replacing a choke cable on 1999 dyna super glide

You search Auto repair manual PDF replacing a choke cable on 1999 dyna super glide, if there are search results will appear below. If search results do not exist, please search by others keyword.



  replacing a choke cable on 1999 dyna super glide Direct Download speed 5282 Kb/s

  replacing a choke cable on 1999 dyna super glide Full Version speed 6162 Kb/s



HARLEY DAVIDSON STAINLESS STEEL BRAIDED CLUTCH CABLE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
REMOVE CLUTCH CABLE 1. See Figure 1. Loosen clutch adjuster to obtain slack in the clutch cable (2) by performing the following: a. Locate cable adjuster (1) and slide off rubber boot (4). b. While holding cable adjuster with 1/2-inch wrench, loosen jam nut (3) using a 9/16-inch wrench. c. Turn cable adjuster until there is a large amount of free play at hand lever. 1 2 3 4 is 00889 1. Cable adjuster (1/2-inch) 2. Cable end 3. Jam nut (9/16-inch) 4. Rubber boot Figure 1. Clutch Cable Adjuster 2. See Figure 2. Remove the retaining ring (1), pivot pin (2) and clutch cable anchor pin (3) from the hand lever. 2 3 1 is 00891 1. Retaining ring 2. Pivot pin 3. Clutch cable anchor pin Figure 2. Clutch Cable Compoments 3. See Figure 3. Drain transmission lubricant and remove fill plug dipstick. Remove the six screws that hold the clutch release cover in place. Remove the clutch release cover, being careful not to damage the gasket. NOTE The clutch release cover gasket (P/N 36801-87B) will need to be replaced if torn or damaged to prevent transmission fluid from leaking from the release cover. 4 3 5 2 6 1 is 00894 Figure 3. Clutch Release Cover Screw Sequence 4. See Figure 4. Note position of retaining ring opening. Retaining ring opening must be positioned in approximately the same location during reassembly. Remove retaining ring (1). 5 4 1 3 2 is 00895 1. Retaining ring 2. Inner ramp 3. Cable fitting 4. Clutch cable 5. Ramp coupling Figure 4. Clutch Cable Connection 5. Pull inner ramp (2) and coupling (5) out of side cover. Hold inner and outer ramps together to keep balls from falling free. 6. Rotate the inner ramp to a position that will allow the coupling (5) to be disconnected from the inner ramp lever arm. Disconnect coupling from inner ramp. Disconnect cable end from coupling. 7. Back out threaded cable fitting from side cover. Ensure that o-ring is removed with cable. Discard o-ring. INSTALL CLUTCH CABLE 1. See Figure 4. Obtain braided stainless steel clutch cable from kit. Apply a light coat of oil on new o-ring and install o-ring (Part Number 11179) onto threaded portion of clutch cable (4). Insert clutch cable fitting (3) into clutch release cover. Do not tighten cable fitting at this time. 2. Connect cable end to coupling. Rotate ramps for best access and install coupling on inner ramp. Place ramp assembly in position in side cover. 3. Install retaining ring. Position retaining ring opening so it is located approximately over the outer ramp tang (the stop that prevents rotation). NOTE Replace clutch release cover gasket if torn or damaged. 4. See Figure 3. Place gasket, if removed, on side cover and install side cover. Tighten the six screws in the order shown to 84-108 in-lbs (10-12 Nm) . 5. Tighten the clutch cable fitting to 36-60 in-lbs (4-7 Nm) . 6. Place a few drops of oil inside cable housing. 7. Route clutch cable as follows: SOFTAIL MODELS FXSTD, FLSTS, FXSTS and FXST – Route clutch cable from the clutch release cover, across the frame, up along the front frame downtubes and across the front of the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. FLSTF and FLSTC – Route clutch cable from the clutch release cover, across the frame and up along the front frame down- tubes, up to and behind the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. DYNA MODELS FXDWG – Route clutch cable from the clutch release cover, under frame and across to the left side. See Figure 5. Insert cable (1) into clip (2) at the bottom left side of the frame

Incoming search terms:

HARLEY DAVIDSON DIAMONDBACK "LE" CHROME SERIES CLUTCH CABLE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
CLUTCH CABLE REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery or main fuse following the instructions in the appropriate Service manual. 2. When performing cable disassembly procedures, make careful notes as to the existing cable routing and existing cable strap locations. New straps can be installed in the same locations. 3. Remove the clutch cable following the instructions in the appropriate Service Manual. 4. If installing different handlebars, install them now (refer to the appropriate handlebar instruction sheet) and measure the change in distance that will be required from the end of the cable housing to the clutch lever. Install proper length clutch cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00448b) 5. Compare the additional required length to the cable provided in your kit. If the cable is more than two inches (50.8 mm) longer or more than one inch (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. CLUTCH CABLE INSTALLATION Sportster and Softail Models Do not over-tighten clutch cable threaded end fitting. Use recommended torque values. Damage to threaded fitting can lead to loss of transmission fluid, which could result in loss of control and death or serious injury. (00449c) -J04568
NOTE Damage to the clutch cable threaded end fitting due to improper handling/installation is not covered under the Harley-Davidson Motor Company Warranty. 1. See Figure 11. Apply a light coat of clean engine oil on the new O-ring (2) before installing the O-ring onto the threaded portion of the clutch cable end. 2. Install the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). 3. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet. FLTR Models with Fairing Lowers 1. See Figure 1. Carefully twist the clutch cable around the coiled opening in the clutch cable guide (2) with the eyelet toward the left handlebar. 2. Route the clutch cable assembly down from the clutch cable clamp while crossing to the right side of the vehicle. Run the cable between the inboard side of the right frame downtube and the outboard side of the voltage regulator. 3. The clutch cable clamp, mounted on the engine guard, has two fingers, an upper and a lower. Feed the cable assembly under one finger and over the other. 4. Finish the installation of the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). NOTE See Figure 2. Adjust the clutch cable clamp to 2.25 ± 0.25 in. (57.15 ± 6.35 mm) as measured from the inside lower left fairing mount to the clutch cable clamp. 5. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet.

Incoming search terms:

Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

Incoming search terms:

Harley-Davidson S&S Super E and G Series Shorty Carburetors Installation and Jetting Instructions

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
throttle linkage with no cable modification. S&S Super E and G carb kits for 1936 to 1989 Big Twins contain a throttle cable guide (11-2339) designed for butterfly type throttle cables, and kits for 1990 and later Big Twins contain a taller throttle cable guide (11-2338) designed for CV type throttle cables. See Picture 2. The two throttle cable guides are interchangeable on the carburetor body, and can be changed very easily to update older carburetors or to accommodate custom throttle cables which are not stock for a particular year chassis. 1981 to Present Sportster Models Stock Sportster models from 1981 to 1987 have two cable throttle system designed for butterfly type carburetors. Sportsters from 1988 to present have a two cable throttle system designed for use with the stock constant velocity (CV) type carburetor. Since the taller #11-2338 cable guide bracket can not be used on a Sportster chassis due to insufficient frame clearance, throttle cables on Sportsters originally equipped with a CV type carburetor must be changed to butterfly style cables. S&S can supply the correct style throttle cables. See S&S Throttle Cable Application Chart. Picture 2 S&S THROTTLE CABLE APPLICATION CHART Length Total Housing Length Vinyl Housing Part Number Open Side Part Number Close Side Fitment 36″ 32″ #19-0430 #19-0431 For Buell with 7/8″ handlebars 36″ 32″ #19-0432 #19-0433 To ’95 ’81-’85 FX and FL; All ’81-’85 XL (Also pre-’81 w/2-cable throttle housing replaced.) For Buell with 1″ diameter handlebar 36″ 32″ #19-0436 #19-0437 ’96-Up 883-1200 XL 39″ 35″ #19-0434 #19-0435 To ’95 Softail (FXSTC, FXST, FLSTC, FLSTF) ’86-’94 FXR, ’93-’95 Dyna 39″ 35″ #19-0438 #19-0439 ’96-Up Softail (FXSTS, FXSTC, FLSTC, FLSTF) ’96-Up Dyna 42″ 38″ #19-0446 #19-0447 To ’95 custom application 42″ 38″ #19-0440 #19-0441 ’96-Up custom application 48″ 44″ #19-0462 #19-0463 To ’95 All FLT Models 48″ 44″ #19-0464 #19-0465 ’96-Up All FLT Models ” 1996 to Present Buells 1996 and 1997 Buells require special S&S butterfly style throttle cables for Buells, which are compatible with the stock 1996-1997 throttle assembly. 1998 and later carburated Buells require installation of stock 1996 – 97 throttle grip and the special S&S Buell style throttle cables when installing Super E or G carburetors. S&S Throttle Kits S&S throttle kits fit 1″ handlebars and can be used on most chassis. (An adapter sleeve is available for use with earlier, 7 ⁄ 8 ” OEM handlebars originally equipped with internal throttle cable.) Barrel fittings on S&S cables readily “plug in” to S&S Super E, G, and stock H-D 1981-’90 butterfly type carb throttle linkage. Kits include one opening and one closing side cable, left and right grips, and handlebar clamps. Kits with 36″, 39″, 42″, or 48″ length cables are available. Length specified refers to overall cable length. Vinyl covered outer housing is 4″ shorter than overall length

Incoming search terms:

HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

Incoming search terms:

HARLEY DAVIDSON FXD (Dyna Super Glide) TACHOMETER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
1995 Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1.1995 MODELS, REMOVAL OF ELECTRONIC SPEEDOMETER AND BRACKET 1a. Refer to applicable Service Manual procedure and remove seat. 1b. Refer to applicable Service Manual procedure and remove fuel tank. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) 1c. Remove speedometer sensor cable from mounting clips under tank. See Figure 1. The 3-place speedometer sensor connector [65] is located on the frame beneath the seat. Remove connector from t-stud and disconnect. Cut cable tie holding sensor wires to right rear frame tube. 1d. Refer to applicable Service Manual procedure and remove headlamp, for work clearance. 1e Remove handlebar clamp screws securing speedometer bracket. Remove speedometer, bracket, and harness. 2.1995 MODELS, DISCONNECT MAIN WIRING HARNESS 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 2a. Disconnect the battery, negative cable first. Refer to applicable Service Manual procedure and disconnect main wiring harness 8-place connector [21A, B], at the front of the motorcycle. 3.1995 MODELS, REMOVE SPEEDOMETER LEADS FROM 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 3a. See Figure 2 and Service Manual wiring schematic. Pull the following wires and terminals out of connector [21B]. Wire Color Cavity Number Orange/white 5 White/green 1 Black 2 3b. Remove the large female connector from the fuel gauge black wire. 3c. Slide the wires removed in step 2a out of the plastic conduit covering the wires connected to the 8-place connector. 1 WARNING 1 WARNING 1 WARNING Figure 1. Speedometer Sensor Connection [65] 4973 Speedometer sensor connector [65] Figure 2. Tachometer/Speedometer Wire Splices and Terminal Connections [21B, A] i00240-.tif Splices 4.1995 MODELS, REMOVE INDICATOR LAMPS FROM BRACKET 4a. Remove the screws that secure the indicator lamps assembly to the speedometer bracket. Retain screws and indicator lamps assembly for installation on speedometer/tachometer bracket later. 5.1995 MODELS, REMOVE SPEEDOMETER FROM BRACKET 5a. Unscrew boot from speedometer reset switch. Remove cover screws and rear cover. 5b. See Figure 3. Note position of rear speedometer gasket and remove it. Push on rear of speedometer while simultaneously pulling speedometer and front gasket from bracket. Do not remove front gasket from the speedometer. 6.1995 MODELS, INSTALL SPEEDOMETER IN KIT BRACKET 6a. See Figure 5. Place wires from speedometer through front of left opening in double bracket. Lubricate the front and rear gaskets with isopropyl alcohol or glass cleaner to ease installation. 6b. Insert speedometer into the front of the double bracket. Be sure wire guides are aligned with opening at bottom of bracket. 6c. Place rear gasket in position and align gasket tabs. Work gasket into space between speedometer and bracket by pushing speedometer against one side of bracket while pushing gasket into position at the opposite side. 6d. Add amber bulb assembly from kit to speedometer in order for tachometer and speedometer backlighting to match. 6e. Replace cover and boot from reset switch.

Incoming search terms:

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/IDLE CABLE KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be installed in the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3 2 1 is00825 1. Brake lever 2.5/32 inch (4 mm) cardboard insert 3. Brake lever bracket Figure 1. Install Cardboard Insert 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 3 4 1 2 5 is 02071 1. Upper switch housing 2. Lower switch housing 3. Throttle cable adjuster 4. Idle cable adjuster 5. Adjuster jam nut Figure 2. Handlebar Throttle Control 4. Remove the right upper and lower switch housing screws. 5. Loosen the upper screw securing the handlebar clamp to the master cylinder housing. Remove the lower clamp screw and flat washer. NOTE If possible, leave the friction shoe in place. The friction shoe is a loose-fit and may fall out or become dislodged if the lower switch housing is turned upside down or shaken. 6. See Figure 3. Remove the brass ferrules from the notches on the inboard side of the throttle control grip. Remove the ferrules from the cable end fittings. 1 2 4 3 is 02072 1. Throttle cable 2. Idle cable 3. Brass ferrule 4. Notch Figure 3. Throttle/Idle Control Cables 7. Pull the crimped inserts at the end of the throttle and idle control cable housings from the lower switch housing. For best results, use a rocking motion while pulling. Remove cables with retaining rings from switch housing. Apply a drop of light oil on the retaining ring, if necessary, to help in removal. NOTE If installing different handlebars, measure the change in distance that will be required from the end of the cable housing to the throttle grip. Compare this additional required length to the cables provided in the kit. If the cables are more than 2.0 inches (51 mm) longer or more than 1.0 inch (25 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. Install proper length throttle cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00396b) 8. Follow instructions in the applicable service manual and remove air cleaner and backplate.

Incoming search terms:

HARLEY DAVIDSON CLUTCH CABLE ASSEMBLY INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
36753-87A This kit fits 1987 and later FXLR model motorcycles. 36755-87A This kit fits 1987 and later FXRS/SP model motorcycles. 38601-89 This kit fits 1988 and later FLTC, FLTC-Ultra, FLHS, FLHTC FLHTC-Ultra and FLHTP model motorcycles. 38606-87A This kit fits 1987 and later FXR, FXRS and FXRT model motorcycles. 38607-87A This kit fits 1987 and later FLST, FXST, FXSTC, FXRP, FLTC, FLHT, FLHTP and FLHTC model motorcycles. 38617-95 This kit fits 1995 and later FXSTSB model motorcycles. 38647-98 This kit fits 1998 and 1999 FXSTB model motorcycles. 38661-00 This kit fits2000 and later FXDL, FXDS-CONV and FXDWG model motorcycles. 38664-00 This kit fits2000 and later FXSTD model motorcycles. 38665-00 This kit fits2000 and later FXSTB model motorcycles. 38666-00 This kit fits2000 and later FXSTS, FLSTS, FLSTC, FLSTF, FXDX, FXD and FXST model motorcycles. 38667-00 This kit fits 2000 and later FLTR, FLTRI, FLHT, FLHTC, FLHTCI, FLHTCUI, FLHR, FLHRI, FLHRCI and FLHP model motorcycles. 38672-01 This kit fits 2001 and later FXDWG2 model motorcycles. Kit Contents: QTY DESCRIPTION 1 O-ring, rubber 1 Cable, clutch 1 Pin, cable pivot 1 Grommet (Kit no. 38607-87A, 38660-00A and 38667-00 only) Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson dealer. A SERVICE MANUAL IS NEEDED TO INSTALL THIS KIT. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. 1. Refer to the Service Manual for your motorcycle model. Screw the cable adjuster all the way in to allow for maximum cable free play. 2. Remove clutch hand lever from hand-lever bracket at pivot pin. Remove original clutch cable from hand lever and transmission. Retain anchor pin bushings. 3. See Figure 1. Install lever end of new clutch cable. Position cable eyelet in clutch lever slot. Retain with new cable pivot pin through original bushings. NOTE See Figure 2. When routing cable on models where clutch cable passes through inner fairing (FLHTC, FLHTC-U and FLHTP with fairing), clutch cable eyelet may be too large to pass through clutch cable access hole in fairing. If this is the case, use the template supplied with this sheet to file out a hole to accommodate the new eyelet. Place the grommet included with kit no. 38607-87A, 38660-00A, and 38667-00 in the hole after filing. 4. Secure the clutch lever in the lever bracket with the lever pivot pin and retaining ring. 5. Follow steps outlined in the applicable Service Manual and install the transmission-end of the new cable with O- ring. 6. Adjust clutch cable according to procedure in Service Manual.

Incoming search terms:

HARLEY DAVIDSON TLE/TLE-ULTRA SIDECAR ATTACHMENT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL NOTES Refer to the service manual for more information on these generalized steps. Save all removed parts (unless otherwise noted) for installation of this kit or for motorcycle operation without the sidecar. 1. For TLE-Ultra Models: Remove both lower fairings. 2. Remove the bolt and lockwasher securing the right passenger footrest bracket and remove the bracket with footrest. 3. Remove the three right side exhaust heat shields. Some models may require removal of the right side exhaust pipes. 4. Remove stock clutch cable. 5. Remove rear master cylinder/rear brake pedal assembly. Remove rear brake pedal from master cylinder assembly. Remove and save rubber pedal pad and brake pedal. Discard cotter pin. 6. Cut the cable straps holding front oxygen sensor connector to frame bracket. 7. Remove wire harness/brake line clip from right lower frame tube. INSTALLATION New Clutch Cable Installation 1. Refer to the service manual and follow instructions to remove stock clutch cable. 2. Refer to the service manual and follow instructions to connect the new clutch cable to clutch hand lever. 3. For FLHT/C/CU: Follow the instructions in the service manual to route new clutch cable through fairing. 4. For FLHR/C Models: Capture the cable in a clamp at the left upper passing lamp bolt. On FLTR models, capture the cable in a clamp at the left upper bolt securing the speedometer and tachometer housing to the upper fork bracket. These locations are identical with stock cable routing. 5. See Figure 1. Route clutch cable down along left frame downtube (1). 6. Continue to route cable down between left front engine isolator and crankcase. Clutch cable will cross to the right side of motorcycle beneath the crankcase, to the clutch release cover on the right side of the transmission. 7. Install clutch cable fitting into clutch release cover. Refer to the service manual. NOTES The final positioning and attachment of the clutch cable and clutch cable adjustment will be performed after sidecar mounts have been installed. Verify that the clutch cable and the rear brake line do not make contact. Damage could result. 1 2 3 is05785 1. Downtube 2. Clutch cable 3. Route clutch cable behind left front engine iso- lator Figure 1. Route Clutch Cable Relocating Oil Pressure Sending Unit NOTES Perform this procedure on all models equipped with an oil pressure gauge or Police models. All other models proceed to “Master Cylinder Assembly/Rear Brake Pedal Modification.” 1. Remove cable strap securing oil pressure wire harness to frame. 2. Locate the latch on connector to oil pressure sender (next to lower right frame downtube). Raise latch on connector and disconnect connector from oil pressure sender. 3. Remove the oil pressure sender using a 1-1/16 inch open- end crowfoot wrench. 4. See Figure 16. Coat threads of elbow (44) with Loctite 565 and install into crankcase oil pressure sender threads. 5. See Figure 2. Install elbow (1) until snug so open end is in the five-o’clock position (2). Do not over-tighten or crankcase may be damaged. 6. Coat threads of oil pressure sender with Loctite 565 and install into 90 degree brass elbow. Use a 1-1/16 inch open- end crowfoot and tighten to 96-120 in-lbs (11-14 Nm) . 7. Install connector on oil pressure sender unit. Verify that slight clearance to the right engine isolators is present. Adjust position of elbow as required to provide clearance

Incoming search terms:

Incoming search terms: