reset ecm on 2007 efi sportster

You search Auto repair manual PDF reset ecm on 2007 efi sportster, if there are search results will appear below. If search results do not exist, please search by others keyword.



  reset ecm on 2007 efi sportster Direct Download speed 5282 Kb/s

  reset ecm on 2007 efi sportster Full Version speed 6162 Kb/s



2007-2010 Harley Davidson Dyna EFI Tuner INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2012

download
Remove the seat 2 Remove the left hand side cover (Fig. A). 3 Unplug the stock wiring harness connector from the ECM (Fig. B). 4 Move the data plug (Fig. B) out of the way to access bolt. 5 Remove the 3 bolts that hold the electrical box in place (Fig. B). 6 Slide the plastic box out from the frame. 7 Route the stock connector through to the back side of the electrical box (Fig. C). Fig. A Fig. B Fig. C Remove side cover Stock connector Stock connector Dat a plug Remove bolt Remove bolt s FM814 www .fuelmotousa .com 2007-20 1 0 Harley Davidson Dyna – FM EFI Tuner – 2 8 Lay the PCIII behind the electrical box temporarily. 9 Route the GREYconnector from the PCIII through the back of the electrical box and plug it into the ECM (Fig. D). 10 Connect the stock wiring harness to the BLACK connector of the PCIII. 11 Zip tie these connectors to the front side of the electrical box (Fig E). Make sure they are situated away from the rear exhaust pipe. Fig. D Fig. E PCIII connector Stock connector PCIII connector 12 Mount the PCIII to the underside of the stock ECM (Fig. F) using the supplied velcro. Make sure to clean both surfaces with the alcohol swab before attaching. Situate the PCIII so the USB and expansion ports point to the rear of the bike. This will allow you easier access to adjust the maps if necessary

Incoming search terms:

2007 Harley Davidson Sportster 1200 Installation Manual

0

Filed Under (Harley Davidson) by admin on 11-04-2012

download
1 Remove the stock seat. 2 Unplug the stock wiring harness from the ECM (Fig. A) . 3 Remove the ECM from the tray and remove the tray from the fender. You can reach underneath the fender to gain access to the release tabs for the tray. 4 Install the Dynojet tray into the rear fender . Make sure that all 3 location tabs are underneath the fender. 5 Lay the PCIII in the tray (Fig. B). 6 Install the stock ECM on top of the PCIII making sure that it is secured by the tray locking tabs. 7 Plug the GREYconnector from the PCIII into the ECM. 8 Route the PCIII harness on top of the GREY connector (Fig. C) and route towards the front of the bike. Fig. A Fig. B Fig. C 2007 Harley Davidson Sport ster 1200 – PCIII USB – 2 i817-51 1 www .powercommander .com Unplug Tray 9 Plug the BLACK connector from the PCIII into the stock wiring harness. Secure this connection with one of the supplied zip ties (Fig. D). 10 Run a zip tie behind the wiring harness (Fig. E). 11 Route the stock wiring harness as shown in Fig. E. Due to the lack of room on this bike this step needs to be exact or the install will not fit properly . Make sure that the harness coming from the GREYconnector is flush against the battery box. Acouple inches of this harness will be tucked underneath the frame

Incoming search terms:

2007 Corolla & Matrix 1ZZ-FE ENGINE NO START CONDITION REPAIR

0

Filed Under (Toyota Manuals) by admin on 01-11-2011

download
Refer to TIS, 2007 model year Corolla or Matrix Repair Manual: Engine Hybrid System – Engine Control – “1ZZ-FE Engine Control System: ECM: Removal” Engine Hybrid System – Engine Control – “1ZZ-FE Engine Control System: ECM: Installation” 2. Register the VIN into the replacement ECM (PCM). Refer to TIS, 2007 model year Corolla or Matrix Repair Manual: Engine Hybrid System – Engine Control – “1ZZ-FE Engine Control System: SFI System: Registration Some 2007 model year Corolla and Matrix vehicles equipped with a 1ZZ-FE engine may exhibit a “no start” condition. Improvements have been made to the Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) manufacturing process to reduce the possibility of this condition occurring. Please use the following procedure to repair the vehicle

Incoming search terms:

HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms:

HARLEY DAVIDSON EFI SCREAMIN' EAGLE BIG BORE EFI STAGE 2 KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
INSTALLATION Installation of this kit is divided into six steps: 1. Big-Bore Cylinder and Piston Conversion 2. High Performance Camshafts 3. High Performance Clutch Diaphragm Spring 4. High Performance Air Cleaner 5. Calibrate the ECM 6. Exhaust NOTES This Big-Bore Stage 2 kit is intended for High Performance applications only. This engine-related performance part is legal for sale or use in California on pollution-controlled motor vehicles. Engine-related performance parts are intended for the experienced rider only. -J04173 1 of 5 The air cleaner contained in these kits is designed to perform with these kits only. Any other combination of components is not confirmed to be legal for street use. The Product Information Label contained in this kit is required in the state of California only. This label is required to aid in passing the California Smog Check Program. Place the Product Information Label on the right side of the frame, directly beneath the VIN sticker. Do not place the label on motorcycles other than those specified in the Instruction Sheet. Gaskets provided in the 1690 conversion kit eliminate the need for original head gasket O-rings. For this reason, DO NOT install the Original Equipment (OE) O-rings (Part Number 11273) to the top of cylinder dowels, or severe engine damage may occur. Big-Bore Cylinder and Piston Conversion NOTE Installation of this kit requires removal of the cylinder heads, cylinders and pistons. Refer to Section 3, ENGINE: STRIPPING MOTORCYCLE FOR SERVICE and TOP END OVERHAUL of the applicable Service Manual for instructions. High Performance Camshafts NOTE Installation of this kit requires removal and re-installation of the cam support plate. Refer to Section 3, ENGINE: BOTTOM END Cam Support Plate, Removal and Disassembly/Assembly (Camshaft, Camshaft Bearings) of the applicable Service Manual for instructions. Measuring Piston-to-Valve Clearance After installing non-stock cams, check piston-to-valve clear- ance. 1. Apply 1/8-inch (3 mm) layer of clay to crowns of pistons in areas where valves meet pistons. 2. Refer to the appropriate Service Manual and assemble the heads and valve train, and tighten cylinder studs to torque specified. 3. Turn engine through two complete revolutions by hand. 4. Remove heads and measure clay at its thinnest point. NOTE Clay must measure 0.080 inch (2.03 mm) at its thinnest point. If this measurement does not meet minimum thickness, depth of valve notches must be increased. The depth of the notches must not exceed 0.135 inch (3.43 mm). Measuring Valve-to-Valve Clearance NOTE Wait ten minutes before turning the engine after installing push rods. This allows tappets to bleed down and prevents you from bending push rods or valves. 1. Rotate the engine so that both valves of the front cylinder are partially open. Shine a light through the exhaust port and look through the spark plug hole to view the valves. Turn engine, if required, to the point where the exhaust evel sensor to the fuel pump with screw (3). Tighten the screw enough to seat the fuel sensor against the mounting tab e. Route fuel level sensor wiring under the fuel hose and connect the fuel level sensor to the low fuel switch connector on the fuel pump module. If necessary use the jumper harness (Figure 4, item 5). f. See Figure 2. Secure the fuel pump wires and con- nectors

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE ELECTRONIC FUEL INJECTION (EFI) STAGE 1 KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
Installation NOTE The installation procedure is divided into three parts: 1) Replacing ECM (1996 and earlier models ONLY) 2) Calibrating the ECM 3) Replacing stock air cleaner with air cleaner from kit. 1) REPLACING ECM (1996 and earlier models ONLY) 1. Refer to the REMOVAL/REPLACEMENT section 9C in the 1995-1996 FLT Service Manual, Part No. 99483- 96A. 2. Install ECM in accordance with the installation procedure given in the Service Manual. 2) CALIBRATING THE ECM Have dealer recalibrate the ECM prior to starting vehicle. NOTE The product information (EO) label contained in this kit is required in the state of California only. This label is required to aid in passing the California Smog Check Program. Place the information label on the right side of the frame directly beneath the VIN sticker. Do not place the label over other product information labels. Do not place the label on motorcycles other than those specified in the instruction sheet. 3) REPLACING STOCK AIR CLEANER Removing Stock Air Cleaner NOTE Refer to the applicable Service Manual and check the warm- slow idle speed adjustment before removing stock backplate. 1. Remove stock backplate following the instructions given in the appropriate Service Manual. 2. See Service Parts Illustration. Retain stock air cleaner cover and buttonhead screw and washer. Installing High Performance Air Cleaner 1. See Service Parts Illustration. Locate banjo bolts (10) included with kit. Place one washer (11) over each banjo bolt. Insert bolts through holes in mounting bracket (15). Place a second washer over each bolt. Place manifold breather (16) over bolts with hose fitting toward rear of motorcycle. Install remaining washers over the ends of bolts

INSTRUCTIONS FOR PROGRAMMING KEYS INTO RE-FLASHED TOYOTA / LEXUS ECM

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

Download
After we re-flash the ECM it will be in “Automatic Registration Mode” when you install it. The ECM is
expecting that when first powered up (by turning on a key) that it will encounter 3 new keys. The first two keys
are internally (inside the ECM) designated as MASTER keys and the 3rd key inserted will be internally
designated as the VALET key. The ECM can be programmed with as few as 1 key. If less than 3 keys are
programmed into the ECM the security light may flash for some time (hours to weeks) until the ECM “learns”
that it is apparently not going to get any more keys.

Incoming search terms:

YAMAHA XV1700 PCR/ XV1700 PCRC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 02-12-2010

download
High beam indicator light “” 2. Right turn signal indicator light “” 3. Fuel level warning light “” 4. Engine trouble warning light “” 5. Left turn signal indicator light “” 6. Neutral indicator light “” 1. Speedometer INSTRUMENT AND CONTROL FUNCTIONS 3-4 3 EAU04436 Tachometer unit The electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range. The tachometer unit is equipped with the following: ● an odometer (which shows the total distance traveled) ● two tripmeters (which show the distance traveled since they were last set to zero) ● a fuel reserve tripmeter (which shows the distance traveled since the fuel level warning light came on) ● a meter lighting control ● a clock ● a self diagnosis device NOTE: ● Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons. ● To switch the odometer, the trip- meters and the fuel reserve trip- meter displays between kilometers and miles, press the “SELECT” button for at least two seconds. ECA00123 CAUTION: Do not operate the engine in the tachometer red zone. If operated in the red zone, the tachometer segments will start flashing to notify the rider. Red zone: 5,000 r/min and above 1. Tachometer 2. Clock 3. Odometer/tripmeter/fuel reserve tripmeter 4. “RESET” button 5. “SELECT” button 1. Tachometer red zone
INSTRUMENT AND CONTROL FUNCTIONS 3-5 3 Odometer and tripmeter modes Pushing the “SELECT” button switches the display between the odometer mode”ODO” and the tripmeter modes “TRIP 1″ and “TRIP 2″ in the following order: ODO→ TRIP 1 → TRIP 2 → ODO If the fuel level warning light comes on (see page 3-2), the odometer display will automatically change to the fuel reserve tripmeter mode “TRIP F” and start counting the distance traveled from that point. In that case, pushing the “SELECT” button switches the display between the various tripmeter and odometer modes in the following order: TRIP F → TRIP 1 → TRIP 2 → ODO → TRIP F To reset a tripmeter, select it by pushing the “SELECT” button, and then push the “RESET” button for at least one second. If you do not reset the fuel reserve tripmeter manually, it will reset itself automatically and the display will return to the prior mode after refueling and traveling 3mi (5km). Meter lighting control mode 1. Turn the key to “OFF”. 2. Push and hold the “SELECT” but- ton. 3. Turn the key to “ON”, and then after five seconds, release the “SELECT” button. 4. Push the “RESET” button to select the desired brightness. 5. Push the “SELECT” button to set the brightness level. 6. Turn the key to “OFF”. NOTE: When adjusting the meter lighting, the odometer display will indicate the brightness level. Clock mode To set the clock: 1. Push the “SELECT” button and “RESET” button together for at least two seconds. 2. When the hour digits start flashing, push the “RESET” button to set the hours. 3. Push the “SELECT” button, and the minute digits will start flashing. 4. Push the “RESET” button to set the minutes. 5. Push the “SELECT” button and then release it to start the clock. NOTE: ● After setting the clock, be sure to push the “SELECT” button before turning the key to “OFF”, otherwise the clock will not be set. ● To set the clock after the battery has been disconnected, first set the time to 1:00 AM, and then set the clock to the correct time

Incoming search terms:

2009 Harley Davidson Softail POWER COMMANDER V INPUT ACCESSORY INSTALLATION

0

Filed Under (Harley Davidson) by admin on 26-02-2012

download
1 Remove the seat 2 Uplug the stock wiring harness from the ECM (Fig. A) 3 Remove the 4 nuts that hold the ECM to the bracket and remove the ECM. 4 Remove the bolt that holds the seat strap to the rear fender. 5 Remove the ECM bracket from the fender. Remove one nut at a time or the bracket will fall into the tire. Reinstall the nuts to support the inner fender bracket. Due to the limited amount of room on this bike the seat strap and ECM bracket can NOTbe re-used. 6 Connect the PCVharness in-line of the stock wiring harness and ECM (Fig. B). 7 Place the BLACK PCVto GREYstock connector as close to the fuse box as possible. This connection will NOT lay flat against the frame. 8 Using the supplied velcro secure the ECM to the rear fender. Place the ECM as far down as possible. The upper part of the ECM will just overlap the bolt hole for the seat strap. Make sure to clean both surfaces with the alcohol swab before attaching. If using the Autotune kit offset the ECM about 1″ from center to the right side of the bike. 9 Remove the security module from the top of the battery (Fig. C). This unit slides to the right of the bike.

Incoming search terms:

All 2002 – 2007 Toyota & 2004 – 2007 Scion Models REPAIR MANUAL SUPPLEMENT VEHICLE PULLING TO ONE SIDE

0

Filed Under (Toyota Manuals) by admin on 23-05-2011

Download
Relationship Between Tire Characteristics and Vehicle Pulling to One Side When radial tires are rotating, they have the characteristic of generating force in the lateral direction between the tire and the road surface. This lateral force is comprised of two factors: S Ply-steer, which changes direction according to the rotation direction of the tires.
S Conicity, which is generated in a fixed direction regardless of the tire rotation direction. If these lateral forces are too strong, vehicle pulling will occur. A. Ply-Steer Lateral force due to ply-steer is produced by the construction of the belts inside the tire tread. With radial tires, the wire of the belt is slanted as shown in the illustration below. Thus, it is in the lateral direction that tire tread easily changes shape (stretches), and lateral force is generated between the tire and the road surface in the lateral direction.

Incoming search terms:

Incoming search terms: