removing yzfr125 top yoke

You search Auto repair manual PDF removing yzfr125 top yoke, if there are search results will appear below. If search results do not exist, please search by others keyword.



  removing yzfr125 top yoke Direct Download speed 5282 Kb/s

  removing yzfr125 top yoke Full Version speed 6162 Kb/s



SHOCK CUTAWAY SADDLEBAG INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 10-11-2010

download
1. Saddlemen saddlebags mount over the back of the seat or rear fender of most motorcycles. When properly installed there will be one saddlebag on each side of the motorcycle with the split yoke resting on the fender or the seat. Both saddlebags must be securely mounted and tied down in a manner that does not interfere with any part of the motorcycle’s operation. Be certain the saddlebags or their mountings do not contact brake components, turn signals, taillight, brake light, suspension, swingarm, or drivetrain. These Shock Cutaway saddlebags have been designed to fit over your bike’s shock absorbers (see Fig. A), which allow for larger bags on bikes otherwise limited by shock and turn signal location. 2. We highly recommend that your bike be equipped with Saddlemen’s S4 saddlebag supports (see Fig. B) or equivalent. Saddlemen also offers Quick Disconnect rigid-mounting hardware kits for most bikes, that allow easy on, easy off bag installation and eliminate the yoke. For more information, see your dealer or contact Saddlemen at 310- 638-1222. 3. Your saddlebags must be at least two inches away from any exhaust pipe while the motorcycle is stationary or moving. You can adjust the split yoke to change the height of the bag on the motorcycle by adjusting the position of the hook and loop fastening system (Fig. C). Adjust the split yoke shorter to raise the height of the saddlebags, and longer to lower the height of the saddlebags. The split yoke can also be reversed by unbolting each yoke half from each saddlebag, and reversing the yoke’s position on your bike. This allows for the offset in the yoke to be positioned either forward or backwards providing clearance for the motorcycle’s components (Fig. D). 4. In addition to the hook and loop fastener, the bags rely on a nylon safety strap system to ensure proper and secure installation. This strap must be used, and tightened snugly. Assure that the strap’s short end with D-rings is pushed through the slot in the split yoke and resting on the topside it. Once the split yoke is set to the proper position, run the long safety strap over the top of the split yoke and secure it to the D-rings (see Fig E and F), and tighten it. 5. Once you’ve placed the saddlebags on your bike and have them adjusted properly, use the straps located on the bottom of each saddlebag (see Fig. E and G) to connect the saddlebag to the saddlebag support (if you are using Saddlemen’s S4 Saddlebag bracket refer to the instructions shipped with it). These lower straps adjust in length to assure a tight fit. Wrap them around the saddlebag support, snap the buckle halves together, and adjust the length of the strap assuring the strap is tight and supporting some of the saddlebags’ weight. Repeat this step on the other saddlebag.

Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

HARLEY DAVIDSON CRUISER II SADDLEBAG MOUNTING INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
a. Adjust the mounting yoke by first removing the lacing system that secures the two yoke halves. b. Move the two yoke halves inward or outward until the saddlebags ride as high as possible on both sides of the motorcycle. When properly adjusted, both bags will hang parallel to one another. c. Utilizing the lacing pattern shown in both images (A ) and (B ) , reinstall and fasten the lacing system. The lacing must pass through a minimum of four sets of adjustment holes on the mounting yoke. WARNING: Saddlebags must never contact the rear wheel, drive train or exhaust. A minimum clearance of two inches, with the suspension compressed, is necessary at all times. CAUTION: Tour Master saddlebags do not fit under the seat of all motorcycles. Please check your motorcycle’s factory supplied owners manual for under saddle mounting compatibility and proper seat removal and installation. II. MOUNTING STRAP INSTALLATION: a. With the yoke properly adjusted, attach each of the four mounting straps (C ) and ( D ) to a rigid portion of the frame or rear rack assembly. b. Connect the quick-release buckles and pull the adjustment straps tight. c. Secure excess strap tether with the integrated hook and loop fastener

Bajaj Removing And refitting Automatic Cam Chain Tensioner

0

Filed Under (Bajaj) by admin on 31-10-2010

download
1. Remove the 2 Flanged Bolts securing the Tensioner Assembly. 2. Remove Tensioner Assembly from the engine block. 3. Unscrew and remove Lock Bolt. 4. Remove Pushrod, Ball & Retainer, Spring and “O” ring. Clean parts thoroughly and apply grease to the Balls & Retainer. Re-assembly procedure : 1. Place Spring on Pushrod and compress the spring beyond the hole in the Pushrod. 2. Insert a pin or wire into the hole in the Pushrod to hold the Spring in its’ compressed position. 3. Place Balls & Retainer onto Pushrod. 4. Insert Pushrod into the Tensioner body with the small flat on the Pushrod facing, and aligned with, the Locking Bolt hole. 5. Insert the Locking Bolt and tighten it against the small flat on the Pushrod to lock the Pushrod in the compressed position. Remove the pin that’s holding the Spring compressed. 6. Install the Tensioner assembly onto the cylinder block and install and tighten both Flanged Bolts. Be sure that the “O” ring has been installed at the base of the flange. 7.Looosen the Lock Bolt to release the Pushrod, then re-tighten the lock bolt

Incoming search terms:

YAMAHA RAPTOR 350 Removing stock carburetor and cables

0

Filed Under (Yamaha) by admin on 18-01-2012

download
remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Stuff a clean, dry rag into manifold to keep debris out of motor. 4. Remove stock air box. 5. Remove choke cable from handlebars. 6. Remove carb vent line from bike. Carburetor installation 1. Carefully trim the rubber alignment tab off of the face of the manifold with a razor blade or side cutters. 2. Remove the hex pipe plug from the carb cap using a 11mm or 7/16 wrench. Do not discard plug, as it will be needed later. Install the metering adjustment tool included in the hardware kit. Do not over-tighten as damage may occur to cap. 3. Attach fuel line to carburetor and secure with clamp. 4. Install remote idle cable into tab on top of carburetor. See main manual for this step. NOTE: Nut must be removed from cable before installation 5. Place carburetor into manifold

Incoming search terms:

1996-2004 HONDA XR250R Removing stock carburetor and cables

0

Filed Under (Honda) by admin on 26-11-2011

download
Install the throttle cables into the supplied throttle housing and place onto clean handlebar end. 2. Remove the rubber carburetor alignment tabs from the manifold using a razor blade or sharp cutters. This should be done with the rag left in the manifold. Be very careful not to damage the manifold or your hands while doing this!! 3. Remove the hex pipe plug from the carb cap using a 11mm or 7/16 wrench. Do not discard plug, as it will be needed later. Install the metering
adjustment tool included in the hardware kit. Do not over-tighten as damage may occur to cap. 4. Install provided fuel line onto fuel inlet banjo and secure with pinch clamp. 5. Place Edelbrock carburetor into manifold. Do not tighten clamp yet. 6. Remove the cable bracket end from cable bracket using #2 phillips. 7. Install pull cable (see Figure 2) end into
the 4:00 position of the cable wheel and the return cable into the 1:00 position. Secure cables into cable bracket by replacing end piece and phillips screw. See figure 3.

Incoming search terms:

HONDA TRX 400EX Removing Stock Carb and Cables INSTRUCTION

0

Filed Under (Honda) by admin on 21-12-2011

download
Remove seat/fender assembly and fuel tank. 2. Remove throttle cables paying close attention to routing. 3. Remove thumb throttle housing if you are installing a twist throttle. 4. Remove air box and air box intake tube. 5. Remove stock carburetor. 6. Stuff a clean rag into intake manifold to keep debris from entering engine. Preparing machine for carburetor installation 1 . Route the provided throttle cables per manufacturer’s recommended procedure, routing them the same as the stock cables. 2 . Remove the rubber alignment tabs from the manifold using a razor blade or cutters. Be very careful not to damage the intake manifold! 3. Remove air box intake tube from the air box and use a hacksaw to cut approx. 1½” off of the air box intake tube. Your tube should resemble the one shown in Figure 1. Re-assemble the air intake tube into air box and install back onto bike. Don’t forget to tighten clamp around intake tube and reinsert crank vent into the air boot. Figure 1. Thumb Throttle Attach cable into cable wheel with the cable end at the 8: 00 position of the cable wheel, then into bracket. Secure by replacing the cable bracket end and phillips screw. See Figure 2. Figure 2. Twist Throttle 1. Install the pull (see figure 4 for cable identification) , cable end into the 8: 00 position and the idle cable end into the 11: 00 position on the cable wheel. See Figure 3

YAMAHA YFM 350 Removing stock carburetor and cables.

0

Filed Under (Yamaha) by admin on 19-01-2012

download
Remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Preparing motor for carburetor install 1. Remove stock manifold from cylinder head. 2. Place supplied o’ring into aluminum flange as pictured in figure 1. Figure 1. 3. Install aluminum and rubber flange to motor using supplied bolts. See Figure 2. The shorter 25mm bolt will need to be placed in the bottom hole. IMPORTANT NOTE: Install the aluminum flange with the o’ring towards the motor and the thick side up.

Incoming search terms:

Harley Davidson Softail Drive Side Brake System Installation Manual

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
Removing The Stock Components Although the PM Drive Side Brake System can be installed with the swing arm bolted to the frame, we recommend removing it for better access as well as repainting. Begin by removing rear wheel,stock brake components and belt guard from swing arm. Photo #1 Using supplied 3/4 x 2″bolt,position Drive Side BrakeAssembly on swing arm. Slide assembly to center position of tab and axle spans. Making sure brake mounting tabs are flush with swing arm,snug 3/4 x 2″ bolt to hold assembly and mark swing arm area to be ground Photo #2 . Remove entire assembly from swing arm and thoroughly grind paint away from marked areas Photo #3 . Photo #4 Re-mount assembly to swing arm and slide to rear-most position of both axle and brake mounting tabs. Confirm that brake tabs are flush with swing arm and parallel to each other. Snug 3/4 x 2″bolt and 5/16″socket head cap screws in tabs to hold assembly during welding process. Warning Center the motorcycle on the lift so that it will not fall while you are working on it. Photo #6 Photo #5 Photo #7 Photo #9 Welding Tabs to Swing Arm Note PM recommends all welding be done by a certified welder. Photo #5 Tack weld rear of tabs to swing arm. Avoid excessive welding near brake as- sembly as heat can mar finish. Loosen socket head cap screws and 3/4″bolt,Slide entire assembly to forward most position and re tighten bolts Photo #6 (movement should require minimal effort if tabs are aligned properly) and tack front of tabs to swing arm. Remove brake assembly from swing arm. Weld tabs to swing arm.Verify alignment of tabs, as they must remain parallel to each other. Repaint swing arm and re-install on bike to factory torque specs. Installing Brake Assembly Remove primary bracket from tower assembly (this allows bracket to be installed without having to line up caliper on disc) by removing the three 5/16″socket head cap screws (commonly called allen bolts). Photo #7 Mount rear tire and bolt pulley to rear wheel. Place disassembled bracket against pulley using smaller of two supplied spacers between bracket and pulley. Slide wheel/brake assembly into swing arm. Place large spacer on right side and slide axle in. Do not tighten axle at this point . Photo #8 Slide caliper/tower assembly over disc and install 5/16″x 1″socket head cap screw in center hole to position assembly Photo #9 . Snug, but do not tighten bolt at this point.

Incoming search terms:

Kawasaki ZX-10 R MXL Strada / Pista Plug and Play kit Isntallation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
INSTALLATION STEP # 1 – Removing front transparent fairing and mirrors. The first installation step consists in removing the bike front transparent fairing and the lateral mirrors. The front transparent fairing is fixed to the bike chassis through 6 screws circled in Figure 1 . Please unscrew them and remove the front transparent fairing. Figure 1 : front transparent fairing – screws location It is now necessary to remove both lateral mirrors. First of all, please remove the two internal screws (one of them is circled in Figure 2 while the other is nearby) and remove the lateral mirror. Please repeat this operation for both mirrors. NSTALLATION STEP # 2 – Removing the stock dash. The second installation step consists in removing the stock dash. To do so you need to slacken the lateral fairing. Once removed the lateral mirrors, please remove the central external screw you see circled in Figure 3 . Please repeat this operation for both lateral mirrors. Figure 3: central external screw. Now please slacken the lateral fairings and remove the screw circled in Figure 4 . Please repeat this operation on both sides of the bike. Figure 4: Location of the little internal fairing screws The stock dash is fixed to the bike through three screws that fix the dash to an internal chassis. To remove the stock dash you need to unthread both dash and internal chassis. To do so, please remove the three screws circled in Figure 5 . It is now possible to unthread the chassis and the stock dash