remove rear brake bracket 2008 heritage classic

You search Auto repair manual PDF remove rear brake bracket 2008 heritage classic, if there are search results will appear below. If search results do not exist, please search by others keyword.



  remove rear brake bracket 2008 heritage classic Direct Download speed 5282 Kb/s

  remove rear brake bracket 2008 heritage classic Full Version speed 6162 Kb/s



1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

GL1800 Goldwing Trike Conversion Kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

Incoming search terms:

HARLEY DAVIDSON REAR BRAKE CALIPER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Prepare the Motorcycle for Service To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Follow the Service Manual instructions to disconnect the negative (-) battery cable. Remove Rear Brake Caliper Remove the Brake Pads 1. For models equipped with saddlebags: Remove the right-side saddlebag. Refer to the SADDLEBAGS section of the Service Manual. 2. Remove the rear master cylinder reservoir cover. 3. Pry both the inside and outside pads away from the brake disc and toward the caliper assembly to push the caliper pistons back into their bores. Use steady pressure to prevent scoring the brake disc. Pry between the pads and the brake disc. 4. When the pistons are fully retracted into their bores, pull the pad pins out to allow the pads to drop from the caliper assembly. Note the pads’ original orientation for installa- tion. 5. Install the cover on the rear master cylinder reservoir. NOTE Place a container under the brake caliper to catch brake fluid released when removing the brake line from the caliper. 6. Remove the banjo bolt fastening the rear brake line to the stock rear brake caliper. Save the banjo bolt for brake caliper installation and discard the two steel/rubber gas- kets. Remove the Stock Rear Brake Caliper 1. Apply isopropyl alcohol to the rubber bumper on the brake caliper to ease removal. 2. Lift the stock rear brake caliper toward the front of the motorcycle. The notch in the caliper must clear the weldment on the swing arm. 3. Remove the caliper from anchor weldment on rear swingarm. Inspect Pad and Pins 1. Inspect the brake pads. If friction material above the backing plate on either pad is 0.040 in. (1.02 mm) thick or less, replace the set. Follow the instructions in the Service Manual. 2. Inspect pad pins for wear and grooving. If wear is more than 0.015 in. (0.38 mm), replace both pins. 3. Inspect the brake disc and, if necessary, follow the instructions in the Service Manual to replace the brake disc. Install the Rear Brake Caliper NOTE Pay close attention to all warnings, cautions, and torque specifications in this instruction sheet and in the service manual when installing this rear brake caliper. NOTE Apply isopropyl alcohol to the rubber bumper for ease of installation. 1. See Figure 1. Position the caliper (1) between the brake disc and the rear fork. The weldment on the fork should fit between the notch and rubber bumper on the caliper. Verify that the full length of the rubber bumper contacts the underside of the weldment

Incoming search terms:

Yamaha V-Star 1100 Custom and Classic cruisers Floorboard/ Footpeg Extension Installation Instructions

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Start on the right (brake) side. 1) Loosen the nut at the end of the brake rod. This will allow you to unscrew the brake rod from the brake lever clevis later. 2) Pull out the cotter pin and remove the pivot pin. Unscrew the clevis 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the brake floorboard/footpeg assembly (whichever your bike has) to the frame. These bolts are torqued to 46 ft lbs, so this may be a bit difficult. 1. Loosen this nut 2. Remove the cotter pin (other side of this pivot pin) remove the pivot pin a unscrew the nut to remove the clevis nd 3. Remove these bolts When you remove the floorboard/footpeg bracket, be careful not to pull the brake switch wires loose. You may wish to cut the cable tie for more room, and then rest the bracket, with the footpeg or floorboard attached, on a short box, or block of wood, to keep it handy. Install the new brake rod, to the end of the existing brake rod. Re-install the pivot pin, and the pivot pin cotter pin. Installing the extension bar: Note that the extension bar is bolted so that it rises up in front. Use the new bolts to mount the floorboard/ footpeg bracket to the threaded holes in front. Install the Extension in the proper orientation (angled holes bolt up to the frame, with front of the bar higher than the rear – see photo) using the stock bolts for the extensions to the frame and the new bolts and washers supplied with the kit, on the forward threaded section to relocate the floorboard or footpeg bracket. The use of LocTite ® Blue here is recommended. At this point the right side Floorboard or Footpeg should be secured tightly and the brake lever hanging loose. Now install the Brake rod extension, threading the male end to the original brake rod. Don’t tighten this end yet Place the clevis over the forward most end of the brake rod extension, and threat the clevis nut onto the end of the rod. Bring the brake rod upright, to meet with the clevis at the end of the brake rod extension and replace the pivot pin. Before reinstalling the cotter pin, check the angle of the brake lever, to insure that you have the brake pedal where you want. If necessary, adjust the extension rod in or out, until you are satisfied, and then reinstall the cotter pin into the pivot pin. Check the Brake switch wire and install a new cable tie if required. Note: Due to utilizing a thicker material, 1/2″ versus 3/8″ from our competitor, the Brake rod is now positioned at a greater angle. Even with the angle, braking performance is not affected, but if you wish to bring the master cylinder in line with the brake rod, do this. Loosen the rear, and remove the front Allen bolt. Then place two washers behind the front bolt, under the bracket, and then re-install the bolts To change the angle of the brake rod, 1) loosen and remove the two master cylinder bracket Allen bolts 2) insert two washers behind the front bolt (front of the bike), behind the master cylinder bracket 3) tighten both bolts. Do not install any washers on the rear mounting hole. This will make the angle of the Brake Rod less aggressive. Step Two – Left Side For the left (Shifter) side, 1) use an open-end 10 mm wrench, to unscrew the two nuts that hold the shift rod in place. PLEASE note that one end of the shift rod has a left hand threaded nut. SAVE the nuts, as you will need them on the new longer Polished Stainless Steel Shift Rod. 2) Remove the stock shift rod. 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the shifter floorboard/footpeg assembly (whichever your bike has) to the frame.

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

Harley-Davidson Softail Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the fasteners that secure the seat. Remove seat. 6. Disconnect negative Battery Terminal. 7. Remove the Saddle Bags. And their hardware. If equipped. 8. Loosen Muffler Clamp on both Mufflers and other attaching hardware. Remove and discard both Mufflers. 9. Loosen the 4 exhaust stud nuts and save. Remove and discard head pipes and exhaust gaskets. 10. Disconnect the Rear Lamp Wiring Harness. 11. Remove any fasteners from Electrical Box. 12. Remove and discard Rear Fender, Fender Support and fasteners. NOTE: 2008-Current various models. Remove ECM from Fender and save nuts. 13. Drain all Brake Fluid from the Rear Brake System. 14. Un-clamp Rear Brake Line from the frame and Rear Fork. 15. Remove and discard both Banjo Bolts and Crush Washers from the Rear Brake Caliper and the Rear Brake Master Cylinder. 16. Remove Brake Light Switch from the Brake line, Save for reassembly. 17. Remove the Torx screw from the Brake Line bracket, Save the Torx screw for reassembly. 18. Remove and Discard Brake Line. 19. If Lower Controls option. Remove and Discard right and left floorboards/foot pegs, brake pedal, shifter, and shift linkage. Remove and Discard Passenger Foot pegs or Floorboards and their mounts. Then skip to step 24. 20. If Lower Controls Not purchased. Continue. 21. Remove acorn nut from Shift Linkage. 22. Remove 3 fasteners from Drivers Floorboard and remove. 23. Remove and discard Jiffy Stand. 24. Remove the Primary Cover by first removing the top and rear inspection cover screws. 25. Continue by removing remaining fasteners. 14 total. 26. Remove and discard Primary Cover Gasket. 27. Clean residual gasket material from both surfaces. 28. Loosen the Top Center Nut on the Primary Chain Adjuster. Lower the Primary Chain Adjuster until it rests flat on the Inner Primary Cover. 29. Remove the Clutch Lifter Retaining Ring from the Clutch Basket. Remove Clutch Lifter Assembly. 30. Using the Primary Drive Locking Tool. Loosen the Compensating Sprocket Nut. 31. Using the Primary Drive Locking Tool. Loosen the Clutch Hub Main shaft Nut. WARNING: This nut is LEFT HAND threaded. 32. Remove the Primary Drive Locking Tool, Compensating Sprocket Nut, and Clutch Hub Main shaft Nut. 33. Remove the Sprocket cover and Sliding Cam from the Crank Shaft Extension. 34. Remove the Clutch Assembly, Primary Chain, Compensating Sprocket, and Crank Shaft Extension in one assembly.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL BRAIDED REAR BRAKE LINE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) Drain Brake Fluid 1. Pop off bleeder nipple cap on the rear brake caliper. 2. Install one end of a length of plastic tubing over the caliper bleeder valve. Place the free end of the tubing into a suitable container. 3. Open the bleeder valve about 1/2-turn and pump the brake pedal to drain the brake fluid out of the rear brake system. Do not reuse brake fluid. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) Remove Existing Rear Brake Line 1. Disconnect wiring harness connectors from brake light switch spade terminals. Avoid leakage. Be sure gaskets, banjo bolt(s) and brake line are clean and undamaged before assembly. (00323a) 2. Disconnect existing brake line from rear brake caliper and rear brake master cylinder assembly. Save banjo bolts, but discard brake line gaskets. NOTE This kit contains all gaskets needed for replacement. 3. Carefully make note of rear brake line routing and orientation of banjo fittings, then remove existing brake line. Save hex head screw holding brake light switch manifold to tab on frame, but discard brake line and attaching parts. 4. Unthread brake light switch from brake line. Save switch for later use.

Incoming search terms:

HARLEY DAVIDSON DYNA REAR STOP/ TAIL/ TURN SIGNAL RELOCATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2011

download
PREPARATION NOTE Position the motorcycle upright using a suitable lift or jack. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow instructions to remove the main fuse. 2. Follow the service manual instructions to remove the seat. 3. Raise the rear of the vehicle to allow access to the underside of the rear fender. LICENSE BRACKET AND ILLUMINATOR REMOVAL For Models WITHOUT a Center Tail Lamp NOTE See Figure 1. The reflector mounting block (2) is held to the fender (1) with double sided tape. Remove with care to avoid scratching paint. 1 3 2 5 4 6 7 is06256 1. Rear fender 2. Rear reflector and mounting block 3. Wire channel (2) 4. License plate bracket mount 5.5/16-18 screw (2) 6. License plate illuminator 7. M4 screw (2) Figure 1. Rear Fender, Models Without Center Tail Lamp 1. Remove the rear reflector and mounting block (2) from the underside of the rear fender (1). 2. Remove the license plate from the vehicle (if installed). Retain the plate and attaching hardware. NOTE Before removing rear wiring, note wire routing. -J04856 1 of 10 3. Remove the rear lamp wiring from behind the wire channels (3) on the underside of the fender. 4. Disconnect the two-way license lamp connector [93] and the four-way right [18] and left [19] stop/tail/turn (STT) lamp connectors from the STT module in the area under the seat. 5. Remove the two 5/16-18 screws (5) retaining the license plate bracket mount assembly (4) to the fender support. 6. Remove the license plate illuminator (6) from the license plate bracket mount assembly. Save the illuminator. The bracket mount (4) and four screws (5, 7) can be discarded. 7. Proceed to License Bracket and Illuminator Assembly . For Models WITH a Center Tail Lamp NOTE On these models, the license plate illuminator is part of the center tail lamp and is not removed. 1. Remove the three screws retaining the license plate bracket to the tail lamp housing. Remove the bracket and set aside for later assembly. 2. Proceed to Rear Lamp Wiring, For Models WITH a Center Tail Lamp and RED Stop/Turn Signals or AMBER Turn Signals . LICENSE BRACKET AND ILLUMINATOR ASSEMBLY For Models WITHOUT a Center Tail Lamp 1. See Figure 7. Get the new license plate bracket (3), illuminator cover (4), spacer (6) and two M4 screws (5) from the kit, and the license plate illuminator (A) removed from the original equipment (OE) license plate bracket. 2. See Figure 2. Assemble the illuminator (1), spacer (2) and cover (3) to the license plate bracket (5) in the sequence shown, and tighten the screws (4) securely. 3. Get the STT relocation weldment (6), two screws (7) and two flat washers (8) from the kit. 4. Apply a few drops of Loctite 271 – Red to the clean screw threads. Assemble the license plate bracket to the weldment as shown, and tighten the screws to 120 in-lbs (13.6 N-m) . NOTE If using a metal tool to install the black nuts, protect the finish with cloth or paper to prevent damage. 5. Loosely install the black painted nuts (9) onto the threaded studs on each side of the STT relocation weldment. 6. Remove the wires and socket terminals from the two-way license plate illuminator socket housing. Set the socket housing aside for later installation

Incoming search terms:

Harley Davidson Sportster 4 Piston Rear Brake Caliper installation Manual

0

Filed Under (Harley Davidson) by admin on 02-04-2012

download
Installing Rear Caliper – Sportster Models Removing The Stock Brakes SPORTSTER REAR BRAKE SYSTEM 84 & UP MODELS The basic steps are the same to install a PM rear brake caliper kit on any of the late model Harley Davidson “swingarm” style motorcycles; all require the removal of the rear wheel. Using a suitable lift, raise the motorcycle high enough off the ground to allow you to remove the rear wheel assembly. PHOTO 2 W a r n i n g Center the motorcycle on the lift so that it will not fall while you are working on it. Photo 2: Remove the rear brake caliper assembly by unscrewing the 2 caliper mounting bolts that go through the caliper into the caliper mounting bracket. Lift the caliper up and off the mounting bracket and brake rotor, move the caliper back out of your working area. Don’t remove the brake line from the caliper yet; you will do this just before you are ready to hook it up to the new caliper. The brake pads are held into the caliper mounting bracket by 2 spring clips; slide the brake pads out of the mounting bracket and remove the retaining springs. PHOTO 3 Remove Cotter pin and rear axle nut, slide rear axle completely out. Photo 3: Remove nut from Right rear shock and rotate belt guard up. Slide belt off of pulley and roll rear wheel back 6 – 8″. Photo 4: Remove original caliper bracket from swingarm

Incoming search terms:

Incoming search terms: