replace timing chain on 2016kx450motor cycle

You search Auto repair manual PDF replace timing chain on 2016kx450motor cycle, if there are search results will appear below. If search results do not exist, please search by others keyword.



  replace timing chain on 2016kx450motor cycle Direct Download speed 5282 Kb/s

  replace timing chain on 2016kx450motor cycle Full Version speed 6162 Kb/s



Lilac LS-18 Motorcycle Maintenance Standards

0

Filed Under (Lilac) by admin on 25-11-2010

download
CYLINDER AND CYLINDER HEAD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Cylinder Bore 54 -0.01 54.1 Boring After boring honing should be performed Ovality 0.01 0.05 Boring After boring honing should be performed Taper 0.01 0.05 Boring After boring honing should be performed Oversize 0.25 steps 55 max. Do R and L cylinders at same time / 4 steps Valve Seat Width 0.8 – 1.0 1.3 Adjust Use a cutter Angle 45∞ Combustion Chamber Volume 18.2cc -0.5cc Remove carbon if heavy accumulation Compression Ratio 7.8:1 Head Gasket Thickness 1.0 Cylinder Head Nut Torque 3.0 kg/m (22 ft.-lb.) Out standard Adjust 8mm nut Intake and Exhaust Ports Port Wall SurfaceMust be smooth Remove carbon Intake and Exh. Valve GuidesOD 12 +0.09 +0.1 ID 7 +0.01 -0.0 7.06 Exchange Intake Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Exhaust Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Intake and Exhaust Valve Seat Face Width Range 0.8~1.0 1.3 Use valve seat cutter Intake Valve Guide Clearance 0.02~0.04 0.08 Replace valve or guide Exhaust Valve Guide Clearance 0.06~0.08 0.12 Replace valve or guide Valve Spring (Large) Installed Load 10.2 kg 8.7 kg Replace Fitted length 31.5 Free Length 36.5 34.7 Replace Tilt 1.5/100 3/100 Replace Valve Spring (Small) Installed Load 5.48 kg 4.65 kg Replace Fitted length 29.5 Page 4 of 10 Free Length 33.5 31.8 Replace Tilt 1.5/100 3/100 Replace Rocker Arm ID 12 +0.00 +0.02112.07 Replace Rocker Shaft OD 12 -0.06 -0.024 11.92 Replace Arm and Shaft Clearance 0.045~0.006 0.10 Replace arm or shaft Tappet Clearance 0.05 Out standard Adjust Measure cold at TDC Rocker Arm Ball Surface 1.8îR -0.006 -0.024 Replace if severe wear Pushrod Bend 0.1 0.5 Straighten Over 100mm (2) CRANKSHAFT, PISTON AND CONROD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Piston OD @ Top 53.65 -0.02 Max Diameter 53.95 -0.015 53.85 Replace Ovality 0.1 Piston and Cylinder Clearance 0.04~0.05 0.15 Replace Piston Ring Groove Clearance 0.03~0.07 0.10 Replace Piston Oversize Step 0.25 4 steps Top Ring and 2nd Ring Thickness 2 -0.01 -0.03 1.92 Replace Width 2.5 -0.01 0.55kg Tension 0.85 – 1.15kg 1 Replace End Gap 0.15 – 0.35 Replace Oil Ring Thickness 3.2 -0.01 -0.03 3.12 Replace Width 2.5 -0.1 Tension 1.0~1.3kg 0.65kg Replace End Gap 0.15~0.35 1 Replace Ring Gap Position 120∞ 3 equal spacesOut standard Adjust Avoid Piston Pin Axis Ring Oversizes 0.25 steps 4 steps Piston Pin OD 15 -0.0 +0.006 14.95 Replace Pin Hole in Piston ID 15 +0.012 -0.015.05 Replace Pin and Piston Clearance -0.006 ~ +0.012 0.06 Replace Hand push fit piston at 100∞C Conrod Small End Bush ID 15+0.027+0.016 15.07 Replace bush Conrod and Piston Pin Clearance 0.01~0.027 0.07 Replace Crankpin OD 24.94 +0.0+0.0124.90 Replace Crankpin Roller OD 5 (+0.001+0.003) Refer to conrod ID Replace 3Sizes; 52 per assembly for selective fit 5 (+0.0 -0.002) 5 (-0.003 -0.005) Conrod ID 34.95+0.03+0.02435.02 Axial Play 0.2~0.4 0.5 Adjust Radial Play 0.026~0.036 0.06 Replace

Incoming search terms:

MOTORCYCLE ROLLER CHAIN Maintenance and Lubrication

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
Cleaning and Relubrication Perhaps the largest contributor to shortened chain life is inadequate lubrica- tion. All working parts of a chain should be lubricated uniformly. The use of the highest viscosity oil that allows for flow between the link plates and coats pin-bushing areas will normally provide the greatest wear resistance. Apply oil to the upper edges of link plates. This allows for the greatest access of oil to pin-bushing joints. For open drives, excess lubrication on outer chain surfaces should be removed, since it will either be thrown off during operation or serve to collect foreign materials. If foreign objects or surplus lubrication accumulates on chain surfaces to the extent of making re-lubrication of the joints impossible, the chain must be cleaned. Standard roller chains may be cleaned by washing in kerosene or any other good petroleum-based solvent. WARNING: These solvents are flammable. Agitate the chain to assure penetration of the solvent and a thorough flushing of the pin-bushing areas. Drain off excess solvent and inspect bushings and pins for wear. Replace the chain if wear is excessive or parts are fractured or missing. O-ring chains may be cleaned externallyby washing in kerosene. Do not use any other cleaning agent or the O-rings may be damaged. When cleaning O- ring chain, clean only the external areas of the chain. Do not attempt to force kerosene into the pin-bush cavity. Do not try to repair a worn-out chain by replacing individual links. The pitch of the new links will be shorter and will most likely result in chain fatigue failure and/or severe sprocket damage. For chains which are still usable, soak them in SAE 40 or 50 automotive engine oil (without additives). Flexing the chain in oil will assure greater penetration of lubricant. Inspect and clean sprockets. If sprockets are worn or damaged, they should be replaced.Installing new chain on worn out sprockets will significantly shorten the chain’s service life. WARNING: always wear eye protection when assembling or disassembling chain

Incoming search terms:

POLINI X1 GENERAL INFORMATION AND SPECIFICATIONS

0

Filed Under (Polini) by admin on 02-12-2010

download
Air cleaner – Clean and reoil daily or after each moto to prevent motor failure and reduced performance. Transmission oil – change after every race, or at end of riding day. Chain – check tension and lubricate before every ride, adjust or replace as needed. Reoil after riding in damp conditions. Clutch – disassemble and clean clutch assembly frequently, every 2-3 races at least. Inspect kickstarter gears at this time. Ignition cover – remove cover and wipe dry after each ride or after washing bike to remove condensation. Piston rings – replace as often as every 3-5 races with expert rider, less often with less aggressive riders. Piston, pin, rod bearing & circlips – replace as often as every 8-10 races with expert rider, less often with less aggressive riders. Coolant – change yearly, make sure there is at least a 50/50 mixture of antifreeze if freezing temperatures are possible. Steering bearings – Check daily for looseness or play. Adjust and regrease as needed. Swingarm – Check often for looseness. Regrease several times a year. Replace bushings if any play is evident. Sprockets – check for worn or curved teeth each time chain is adjusted. Chain roller& wear pads – check roller for free rotation when checking chain. Make sure roller is not bent or damaged. Check chain wear strips on swingarm and chain guide frequently. Replace as needed to prevent chain from damaging motorcycle. Spokes – Check after each race or after each day of riding for looseness or damage. Wheels & tires – check wheels after each race for dents, cracks or other damage. Check tires for cuts, damage or wear. Check tire pressure daily and adjust for riding conditions. Shock – Check shaft area daily for signs of oil leakage or damage. Check swingarm and shock bushings for looseness. Forks – Check forks daily for leaking oil or damage to tubes. Make sure forks are not twisted check for smooth operation. Spark plug – check sparkplug color and condition after each race or end of riding day. Adjust jetting to keep plug from fouling or overheating. Silencer – If bike seems to be getting louder, replace packing and decarbonize inner tube. Expansion pipe – check daily for large dents, damage or leakage. Remove carbon from headpipe when pipe is removed. Have large dents fixed, or any dents within 8″ of the cylinder. Replace o-rings on pipe as needed to maintain a good seal. Footpegs – check daily for proper operation, pegs should spring back into place. Make sure pegs are not bent or overly dull. Handlebars – check bars after any crash for bending. Look for cracks near bar clamps. Replace bars that have been straightened more than 2 or three times, or if bar is badly bent. Aweakened bar can snap suddenly causing injury to rider. Throttle – check throttle for proper operation each time before bike is started. Remove and clean inside of grip and bar as needed. Grips – check grips daily for wear or looseness. Replace as needed. Use grip glue & safety wire to help hold grips in position. Calipers & pads – check pad wear and caliper function daily or after each race. Replace pads and clean calipers as needed. Brake lever – check lever daily for damage or wear. Make sure lever is at proper angle for both seated and standing positions. Leave lever clamp loose enough to allow clamp to rotate during crash rather than breaking lever. Check and adjust freeplay as needed. Brake pedal – Check pedal daily for damage and proper freeplay. Adjust rear caliper as needed. Reeds – Remove and inspect reed block during every ring change. Check reeds for signs of wear, fraying and cracking. Make sure reeds sit flat and seal well. Replace at any sign of wear or damage or at least once a year, more often for expert riders. Nuts & bolts – Check all nuts and bolts regularly. Make sure to check engine mounting bolts and swingarm bolt frequently

Incoming search terms:

BMW F 650 GS Repair Manual And Maintenance schedule

0

Filed Under (BMW) by admin on 19-11-2010

download
Replace oil in telescopic forks Check the coolant and restore to correct level if necessary *) Replace the coolant (every 2 years) every 2years Check valve clearances, adjust if necessary Replace the spark plug Drain the outlet hose from the air filter box Replace intake air filter If motorcycle is operated in very dirty or dusty conditions, clean or replace the intake air filter every 10,000 km (6,000 miles); check every 3,000 km (1,800 miles) Replace fuel filter (every 20,000 km/12,000 miles) 20,000 km Check clutch play, adjust if necessary Check wheel spoke tension and tighten if necessary more frequently if motorcycle is ridden in severe off-road conditions Examine brake pads and discs for wear, replace if necessary *) more frequently if motorcycle is ridden in severe off-road conditions Check brake fluid level at front and rear and top up if necessary *) Check for operation of brake system and freedom from leaks; repair/replace if necessary *) Replace the brake fluid at least once a year Replace the primary front/rear brake master cylinder cup (every 40,000 km/24,000 miles on a motorcycle with ABS ) 40,000 km Check wheel bearings and replace if necessary *) Check or, if necessary, replace chain, sprocket, chain guide rollers and pinion *) more frequently if motorcycle is ridden in severe off-road conditions Check chain tension and adjust if necessary *) Check battery acid level, add distilled water if necessary more frequently if motorcycle is ridden in severe off-road conditions Clean and grease the battery terminals, if necessary Check steering head bearings and adjust *) or replace if necessary *) Grease the side and main stands Grease the brake pedal Check bolts and nuts on engine mountings, frame connections, exhaust system mountings, swinging fork pivot, suspension levers, brake pedal, main and side stands and quick-release axles for tightness Final inspection with road safety and functional check

Yamaha YZ 250F Camshafts REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 30-12-2011

download
Remove the 4 bolts that hold the exhaust cam cap in place, lift the cam cap off. It may be necessary to pry very lightly on the cap to lift it off its dowel pins. Do not use the cam lobes as the pry point. Be careful not to drop the dowels and also be careful to not lose the half moon shaped retainer for the bearing under the cam cap. Remove the 6 bolts that hold the intake camshaft cap and lift the cam cap off the camshaft, again, be careful to not drop the retainer or dowels. Lift the intake camshaft out of its pocket in the cylinder head casting. Remove the cam chain from the sprocket, set the stock camshaft aside. Lift the exhaust cam out of its pocket in the cylinder head casting and remove the chain from the sprocket. Do not drop the cam chain, dangle it over the side of the engine while keeping slight upward pressure on the chain to maintain its position on the drive sprocket on the crankshaft. Fit the half moon shaped retainers in the grooves of the Hot Cams camshaft bearings to ensure good fit, set retainers aside for the time. Using assembly lube, lube the shim buckets, bearing surfaces for the camshafts in the cylinder head, and pack some in the camshaft bearings. Set the exhaust cam into the cylinder head casting while at the same time fitting the cam chain over the sprocket. Make sure that you keep all the cam chain slack to the back of the engine. The cam chain pulls the camshaft sprockets in a counter clockwise direction and the slack of the chain must be kept on the cam chain tensioner side of the engine. The exhaust cam has two timing marks on it. When correctly installed one mark will be at the 9 o’clock position and the other mark will be at the 12 o’clock position. When correctly timed the mark at 9 o’clock will be aligned with the valve cover gasket surface. Repeat the above process for the intake camshaft. Again, make sure you keep the chain slack to the cam chain tensioner side of the engine. Check to be sure the crankshaft is still at TDC. The intake cam has two timing marks also. One at 12 o’clock and the other at 3 o’clock. When both cams are installed correctly, the valve cover gasket surface will form a straight line through the exhaust timing mark at 9 o’clock and the intake timing mark at 3 o’clock

Incoming search terms:

Harley-Davidson CHAIN DRIVE INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 15-04-2012

download
1) Assemble & install the chain tensioner assembly over the primary chain as shown in figure 1. 2) Install the compensator sprocket with extender & spacer (numbers 5, 6, & 7, FIG 2)(#7 is not included in this kit), primary chain, chain tensioner, and clutch basket simultaneously onto the motor drive shaft & transmission main shaft. Rotate the chain drive slightly as needed to allow the splines to line-up. 3) Install the chain tensioner nut loosely on the chain tensioner bolt. 4) Install the sliding cam onto the compensator sprocket, & slide the compensating sprocket cover-assembly (#3) over the cam. 5) Apply 2 drops of Rivera “Red” thread-lock on the threads of the motor drive shaft, & install the motor nut loosely with the fingers at this time. The hex spacer (#7) and spacer (#2) as seen in fig.2 are not provided in Rivera Engineering’s chain drive kit. These components are required with some applications, and can be purchased from your local Harley-Davidson dealer. FIG 2 6) Apply 2 drops of Rivera “red” thread-lock on the threads of the transmission main-shaft and loosely install the clutch hub nut (left hand threads). 7) Place the HD “Primary Drive Locking Tool” HD-41214 on the primary chain as shown in figure XXX and tighten the motor sprocket nut to 150-165 foot-pounds. 8)Turn the locking tool 180 degrees and move it to the clutch sprocket. Tighten the clutch hub nut to 70-80 foot pounds (left- hand thread). Adjust chain tension so that the top strand has 5/8″- to-7/8″ of up and down play (cold drive train). Tighten the center bolt nut to 21-29 foot pounds of torque.

Incoming search terms:

PRO-CYCLE AND PRO-CYCLE XLT 1,000-Lbs. Capacity Motorcycle Lift

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
1. Always inspect the lift for freight damage and make note of any damage on the bill of lading. 2. In case of freight damage, call the truck line immediately and report the damage as a freight claim. Final Set-Up for model Pro-Cycle This lift is more than 90% factory pre-assembled. The following steps will guide you through the final set-up. IT WOULD BE EASIER FOR TWO MEN TO COMPLETE FOLLOWING STEPS. 1. Unpack the lift from the shipping skid. With the lift table up side down, connect the air hose to the air cylinder (Part # 26). 2. After tightening the hose to the cylinder, flip the lift over with the table surface up. 5 3. Lift up the table manually to the first lock position to make sure the lift is rising freely. Lubricateing the joints again before use will ensure a better performance of the lift. 4. Connect the other end of the air hose to the foot-operated valve. Then connect the foot- operated valve to 100 PSI air supply. DO NOT USE AIR SUPPLY WITH PRESSURE MORE THAN 100 PSI. 5. Release the safety bar by pushing the handle down. Operate the foot valve by stepping on the footpad forward to raise the lift. The safety bar should engage the ladder automatically while lift is rising. Step on the footpad again to set the pad in middle position to stop the lift when it reaches the desired height. ALWAYS LOWER LIFT IN THE NEAREST LOCKED POSITION BEFORE BEGINNING WORK. NEVER USE THE LIFT UNLESS YOU ARE IN A LOCKED POSITION. The lift should never be left unattended while attached to air pressure. Disconnect the air pressure when lift is not attended by qualified persons. 6. Install the vise using bolts and nuts supplied with the lift (part # 6 to 12). See fig #1. 7. Install the approach ramp by dropping it into the holes punched on the rear edge of the table. The final Set-Up for the Pro-Cycle model is complete

Incoming search terms:

CL-1000 CONDOR CYCLE LOADER USER INSTRUCTION MANUAL

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
Confirm that the cradle is set in the optimized position setting (See RECOMMENDED CRADLE SETTINGS) for the entering tire and wheel. Adjustment of cradle is crucial for optimum retention. Optimum retention is achieved by trying different settings. ( REFER TO CAUTION PARAGRAPH BELOW ): If the optimum vertical support is achieved, the motorcycle will hold itself upright. If optimum retention is not achieved try different cradle settings. ( REFER TO CAUTION PARAGRAPH BELOW ). Once cradle is positioned, tighten the brakes using the eye bolts and place the Cycle Loader in front of the motorcycle. Push or drive the motorcycle, centered into unit, until the cradle of the Cycle Loader has fully engaged the wheel. Once the wheel is cradled, proceed to push further into the Cycle Loader until the wheel has engaged the front stop. If the optimum vertical support is achieved, the motorcycle will hold itself upright. As an extra precaution, an optional Velcro strap may be used to strap the cradled wheel to the front stop (Optional Velcro strap purchased separately). Always strap Velcro through the wheel and around the front stop below the upper front stop flange. Loosen the brakes and use two (2) tie-down straps to secure the motorcycle to the two front eyebolts of the Cycle Loader. Hook wench to Ω” ‘U’ hook in front of Cycle Loader. Use the wench to pull the Cycle Loader with motorcycle up the flat bed. Once the motorcycle is all the way on the flat bed, the bike should be secured to the flat bed itself. For more information on use, refer to www.condor- lift.com. RECOMMEDED CRADLE SETTINGS: The Condor® Cycle Loader is designed so that for every tire/wheel size within the ranges specified a minimum of 2 cradle settings is suitable. **The optimum cradle setting for a specific tire would be, the setting that allows the cradle to tilt flush with the unit/ or º” below the opening in the main unit where the cradle sits, without touching.** The 2nd optimum setting would be the setting forward from the optimum setting away from the entry direction. If less retention is desired at any time due to too much retention or sticking, the cradle may be moved away from the entry direction one notch. RACING APPLICATIONS: For bikes with GP or low durometer front tires compounds, use the 5th cradle setting from the entry directions. CAUTION: Always make sure that all fasteners are tight and all pins are in place prior to use. Understand the limitations of this product and do not exceed these limitations. Always make sure that the unit’s cradle settings are optimum for the tire size of the motorcycle before use. For bikes with very low fenders and or cowlings, a custom cradle may be purchased fitted to specific tire sizes, so as not to make contact. For standard sport bike front wheel combinations, the 1, 2, 3, front settings may be suitable. If instructions are not clear, additional information is available at www.condor-lift. com or call 1-800-461-1344. Technical Components Development & Design is not responsible for any damage incurred by exceeding this product’s limitations in structure and/or functionality.

HONDA GL1800 TIMING CHAIN COVER INSPECTION NUT INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 28-02-2011

download
GL1800 TIMING CHAIN COVER INSPECTION NUT 1. Place bike on center stand. 2. Remove the inspection nut on the bike using a 17mm socket. 3. Remove the rubber o-ring seal from the inspection nut and place on new inspection nut. 4. Install the new inspection nut using the 17mm socket.

ULTIMA IGNITION MODULE AND KIT INSTALLATION MANUAL FOR HARLEY DAVIDSON

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
Disconnect battery. 2. Mark location of timing plate in relation to inside of cam cover. This will give a starting point for timing on new module. Remove old ignition if applicable (see manual) Clymer, Haynes. 3. If your bike is not equipped with timing rotor M/W# 53-528 OEM#32402-83 you must buy one (included in kit). Also a single fire coil is needed (included in kit) M/W# 53-632. Any single fire coil rated 2-4 ohms can be used. NO SOLID CORE PLUG WIRES (copper, silver) they will damage the unit. 4. Install module: helpful hints, early model nose cones, i.e. Shovel Heads, the hole for the wire may need to be drilled out. Align with previously scripted mark for timing. Use lockwashers for stand offs for correct clearance of cover plate. Run wire loom. 5. Connect wires, see wiring diagram. Tape unused wires, green or brown. 12v to tach (brown) will damage module. Set timing. 1996 and later should not be timed 20˚ BTDC as the OEM module, but at 35˚ BTDC. Use this mark when using timing light. If VOESswitch is not used you must ground VOES wire (green) while timing. Refer to manual for correct identification of timing marks. At start up and timing, set spark advance in middle position. FUNCTION SWITCHES LED timing indicator light: When out, shows TDC. When ignition is on, LED will light up. When engine is cranking LED will blink. Electric Start/Kickstart: Set accordingly. VOES/Race mode: VOES switch lets the motor run smoother and improves gas mileage. If you don’t use it or add one tape up green wire and switch to race. VOES switch to use, M/W# 53-652. Spark advance: High compression motors should use race mode and 93 octane or better gas. Changing from VOES to race changes advance curves. Agood rule of thumb is if the engine knocks when throttle is applied in high gear, turn back spark advance curve until it stops engine knock. RPMlimiter: Set at desired RPM to cut engine power. Rear Cylinder: This is for racing and should be set at a dyno. +/-5˚. Rear cylinder timing is achieved through this adjuster. Most should dial to middle setting and leave alone. After all switches are set, install cover with supplied gasket and feel the increased performance of a solid state single fire ignition. Again, we remind you, if you don’t feel confident about installing this unit, let a qualified mechanic do it and be assured you are getting the best performance and gas mileage possible.

Incoming search terms:

Incoming search terms: