the ignition OFF and remove check wire from DLC3. 5. Register any additional keys as necessary. 6. Start the vehicle to confirm successful ECU communication. Key Programming: To program or delete a key, a registered Master key is necessary unless the Transponder ECU has been reset or replaced. The Transponder ECU system incorporates a black “Master” key and a gray “Sub” key. The process during registration of these two keys is identical. The key itself now determines if it functions as Master or Sub, not the registration procedure. The maximum number of allowable Master and Sub keys vary by model. Refer to the chart below.

Incoming search terms:

Honda CBR F4 or F4I 600cc Engine PE-ECU-1 System INSTALLATION

0

Filed Under (Honda) by admin on 05-01-2012

download
The PE-ECU-1 can be installed on virtually any 1,2,4,6 or 8 cylinder even-firing engine that requires fuel injection and/or ignition control. All of the functions of the ECU can be adjusted by using a laptop or PC running Windows. The following describes the basic requirements for using the system with a Honda 600cc F4 or F4I motorcycle engine. Please refer to the User’s Manual for a more in-depth description. Input Sensors The stock Honda F4 and F4I crank position sensors can be used with the PE-ECU-1 engine control system, provided the engine controller is configured for a 2- wire variable reluctance sensor. The configuration for the input is handled at the factory via a set of board jumpers. If the type of crank sensor should ever be changed, please contact PE for support on this issue. The stock Honda crank sensor should be wired according to the following: • Solid Yellow Wire – Pin 34 on ECU • Yellow with White Stripe (GND) – Pin 25 on ECU Failure to wire the sensor in this way may result in an engine that misfires and/or has incorrect ignition timing. The stock Honda trigger wheel cannot be used with the PE-ECU-1 system due to the differences in the number and spacing of the teeth. The PE-ECU-1 must be provided with a 12-1 pulse-train, correctly phased with TDC #1 according to Figure 1

Incoming search terms:

POLINI X1 GENERAL INFORMATION AND SPECIFICATIONS

0

Filed Under (Polini) by admin on 02-12-2010

download
Air cleaner – Clean and reoil daily or after each moto to prevent motor failure and reduced performance. Transmission oil – change after every race, or at end of riding day. Chain – check tension and lubricate before every ride, adjust or replace as needed. Reoil after riding in damp conditions. Clutch – disassemble and clean clutch assembly frequently, every 2-3 races at least. Inspect kickstarter gears at this time. Ignition cover – remove cover and wipe dry after each ride or after washing bike to remove condensation. Piston rings – replace as often as every 3-5 races with expert rider, less often with less aggressive riders. Piston, pin, rod bearing & circlips – replace as often as every 8-10 races with expert rider, less often with less aggressive riders. Coolant – change yearly, make sure there is at least a 50/50 mixture of antifreeze if freezing temperatures are possible. Steering bearings – Check daily for looseness or play. Adjust and regrease as needed. Swingarm – Check often for looseness. Regrease several times a year. Replace bushings if any play is evident. Sprockets – check for worn or curved teeth each time chain is adjusted. Chain roller& wear pads – check roller for free rotation when checking chain. Make sure roller is not bent or damaged. Check chain wear strips on swingarm and chain guide frequently. Replace as needed to prevent chain from damaging motorcycle. Spokes – Check after each race or after each day of riding for looseness or damage. Wheels & tires – check wheels after each race for dents, cracks or other damage. Check tires for cuts, damage or wear. Check tire pressure daily and adjust for riding conditions. Shock – Check shaft area daily for signs of oil leakage or damage. Check swingarm and shock bushings for looseness. Forks – Check forks daily for leaking oil or damage to tubes. Make sure forks are not twisted check for smooth operation. Spark plug – check sparkplug color and condition after each race or end of riding day. Adjust jetting to keep plug from fouling or overheating. Silencer – If bike seems to be getting louder, replace packing and decarbonize inner tube. Expansion pipe – check daily for large dents, damage or leakage. Remove carbon from headpipe when pipe is removed. Have large dents fixed, or any dents within 8″ of the cylinder. Replace o-rings on pipe as needed to maintain a good seal. Footpegs – check daily for proper operation, pegs should spring back into place. Make sure pegs are not bent or overly dull. Handlebars – check bars after any crash for bending. Look for cracks near bar clamps. Replace bars that have been straightened more than 2 or three times, or if bar is badly bent. Aweakened bar can snap suddenly causing injury to rider. Throttle – check throttle for proper operation each time before bike is started. Remove and clean inside of grip and bar as needed. Grips – check grips daily for wear or looseness. Replace as needed. Use grip glue & safety wire to help hold grips in position. Calipers & pads – check pad wear and caliper function daily or after each race. Replace pads and clean calipers as needed. Brake lever – check lever daily for damage or wear. Make sure lever is at proper angle for both seated and standing positions. Leave lever clamp loose enough to allow clamp to rotate during crash rather than breaking lever. Check and adjust freeplay as needed. Brake pedal – Check pedal daily for damage and proper freeplay. Adjust rear caliper as needed. Reeds – Remove and inspect reed block during every ring change. Check reeds for signs of wear, fraying and cracking. Make sure reeds sit flat and seal well. Replace at any sign of wear or damage or at least once a year, more often for expert riders. Nuts & bolts – Check all nuts and bolts regularly. Make sure to check engine mounting bolts and swingarm bolt frequently

Incoming search terms:

Ducati 1098 and 1098S ECU connection Installation Manual

0

Filed Under (Ducati) by admin on 25-10-2010

download
ECU can be connected to AIM loggers in two different ways: directly, or using the connector placed on the dashboard. 2.1. – Direct connection between AIM loggers and Marelli IAW 5AM2 ECU IAW 5AM2 is equipped with two 38 pins connectors, named “Body ” and “Engine” – see below: “engine” is black (on the left). “Body” connector is grey (on the right). To connect AIM loggers to Ducati ECU: • connect AIM cable labelled CAN+ to pin 20 of “Body” connector. • connect AIM cable labelled CAN- to pin 29 of “Body” connector. • Vbatt is on pin 17 (vehicle master switch). 2.2 – Dashboard connector Connector is equipped with 26 pins and it is placed on the back of the dashboard. To connect AIM loggers to ECU using the dashboard connector: • connect AIM cable labelled CAN+ to pin 19 (green/black twisted cable) connector. • connect AIM cable labelled CAN – to pin 26 (grey/green twisted cable) connector. • Vbatt is on pin 23 – red /black cable – vehicle master switch. Warning: to use Marelli dashboard , please remove 120 OHM resistance placed between CAN+ and CAN-; otherwise Marelli dash does not work

Incoming search terms:

BMW R1100 – R850R Maintenance Guide

0

Filed Under (BMW) by admin on 27-11-2010

download
R1100 Checklist – Carl Kulow • Check alternator belt (replace 36K miles) • Adjust valves • Spark plugs (replace 12K) • Air filter (replace 12K) • Lube and adjust clutch cable • Lube front shock lower mount • Lube side and center stand • Check brake fluid (replace yearly) • Check brake pads • Check battery acid level • Fuel filter (replace 24K) • Throttle body sync • Oil and filter (replace 6K) • Check transmission fluid level (replace 12K) • Check rear wheel drive fluid level (replace 12K) • Check tires and pressure • Check all nuts and bolts • Check all air and oil hose clamps • Check all lights PARTS – TOOLS Tools Parts Misc. sockets spark plugs compressed air wrenches oil filter anti seize torque wrench air filter carb cleaner hex sockets brake pads rag hex wrenches oil – 4 qt. BMW #10 grease feeler gauges gear oil – 1 1/4 qt. flexible tubing oil filter tool alternator belt (tygon) flashlight fuel filter, o-ring, clamps measuring cylinder crush washers Mityvac -3 small = trans.drain, rear drive fill and drain digital volt meter -1 medium = oil drain heat gun -1 large = trans.fill tire change tools 5 R1100 Maintenance Steps – Carl Kulow Note: This overview section serves only as a step by step reminder for experienced workers. If you are unfamiliar with any procedure you should read the parenthetical reference article or Paul Glaves’ Routine R1100 Service Article! Note to R1100RT and R1100RS Riders: remove the side panels as described in your owners manual “Service and Technical Booklet” except RT: instead of pulling the mirror off as the manual says, you need to hold the back of the mirror (front of bike) with one hand while you hit the front outside corner of the mirror with the palm of your hand thus knocking the mirror off. Check Alternator Belt remove four bolts holding black plastic cover(4mm hex), remove cover, check belt for cracks etc., check belt tension, replace belt every 36K miles, leave cover off for valve adjustment (see Jon Diaz “Alternator Belt Adjustment”)

TOYOTA E ECU / COLD START INJECTOR TIME SWITCH MODIFICATION

0

Filed Under (Toyota Manuals) by admin on 17-10-2011

download
Before replacing an ECU or a cold start injector time switch, perform a thorough inspection to verify that all engine mechanical, fuel and electrical/electronic systems are to recommended specifications. PARTS RETURN INFORMATION: The replacement ECU’s are remanufactured by Nippondenso-Los Angeles (NDLA). In order to maintain cores for rebuilt units, the original ECU must be sent to NDLA as soon as it has been replaced.

Incoming search terms:

2008 Harley-Davidson TOURING INJECTION FUEL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2012

download
1. Remove seat, exposing factory computer (ECU). disconnect factory wiring by pressing lock and pushing lever back. 2. Remove ECU by pushing tab and sliding the ECU to the right as you lift. 3. Gently align the pins of the Fuelpak connector with the ECU and press the connector on the ECU. Be sure the single large pin is aligned with the single large socket before pressing Fuelpak connector into the ECU. Make sure all four tabs fully latch. (Fuelpak connector Patent Pending# 29 295831) 4. Connect factory wiring to Fuelpak connector and pull lever to locked location. Be sure that lock snaps into position. 5. Reinstall ECU. 6. Remove left side cover. 7. Slide Fuelpak down through opening leading to the area under the left side cover. 8. Attach Fuelpak to the fuse cover using supplied velcro.
HOW IT WORKS ENTERING VALUES 1. Remove Fuelpak clear case cover by removing all four screws, save hardware . 2. Turn on main power and handlebar switches, but do not start engine. Fuelpak display should light up, if not, turn power off and verify the connectors are fully seated. 3. Refer to Fuelpak Setting Reference to locate the Setting Values specific to your bike and exhaust system. If you do not find your setting, visit fuelpakfi.com or call tech support at (562) 921-0071. 4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as indicated in your Setting Value. After entering your first value, press the mode select button to move to mode 2 and enter the value. Continue until you have entered the value for each of the first 18 mode positions. Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the value decreases by one number. (Please refer to the “How It Works” section directly above if you have questions about this step. 5. By pressing the mode select button 3-times, move to mode 21 and verify that it reads “0″ 6. Enter any other mode values as required for your application. 7. Turn power off, wait one second then turn power back on. Verify all modes then turn power off. 8. Reinstall Fuelpak clear cover then reinstall side cover

1997-1998 EFI Harley Davidson 1340 EVO Power Commander Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-03-2012

download
1 Remove the seat. 2 Remove saddlebags if installed. 3 Remove left and right side covers. 4 Remove the battery (negative terminal first). 5 Loosen the two 7/16 nuts that retain the ECU (Fig. A) 6 From the left side (underneath the left side cover area) feed the PC III connectors in front of battery tray, and out the right side (in front of the ECU bracket)(Fig. B). 7 Attach PC II module to battery box. First, clean the PCIII and battery box with the supplied alcohol wipe. Using the supplied velcro attach PCIII to the battery box. Also secure the unit with the included zip ties. If your bike has cruise control, attach the unit to the face of the cruise control module (Fig. C). 8 Disconnect the large connector from the ECU. Remove the rubber dust shield. 9 Install the dust shield onto the matching connector on the PCIII. Zip tie the rubber dust shield to the PCIII connector with zip tie provided. 10 Plug the PCIII connector into the stock ECU. 11 Plug stock connector into the remaining connector from the PCIII (Fig. D). 12 Tighten the two 7/16 nuts that retain the ECU. 13 Route the connectors alongside the ECU and install the right side cover. 14 Replace the battery, the left side cover and the seat. 8 5 Power Commander Connnector Stock Connnector Fig.D Fig.E Adjust Idle Speed here Fig.F Adjusting Your Power Commander Your Power Commander has been programmed with a base map for your application. You can adjust the base map or install an alternate map using your Computer. Please refer to the supplied CD-Rom for more information. You can also adjust your Power Commander using the face plate buttons as described below. 1. With the ignition off, hold down all three buttons on the Power Commander unit. 2. While still holding down the buttons, turn the ignition on. 3. Release buttons

Incoming search terms:

Incoming search terms: