removing swing arm for belt replacement harley softail

You search Auto repair manual PDF removing swing arm for belt replacement harley softail, if there are search results will appear below. If search results do not exist, please search by others keyword.



  removing swing arm for belt replacement harley softail Direct Download speed 5282 Kb/s

  removing swing arm for belt replacement harley softail Full Version speed 6162 Kb/s



Harley Davidson Softail Drive Side Brake System Installation Manual

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
Removing The Stock Components Although the PM Drive Side Brake System can be installed with the swing arm bolted to the frame, we recommend removing it for better access as well as repainting. Begin by removing rear wheel,stock brake components and belt guard from swing arm. Photo #1 Using supplied 3/4 x 2″bolt,position Drive Side BrakeAssembly on swing arm. Slide assembly to center position of tab and axle spans. Making sure brake mounting tabs are flush with swing arm,snug 3/4 x 2″ bolt to hold assembly and mark swing arm area to be ground Photo #2 . Remove entire assembly from swing arm and thoroughly grind paint away from marked areas Photo #3 . Photo #4 Re-mount assembly to swing arm and slide to rear-most position of both axle and brake mounting tabs. Confirm that brake tabs are flush with swing arm and parallel to each other. Snug 3/4 x 2″bolt and 5/16″socket head cap screws in tabs to hold assembly during welding process. Warning Center the motorcycle on the lift so that it will not fall while you are working on it. Photo #6 Photo #5 Photo #7 Photo #9 Welding Tabs to Swing Arm Note PM recommends all welding be done by a certified welder. Photo #5 Tack weld rear of tabs to swing arm. Avoid excessive welding near brake as- sembly as heat can mar finish. Loosen socket head cap screws and 3/4″bolt,Slide entire assembly to forward most position and re tighten bolts Photo #6 (movement should require minimal effort if tabs are aligned properly) and tack front of tabs to swing arm. Remove brake assembly from swing arm. Weld tabs to swing arm.Verify alignment of tabs, as they must remain parallel to each other. Repaint swing arm and re-install on bike to factory torque specs. Installing Brake Assembly Remove primary bracket from tower assembly (this allows bracket to be installed without having to line up caliper on disc) by removing the three 5/16″socket head cap screws (commonly called allen bolts). Photo #7 Mount rear tire and bolt pulley to rear wheel. Place disassembled bracket against pulley using smaller of two supplied spacers between bracket and pulley. Slide wheel/brake assembly into swing arm. Place large spacer on right side and slide axle in. Do not tighten axle at this point . Photo #8 Slide caliper/tower assembly over disc and install 5/16″x 1″socket head cap screw in center hole to position assembly Photo #9 . Snug, but do not tighten bolt at this point.

Incoming search terms:

1987 to Current Harley Davidson Softail (FLST Only) Motorcycle Trike Conversion removal and Installation Guide

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
Removal of Original Parts Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. • Seat (to be re-installed without modification). • Left and right saddle bags (if so equipped). • Left and right rear crash bars, saddlebag rails (if so equipped). • Left and right passenger foot rests (to be re-installed without modification) • Complete exhaust system (to be replaced with new system). • Rear wheel NOTE: Prior to removing rear wheel, depress foot brake and secure in down position (e.g., zip-tie to floor board). This will prevent fluid flow when rear brake caliper is removed • Remove Rear Caliper (disconnect brake line at caliper) NOTE: Cap line to prevent introduction of dust / debris into line. Remove caliper. • Rear Drive Pulley (1987-99 models to be re-installed without modification). • Rear Fender (2000 and newer models, fender mount plates to be reused). • Swing Arm NSTALLING TRIKE CONVERSION KIT 3.1 Sprockets and Drive Belts Specifications See following table for belt installation (1987-99 will use a 4 tooth longer belt) Note : See OEM manual for belt replacement procedure. Year Drive Sprocket OEM Belt New Belt / Sprocket 1987-92 70 T 132 T 136 1993-94 61 T 128 T 132 1995-99 65 T 130 T 136/70TOEM 2000-06 Champion Sprocket, 70 T 135 T Use OEM 2007 Up Champion Sprocket, 66 T Use OEM 3.2 Install Swing Arm É Noting size and location of bolts, remove Cross Assembly from Champion Swing Arm. Do not discard hardware. Figure 1 3.2.1 1987-99 Model Years • Remove bearings from OEM Swing Arm using OEM shop tools and hydraulic press. Note : Although original bearings can be re-used, it is HIGHLY recommended that NEW bearings be installed to Champion Swing Arm a. b. Press bearings into Champion Swing Arm in the same way as the OEM Swing Arm. Using OEM Spacer Tube and supplied washers (four ¾” flat washers), install Champion Swing Arm using OEM bolt, outside washers and nut. Do not torque pivot bolt nut at this time. Figure 2 Note : Insure belt path is over and under Swing Arm pivot. c. d. Replace cross assembly and hardware (previously removed in step 3.2) to Champion Swing Arm. Note that the 2 upper left hand side bolts are countersunk. Torque pivot bolt to OEM specification

Incoming search terms:

Harley-Davidson EMERGENCY DRIVE BELT REPLACEMENT KIT Installation Manual

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Shift transmission to neutral. Before installation of the emergency belt, to avoid personal injury and/or vehicle damage, secure the motorcycle. Both stand and motorcycle must be on solid, level ground. Failure to follow instructions could result in death or serious injury. 2. See Figure 1. Remove spring clip (4) (if present) and loosen rear axle nut (1). 3. Loosen rear axle adjuster (3) (or adjuster nut, if so equipped) on each side of motorcycle, and move rear wheel to full forward position. 4. Remove the damaged/broken belt. 5. Inspect sprockets and belt guard (2) for damage and/or debris. Remove any debris. If sprockets and belt guard are not damaged, proceed with the installation. 6. Remove belt guard. 40171-97,40146-00 1 WARNING i06186 Figure 1. Axle 1. Axle nut 2. Belt guard 3. Adjuster 4. Spring clip 2 4 1 3 7. See Figure 2. Install feeder strip on emergency belt. 8. Feed strip around transmission sprocket in a counterclockwise direction over frame cross support. 9. See Figure 3. Interlock the “v” ends of the emergency belt. a. Insert a hex socket key in the fourth (4) and ninth (6) tooth holes. b. Place the splice block (2) over the seventh (5) tooth hole. c. Install a socket head set screw (3) in the seventh tooth. Tighten using another hex socket key. d. Move the block to the next tooth, and repeat installation steps (b) and (c) in each tooth until all 12 screws are installed. NOTE There are 16 screws included in this kit. However, only 12 screws will actually be installed in the belt. The remaining four screws are spares. 10. See Figure 4. Grasp the emergency belt at the mid point of the lower run between your thumb and forefinger and lift the belt up to take up any slack in the belt. Measure the distance that the belt deflects (2) under tension (1). When two pounds of tension is applied to the lower run of the emergency belt, the belt deflection should be within the following measurements

Incoming search terms:

HARLEY DAVIDSON Softail Big Shots Staggered Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. If equipped, loosen the floor boards to gain clearance for exhaust removal and installation. 2. Loosen heat shield clamps on both the front and rear head pipes. 3. If equipped, loosen crossover pipe clamp, located between front and rear head pipes. 4. Remove two cylinder exhaust port flange nuts from each head pipe, located at the cylinder head. 5. Remove the bolts that attach mufflers to the frame. 6. Remove the complete exhaust system and set aside. Assistance may be required. 7. Remove stock mounting bars and brackets. 8. On models equipped with upper mounting bar attached at swing arm pivot bolt, go to step 9. If upper mounting bar is attached with two torx bolts (not swing arm bolt) go to step 10. 9. Remove right side 1/4″-20 bolt which holds lower fender in place. The fender will flex outwards allowing removal of right passenger foot peg bolt. Park the motorcycle on its side stand. Position a floor jack under right hand frame tube of the motorcycle below swing arm pivot bolt. Raise jack just enough to take the weight off swing arm pivot bolt. Remove swing arm pivot bolt and stock upper mounting bar. Replace swing arm pivot bolt and torque to 120 ft. lbs. Reinstall passenger foot peg using 1/2″-20 x 3″ bolt and 1 5/8″ long spacer (supplied). Reinstall 1/4″-20 fender bolt. 10. Using a T50 torx driver, remove the three mounting bolts and mounting bar. (Two of the bolts are visible, the third also attaches right hand passenger foot peg pivot and is accessed by removing foot peg. Reinstall foot peg using 3/8″x 2-1/2″ Allen bolt and 3/4″ long spacer (supplied). 11. Carefully remove exhaust port flanges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. (Recommended replacement exhaust port gaskets, Harley part number:17048-98 or 65324-83A)

Incoming search terms:

HARLEY DAVIDSON SOFTAIL CHROME LOWER BELT GUARD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
REMOVING STOCK PLASTIC LOWER BELT GUARD 1. See Figure 1. Remove the hex head bolt (2), washer (3), acorn nut (5), hex head screw (4) and acorn bolt (8) attaching plastic belt guard to rear fork. 2. Remove the plastic belt guard. Save fasteners (2), and (4), washer (3), acorn nut (5) and acorn bolt (8) for installing new chrome belt guard. INSTALLING CHROME LOWER BELT GUARD 1. See Figure 2. Position the new chrome belt guard from kit over belt. Align the holes in guard with mounting lugs on rear fork. Install acorn bolt (9) through mounting lug and fasten to belt guard. Finger tighten only. 2. Install screw (4) with washer (5, from kit) through belt guard and fasten to threaded mounting lug. Position the guard for adequate clearance and finger tighten screw. 3. At the upper belt guard, install the original forward hex bolt (2) and original washer (3) through the upper guard (1), then through the upper hole in chrome belt guard and through mounting lug on rear fork. Secure with original acorn nut. 4. Tighten all hardware to 110 in-lbs (12.4 Nm)

BMW R850, R1100, R1150, R1200 Oilhead Maintenance Manual

0

Filed Under (BMW) by admin on 16-11-2010

download
cold Engine and Drivetrain Procedures Check Alternator Belt Tools Parts T-handle hex – 4mm none Note: In most cases the alternator belt does not need to be checked any more. Early models should have the pulley and belt upgrade that came out a few years ago. Current recommendations are that the belt is installed and adjusted, then not disturbed until 36K when replacement is specified. 1. Remove the four bolts holding the black plastic alternator belt cover at the front of the engine, 4mm T-handle hex. 2. Remove the cover by sliding it straight down. 3. Check the belt for cracks or shredding. 4. Check the belt tension, quite tight, ~1/4″ deflection when you press on the center. Note: Paul Glaves suggests that proper belt tension is when you can twist the belt ~90 degrees, midway between the pulleys. If you can twist it more than 90 degrees, it is too loose. If you cannot twist it 90 degrees, then it is too tight. 5. Leave the cover off for the valve adjustment procedure on the next page. Change Alternator Belt Tools Parts T-handle hex – 4mm alternator belt socket – 13mm ratchet wrench – 13mm torque wrench 1. Remove the four bolts holding the black plastic alternator belt cover at the front of the engine, 4mm T-handle hex. 2. Remove the cover by sliding it straight down. 3. Loosen the 2 nuts and 1 bolt, 13mm, that hold the alternator – one is on top and one is on each side, thus allowing the alternator to pivot down. 4. Remove the old belt. (Some bikes have a pipe that traps the belt – loosen it enough to get the old belt out and the new belt in) 5. Install the new belt being sure it is properly seated. 6. BMW calls for a tensioning torque of 5.9 ft.lb. (8 Nm) on the adjuster bolt on the left side of the bike. You have to get at this bolt from the alternator side and you may have to lift the tank. Alternatively, you can pry the alternator up with a large screwdriver to tension the belt. 7. Once the belt is under proper tension, tighten the 2 nuts and 1 bolt, 13mm, to 15 ft.lb. (20 Nm). 8. Check the belt for proper tension (see above) and proper seating alignment

Incoming search terms:

HARLEY DAVIDSON SECONDARY BELT EMERGENCY KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
The 40101-80 kit, with a 126 tooth belt, fits: •1980-1986 FXB and 1984-1986 FXWG models This kit may also be used on 1989-1992 international Softail models with a 127 tooth belt. The 40171-97 kit, with a 130 tooth belt, fits: •1995 and later domestic Softail models •1994 and later international Softail models •1994 and later international Dyna models The 40109-86 kit, with a 132 tooth belt, fits •1986-1992 and 1994 domestic Softail models •1989-1993 international FLT and FXR models This kit may also be used on the following models with 133 tooth belts: •1991 and later domestic Dyna models •1991-1992 international Dyna models •1994-1995 international FLT models The 40100-85 kit, with a 136 tooth belt, fits: •1985-1994 domestic FXR models •1985-1996 domestic FLT models •1996 international FLT models The 40112-97 kit, with a 139 tooth belt fits •1997 FLT models Installation 1. Put transmission in ‘Neutral’. 2. Loosen rear axle nut. Loosen rear axle adjuster nut on each side of motorcycle, and move rear wheel to full forward position. 3. Remove the damaged/broken belt. 4. Inspect sprockets and belt guard for damage and/or debris. Remove any debris. If sprockets and belt guard are not damaged, proceed with the installation. 5. See Figure 1. Remove belt guard. 6. See Figure 2. Install feeder strip on emergency belt. Feed strip around transmission sprocket in a counterclockwise direction over frame cross support.

Incoming search terms:

Harley-Davidson BIG-TWIN 8mm BELT DRIVES (OPEN OR CLOSED) INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
INSTALLATION : The spacer behind the front pulley should be removed prior to installing the belt drive. This spacer may or may not be required to correctly align the pulleys. If a spacer is needed for alignment, various sizes are available from your local Primo Belt Drives dealer (part number PX-1 =package of 6 various sizes). With all supporting components installed, install front pulley, lubricate and reinstall the clutch hub. Loop the belt around the front and rear pulleys, and gently push into place. Use the washer and nut supplied with the kit on the front motor shaft, (always use an impact wrench on splined shaft motors) tighten to 80-100 foot pounds of torque. After installing and adjusting clutch, track the belt by turning the pulleys. If needed us a straight edge between the front and rear pulleys to check alignment. Improper alignment of the pulleys will result in reduced belt life. Spacing the motor pulley outward will cause the belt to track towards the outer primary cover. If spaced too far out the belt will rub on the inside of the clutch shell. ENCLOSED INSTALLATIONS: The same disassembly is required, with the exception of the clutch hub and inner primary. We recommend using our PC-1000-Acomplete clutch assembly. Loop the belt around both pulleys to insure that you have the proper belt for your pulleys, then gently push the unit into place. Use the washer and nut supplied with the kit on the motor shaft. Torque the motor nut to 80-100 foot pounds . Adjust the clutch & check belt / pulley alignment. Before installing the primary cover be sure that everything inside clears both the outer and inner covers. In some cases a small amount of metal may need to be removed from one or more of the bosses on the inner or outer primary covers

BMW Poly-V Belt – R 1100 Models

0

Filed Under (BMW) by admin on 16-11-2010

download
Information: In an effort to reduce service volume, a maintenance-free ribbed Poly-V belt was adopted on all R1100 models from engine number 38946130 onwards (09/94 production onwards). This belt does not need to be retentioned (even at the 600 mile service). The old belt required replacement every 24,000 miles. The new style belt is to be replaced every 36,000 miles. Use the same torque procedure as the old belt. Replacement of an old style belt with the new maintenance free belt requires the use of the new parts below: Parts Kit: 12 31 1 342 086 (kit consists of the following) In addition to the Poly-V belt, the following parts were also changed: 1. Top pulley new: steel old: Aluminum 2. Bottom pulley new no spot welds: old: steel w/three spot welds on front 3. Belt new: Ribbed, printing on belt (1342059 Fa. Dayco) or (1341779 Fa. Conti) Slight squeaking may be heard for a short time after a cold start when temperature is below 50°F. The belt should reach it’s correct operating tension soon after the start up. The belt only needs retentioned if the slight squeaking does not stop after warm up.

HARLEY DAVIDSON CHROME UPPER BELT GUARD KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION NOTE When performing the following step, it is not necessary to completely remove the shock mount bolt, back the bolt out only until it is flush with the swingarm. 1. See Figure 1. Loosen the left rear shock mount bolt (1) and back it out until the threaded portion of the bolt is flush with the swingarm. 1 2 is03762 1. Shock mounting bolt (left side) 2. Belt guard Figure 1. Loosen Shock Mounting Bolt 2. Pull the belt guard (2) straight back toward the rear of the bike to remove the guard from upper and lower grommets. See Figure 2. It may be necessary to work the guard up and down slightly to dislodge it from the upper (1) and lower (2) grommets. Remove the belt guard and discard. 2 1 3 is03763 1. Upper grommet mount 2. Lower grommet mount 3. Front belt cover Figure 2. Rubber Grommet Mount Locations 3. Obtain the chrome belt guard from kit. While making sure belt guard is over the belt, slide the guard straight in between the shock and sprocket and align cover just below front belt cover (3). The cutouts in the bracket should be lined up to engage with upper and lower grommets. NOTE When performing the following step, gently pull the guard in and out at the center; it should feel fairly tight even though the rear mounting bracket has not been secured. 4. See Figure 3. Firmly push the guard toward the front of the bike until the cutouts are secured by the grommets and the belt guard mounting bracket (1) hole lines up with the shock bolt

Incoming search terms: