remove victory exhaust

You search Auto repair manual PDF remove victory exhaust, if there are search results will appear below. If search results do not exist, please search by others keyword.



  remove victory exhaust Direct Download speed 5282 Kb/s

  remove victory exhaust Full Version speed 6162 Kb/s



GL1800 Goldwing Trike Conversion Kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

SUZUKI M109 1800 cc EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 10-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System. 6. Remove the dust cover from the solenoid to expose the rotating cam and cables. DO NOT TRY TO ROTATE THE CAM RELATIVE TO THE ACTUATOR SELENOID TO REMOVE THE CABLES; DOING SO MAY DAMAGE THE INTERNAL COMPONENTS OF THE SOLENOID. To remove the cables from the cam, use the slack in the cables obtained in Step 5 to disengage the cable barrels from the cam, see Figure 1. THE DUST COVER WILL NOT BE REINSTALLED. 7. Now prepare the exhaust valve actuator solenoid for reuse. SECURELY HOLD THE CAM TO PREVENT IT FROM ROTATING IN THE SOLENOID. WHILE PREVENTING THE CAM FROM ROTATING, remove the 10 – 32 flange bolt securing it, see Figure 2. Replace the cam with the Cobra supplied cam, BE SURE TO PREVENT THE CAM FROM ROTATING WHEN REINSTALLING THE BOLT, OTHERWISE DAMAGE MAY OCCUR TO THE SOLENOID , see Figure 3. Torque to factory specifications.

SUZUKI M109 1800 cc FRONT/REAR EXHAUST / HEATSHIELD INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set collar and grommet aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve actuator solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System

2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

Related Item : how to remove triumph motorcycle fron wheel (1)