removing gas tank on 2007 kawasaki vulcan 900

You search Auto repair manual PDF removing gas tank on 2007 kawasaki vulcan 900, if there are search results will appear below. If search results do not exist, please search by others keyword.



  removing gas tank on 2007 kawasaki vulcan 900 Direct Download speed 5282 Kb/s

  removing gas tank on 2007 kawasaki vulcan 900 Full Version speed 6162 Kb/s



HARLEY DAVIDSON FLUSH-MOUNT LED FUEL GAUGE AND GAS CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove stock gas cap from fuel tank. 2. Clean and wipe inside surface of fuel tank filler cup, O-ring seal surface, and trim ring adhesive surface with a mixture of equal parts of isopropyl alcohol and distilled water. 3. See Figure 1. Install gas cap into fuel tank. is00407 Figure 1. Screw in Gas Cap is00466 Figure 2. Note Position of Arrow on Trim Ring 4. Push down on gas cap and rotate clockwise one-eighth of a turn to lock. To unlock, push down on gas cap and rotate counterclockwise one-eighth of a turn. 5. See Figure 2. Before removing adhesive backing, note position of arrow on inside diameter of chrome trim ring. NOTE As you rotate trim ring, you will see gaps between trim ring and fuel tank. Rotate trim ring to position that best eliminates gaps between fuel tank and trim ring. Rotation of trim ring should be minimal. 6. See Figure 3. With the arrow pointing toward front of motorcycle, rotate chrome trim ring slightly to determine best position of bottom chrome trim ring to contour of the fuel tank 7. See Figure 4. Mark position of chrome trim ring with masking tape or grease pencil. 8. Carefully cut masking tape with a hobby knife making sure not to scratch chrome trim ring or paint surface on fuel tank. 9. Peel off adhesive backing from chrome trim ring. 10. Using gas cap to center and masking tape (or grease pencil mark) to align, press chrome trim ring firmly into position for about ten seconds. 11. Peel off masking tape (or remove grease pencil mark) from chrome trim ring and fuel tank. 2 1 is00414a 1. Masking tape 2. Cut masking tape Figure 4. Align Trim Ring and Press into Place NOTE Allow adhesive trim ring to cure for about 5-7 minutes before you continue with kit installation. Install Flush-Mount LED Fuel Gauge 1. Remove the seat following the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove stock fuel gauge. Refer to service manual for instructions. 4. Insert wires down tube of fuel tank from LED fuel gauge. 5. See Figure 5 and Figure 6. Insert LED fuel gauge in the fuel tank cup

Incoming search terms:

HARLEY DAVIDSON CHROME FUEL TANK TRIM PANEL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
INSTALLATION 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat. Retain all seat mounting hard- ware. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) 2. See the Figure 5. Remove the original fuel filler cap (A) from the tank and set it aside. Obtain a small diameter Harley-Davidson fuel filler cap (B) and screw it into the fuel filler opening. For Model XL883C, or other models equipped with Genuine Motor Parts Large Capacity Fuel Tank 3. To ensure surface cleanliness, clean the top of the fuel tank with a mixture of 50 to 70% isopropyl alcohol and 30 to 50% distilled water. Allow to dry thoroughly. 4. Measure and mark the centerline of the fuel tank, with a wax pencil or water-based marker, at the rear of the tank as shown in Figure 3. Proceed to Step 10. For Model XL1200C 2 1 is 01910 1. Original fuel tank trim panel liner 2. Fishing line (or string) Figure 1. Removing the Existing Trim Panel (XL 1200C) 5. See Figure 1. Insert the fishing line (2) between the rear of the fuel tank and the liner (1) on the underside of the original trim panel. NOTE Raise the ends of the fishing line away from the fuel tank to avoid scuffing the tank finish 6. Using a side-to-side “sawing” motion, work the fishing line toward the front of the fuel tank to break the adhesive bond between the trim panel and the tank. 7. Carefully pull the trim panel and liner off of the tank and discard it. NOTE Be careful not to scratch the paint on the fuel tank when removing the adhesive

Incoming search terms:

BUELL ACCESSORY GAS CAP KIT INSTALLATION MANUAL

0

Filed Under (Buell) by admin on 29-03-2011

download
Installation NOTE When performing the following Steps, use the Fuel Tank Vent Valve Installation Kit (Part Number 91432-96Y). This kit consists of: * Fuel Tank Vent Valve Installation Aid * Fuel Tank Vent Valve Fitting Socket To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect battery cables, negative cable first. An open flame or spark may cause a fuel tank explosion if all traces of fuel are not purged from the tank. Use extreme caution when servicing fuel tanks. Gasoline is extremely flammable and highly explosive. Do not smoke or allow open flame or sparks anywhere in the area when working on fuel system components. Inadequate safety precautions could result in death or serious injury. 2. Remove gas cap. 3. Carbureted Models: Drain fuel tank. Disconnect hose clamp and fuel supply hose from fuel supply valve and drain fuel into suitable, clean container. See applicable Service Manual, Section 4 for complete, detailed procedure. Fuel Injected Models: Relieve pressure from fuel system. See applicable Service Manual, Section 4 for complete, detailed procedure. Drain fuel tank. a. Using suitable external fuel pump, such as a Gas Caddy, pump fuel from tank and into a suitable, clean container. b. See instructions for external fuel pump for correct use. 4. See Figure 1. Cut cable tie securing vent hose to fitting and remove vent hose from fuel tank. Even with the fuel tank completely drained, a small amount of gasoline may leak from the bore when the fuel supply valve is loosened or removed. Thoroughly wipe up any fuel immediately and dispose of rags in a suitable manner. Gasoline is extremely flammable and highly explosive. Inadequate safety precautions could result in death or serious injury. 5. If the fuel supply valve requires cleaning or repair, refer to applicable Service Manual, Section 4, for complete, detailed procedures. 6. See Figure 1. Remove the fuel filler cap and O-ring. 7. Remove the eight self-tapping screws from fuel clamp flange and remove fuel cap flange

Incoming search terms:

2000-2002 Aprilia Mille INSTALLATION INSTRUCTIONS

0

Filed Under (Aprilia) by admin on 26-10-2010

download
1) It is a good idea to use Blue Loc-tite on all bolts you are about to remove and replace. 2) This kit has extremely close tolerances and in order for all the parts to clear the triple clamp and gas tank, you will probably have to loosen and align most of the associated bolts. We have tried very hard to make this as compact as possible but we know the factory tolerances vary from bike to bike. Be patient, the results are worth it. 3) Remove both front fuel-tank retaining bolts. You will use the longer bolts provided in our kit. 4) Install the frame bracket (part #22-6036-03) that mounts to your front (2) tank bolts holes. The frame bracket sits on top of the stock tank spacers. The frame bracket is offset. This means it fits correctly only one way, with the offset toward the triple clamp, part numbers facing forward, (see photo below). Due to the tight clearances on this model you’ll want to be sure the frame bracket does not make contact with the tank itself. It’s easier to start the tank bolts if you lift up on the tank slightly, while starting the new bolts into their threaded hole. Tighten the new tank bolts to 6 ft lbs. and use Loc-tite. 5) Remove the large 14mm Allen nut and washer that holds your triple clamp on. You will not re-use either one. 6) Install the new “Triple clamp damper mount” Part # 22-2925-00 into the recess area where the stock Allen head bolt was sitting. There is a machined recess or built-in-washer on the bottom of our mount to match the recess on your triple clamp. The 2 nubs that hang down, should match the rear contour of your triple clamp precisely. Use loc-tite and retighten the new 14mm Allen nut provided to your factory torque specs, usually a minimum of 35 ft lbs. and maximum of 85 ft. lbs. Do not use the stock washer that was under the original 14mm nut. 7) Grease the tower pin and drop it in the tower pin hole portion of the frame bracket. The tower pin is designed to “float” and requires no retaining devices. Keep the tower pin lightly greased! It should not touch the gas tank on the bottom side. 8) Install the stabilizer using the (2) 6×20 Allens with the slot in the link arm matching the tower pin. 9) Since the tank is rubber mounted at the rear, you want to be sure it won’t push forward and rub the frame bracket. After riding the first time, be sure the tank has not shoved forward by your body making contact with it. Remember, under heavy braking your entire body weight is pushing the tank forward. Until you have verified sufficient clearance between the tank and the tower pin, it might be smart to put something between the tank and tower pin to protect the tank. 10) Read your damper manual for initial settings on the controls. The damper is infinitely adjustable and totally up to the user to find their preference. Start with softer (counter clockwise) settings. Normally where we set the unit, at 8 clicks out on the base valve, is a good starting point.

Ducati Hypermotard Large Fuel Tank Installation Instructions

0

Filed Under (Ducati) by admin on 26-10-2010

download
REMOVING THE OEM FUEL TANK GO FOR A RIDE The best way to remove fuel from your original fuel tank is to RIDE your bike. You should already be familiar with how low you can go and the less fuel that’s in your tank before you start means the less mess you make when draining it. HM69 Fuel Tank Installation Instructions This manual is provided for marketing and informational purposes only and is a guide to assist experienced motorcycle technicians with the installation of the HM69 fuel tank. This installation involves gasoline. Improper installation, adjustment, alteration, service or maintenance regarding the HM69 fuel tank can cause property damage, personal injury or death. At-home Do-It-Yourself mechanics should not install the HM69 fuel tank if you are uncertain of your ability to properly install it and refer the installation to an authorized Ducati service department. ! REMOVE THE SEAT Remove the seat bolt at the rear of the seat with a 4mm hex key. To remove the seat, grasp both sides of the seat, lift the rear of the seat slightly, and pull the seat to the rear of the bike. The front of the seat engages onto bolts on either side of the fuel tank and can be stubborn. THIS KIT ALSO CONTAINS: © 2009 California Cycleworks, Inc. Questions? Email orders@ca-cycleworks.com 1
REMOVE THE BODYWORK The tank cover is fi rst. Remove the fuel fi ller cap and then the 4 screws you see: 2 near the front of the cover and the two aside the fi ller neck. Lift up on the forward portion of the cover and move the entire cover rearward so that the back of the cover is away from the retaining contour on the fuel tank. SIDE PANELS Remove the right side panel’s inner cover using a large coin. Both left and right side covers are retained by 3 screws with 4mm hex heads. Remove the 2 screws on the side of the tank (which were revealed with the removal of the seat). While holding the side covers to support them, remove the bottom screw. The left side cover pulls away naturally – take care not to drop the cover as the tool kit is housed inside of it, adding unexpected weight

KTM Superduke 990 MotoHooligan Airbox Installation

0

Filed Under (KTM) by admin on 26-01-2012

download
Undo the screws retaining the left and right front tank spoilers and remove. Fitment of Motohooligan airbox is possible without removing the tank but task is much easier if this is done. Access for removal of SAS system and installation of PC111 is also much improved and it’s worth the additional 5 minutes work. It would also be a good idea to do this with an empty tank so it’s lighter to handle. Unscrew front retaining bolt from front of tank and lift tank to access the spring damper on the left hand side. On standard Superdukes release the two circlips, carefully support tank and remove damper unit. (NB. SDR model not fitted with damper). Lower tank back into position and unscrew one of the pivot bolts at rear of tank Stage 1 – remove spoilers and tank Note : Fuel line has a connector half way between tank and airbox. but leave it in position to support the tank whilst you unscrew the other side. Once both bolts are unscrewed tank is free but still attached by fuel lines and electrics. Lift the rear of the tank to expose the two electrical plugs and disconnect both making sure that the retaining pins are pushed in first before you pull them apart. Reaching underneath the rear of the tank you’ll see the fuel line running into the base of the airbox. Half way down there is a connector with a metal button. Press this and pull the fuel line apart – you might want to have a rag handy to catch any fuel drips. Pull off the breather tube at the front, (on US models also pull off the breather that leads to the charcoal canister in the tail), and lift the tank away

HARLEY DAVIDSON LEATHER FUEL TANK PANEL INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION Softail Models NOTE Generic leather tank panel shown for illustration purposes. 1. Refer to Owner’s manual for removal of seat. 2 3 1 is00927 1. Instrument panel 2. Nut 3. Masking tape Figure 1. Leather Fuel Tank Panel Installed 2. See Figure 1. Remove nut (2) securing instrument panel (1). Gently lift instrument panel up and turn it so stock fuel tank panel front end is uncovered. 3. Place a shop towel under instrument panel and set instrument panel on fuel tank. 4. See Figure 2. Remove lower mounting screw and washer (1) and retain for reinstallation. 5. Lay leather tank panel on tank in desired position. 6. Install screw and washer saved in Step 4 into hole on tank panel. Tighten screw finger tight. 1 is02467 1. Save screw and nut for reinstallation Figure 2. Softail Tank Panel Installs With Original Screw And Nut 7. See Figure 1. Install instrument panel (1) and tighten nut (2) to 8 ft-lb (11 Nm) . 8. Tighten lower mounting screw. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 9. Install seat on the motorcycle by inserting the tab at front of seat into slot at the rear of fuel tank. Secure seat to fender with screw. INSTALLATION FXDWG and FXDC NOTE Generic leather tank panel shown for illustration purposes. 1. Refer to Owner’s manual for removal of seat. 2. 1993-2003 Models: Figure 1. Remove nut (2) securing instrument panel (1). Gently lift instrument panel up and turn it so stock fuel tank panel front end is uncovered. 2004 and later Models: See Figure 4.

Incoming search terms:

KAWASAKI VULCAN 900 SLASH CUT STAGGEREDS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
1. Attach mounting bracket 440-P to frame using two stock fl ange head bolts used on stock upper bracket (Figures 1 and 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through (Figure 3). 3. Lay front header, and rear header into their head heat shields and muffl er body heat shields. 4. Install #20 hose clamps (supplied) on heat shields and #36 (supplied) on muffl er body heat shields by feeding tail end of clamps into heat shield clips (fi gure 3). Take note of clamp screw head direction (Figure 4). Screw heads must be accessible when system is installed on motorcycle for adjustment purposes. NOTE: Do not tighten at this time. 5. Using stock fl ange nuts, carefully install head pipes into exhaust ports. Assistance may be required. NOTE: Do not tighten at this time. 6. Slide nut plates inside bracket that is welded to backside of muffl er bodies (Figure 5). While holding nut plates in place, attach muffl er bodies to mounting bracket 440-P using two 5/16″x 5/8″ fl ange head bolts (supplied). Leave them loose at this time. 7. Align muffl er bodies so they are level and parallel when viewing from the right side of the bike. Tighten cylinder port exhaust fl ange nuts on front and rear cylinders. 8. Tighten the fl ange bolts on both muffl ers. 9. Tighten all heat shield clamps. 10. Check for adequate clearance of all exhaust system components and motorcycle accessories prone to heat damage. NOTE: For models with fl oorboards, two Spacer washers are supplied to space out the fl oorboard bracket enough to allow the fl oorboard to fold up without hitting the heat shield. 11. Be sure to tighten all hardware before starting your motorcycle. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. NOTE: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up

Incoming search terms:

KAWASAKI VULCAN 900 CLASSIC specifications

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
Engine type Four-stroke V-Twin Displacement 903cc Bore x stroke 88 x 74.2 mm Compression ratio 9.5:1 Valve system SOHC, 8 valves Cooling system Liquid Fuel system Digital Fuel Injection with dual 34 mm throttle bodies Ignition TCBI with digital advance Starting Electric Transmission 5-speed Final drive Kevlar belt Frame type Double-cradle, high-tensile steel Rake/trail 32º/164 mm (6.5 in.) Suspension, front 41 mm hydraulic telescopic fork Suspension, rear Single shock with 7-way preload adjustment Tire, front 130/90-16 Tire, rear 180/70-15 Brakes, front/rear Single 300 mm disc with 2-piston calipers/ 270 mm hydraulic disc with 2-piston calipers Wheelbase 1645 mm (64.8 in.) Seat height 680 mm (26.8 in.) Fuel capacity 20 litres (4.4 gal.) Curb weight* 281 kg (619 lbs.) Warranty 12 month

Incoming search terms:

Kawasaki Vulcan 900 Installation and Removal Manual

0

Filed Under (Kawasaki) by admin on 25-04-2012

download
1) Place motorcycle on its side stand on a firm level surface. 2) Remove saddlebags if applicable 3) Attach bracket C (left side) and bracket D (right side) to rearmost fender attachment bolt. A) If bike has no saddlebags use 3/8 spacer between bracket and motorcycle. Use new bolt provided. B) If bike has stock saddlebags use enclosed threaded rod assembly. 1) Thread rod into rear bag/fender mount 2) Place 3/8 spacer and bracket onto rod 3) Tighten down with locknut ensure locknut and rod are tight 4) Replace bags on rod and tighten NO BAGS STOCK BAGS
4) Remove rear riders pegs and attach front of bracket A(left side) and bracket B (right side) to rear foot peg mounting point. Mount foot peg to outside of bracket. Use new bolts provided. 6) Attach brackets C/D to top of rear hitch plate. 7) Attach rear of brackets A and B to TOP of hitch arms 8) Ensure hitch is square on motorcycle and tighten all bolts

Incoming search terms:

Incoming search terms: