replacing star thumb screw on harley

You search Auto repair manual PDF replacing star thumb screw on harley, if there are search results will appear below. If search results do not exist, please search by others keyword.



  replacing star thumb screw on harley Direct Download speed 5282 Kb/s

  replacing star thumb screw on harley Full Version speed 6162 Kb/s



HARLEY DAVIDSON UNIVERSAL VISTA INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-03-2012

download
1. Turn Harley Davidson thumb screw control all the way off. 2. Remove screw (A) from the motorcycle throttle housing. Position the mounting bracket, as shown in drawing. Replace throttle housing screw through the hole in the foot of the mounting bracket and into the throttle housing. Loosely tighten screw. 3. Slide the cruise control’s slip ring assembly over the end of the throttle grip up to the switch housing. NOTE: Metal band on slip ring assembly is next to switch housing not set screws. Insert correct size rubber filler between slip ring assembly and grip with “joint” of filler on bottom side, midway between two set screws. Tighten all set screws into rubber filler until tight or flush. 4. Place thumb lever slot over eye bolt. Depress spring to line up holes, and insert socket head screw. 5. Insert thumb lever screw into the hole in the head of mounting bracket that keep screw parallel to grip. Install the washer then the locknut on the thumb lever screw. Tighten locknut until mounting bracket and thumb lever are snug BUT loose enough to let thumb lever move freely up and down. 6. Secularly tighten the throttle housing screw (A) in step 1. 7. Twist throttle back and forth to insure there is no binding, slip ring is “SQUARE” with switch housing and thumb lever operates smoothly between “ON” and “OFF”. 8. CRUISE CONTROL ADJUSTMENTS – Twist throttle to half position and push thumb lever down to “SET” position. Throttle should hold snugly in this position. Flipping thumb lever to “OFF” position, releases cruise control hold, throttle should return to “OFF” position. Tightening acorn nut (B) will increase cruise control hold. Loosening acorn nut will decrease cruise control hold. Always check to make sure that throttle can be rotated both ways in “SET” position after adjustments.

Incoming search terms:

How To Adjust the Accelerator Pump On the 40mm Mikuni Carburetor

0

Filed Under (Yamaha) by admin on 21-01-2012

download
1) The “blue” colored screw in the image is the duration adjustment screw. Underneath the head of the screw is a lock nut and the bracket arm that the screw is threaded into. To decrease the amount of fuel squirted the adjustment screw is turned “clockwise” or in. To increase the amount of fuel squirted the adjustment screw is turned “counter clockwise” or out. To get the max, amount of decrease remove the screw and take the lock nut off of the screw. Then replace the screw into the cam arm, then replace the lock nut underneath the arm on the screw. this gives you another 3/32″ of an inch in which the screw can be screwed in.
2) Turn the adjustment screw fully clockwise or IN. Start your engine, Blip your throttle open, if the engine stutters, (hesitates), it is not getting enough fuel so turn the screw counter clockwise to increase the amount of fuel squirted from the accelerator pump into the carburetor. Keep blipping the throttle and adjusting the screw till the carburetor starts to cough. Stop here and turn the screw back in till the coughing stops. Tighten down the lock nut. This should give you the best throttle response with the least amount of coughing and backfiring out the carburetor. Timing Adjustment Screw This is the “Green” colored screw just above the Blue duration adjustment screw. The” Mucker” said it best,,,,, This upper screw adjusts the “timing” of the squirt. By altering it’s setting, you can advance or delay the onset of the fuel squirt. But probably, it won’t have to be touched

Incoming search terms:

HARLEY DAVIDSON CHROME SEAT POST REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
REMOVE 2 1 is00000 1. Seat Post 2. Screw Figure 2. Lower Seat Post 1. Refer to Owners Manual to remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery negative cable. 3. On motorcycles equipped with oxygen sensors, disconnect the rear sensor connector. 4. See Figure 2. Remove screw (2) and washer from the lower seat post (1) and discard. -J04294 1 of 2 5. Disconnect spark plug wires and primary wire from ignition coil. 6. See Figure 3. Loosen the bracket screws (1). Remove seat post screw (2) and seat post with ignition coil and cover. 7. See Figure 4. Remove coil cover screw (5) and cover (4) from stock seat post (1). 8. Remove ignition coil screws (3) and coil (2) from seat post. 2 1 is04241 1. Bracket Screws 2. Upper Seat Post Screw Figure 3. Upper Seat Post Fasteners 2 5 1 3 4 is04337 1. Seat Post 2. Ignition Coil 3. Coil Screw 4. Coil Cover 5. Coil Cover Screw Figure 4. Install Ignition Coil to Seat Post INSTALL 1. See Figure 4. Install ignition coil (2) to new seat post using screws (3). Tighten ignition coil screws to 10-15 ft-lbs (13.6-20.3 Nm) . 2. Install coil cover (4) to seat post with screw (5) and tighten to 30-40 in-lbs (3.4-4.5 Nm) . 3. See Figure 1. Place seat post (1) in position and attach lower post with screw (2), washers (3) and dome nut (4). Tighten screw (2) to 10-15 ft-lbs (13.6-20.3 Nm) . 4. See Figure 3. Attach upper seat post with screw (2). Tighten screw (2) to 12-15 ft-lbs (16.2-20.3 Nm) . Tighten bracket screws (1) to 12-15 (16.2-20.3 Nm) . 5. Connect primary wire to ignition coil. 6. Connect spark plug wires to ignition coil. The rear cylinder plug wire attaches to the top coil post. Ensure that spark plug wire boots are fastened securely. 7. Connect rear oxygen sensor connector, if equipped. 8. Reconnect battery negative cable

Incoming search terms:

HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION

0

Filed Under (Harley Davidson) by admin on 25-12-2010

download
1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite┬« 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit. NOTE For models with mid controls, the right-side rider footrest (foot peg) support bracket must be loosened to allow installation of the lower side interface cover. After the cover has been installed, tighten the footrest bracket attaching screws to 25- 35 ft-lbs (34-47 Nm) . 8. Position the cover around the chrome filler neck cover installed in Step 6. Loosely fasten the cover to the threaded hole in the filler neck cover with the screw and washer. 9. Obtain the chrome upper side interface cover (2), three #10-24 socket head screws (8) and three chrome flat washers (9) from the kit

Incoming search terms:

HARLEY DAVIDSON BILLET HEADLAMP WITH SHORT/ TALL MOUNTS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Kit 68593-06 is a 5-3/4 inch headlamp and kit 69851-06 is a 4-1/2 inch headlamp. Both kits will fit the models listed in Table 1. Table 1. Short and Tall Mount Kits Models Kits 1984-1999 FXSTC, 1998- Later FXST/B, and 2000-Later FXSTD; 1994-2005 FXDWG Short Mount Kit 68595-06 1996-Later XL 1200C and 1998-Later XL 883C; All 2006 Dyna Models; 1999-2000 FXR2/3/4 Tall Mount Kit 69611-06 Additional Parts Required This kit also requires the separate purchase of a Short or Tall Mounting Kit 68595-06 or 69611-06 for your model motorcycle, and can be purchased from a Harley-Davidson dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 21, Table 2 and Figure 22, Table 3. REMOVAL Remove Headlamp and Mounting Bracket for Softail Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. 2. Remove fuel tank. Refer to FUEL TANK in Service Manual. 3. Disconnect 4-place headlamp connector [38] from main wire harness. Headlamp connector is located under fuel tank on left side. 8 5 7 5 6 2 1 3 4 is01835 1. Screw 2. Washer 3. Nut 4. Lockwasher 5. Washer (2) 6. Screw 7. Mounting block 8. Headlamp assembly Figure 1. Softail and Dyna Headlamp Assembly with Mount (except FXSTD) NOTE All Softails (except FXSTD) complete steps 4 through 6. For FXSTD models complete steps 7 through 9 4. All Softails (except FXSTD): See Figure 1. Remove screw (1) and washer (2) from stem and bracket. Discard screw but save washer for later use. 5. Remove and discard mounting block (7) and headlamp assembly (8). 6. FXSTD models: See Figure 2. Remove screw (1) and washer (2) from stem and bracket. Save screw and washer for later use. 7. Remove and discard nut (3), washers (4), and screw (5). 8. Remove and discard mounting block (6) and headlamp assembly (7). 7 3 4 2 1 4 6 5 is01838 1. Screw 2. Washer 3. Acorn nut 4. Washer (2) 5. Screw 6. Mounting block 7. Headlamp assembly Figure 2. FXSTD Headlamp Assembly with Mount Remove Headlamp and Mounting Bracket for Dyna Models 1. Remove seat following the instructions in the Service Manual. 2. Disconnect negative (-) battery cable. 3. Remove fuel tank. Refer to FUEL TANK in Service Manual. 2 1 is01750 1. Cable strap 2. Wire harness Figure 3. Dyna Service Loop (2005-Earlier) 4. 2005-Earlier FXDWG: See Figures 3 and 4. Remove plug on right side of top frame tube. At service loop, remove cable clip and push wire harness into top frame tube. Pull connector out from hole on right side of tube. 2006-Later FXD: See Figure 5. Remove cover under top frame tube, then pull connector out from opening under tube. 5. Disconnect 4-place headlamp connector [38] from main wire harness

Incoming search terms:

YAMAHA V-Star 1100 Carburetor Bowl Screw Repair and Removal After Stripping and Pilot Cap Removal

0

Filed Under (Yamaha) by admin on 19-01-2012

download
When I first started working on bike many years ago, I learned the danger of stripping the heads of Philips screws when removing or installing them on motorcycles. I remember the two worst screws were the casing side-cover aluminum screws and carburetor bowl screws. I think I tried every method of screw removal after they were stripped. Vice grips, better tipped screwdriver, hammer, drill, and other tools were used. One way I learned to remove stripped screws is to re-make the Philips head into a flathead screw. Cutting a slot in the top of the screw and then use a flat-head screwdriver to remove the screw. On some parts this technique can work, other parts and screws it may not. The Philips screws on the bottom of the V-Star carburetor bowls are VERY prone to stripping. In fact, I will not start a carburetor cleaning without new hex head screws to replace the original Philips bowl screws. Replace the bowl screws for yourself if you keep the bike, or for the next rider that will appreciate the hex-head screws when they clean the carburetors. Not many other parts on a V-Star have screws that are prone to stripping. This documentation is to help riders with motorcycle maintenance. Some riders will find themselves with the problem of removing stripped screws. A carburetor cleaning can quickly double in time when you realize the hardest part of the job is removing bowl screws after they strip. And then realizing you do not have the replacement hex-head screws available and must now go to the hardware store.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL TRANSMISSION TOP-COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION – TOP COVER 1. See Figure 3. Remove and retain the stock screw (J) from the top of the transmission upper cover (I). 2. Ease the left side of the cover through the right side of the engine. You may need to angle the transmission cover slightly as you work it into position. 3. Fasten the weld-nut end of the top-cover bracket (2) to the top cover (4) using the screw (3) from the kit. Torque the screw to 6.6 – 9 ft-lbs (8.9 – 12.2 Nm). 4. Fasten the top of the top-cover bracket (2) to the left side of the transmission upper cover using the screw (J) removed in step 1. Torque the screw to 8 – 10 ft-lbs (10.8 – 13.5 Nm). 5. Install the Softail transmission-interface cover (D). Go to the next section in this instruction sheet. NOTE Save the washer (1) from this kit for transmission-interface cover installation. INSTALLATION – INTERFACE COVER 1. See Figure 1. Remove the screw (1) from interface cover at location 1. Keep the screw for installation. 2. Loosen the screw (2) at location 2 approximately three turns. 3. See Figure 2. Position the slotted hole (1) on the interface- cover mounting bracket (2) behind the washer at location 2. 4. Install the screw (4) from Step 1 through the mounting hole on the bracket and into location 1. Tighten the screw to 7 – 9 ft-lbs (9.5 – 12 Nm). 5. Tighten the screw (3) in location 2 to 13-16 ft-lbs (17.6 – 21.7 Nm). 6. See Figure 3. Place the interface cover (D) in position on the motorcycle. Spread the oil-line grommet (E) to wrap around the oil lines, then re-position the grommet in the interface cover. The edge of the interface cover must overlap the top of the top cover

Incoming search terms:

HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION INSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite┬« 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit

Incoming search terms:

HARLEY DAVIDSON MID-FRAME AIR DEFLECTORS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION Model Years 2001-2007 1. Refer to Owner’s Manual and remove seat. 2. Remove stock plastic cruise control cable clip from frame near end of fuel tank if equipped. 2 1 is04321a 1. Mounting Strap Assembly 2. Speed Nuts Figure 1. Install Speed Nuts to Mounting Strap 1 is04324a 1. Mounting Strap Assembly Figure 2. Mounting Strap Location – View of Frame from Above with Seat Removed 1 3 2 4 5 6 is04546a 1.3/4 in. long button head screw and 1 in. OD flat washer 2.7/8 in. long button head screw, P-clamp and 1 in. OD flat washer 3. Well nut, 3/4 in. long button head screw and 3/4 in. OD flat washer 4. U-clip 5. Right side deflector 6. Left side deflector Figure 3. Fastener Locations – View of Frame Rearward of Rear Cylinder, Engine Removed for Clarity 3. See Figure 1. Assemble speed nuts (2) to both ends of mounting strap (1) and align edges of nuts to angled ends of strap. -J04399 4. See Figure 2. Install mounting strap assembly (1) through window of frame. Position strap so speed nuts are aligned over the 1/4 inch diameter holes in frame as shown. 5. See Figure 3. Attach strap assembly to frame using a 3/4 inch length button head screw (1) and the 7/8 inch length button head screw (2) by inserting them from the underside of frame plate. Tighten screws enough to keep strap from moving and prevent it from shifting position during deflector installation. 6. Insert well nut (3) into underside of frame plate. Apply liquid soap to the outer surface of the well nut to ease installation. 7. Remove 3/4 inch screw (1), then position right side deflector as shown and secure with the 3/4 inch screw and 1 inch washer. Do not tighten. 8. Install screw and small washer (3). Do not tighten. 9. Firmly push the deflector against the outer side of frame and tighten screws to 25-35 in-lbs (2.8-3.9 Nm) . 10. Remove left side mounting strap screw (2). 11. Install cable clamp (Figure 5, Item 9) to cruise control cable (if equipped). 12. See Figure 3. Insert screw through cable clamp (if necessary), washer (2) and left side deflector (6) and install to mounting strap speed nut. Firmly push deflector against outside of rail and tighten screw to 25-35 in-lbs (2.8-3.9 Nm) .

HARLEY DAVIDSON SHIFTER SHAFT COVER WITH INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1 2 4 3 5 6 7 is01872 1. Shifter shaft 2. Inner cover 3. Toe shifter lever 4. Outer cover 5. Set screw (for outer cover) 6. Set screw (for inner cover) 7. Casting Figure 1. Shifter Shaft Covers 1. See Figure 1. Remove the stock heel shift lever and toe shift lever (3) from the gear shifter shaft (1). 2. Install the set screw (6) into the inner gear shifter shaft cover (2). 3. Install inner gear shifter shaft cover with installed set screw over the casting (7) in-board of the shifter shaft (1). 4. Tighten the set screw until light contact is made with the casting. Do not overtighten. 5. Re-install toe shift lever on the gear shifter shaft. Tighten the shifter retaining screw to 18-22 lb-ft (24-30 Nm) . 6. Install the set screw (5) into the outer gear shifter cover (4). 7. Install outer gear shifter shaft cover with installed set screw over the end of the gear shifter shaft (1). 8. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw. SERVICE PARTS

Incoming search terms:

Incoming search terms: