raptor 80 o ring size for carburator

You search Auto repair manual PDF raptor 80 o ring size for carburator, if there are search results will appear below. If search results do not exist, please search by others keyword.



  raptor 80 o ring size for carburator Direct Download speed 5282 Kb/s

  raptor 80 o ring size for carburator Full Version speed 6162 Kb/s



HARLEY DAVIDSON FLUSH-MOUNT LED FUEL GAUGE AND GAS CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove stock gas cap from fuel tank. 2. Clean and wipe inside surface of fuel tank filler cup, O-ring seal surface, and trim ring adhesive surface with a mixture of equal parts of isopropyl alcohol and distilled water. 3. See Figure 1. Install gas cap into fuel tank. is00407 Figure 1. Screw in Gas Cap is00466 Figure 2. Note Position of Arrow on Trim Ring 4. Push down on gas cap and rotate clockwise one-eighth of a turn to lock. To unlock, push down on gas cap and rotate counterclockwise one-eighth of a turn. 5. See Figure 2. Before removing adhesive backing, note position of arrow on inside diameter of chrome trim ring. NOTE As you rotate trim ring, you will see gaps between trim ring and fuel tank. Rotate trim ring to position that best eliminates gaps between fuel tank and trim ring. Rotation of trim ring should be minimal. 6. See Figure 3. With the arrow pointing toward front of motorcycle, rotate chrome trim ring slightly to determine best position of bottom chrome trim ring to contour of the fuel tank 7. See Figure 4. Mark position of chrome trim ring with masking tape or grease pencil. 8. Carefully cut masking tape with a hobby knife making sure not to scratch chrome trim ring or paint surface on fuel tank. 9. Peel off adhesive backing from chrome trim ring. 10. Using gas cap to center and masking tape (or grease pencil mark) to align, press chrome trim ring firmly into position for about ten seconds. 11. Peel off masking tape (or remove grease pencil mark) from chrome trim ring and fuel tank. 2 1 is00414a 1. Masking tape 2. Cut masking tape Figure 4. Align Trim Ring and Press into Place NOTE Allow adhesive trim ring to cure for about 5-7 minutes before you continue with kit installation. Install Flush-Mount LED Fuel Gauge 1. Remove the seat following the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove stock fuel gauge. Refer to service manual for instructions. 4. Insert wires down tube of fuel tank from LED fuel gauge. 5. See Figure 5 and Figure 6. Insert LED fuel gauge in the fuel tank cup

Incoming search terms:

HARLEY DAVIDSON PASSING LAMP TRIM RINGS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Loosen the screw from one original equipment passing lamp trim ring and remove the ring. 2. See the Service Parts illustration. Remove the screw (3) and nut (2) from the accessory trim ring (1) and set aside temporarily. 3. If not already installed, place the rubber strip (4) inside the trim ring. Align so the gap in the rubber strip is opposite the split in the trim ring as shown. 4. Insert the passing lamp sealed unit (C) inside the new trim ring and rubber strip assembly. NOTE Rotating the lamp unit may help insertion. 5. Position the bottom of the lamp unit to line up with the split in the trim ring. 6. For 2002 and later models Install the adapter ring (D) onto the passing lamp housing, lining up the tab on the ring with the notch in the lamp housing. Install the trim ring and lamp assembly onto the adapter ring, aligning the lug (or lugs) on the back of the glass lamp unit with the notches in the adapter ring. For 1962 through 2001 models Install the trim ring and lamp assembly onto the passing lamp housing, aligning the lug (or lugs) on the back of the glass lamp unit with the notches in the passing lamp housing. 7. Assemble the screw and nut to the trim ring and tighten securely. 8. Perform steps 1 through 7 for the second passing lamp. SERVICE PARTS 4 2 B C F H 3 G E 1 A D

HARLEY DAVIDSON HEADLAMP VISORS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
These kits fit all motorcycle models equipped with 7-inch headlamps. These kits do not fit models equipped with Headlamp Trim Ring Kits part numbers 69626-99, 69627-99, 69733-05, and 69734-05.INSTALLATION 1. See Figure 1. Remove original equipment bottom screw (1) and trim ring (2). Save parts for later use. 2. See Figure 3 and Table 2. Install headlamp visor (1) from kit and trim ring (A) previously removed. NOTE Make sure the screw holes in the trim ring and the headlamp assembly are aligned as it is difficult to rotate the trim ring when it is fully seated. 3. Loosely install bottom screw (C) previously removed on trim ring. Do not tighten at this time. 4. See Figure 2. Visually check to ensure that rubber bumpers on inside face of headlamp housing are not caught. 5. Snug bottom screw on trim ring and headlamp visor. 6. Rotate visor from side to side around headlamp assembly (B) if ring is caught on face of headlamp. 7. Push down on top of trim ring and push in on the bottom of the trim ring to fully seat the headlamp visor. 8. While tightening the bottom screw, continue to maintain inward pressure on bottom of headlamp visor, until screw is tight and trim ring is fully seated. 3 2 1 is00923 1. Bottom screw 2. Trim ring 3. Headlamp Figure 1. Original Equipment Headlamp Trim Ring

HARLEY DAVIDSON 5-3/ 4 INCH HEADLAMP TRIM RING INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
These kits fit 1994 and later FXLR, FXST, FXSTC, FXSTB models, 1994 and later Dyna models, 2004 and later XL883, XL883L, XL883R, XL1200L, and XL1200R models and 2005 VRSCB model motorcycles1. Loosen screw from the original equipment headlamp trim ring and remove ring. 2. Remove screw and nut from accessory trim ring assembly and set aside temporarily. 3. See Figure 1. If not already installed, place one rubber strip (2) inside trim ring (1) as shown. 4. See Service Parts Illustration. Insert the glass lens assembly (A) inside rubber strip (4) and trim ring (3), as shown. NOTE Rotating the lens may help insertion. 5. Install trim ring onto the main lamp housing (B). Assemble nut (2) and screw (1). Tighten securely. 1 2 is 01501 1. Trim ring 2. Rubber strip Figure 1. Installed Rubber Strip SERVICE PARTS See Figure 2 and Table 1

HARLEY DAVIDSON STAINLESS STEEL BRAIDED CLUTCH CABLE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
REMOVE CLUTCH CABLE 1. See Figure 1. Loosen clutch adjuster to obtain slack in the clutch cable (2) by performing the following: a. Locate cable adjuster (1) and slide off rubber boot (4). b. While holding cable adjuster with 1/2-inch wrench, loosen jam nut (3) using a 9/16-inch wrench. c. Turn cable adjuster until there is a large amount of free play at hand lever. 1 2 3 4 is 00889 1. Cable adjuster (1/2-inch) 2. Cable end 3. Jam nut (9/16-inch) 4. Rubber boot Figure 1. Clutch Cable Adjuster 2. See Figure 2. Remove the retaining ring (1), pivot pin (2) and clutch cable anchor pin (3) from the hand lever. 2 3 1 is 00891 1. Retaining ring 2. Pivot pin 3. Clutch cable anchor pin Figure 2. Clutch Cable Compoments 3. See Figure 3. Drain transmission lubricant and remove fill plug dipstick. Remove the six screws that hold the clutch release cover in place. Remove the clutch release cover, being careful not to damage the gasket. NOTE The clutch release cover gasket (P/N 36801-87B) will need to be replaced if torn or damaged to prevent transmission fluid from leaking from the release cover. 4 3 5 2 6 1 is 00894 Figure 3. Clutch Release Cover Screw Sequence 4. See Figure 4. Note position of retaining ring opening. Retaining ring opening must be positioned in approximately the same location during reassembly. Remove retaining ring (1). 5 4 1 3 2 is 00895 1. Retaining ring 2. Inner ramp 3. Cable fitting 4. Clutch cable 5. Ramp coupling Figure 4. Clutch Cable Connection 5. Pull inner ramp (2) and coupling (5) out of side cover. Hold inner and outer ramps together to keep balls from falling free. 6. Rotate the inner ramp to a position that will allow the coupling (5) to be disconnected from the inner ramp lever arm. Disconnect coupling from inner ramp. Disconnect cable end from coupling. 7. Back out threaded cable fitting from side cover. Ensure that o-ring is removed with cable. Discard o-ring. INSTALL CLUTCH CABLE 1. See Figure 4. Obtain braided stainless steel clutch cable from kit. Apply a light coat of oil on new o-ring and install o-ring (Part Number 11179) onto threaded portion of clutch cable (4). Insert clutch cable fitting (3) into clutch release cover. Do not tighten cable fitting at this time. 2. Connect cable end to coupling. Rotate ramps for best access and install coupling on inner ramp. Place ramp assembly in position in side cover. 3. Install retaining ring. Position retaining ring opening so it is located approximately over the outer ramp tang (the stop that prevents rotation). NOTE Replace clutch release cover gasket if torn or damaged. 4. See Figure 3. Place gasket, if removed, on side cover and install side cover. Tighten the six screws in the order shown to 84-108 in-lbs (10-12 Nm) . 5. Tighten the clutch cable fitting to 36-60 in-lbs (4-7 Nm) . 6. Place a few drops of oil inside cable housing. 7. Route clutch cable as follows: SOFTAIL MODELS FXSTD, FLSTS, FXSTS and FXST – Route clutch cable from the clutch release cover, across the frame, up along the front frame downtubes and across the front of the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. FLSTF and FLSTC – Route clutch cable from the clutch release cover, across the frame and up along the front frame down- tubes, up to and behind the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. DYNA MODELS FXDWG – Route clutch cable from the clutch release cover, under frame and across to the left side. See Figure 5. Insert cable (1) into clip (2) at the bottom left side of the frame

Incoming search terms:

HARLEY DAVIDSON 5-3/4 INCH HEADLAMP TRIM RING INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
These kits fit 1994 and later FXLR, FXST, FXSTC, FXSTB models, 1994 and later Dyna models, 2004 and later XL883, XL883L, XL883R, XL1200L, and XL1200R models and 2005 VRSCB model motorcycles. KIT CONTENTS See Figure 2 and Table 1. INSTALLATION 1. Loosen screw from the original equipment headlamp trim ring and remove ring. 2. Remove screw and nut from accessory trim ring assembly and set aside temporarily. 3. See Figure 1. If not already installed, place one rubber strip (2) inside trim ring (1) as shown. 4. See Service Parts Illustration. Insert the glass lens assembly (A) inside rubber strip (4) and trim ring (3), as shown. NOTE Rotating the lens may help insertion. 5. Install trim ring onto the main lamp housing (B). Assemble nut (2) and screw (1). Tighten securely

BMW PISTONS AND RINGS INSTALLATION INSTRUCTIONS

0

Filed Under (BMW) by admin on 26-10-2010

download
1. Always clean the grooves before installing rings. Carbon build-up in the groove will lead to ring “bottoming” and can result in engine seizure. 2. Check the fit of rings in the groove. A maximum of .003″ side clearance is allowable. 3. Check the cylinders for taper and out-of-roundness. Any taper of out-of-roundness will have an adverse effect on the performance of an engine. Excessive piston clearance will detract from maximum performance as well. 4. Allow ample ring gap. There is far more danger of ring butting than of an appreciable compression loss through the ring gap. Gaps, if staggered, do not cause any measurable reduction of compression. Compression rings should be fitted with a minimum of .004″ end gap per inch of cylinder deglazing. 5. Always deglaze cylinder walls before installing new rings. A 400 grit stone is recommended for deglazing. 6. All parts should be spotlessly clean before installation. Dirt in any form is the worst enemy of a hi- performance engine. You may wash all parts in hot, soapy water. Ring Gap Installation 1. Do not gap oil control rings. Start with the oil control expander. Expander Ring ends butt together. Do not overlap them. 2. Install oil control rings. Set gap 90 from where expander ring butts together. Gap top oil control ring 180 from lower oil control ring gap. 3. Install 2nd and top ring also with marks up. Stagger gaps

HARLEY-DAVIDSON V-ROD BIG BORE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
The cylinder sleeves provided with the Wiseco V-Rod big bore kit have been finished honed to size and the piston to cylinder clearance has been set. Prior to installation, the sleeves must be washed in hot soapy water (not parts washer solvent) and dried. Coat the bore surface with motor oil and wipe it with a white towel. If the towel shows any remaining grit, repeat the hot soapy water washing process until the towel will only show clean motor oil. CAUTION: Test fit the cleaned sleeve (without O-Rings installed) into the engine block. Sleeve should drop into position. If sleeve will not easily drop into position, warm the engine block with a hair dryer until sleeve will drop into position. Remove sleeve, then continue installation procedures. From the bottom side of the sleeve, gently roll the 2-cylinder sleeve O-rings into the two grooves on each sleeve. Apply motor oil to the O-rings and gently install the sleeves into the block until bottomed. CAUTION: DO NOT ATTEMPT TO INSTALL SLEEVES WITHOUT LUBRICATING THE O-RINGS. FAILURE TO LUBRICATE O-RINGS COULD RESULT IN TORN OR DAMAGED O-RINGS THAT WOULD NOT BE EVIDENT UNTIL ENGINE WAS STARTED. INCORRECTLY INSTALLED O-RINGS CAN RESULT IN CATASTROPHIC ENGINE DAMAGE. NOTE: REFER TO THE OEM SERVICE MANUAL FOR ALL TORQUE SPECIFICATIONS PISTON RING PREPARATION Wiseco V-Rod pistons incorporate an advanced 2 ring system • The top ring is file-fit, and as such, requires that the end gap must be clearanced. The proper end gap clearance is .016-.018″ with the ring installed squarely in the bore. The top ring must be installed on the piston with the dot marking toward the top of the piston. • The oil ring is comprised of the expander and two rails. Install the expander first, and then the rails. Check to make sure the expander tips have not overlapped. It is not necessary to clearance the end gaps on the oil rails. The rails should be installed without modification. PISTON INSTALLATION The Wiseco V-Rod big bore kit is supplied with pistons that are front and rear cylinder specific. Install the front piston 4792M10795 in the front cylinder with the arrow facing the front of the engine. Install the rear piston 4793M10795 in the rear cylinder with the arrow facing the front of the engine. A piston ring compressor is required to install the pistons into the cylinders. Front of engine ➔ 4792M10795 ( Front piston) 4793M10795 ( Rear piston) FWD 4793M10795 FWD 4792M10795 For further information call the Wiseco Tech Line:

2003 Honda Shadow Spirit 750 VT 750DC Custom speedometer dial installation

0

Filed Under (Honda) by admin on 06-11-2011

download
DO NOT REMOVE THE 3 PHILLIP SCREWS ON THE BACK OF THE SPEEDOMETER. This will unscrew the circuit board and the main components inside the speedometer, and possibly damage it. Just leave those 3 screws alone. They won’t make your customization any easier if they are removed. This is the hard part. Turn the speedometer face down on a soft towel on a sturdy table, bench, etc. I used a regular flat screwdriver to do this step. There is a chrome metal ring holding the glass on the speedometer. It is factory sealed. On the bottom side of this ring start prying with a flat screwdriver under the bottom lip of the metal ring. This will be a slow process (patience, patience, patience) so don’t get in a hurry and ruin the wife’s kitchen table like I did. Go around the metal ring with a flat screwdriver prying it up as straight as you can. It’s easier doing this every millimeter or two. I had to do this about 3 times all the way around the ring. After you pry the lip of the ring up all the way around enough to loosen it up considerably, gently pull the ring off of the speedometer. The glass should come off with it. Put the glass with the chrome ring aside for later. You might want to use a soft lint free towel to rest it on

Incoming search terms:

TOYOTA TACOMA 2005 D RING CARGO TIE DOWN Procedure

0

Filed Under (Toyota Manuals) by admin on 14-10-2011

download
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- — Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). — Safety (eye protection, rechecking torque procedure, etc.). — Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). — Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Hole Placement – Left Side (a) Measure vertically 70 mm up from bottom of truck bed, using marking pencil draw a small horizontal line. (Fig. 1-1) (b) Horizontally measure 72 mm from the front of truck bed, using marking pencil draw a vertical line. (Fig. 1-1) (c) Set drill stop at 1″ from drill tip. (d) Use a center punch to mark the intersection of the two lines and drill a 7/16″ hole as shown in Fig. 1-1. NOTE: Illustration is for long bed, D-cab short bed uses the same process. 2. D-ring Assembly Preparation Left Side (a) Insert the D-ring Assembly into the previously drilled hole. (b) Hold the D-ring Assembly in place by using a strip of duct tape.

Incoming search terms: