removing ais plugs yamaha roadstar

You search Auto repair manual PDF removing ais plugs yamaha roadstar, if there are search results will appear below. If search results do not exist, please search by others keyword.



  removing ais plugs yamaha roadstar Direct Download speed 5282 Kb/s

  removing ais plugs yamaha roadstar Full Version speed 6162 Kb/s



2001-2003 YAMAHA XV16 MODELS FACTORY MODIFICATION CAMPAIGN

0

Filed Under (Yamaha) by admin on 02-12-2010

download
Fuel Pump and Carburetor Removal: •Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers. Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring.

Incoming search terms:

YAMAHA ROADSTAR TRIKE Removal of Clear Taillights and installation of Red Taillights

0

Filed Under (Yamaha) by admin on 16-02-2011

download
1 Installation of Lights 1.1 Support the trike on jack stands and remove the wheels. 1.2 Remove the clear lights from the inside of the wheel wells by unscrewing the three (3) screws from the light. 1.3 Unplug the wires and remove the lights. 1.4 Remove the chrome bezels and rubber gaskets from the clear lights and install on the red lights (5 screws). 1.5 Re-connect the wire plugs and install the red lights to the trike body using the same three screws. 1.6 Replace the wheels and torque the lug nuts to 75 lb.ft. 2 Wire modification inside trunk 2.1 From the inside of the trunk pull back the carpet on both the left and right hand sides to expose the wire harnesses coming from the wheel wells. 2.2 Locate the resistors in the harness, 2.5″ x 0.5″ x 0.5″, and covered by black shrink wrap. 2.3 Cut the shrink wrap to expose the resistors and cut wire on both side of the resistors. Remove and discard resistors. 2.4 Splice in the supplied 5″ green wires (WITHOUT the diodes) with 2 blue scotchlock connectors per side to reconnect the cut wires. 2.5 Do not glue in carpet until lights are tested. 3 Change to pigtail from Trike to Motorcycle. 3.1 Remove driver’s sear 3.2 Unplug pigtail from motorcycle (MC) wiring and trike body wiring. 3.3 Cut heat shrink on the MC plug side of the pigtail and pull expansion sleeve back to expose the wires. Figure 1 3.4 Cut Green and Yellow turn signal wires and about 3″ from the MC plug and splice in Green and Yellow wires from the supplied resistors with the supplied hest shrink solder connectors (heat to be applied) – (three wires in one connection) Figure 1 3.5 Cut the Red (Brake) and Brown (Running lights) wires and splice in the supplied diodes with the supplied heat shrink solder connectors. Red side of the diode wire facing the Trike plug. Figure 1 3.6 Connect eye lug on the black wire from the resistors to the negative terminal of the battery. Figure 2 3.7 Plug pigtail back into the Trike body and the MC

Incoming search terms:

YAMAHA ROADSTAR/ WARRIOR ADJUSTABLE REAR LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Secure motorcycle to a bike lift and raise the motorcycle. Rear wheel should remain barely resting on the ground. 2. See diagram on page 2 for references made in parentheses, for example (#5). 3. Remove the nut from the rear suspension bolt (#5) at the bottom of the shock (#7). You may need to remove your exhaust and rear horn to access the nut and bolt. 4. Remove this suspension bolt (#5) from the non-exhaust side of the bike. You may need to raise or lower the bike to ease the tension on the bolt in order for it to come out. 5. Next remove the nut (#4) and bolt connecting the relay arm (#3) to the swingarm. From here remove the entire shock assembly and relay arm from the bike. For ease of re-installing the relay arm (Step 8) and shock be sure to take precautions that in removing the assembly, you can put it back the same way you took it off. Flipping of the relay arm can cause serious damage to the lowering kit and surrounding components. 6. Remove the two suspension arms from the relay arm(#3) and shock(#7). Compare stock arm to length of lowering arm you are about to install. Make sure the length of the lowering arm matches the link of the stock arm. To set how much you want to lower the bike, lengthen the lowering arms. Every 1/4″ longer than stock is approximately 1″ of drop. Do not lower the bike more than 2″ for safety reasons. To adjust, unscrew the large hex shaft from the threaded rods. Make sure to adjust length equally on both shafts. Be sure to tighten all jam nuts once desired lowering position is set. 7. Re-assemble the lowering arms to the top of the shock (#7) using the supplied collar, nut, and bolt. The stock collar (#6), the one in the eyelet at the top of the shock (#7), will need to be removed as it is too long. (This is because the heims are thicker than the stock arms) Do not tighten the nut, or re-install into the frame yet. 8. Re-install the relay arm (#3) to the swingarm. The large hex shafts go to the rear of the bike. This is where it

Incoming search terms:

1999-2010 Yamaha Roadstar 465 Series Single Shock Supplement

0

Filed Under (Yamaha) by admin on 14-02-2011

download
Mount the shock as you would your stock shock per your authorized shop manual (with the rebound adjustment at the bottom) noting the following: n Remove the horn located on the lower left side. Also remove the Remote Adjustable Pre-Load adjuster knob by removing the screw located in the center of the knob, then pull it straight off. n As you mount the shock, feed the Remote Adjustable Pre-Load adjuster through the opening behind where the horn was located on the left side of the bike – see figures 2 and 3. Do not loosen or attempt to rotate the line between the shock and the adjuster. n Reinstall the adjuster knob, and torque the screw to 50 in/lbs. (5.65 N-m). n Make sure the shock rebound adjustment is at the rear facing the left side of the motorcycle and the pressure valve is facing up. n Tighten shock bolts to the proper torque specifications (refer to your manual). n Mount the adjuster to the supplied mounting bracket using the supplied M6-1.0X8mm SHCS fasteners and torque them to 80-90 in/lbs (9-10 N-m). Then mount the bracket to the bike using the stock two drive-belt cover bolts – as shown in figure 4. n Using the supplied zip-ties, secure the hydraulic line away from any moving parts or heat sources. Reinstall horn. To adjust the ride height, simply turn the adjuster knob clockwise (looking at it from the back of the bike) to increase the height and counterclockwise to reduce it. See main instructions for procedure of achieving optimum ride height

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

YAMAHA ROADSTAR 1600/1700 POWERSHOTS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 22-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Remove both frame covers. Remove the left cover first to access a bolt that holds the right side cover in place. 2. Remove right side floorboard assembly held in place by two bolts (Figure 1). 3. Remove exhaust port Allen nuts. 4. Remove Allen bolts securing rear muffler to exhaust system mounting bracket. 5. Remove complete exhaust system. Begin by lifting muffler out of mounting bracket locating hole (assistance may be required). 6. Check condition of stock exhaust gaskets. Replace if damaged or worn 7. Remove two bolts attaching stock exhaust mounting bracket to frame. 8. Remove hose clamp securing rear brake hose to exhaust mounting bracket. 9. Remove brake hose banjo bolt from rear caliper. 10. Slide hose out of loop in bracket. 11. Check condition of sealing washers on banjo bolt and replace if damaged or worn. 12. Reconnect brake hose to caliper (without bracket) and torque Banjo bolt to 25 lbs. ft. 13. Brake system must be bled or brake will not operate correctly. Refill reservoir after bleeding 1. Remove exhaust system and heat shields from protective packaging. Place exhaust on a non-abrasive surface such as a blanket or carpet. Using a non-permanent marker or tape, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through (Figure 2). 2. Attach brake hose clamp to mounting bracket (stamped 362-P) using one 6x16mm flange bolt and nylock nut (supplied) to tab located on top of bracket (Figure 2). 3. Install mounting bracket using two 10x30mm Allen bolts and lock nuts (supplied)(Figure 3). 4. Carefully slide heat shields onto headers.

Incoming search terms:

YAMAHA V-Star 1100 Motorcycle Enhancements Remote Oil Filter Installation Manual

0

Filed Under (Yamaha) by admin on 10-11-2010

download
Removing Your Old Filter and Beauty Cover In order to install the new Remote Oil Filter Kit, you’ll need to remove the stock Yamaha “beauty cover” and the old filter and filter cover. Remove the engine parts necessary to access the stock filter as outlined in the V-Star owner’s manual. The parts should come off in this order: 1. Muffler assembly 2. Front exhaust pipe 3. Rear brake reservoir cover bolt and brake cover (the reservoir should not be removed, it can remain in place and be moved aside as needed) 4. Right floorboard (this can be simply loosened, by loosening the two bolts underneath) With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. There are five Allen bolts holding the beauty cover (so named, because most of the cover just covers the chromed side of the engine There are five bolts holding the cover. Ignore the three on the “Yamaha” cap in the middle – these just hold the Yamaha cap to the beauty cover itself. One bolt is hidd – in this picture – just be the Yamaha ca en low p. The bottommost bolt on the beauty cover will likely leak some oil when you remove it – it holds on the inner oil filter cover. Once you remove the beauty cover, you can remove the oil filter cover, and the oil filter Keep these two “O” rings, you’ll need them for the remote kit Old oil filter. Toss it away; you’ll never need one again! Throw away the old filter, and carefully remove the orange and black “O” rings from the filter cover (see picture above). These two “O” rings will go on the new engine cap in the same order as on the old filter cover. “O” ring for bottom bolt. When the beauty cover and filter cover are removed, be sure not to lose the tiny “O” ring that the bottom bolt goes through. Preparing the Remote Oil Filter Kit Remove the orange and black “O” rings from the stock filter cover plate, and place them on the Remote Oil Filter Kit engine cap – black on the inside, orange on the outside – just like on the stock filter cover.

YAMAHA YFM 350 Removing stock carburetor and cables.

0

Filed Under (Yamaha) by admin on 19-01-2012

download
Remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Preparing motor for carburetor install 1. Remove stock manifold from cylinder head. 2. Place supplied o’ring into aluminum flange as pictured in figure 1. Figure 1. 3. Install aluminum and rubber flange to motor using supplied bolts. See Figure 2. The shorter 25mm bolt will need to be placed in the bottom hole. IMPORTANT NOTE: Install the aluminum flange with the o’ring towards the motor and the thick side up.

YAMAHA RAPTOR 350 Removing stock carburetor and cables

0

Filed Under (Yamaha) by admin on 18-01-2012

download
remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Stuff a clean, dry rag into manifold to keep debris out of motor. 4. Remove stock air box. 5. Remove choke cable from handlebars. 6. Remove carb vent line from bike. Carburetor installation 1. Carefully trim the rubber alignment tab off of the face of the manifold with a razor blade or side cutters. 2. Remove the hex pipe plug from the carb cap using a 11mm or 7/16 wrench. Do not discard plug, as it will be needed later. Install the metering adjustment tool included in the hardware kit. Do not over-tighten as damage may occur to cap. 3. Attach fuel line to carburetor and secure with clamp. 4. Install remote idle cable into tab on top of carburetor. See main manual for this step. NOTE: Nut must be removed from cable before installation 5. Place carburetor into manifold

Incoming search terms:

2001-2003 XV16 Fuel Pump and Carburetor Removal

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers.       Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding    the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY
PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring. NOTE: The collar has a bevel on its inside diameter     for the O-ring facing inward and a bevel on the outside diameter facing the pulley. •Remove the drive and driven sprockets with chain as an assembly. •Remove the collar and O-ring. NOTE: Collar has a bevel on its inside diameter that faces inward for the O-ring. •Remove oil tank filler neck. •Remove the relay bracket on the right-hand side. NOTE: Leave the relays connected. Simply move them out of the way to allow room for transfer case removal. •Slide the transfer case out from the right side.

Incoming search terms:

Incoming search terms: