removing hardware from wrist

You search Auto repair manual PDF removing hardware from wrist, if there are search results will appear below. If search results do not exist, please search by others keyword.



  removing hardware from wrist Direct Download speed 5282 Kb/s

  removing hardware from wrist Full Version speed 6162 Kb/s



HARLEY DAVIDSON FLSTC & FLSTS DOCKING HARDWARE WITH SADDLEBAG SUP- PORTS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
The rear docking points in kit part number 90366-03 provide the rear mounting points for the Solo Rack. The rear mounting points from this kit ( 53931-03A ) will need to be installed to provide the clearance for the Solo Rack to be mounted. Table 2. Turn Signal Relocation Kit Requirement Turn Signal Relocation Kit Required Accessory Part Number 2003 and later FLSTC Not required 53815-00 Detachable Sideplates Not required 53066-00A Detachable Tour Pak Rack REMOVAL FLSTS Saddlebag Assembly Removal 1. See Figure 15. Remove a saddlebag by removing the acorn nut and washer on the lower support and the two flange locknuts inside the bag. Discard the flange locknuts but retain the acorn nut and washer. 2. See Figure 1. Remove the saddlebag support studs and their mounting hardware. 3. Repeat steps 1 – 2 on the other side of the vehicle. FLSTC Saddlebag and Fixed Mount Sissybar Removal 1. See Figure 15. Remove a saddlebag by removing the acorn nut and washer on the lower support and the two flange locknuts inside the bag. Discard the flange locknuts, but retain the acorn nut and washer. 2. See Figure 1. Remove the saddlebag support studs and their mounting hardware. 3. Remove and discard fixed mount sideplates. Retain sissy bar for use with detachable sideplates. 4. Repeat steps 1 – 3 on the other side of the vehicle. 1 is06914 1. Saddlebag support studs Figure 1. Original Equipment Hardware (FLSTS model shown) INSTALLATION Docking Hardware Installation – For Detachable Sideplates or Tour-Pak Rack NOTE See Figure 15. The rear docking point (8) is wider than the front docking point (2). -J02425 1 of 5 1. Place front docking point (2) on front stud (1), with countersunk end of docking point facing fender support. 2. Place spacer (6) for side plates or mid docking point (for detachable sideplate kit) on rear stud (1). 3. Place rear docking point (8) on bolt (7), with countersunk end facing fender support. 4. Insert front stud (1) through front docking point (2), fender support and into bracket underneath fender as shown. 5. Insert rear stud (1) through fender support and into bracket underneath fender as shown. 6. Install bolt (7) through fender support and into bracket underneath fender as shown. 7. Tighten front and rear studs (1) and bolt (7) to 27 ft-lbs (37 Nm) . 8. Repeat steps 1-7 on the other side of the vehicle.

Incoming search terms:

Harley-Davidson Big Twin Evolution and Twin Cam Edelbrock/ JE Sport INSTALLATION INSTRUCTIONSsman Pistons

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION PROCEDURE Note: All Evolution® “Big Twin” pistons are marked “Front” or “Rear” and come with rings, wrist pins, and locks. • Note: We highly recommend that a dealer or trained mechanic perform the installation of these pistons. Specialized equipment is required for honing and finishing the cylinders to ensure long life of the piston and cylinder assembly. 1. Remove original equipment cylinders from engine. Refer to a shop manual or other reference book for specific steps, if needed. (Note: Care should be taken not to bend the studs or damage the cylinder during removal of the cylinders.) 2. With a small screwdriver, move the wrist pin retainer around to gain access to the tail of the retainer as it lines up with the notch in the bottom of the wrist pin hole. 3. Use a small screwdriver, pick or awl to roll the wrist pin retainer out of its groove. 4. Push wrist pin out and remove piston. 5. Repeat procedure for the other piston. 6. At this point, take cylinders, new pistons, and piston-to-wall clearance specifications to your dealer or machine shop to perform necessary machining operations. • IMPORTANT NOTE (Evolution® and Twin Cam®): The cylinder bore must be machined/honed to provide .0025″ of piston-to-wall clearance. Measure the piston diameter at a point .500″ up from the lower skirt (See Figure 3). 7. Starting with the front cylinder, install new piston rings and one wrist pin retaining clip (Note: Second ring has a dot which must face up when the ring is installed) . 8. Place the piston over the conecting rod, making sure that the intake valve pocket is towards the intake side. (For Evolution ® , see Figure 1. For Twin Cam ® , see Figure 2) . Coat the wrist pin with engine oil and insert it into the piston. Install the second wrist pin retainer into the groove. 9. Lightly coat the piston skirt with engine oil. Place a piston ring compressor over the piston/ring assembly and compress. Place the cylinder over the piston and gently push down until all rings are in the cylinder. Remove the ring compressor, and push the cylinder the rest of the way down. (Note: Be careful not to get oil onto the base gasket.) 10. Place two nuts and washers on opposite corners of the #1 cylinder to hold it down while you repeat the procedure for cylinder #2. 11. Assemble the rest of the engine per factory specifications. Start the engine and let it run at 2000 rpm for about 10 minutes.

Incoming search terms:

HARLEY DAVIDSON HARDWARE/ TURN SIGNAL RELOCATION KIT FOR SPORTSTER LEATHER SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
Installation Instructions for 79052-04 and 79073-04 Do not exceed 7 lbs (3.17 kg) maximum load in each saddlebag. Additional weight can affect a motorcycle’s stability, handling characteristics, and safe operating speed which may lead to an accident resulting in death or serious injury. NOTE A pick tool (Snap-on TT600-3) will be required for 1996 and later models for removing and reinstalling a multi-lock amp con- nector. NOTE A Service Manual for your vehicle is available from your Harley- Davidson Dealer. Installation – Hugger Models Only (1994-1997) To perform the following steps for Hugger Models only, fender and frame must be sufficiently supported, as both shocks will need to be removed at the same time. An improperly supported vehicle could result in death or serious injury. A Service Manual is needed to install this kit. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson Dealer perform the installation. Improper installation of this kit could result in death or serious injury. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove seat, sissy bar and sideplate, if applicable. Retain hardware for reinstallation. Disconnect battery, negative cable first. 2. Properly support motorcycle under frame to prepare for removal of right and left shocks. 3. Remove rear buttonhead screw on each side of fender. 4. See Figure 1. With rear fender and frame securely supported, remove left and right shocks by removing upper nut (2), washer(s) (3) and shock cover (4). Remove bolt (6), washer (7) and locknut (8) at lower shock mount. Remove shock

HARLEY DAVIDSON CHROME TRANSMISSION HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cable, negative (-) cable only. NOTE The starter does not need to be removed to install this kit. 2. Remove exhaust system only if needed to access transmission top cover hardware. Refer to Service Manual for instructions. NOTES Replace existing zinc hardware with chrome-plated hardware one at a time so the transmission top and side covers do not need to be replaced. 3. Remove and discard existing six 1/4-20 x 1 in. hex socket- head screws and washers from top transmission cover. Install six chrome hex socket head screws (1) and washers (2) on top transmission cover (3). Tighten to 84-108 in-lbs (9.5-12.2 Nm). 4. Remove and discard existing two 1/4-20 x 1 in. hex socket head screws and washers from side transmission cover. Install two chrome hex socket head screws (1) and washers (2) on side transmission cover (5). Tighten to 84- 108 in-lbs (9.5-12.2 Nm). 5. Remove and discard existing four 1/4-20 x 1-1/2 in. hex socket head screws and washers from side transmission cover. Install four chrome hex socket head screws (4) and washers (2) on transmission side cover (5). Tighten to 84- 108 in-lbs (9.5-12.2 Nm). 6. Install exhaust system if previously removed. Refer to Service Manual for instructions. 7. Connect negative (-) battery cable

Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

HARLEY DAVIDSON FLHR SEATS Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
Kits 52981-98A and 51102-01A fit 1997 and later FLHR and 1998 and later FLHRCI model motorcycles. Kits 52059-97A and 52918-98A are designed for installation on 1997 and later FLHR and 1997 and later FLHT motorcycles with trim piece kit number 52447-96 installed. Kit 52934-98A fits 1997 and later FLHR, and FLHRCI motorcycles. This kit also fits 1997 and later FLHT and 1998 FLTR when installed with trim piece kit number 52447-96. See Service Parts illustration for kit contents. Installation When performing the following installation procedures, be cautious not to scratch painted surfaces (fender, tank, etc.) with metal seat tabs or tools. 1. Remove left saddlebag from motorcycle. Save all hardware for reinstallation. Remove existing grab strap from left side of vehicle by removing bolt and forward saddlebag mounting bracket. Note the mounting orientation of the grab strap, saddlebag mounting bracket and hardware for installation of the new grab strap. 2. Secure new grab strap to left side of vehicle by reassembling forward saddlebag mounting bracket and bolt to vehicle in same orientation as they were removed. Tighten bolt enough to hold assembly in place. 3. Remove screw (with lockwasher) and nylon flat washer from rear of passenger pillion. Pull pillion rearward to remove pillion from motorcycle. Retain screw (with lockwasher) and nylon washer. 4. Remove rear bracket from pillion by removing two bolts. Install rear bracket with bolts on new seat. 5. Remove seat mounting studs securing rider seat to fender. Remove seat from motorcycle. 6. Install new seat making certain that bracket on front of seat fully engages into seat mounting tab on frame. 7. Secure seat onto rear fender using nylon washer and screw (with lockwasher) removed in step 3. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 8. Remove right saddlebag from motorcycle. Save all hardware for reinstallation. Remove existing grab strap from right side of vehicle by removing bolt and forward saddlebag mounting bracket. Note the mounting orientation of the grab strap, saddlebag mounting bracket and hardware for installation of the new grab strap

Incoming search terms:

HARLEY DAVIDSON FENDER SUPPORT COVER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
REMOVAL NOTE Complete all removal and installation procedures on one side before performing on the other side. 1. See Figure 1. Remove rear turn signal assembly (2) following the instructions in the service manual. Save all hardware for installation. 2. Remove the upper shock absorber hardware (3) following the instructions in the service manual. Save all hardware for installation. 3. Remove the rear fender support cover (4) following the instructions in the service manual. Save all hardware for installation. INSTALLATION 1. See Figure 1. Install the rear fender support cover (4) with the stock hardware. Tighten finger-tight. 2. Install the rear turn signal assembly (2) following the instructions in the service manual. 3. Install the upper shock absorber hardware (3) following the instructions in the service manual. 4. Remove the rear fender support cover hardware and apply Loctite Threadlocker and Sealant 243 (Blue) to the threads of the screws. Tighten screws to the specifications in the service manual. 5. Thoroughly clean the mounting surface of the fender support cover with an equal mixture of water and isopropyl alcohol. Peel the paper backing from the new reflector and install reflector (1). Press the reflector firmly. Allow AT LEAST 24 hours after applying the reflectors before exposing the areas to vigorous washing, strong water spray or extreme weather

HARLEY DAVIDSON DYNA DOCKING HARDWARE FOR FXDX WITH WIDE TIRE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
Installation NOTE Perform the following procedures on one side of the motorcycle until instructed to go to the other side. To keep fender in alignment the front docking point will be mounted first. INSTALLING DOCKING POINTS NOTE Save the acorn nuts and washers removed from the fender support bracket for use when installating docking points. 1. Loosen and remove the acorn nuts, washers, and screws from the fender support (right-hand) bracket. Save the washers and acorn nuts for docking point installation. Discard screws. 2. Obtain 1 plastic bushing, labeled 01, from a bushing set. 3. Place the bushing (4) (beveled side out) into the front support hole as shown in Service Parts illustration. 4. Place the countersunk side of the front docking point (2) so that it engages bushing (4). 5. From underneath (inside) the fender, insert hex-head screw (1) through fender, support bracket and front docking point (2). 6. Install washer (7) split lockwasher (5) and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 7. Obtain another plastic bushing, labeled 01 , from the bushing set. 8. Place bushing (4) (beveled side out) into the the rear support hole as shown in Service Parts illustration. 9. Place the countersunk side of the rear docking point (3) so that it engages bushing (4). 10. From underneath (inside) the fender, insert hex-head screw through fender, support bracket and rear docking point (3). 11. Install washer (7) split lockwasher (5)and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 12. Repeat procedures 1 through 11 for opposite (left-hand) side of the motorcycle. NOTE In time docking points may wear, causing the sideplates to become loose. The fit may be tightened using the following procedure. 1. Loosen docking hardware. 2. Rotate docking points clockwise approximately 45°. 3. Tighten docking hardware to the appropriate torque values. Repeat as often as required, up to 3 times

Incoming search terms:

HARLEY DAVIDSON PRIMARY COVER CHROME HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
INSTALLATION Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the negative (-) battery cable from the battery. Disconnect the positive (+) battery cable from the battery. 2. Replace existing zinc hardware with chrome plated hardware one at a time so the primary chaincase and clutch cover gasket do not need to be replaced. 3. Consult the Service Manual for screw locations and torque values. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 4. Connect the positive (+) battery cable to the battery. Connect the negative (-) battery cable to the battery

HARLEY DAVIDSON FXSTD DETACHABLE WINDSHIELD AND DOCKING HARDWARE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
INSTALLATION NOTE Use the Docking Hardware Kit to assemble two upper and two lower clamps. See the Service Parts illustration. The upper clamps use a mounting pin (4) and the lower clamps use a button head screw (5) to fasten the windshield mounting bushing. 1. Assemble the windshield docking hardware as follows: a. Install a larger chrome washer (6) and bushing (7) onto a button head screw (5). Thread the screw into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. b. Install a larger chrome washer (6) and bushing (7) onto a mounting pin (4). Thread the pin into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. 2 1 3 4 4 5 is 02187 1. Upper clamp 2. Lower clamp 3. Fork tubes 4.1/8 inch (3 mm) approximately 5.3.0 inch (76 mm) Figure 1. Installing Clamps NOTE Place shop rags on the headlamp, front fender and front of the fuel tank to prevent scratches to these components. Be sure the windshield assembly does not contact chrome or painted parts. Contact will cause scratches to chrome or painted parts. 2. See Figure 1. Install a lower clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the top of the lower triple clamp, then finger tighten the lock nut. Repeat with the second lower clamp and fork tube. NOTE Keep front wheel straight to prevent brackets from scratching fuel tanks. See Figure 1. Install the clamps on the fork tubes so the bushing center lines are 3 inches (76 mm) apart. 3. Install an upper clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the bottom of the upper triple clamp. Ensure that the center lines of the upper and lower bushings are 3 inches (76 mm) apart, then finger tighten the lock nut. Repeat with the second upper clamp and fork tube

Incoming search terms: