rebuilt rear master cylinder for 2005 harley sportster

You search Auto repair manual PDF rebuilt rear master cylinder for 2005 harley sportster, if there are search results will appear below. If search results do not exist, please search by others keyword.



  rebuilt rear master cylinder for 2005 harley sportster Direct Download speed 5282 Kb/s

  rebuilt rear master cylinder for 2005 harley sportster Full Version speed 6162 Kb/s



HARLEY DAVIDSON CHROME FRONT BRAKE MASTER CYLINDER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
1. See Figure 2. Drain the brake fluid. a. Open bleeder nipple cap on front brake caliper. b. Install end of a length of clear plastic tubing over caliper bleeder valve, while placing free end in a suitable container. c. Open bleeder valve about 1/2-turn. d. Pump brake hand lever to drain brake fluid. e. Remove cover. f. Close bleeder valve. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 2. Remove bolt and 2 steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) is 01010 Figure 3. 5/32 in. (4 mm) Cardboard Insert 3. See Figure 3. Place the cardboard insert between the brake lever and lever bracket. 4. Using T27 TORX® drive head, remove the 2 screws with flat washers securing the handlebar clamp to the master cylinder housing. Remove the brake lever/master cylinder assembly and clamp from the handlebar. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. Remove retaining ring from pivot pin groove at bottom of master cylinder bracket. 6. Remove pivot pin and brake hand lever from master cylinder assembly. NOTE New master cylinder comes with all internal components preassembled. It is not necessary to remove the components from the bore of the old master cylinder. See Figure 9. Use denatured alcohol to clean clutch system components. Do not use mineral-based solvents (such as gasoline or paint thinner), which will deteriorate rubber parts even after assembly. Deterioration of these components can cause clutch failure, which could result in death or serious injury. (00296a) 7. With denatured alcohol, clean and inspect all parts that will be reused. Replace as necessary and wipe dry with a clean lint free cloth

Incoming search terms:

HARLEY DAVIDSON CHROME MASTER CYLINDER AND CLUTCH BRACKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
MASTER CYLINDER REMOVAL See Figure 1. Master cylinders designed for dual disc (two caliper) operation have an 11/16 inch (17.5 mm) bore, while those that are designed for single disc (one caliper) operation have a 9/16 inch (14.3 mm) bore. The bore size is stamped (1) on the master cylinder assembly inboard of the handlebar clamp bracket. NOTE Do not use an 9/16 inch bore master cylinder assembly on dual disc (two caliper) models or dual disc 11/16 inch bore master cylinder assembly on single disc (one caliper) models. These master cylinder assemblies are not interchangeable. Using the wrong assembly can adversely affect braking efficiency or result in brake failure which could result in death or serious injury. D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1 is 01230 1. Bore stamp size location Figure 1. Verify Correct Master Cylinder Bore Size 1. Open bleeder nipple caps on front brake caliper. Install end of a length of clear plastic tubing over caliper bleeder valves, while placing free end in a suitable container. Open bleeder valves about 1/2-turn. Pump brake hand lever to drain brake fluid. Close bleeder valve. Avoid leakage. Be sure gaskets, banjo bolt(s), brake line and master cylinder bore are clean and undamaged before assembly. (00322a) 2. Remove bolt and two steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 3. See Figure 2. Place the cardboard insert between the brake lever and lever bracket

Incoming search terms:

Harley Davidson Sportster 4 Piston Rear Brake Caliper installation Manual

0

Filed Under (Harley Davidson) by admin on 02-04-2012

download
Installing Rear Caliper – Sportster Models Removing The Stock Brakes SPORTSTER REAR BRAKE SYSTEM 84 & UP MODELS The basic steps are the same to install a PM rear brake caliper kit on any of the late model Harley Davidson “swingarm” style motorcycles; all require the removal of the rear wheel. Using a suitable lift, raise the motorcycle high enough off the ground to allow you to remove the rear wheel assembly. PHOTO 2 W a r n i n g Center the motorcycle on the lift so that it will not fall while you are working on it. Photo 2: Remove the rear brake caliper assembly by unscrewing the 2 caliper mounting bolts that go through the caliper into the caliper mounting bracket. Lift the caliper up and off the mounting bracket and brake rotor, move the caliper back out of your working area. Don’t remove the brake line from the caliper yet; you will do this just before you are ready to hook it up to the new caliper. The brake pads are held into the caliper mounting bracket by 2 spring clips; slide the brake pads out of the mounting bracket and remove the retaining springs. PHOTO 3 Remove Cotter pin and rear axle nut, slide rear axle completely out. Photo 3: Remove nut from Right rear shock and rotate belt guard up. Slide belt off of pulley and roll rear wheel back 6 – 8″. Photo 4: Remove original caliper bracket from swingarm

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

HARLEY DAVIDSON CHROME REAR MASTER CYLINDER COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
1. Clean rear master cylinder cover, then remove two screws that hold cover in place. 2. Remove original cover (with sight glass) and gasket. 3. Put new cover and gasket in position. 4. Install cover screws and tighten screws (1) to 6-8 in-lbs (.7-.9 Nm). Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

Harley Davidson Road Rod Saddle Bag System Kit INSTALLATION Instructions

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
Use locktite on all fasteners!! 2. Put bike on lift and place jack under frame. Raise bike to lift rear wheel. 3. If swing arm pivot shaft is drilled and tapped on each end, they need to be redrilled and tapped to 3/8-16 to a depth of _” deep. If you are unable to drill & tap your swing arm pivot shaft, you can purchase one from Cycle Visions (part #CV6121), See Harley Davidson® V-Rod® Service Manual Section 2, Page 2.89 for removal and installation instructions. 4. Remove seat, passenger seat, turn signal module, rear fender cover, turn signal license plate assembly, and rear foot peg assemblies. NOTE: Our bag system will not work with stock exhaust system… we recommend the 2-into-1 Supertrap, or you may use any exhaust system that is lower than the rear axle bolt. 5. Remove the two upper shock bolts. Relocate the shock spacer from the right side to the left side, and use the new spacer supplied on the right side. 6. Install front bag mount between frame and spacer (see Figure 1), reinstall shock bolts and torque to 31-50 lbs. 7. Install lower bag support frame to swing arm pivot shaft using the 3/8″ bolt through rear foot peg clevis and cover (see in Figure 2). NOTE: There is a right and left covers and bag support, install accordingly. Torque to 35 foot lbs. 8. Install rear fender front mounting tabs using 8mm 1.25 x _ and flat washers (supplied in kit) (see Figure 3). 9. Install upright saddlebag support brackets to the lower bag mount assembly and lower fender extension crossover mount. (see Figure 4). Torque to 25 lbs. NOTE: Install crossover mount with gusset facing down. 10. Remove license plate light from your rear turn signal bracket license plate assembly. Install license plate light on our license plate light bracket (see Figure 5). 11. Install the license plate bracket on the inside of the rear fender extension using the top holes of the license plate frame (see Figure 6 & 7). 12. Install fender washers on the inside of the fender extension (see Figure 8). 13. Install upper fender bracket to rear fender extension with a _-20 bolt supplied in kit (see Figure 9). 14. Install rear fender extension with chrome button fitted bolts. (see Figure 10 & 11). 15. To check alignment and fit of rear fender extension reinstall original rear fender. Once you have everything lined up and fitted, remove original rear fender, drill & tap (2) two 5/16 x 18 holes in rear fender support bracket (see Figure 12). 16. Install Harley Davidson® Part #70909-95 and 47449-97 bracket and receptacle on front and rear bag supports (see Figure 13 & 14). 17. Install Harley Davidson® Part #47449-97 bracket with receptable (see Figure 14). Make sure the bolts come from the inside out. This bracket is adjustable for location.

HARLEY DAVIDSON SPORTSTER LOW REAR SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION NOTE Internal shock absorber components are not repairable beyond the Service Parts listed on this instruction sheet. Consult your Harley-Davidson dealer if further service is required. The installation procedures for this kit are the same as the original equipment (OE) installation procedures in the Service Manual. Refer to the appropriate Service Manual for the rear suspension system removal and installation procedures. The OE hardware will be re-used in the kit installation. Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) SHOCK PRELOAD (SPRING) ADJUSTMENT Refer to the appropriate Service Manual for spring adjustment. Spanner wrench (94700-52L) is required for spring adjustment. SERVICE PARTS 1 is04854 Figure 1. Service Parts: Sportster Low Rear Suspension Kit Table 1. Service Parts: Sportster Low Rear Suspension Kit Part Number Description (Quantity) Item 54734-04 Rear shock (2)

Incoming search terms:

Harley davidson Sportster Custom Straightshot Exhaust System REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove the nut that mounts the front muffler to the engine, located below the rear brake master cylinder. 4. Remove the bolt that mounts the rear muffler to the mounting bar. 5. Remove the entire exhaust system and set it aside. 6. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips . INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Vance and Hines recommends you replace your exhaust gaskets with Sceamin’ Eagle gaskets part number 17048-98. 2. Install the circlips and flanges from the stock system on to both of the new head pipes. 3. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the front head pipe using the stock nuts, do not tighten at this time. 5. Install the rear head pipe using the stock nuts, do not tighten at this time. 6. Install one muffler clamp (supplied) over the inlet (notched end) of each muffler. 7. Identify the front and rear muffler mounting brackets. The front bracket is stamped with the number 305 and the rear muffler bracket is stamped 213 . 8. Install the front muffler mounting bracket to the stud on the engine (where the stock muffler mounted) and fasten using the stock nut (leave loose at this time). The bracket will bend inward towards the center of the motorcycle when installed correctly. Note: You may need to move the wires and hoses on the lower frame rail to decrease the possibility of them chaffing on the bracket bolts. 9. Slip one of the mufflers onto the front head pipe. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the muffler to the mounting bracket using the 5/16″ flange head bolts (supplied) leave them loose at this time. 10. Attach the rear mounting bracket to the rear muffler. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the bracket to the muffler using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note: The single hole in the bracket will point downward and slightly forward when installed correctly

Indian Rocker Arm End Play Rear Cylinder/ Front Cylinder Installation

0

Filed Under (Indian) by admin on 12-11-2010

download
Rear Cylinder 1Rotate the engine so that the rear piston is at Top Dead Center (TDC), compression stroke, so no load is on the valves. 2Using a 3/16″ allen wrench, remove the four screws securing the rear cylinder rocker cover. 3Remove the cover and inspect both O-ring seals. Discard if damaged or worn. 4Push both rocker arms towards the valve end support bracket (A) and using a feeler gauge check the gap between the rocker arms and the pushrod end support bracket (B). NOTE: The Rocker arm end play specification should be between 0.003″ to 0.012″. 5 Compare the measurement to the specification an determine whether adjustment is necessary. If the end play is within specification, adjustment will not be required. Refit the rocker cover (instructions 14 to 15) and carry out the same inspection on the front cylinder . If the measurement is outside the specification, adjustment will be required and shimming will be necessary (follow the remainder of these instructions). Adjustment 6Using a 1/4″ allen wrench remove the 4 screws securing the rocker shaft assembly.Refit the LH support bracket and reposition the complete assembly on the rocker base. Make sure that the three dowels are in place and the slots in the rocker shafts are properly aligned with the mounting screw holes in the RH support bracket. 11Clean the threads of the 4 support bracket screws and apply Blue Loctite to the first 4 threads. 12Fit the 1-3/4″ screws into the LH support bracket (A) and the 2″ screws to the RH bracket (B). Torque all screws in cross pattern to 16-20 foot-pounds. CAUTION: The rear piston must be at TDC, compression stroke, when tightening the support bracket screws. 13Re-check the rocker end play to ensure it is within specifica- tion. 13Lubricate the two O-rings with clean engine oil and refit them in the grooves in the rocker base. 14Refit the rocker cover.

Incoming search terms: